balance work CCCF

Amount

M. BALANCE WORK AT CANCER CARE HOSPITAL

Civil and Finishes Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc.

Civil and Finishes Dismenteling / removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete

Civil and Finishes Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete.

Civil and Finishes Dismenteling / removing of structural steel including ridge, hips, valleys, jackarch, battens, arches, purlins, trusses, GI Sheet, Asbestos cemnt sheet, gutters, buillt up sections, etc. and stacking the material at sutaible place at site or as directed by Engineer Incharge.

Civil and Finishes Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete.

Civil and Finishes Providing internal cement plaster 12mm thick in single coat in cement mortar 1:5 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. directed by Engineer Incharge.

Civil and Finishes Providing sand faced plaster externally incement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using water proofing compound at 1Kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8mm thick incement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. directed by Engineer Incharge.

Civil and Finishes Providing and laying Vitrified Floor Tiles in different sizes and of approved make, with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with epoxy grouts of 3mm width and with white cement & matching pigments etc. complete at specified locations as directed by Engineer in charge and complete. (Payment for grouting of joints to be made separately) Size of Tile 600mm x 600mm.

Civil and Finishes Providing and laying Vitrified tiles in different sizes and of approved make, with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, as approved by Engineer- in- charge, in dado, skirting, riser of steps, over 12mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600mm x 600mm./ 600mm x 300mm

Civil and Finishes Providing and applying gypsum plaster (withGypsummaterial )with finishing with gypsum material in10to13millimeter thickness to previously plastered surface/oron newly brick surface(Excludingroughcastplaster)in all position including preparing and Finishing the surface scaffolding etc.complete.directed by Engineer Incharge.

Civil and Finishes Providing and applying 2 coats of Washable, Anti-bacterial, Anti-fungal premium interior water based washable emulsion conforming to IS 15489 standard with washable & cleanable ability more than 4000 mechanical cyces; with VOC below 3% by mass; along with anti-fungul resistance conformance to ASTM D3273; and anti-bacterial resistance conformance to JIS Z 2801:2010 and coverage of 120-140 sq ft/ltr applied over one coat of Interior Sealer A700 or equivalent as per recommended application procedure Rate to be inclusive of 1 Coat of Primer + 2 Coats of Putty + 1 Coat of Primer. Approved Make Dulux Professional Solitaire or equivalent from Asian Paints, Berger StainResist or equivalent from Asian Paints, Berger Supply and Application cost of Paint to be Rs 255 per Sqm including taxes and delivered at site.

Civil and Finishes Painting and applying Exterior grade Texture Paint in desired Texture pattern and shade / colour of paint to the exterior walls / ceiling / RCC surfaces / any other location as desired by the EIC after preparation of the wall / RCC surfaces to the external surfaces of the building, filling in cracks with approved putty, with necessary one coat of primer as per the manufacturer specification, one / two coats of texture and min two coats of exterior grade paint including scaffolding, preparing the surface, curing, primer coat etc complete. Final Coat Paint should be done before Handing Over

Civil and Finishes Providing and laying Autoclaved Aerated Cement blocks masonry with 100mm / 150mm / 200mm / 230mm / 300mm thick AAC blocks up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineering-Charge. (The payment of RCC band and reinforcement shall be made for separately)

Civil and Finishes Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, includingremoving the excavatedmaterial up to a distance of 50m. beyond the building area andstacking and spreading as directed, dewatering, preparing the bed for the foundation and necessarybackfilling,ramming,watering includings horing and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means directed by Engineer Incharge.

Civil and Finishes Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Civil and Finishes Providing and fixing in position TMT-FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings andschedules. includingcutting, bending,hookingthebars, binding with wires or tack welding and supporting as required complete. directed by Engineer Incharge.

Civil and Finishes Providing and constructing O/H storage of 450mm depth and size as per drawings, with top, sides, bottom, back, all vertical and horizontal intermediates, shutters, edges all as per detail drgs. All external surfaces to be finished in approved laminate, with balancing laminate on the interior surface. All exposed edges for intermediates to be in PVC edge binding / post formed. Rate to include hardware such as approved locks, auto closing hinges for shutters, approved handles, door stop, tower bolt, etc. complete. (Carcase made in exterior grade MDF) directed by Engineer Incharge.

Civil and Finishes Stainless Steel Rack and Tray Providing and fixing storage in 20 gauge Stainless Steel (SS) grade -304 slotted angle of 35mmx35mm finished with approved shade powder coating with 450mm wide inclusive of necessary powder coated nut-bolt fittings, edge guard bush for slotted angles etc complete as directed. The standard size of the slotted angle to be 900x1800mm with 4 Nos. of vertical shelves (approximate size. Please check at site)Approved Make: Steeledge / Kompress / Godrej / Space Planner or directed by Engineer Incharge. (Elevation area to be considered for measurment purpose)

Civil and Finishes Providing and fixing factory finished Factory Finished DB Shutters (300mm - 450mm deep) in 19mm thick Exterior grade MDF finished in approved shade laminate on exposed surface and balancing laminate on the interior surface with PVC edge banding from Rehau make or matching colour polish. Rate to be inclusive of back, sides, top, bottom in fire rated ply and finished approved laminate as directed and framework in seasoned teak wood of section 50mm x 100mm, finished in colour polish matching the colour of the laminate. Rate to be inclusive of approved handle, tower bolts, Locks, magnetic ball-catch etc complete as directed. Each shutter shall have CNC Cut MDF louvers (Paint finished) at the bottom and one at the top. Rate to be inclusive for above the storage upto the false ceiling ply boxing finished as per shutter. MODE OF MEASUREMENT TO BE SURFACE AREA OF OPENABLE SHUTTERS ONLY. a directed by Engineer Incharge..

Civil and Finishes Providing and fixing Trap door in the false ceiling for HVAC in 19mm thick marine plywood cladded with 4mm thick exterior grade MDF and finished in three coats of approved Acrylic Emulsion paint, inclusive of 19mm thick marine ply framework finished in matching paint. All the edges to be of teak wood lipping and finished in approved melamine. The rate to be inclusive of necessary 19mm thick plywood support from ceiling etc. complete. directed by Engineer Incharge.

Civil and Finishes MGPS Valve Box Closing-Providing and fixing Screen, madeup in 100mm x 50mm x 1.7mm thick Aluminium Box section and Ply , trench cover and supports. directed by Engineer Incharge.

Civil and Finishes Providing and fixing of fabric wrapped 12mm thick Soft board panels of approved make on the existing ply backing of required sizes as per architectural drawings including making necessary cut out / opening in existing gypsum board partitions for fixing the same. The panels to be finished with fabric (Basic rate to be Rs 350 per Rmt including taxes) of approved shade, colour and make. 2mm thick foam of approved make to be infill between board and fabric as per architectural drgs. Fabric shall be stretched uniformly along the direction of weave and shall be wrinkle free and all edges to be finished in PVC wall gripper of WALL TRACK or equivalent make etc complete and as directed by Engineer in charge.

Civil and Finishes Indor Plants with Decorative Pots SUPPLY ,PLANTING AND MAINTAINACE OF PLANT SPECIMEN TREES Supply of healthy sapling, vigorous specimen, well shaped, healthy fronds and well established and Planting of plant specimen including, loading, unloading of plant from project area to desired locations,support stacking guying, basin preparation for irrigation,watering and removal of unserviceable material’s as per direction of Engineer-in-charge Including lifting, loading, unloading of plant to Project site and maintaince of plants in healthy conditions till plantation. (excluding cost of plant & water)etc. Maintaining till handover by cleaning, watering, weeding, pruning ,stirring of soil, staking, replacing casualties etc. Complete.as per directive given by engineer incharge. Note: 1. Plantation included SIX months casuality replacement (Free of cost). 2. Water source shall be provide by client. TREE SPECIMEN Height-500-700 Canopy-200-500 Stem dia- 20-30 mm DBH Clear Stem ht-600

Civil and Finishes Kerb Stone painting works -Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.as per directive given by engineer incharge.

Civil and Finishes Providing and applying two coats of lead/zinc base oil paint/ bituminious paint of approved colour to new structural steel work and iron work in buildings including scaffolding if necessary, cleaning and preparing the surface etc. complete. (Including primer coat).

Civil and Finishes Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with river sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer's specifications & direction of Engineering-Charge. 60mm thick C.C. paver block of M-35 grade with approved colour, design & pattern. or directed by Engineer Incharge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Civil and Finishes Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) or directed by Engineer Incharge.

Civil and Finishes Providing second class Burnt Brick masonry with conventional / I.S. type bricks in cement mortar 1:4 including scaffolding, racking out joints and watering etc. in pillar of rectangular shapes as shown in the drawings or as directed complete.

Civil and Finishes Providinga nd fixing of Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) 25mm thick

Civil and Finishes Construction of Granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53mm to 0.075mm) having CBR Value-25

Civil and Finishes Cleaning or washing of existing bituminious road surface including cleanig of dust, watering, Cleaining of road surface by vacume pump, etc. completed or as directed by Engineer Incharge

Civil and Finishes Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. On bituminous surface @ 0.75 Kg / sqm

Civil and Finishes Providing and laying of Type - B premix seal coat with HMP of approprate crushed stone chipping 6.70 mm size and penetration bitumen of specified grade @ 0.68 Kg / Sqm. , preparing existing road surface including mixing in suitable Batch Mix plant and rolling by static roller having weight 8 to 10 MT. etc. complete. (VG-30 bulk bitumen rates are considered to arrive at rates)

Civil and Finishes Providing and layying of 25mm compacted thickness with bitumen of grade VG- 30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Civil and Finishes Road marking strips-Providing and applying 2.5mm thick road marking strips (retroreflective) of specified shade / colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour ,T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.as per directive given by engineer incharge.

Civil and Finishes Repair to pot holes or patch repair by removal of failed material, trimming the sides to vertical and levelling the bottom, cleaning the same with compressed air or any appropriate method filled with 75mm B.M, applying bitumen tack coat at the bottom and vertical sides as per as per MORTH specification clause 3004.1 and 3004.2

Civil and Finishes Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

Civil and Finishes Providing and fixing polycarbonate roofing sheet of 6 mm thick for roofing as per required colour including fastening and with accessories like screws and bolts as per drawing etc. complete or directed by Engineer Incharge

Civil and Finishes Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished granite stone, machine cut for kitchen / pantry platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Civil and Finishes Providing & fixing of Corner guard 90 degree with cap inside amouminium thickness not less than 2 mm standard specification & approved by Architect. Rate has to be inclusive of all required necessary hardware & fittings as required & instructed by architect. Rate shall be include with all material shifting, temporary stand & scaffolding where ever required as per instruction by architect & PMC (Required material test certificate along with supporting document) Rate shall be include with material movement & shifting for all the floors. Basic Rate to be Rs 700 per Rmt including taxes and delivered at site..

Civil and Finishes Removing grass, gazer grass and disposing off out of building and trenches cleaning making clean the ground by shovel and phavaras etc. complete. Or directed by Engineer Incharge

Civil and Finishes Providing and fixing marine plywood 710 Grade marked 12 mm thick of approved make to existing framework, backing or studding with screws for additional support on existing dry wall for installtion of TV etc. complete or as directed by Engineer-in-charge.

Civil and Finishes Providing and fixing Flag Hosting Pote and Stagging in Circular steps as per the directions of Engineer-in-Charge. The Flag Hosting Pipe shall be of Staleness Steel and Staging shall be of civil works, painted white etc complete

Civil and Finishes Gypsum Board False Ceiling-Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making cove a vertical brand and openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge .Including the cost of painting with 2 coats of primer 2 coats of putty 2 coats of antimicobial paint at all height upto satifaction of PM incharge .cove not be measured seperately only plan area to be measured. 12.5mm thick tapered edge gypsum plain board conforming to IS:2095- Part I

Civil and Finishes Tree relocation of healthy sapling, vigorous specimen, well shaped, properly branched and well established and Planting of shrub specimen including, loading, unloading of shrub from project area to desired locations, support stacking guying, basin preparation for irrigation, watering and removal of unserviceable material’s as per direction of Engineer-in-charge Including lifting, loading, unloading of plant to Project site and maintaince of plants in healthy conditions till plantation. (excluding cost of plant & water)etc. Maintaining till handover by cleaning, watering, weeding, pruning ,stirring of soil, staking, replacing casualties etc. Complete. Note: 1. Plantation and Tree relocation of plants and shurbs etc. 2. Water source shall be provide by client. TALL HEIGHT SHRUB PLANTATION Height:1m-2m Canopy:450-600

Civil and Finishes Providing fixing and installation of water proofing course whereever required using as pre approved methodology by FOSROC, BASF or any other renound chemical waterproofing agency. (Any of the work required 10 years performance gurrantee bond must be signed on non judiciary stamp paper in the favour of CCCF )

Civil and Finishes Providing and applying Core Cutting activity for new core of various sizes from 75 mm to 200 mm.

Civil and Finishes Fixing or laying of floor tiles or wall tiles work at required places as per directive given by Engineer Incharge

Civil and Finishes WATER METER SIDE- WASTE MATERIAL LEVELLING WORK: Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by muncipal board complete with bolts,nuts rubber, insersions etc. ( the tail plases if required will be paid seperatly )as directed by engineer incharge. 100 mm nominal bore

Electrical Works SIGNAGE WIRING EXTERNAL &INTERNAL ROOM Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. directed by Engineer Incharge. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Electrical Works EARTHING PIT REWORK Providing and fixing 25 mm X 5 mm G.I. strip on surface or inrecess for connections etc. as required accesorries. directed by Engineer Incharge.

Electrical Works DDC PANEL WIRING WITH SOCKET &BMS DDC wiring. Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. directed by Engineer Incharge. Wire

Electrical Works BURY OF HT CABLE (NEAR VCB ROOM) 300 sqmm Aluminium Cable &external LT Cable Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. directed by Engineer Incharge. Above 120 sq. mm and upto 400 sq. mm

Electrical Works Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.as per directive given by engineer incharge. Upto 35 sq. mm

Electrical Works WATER TANK SUPPLY - SUPPLY OF CABLES - XLPE INSULATED, FR-LSH PVC SHEATHED COPPER CONDUCTOR ARMOURED CABLES (IS:7098 Part-I) Supply of following sizes of 1.1kV grade XLPE insulated, Extruded FR-LSH PVC inner sheath Type ST-2, FR-LSH PVC outer sheath Type ST-2, stranded Copper conductor, Armoured cables as per IS:7098 Part-I.as per directive given by engineer incharge. 4C x 6 sq.mm.Cu. Ar. XLPE cable

Electrical Works LAYING OF CABLES- ON EXISTING TRAYS/ IN EXISTING DUCTS/ IN EXISTING CIVIL TRENCHES (IS:7098 Part-I) Laying, Fixing, Testing & Commissioning of following sizes of 1.1kV grade XLPE insulated, Extruded FR-LSH PVC inner sheath Type ST-2, FR-LSH PVC outer sheath Type ST-2, stranded Copper conductor, Armoured cables as per IS:7098 Part-I on existing cable trays/ in existing hume pipes/ PVC pipes/ GI pipes/ on surface of slabs, walls or masonary/ RCC trenches/ ducts including cables ties, GI saddles, clamps and necessary hard ware. directed by Engineer Incharge. 4C x 6 sq.mm.Cu. Ar. XLPE cable

Electrical Works CABLE TERMINATION (IS:7098 Part-I) Cable end Termination of following sizes 1.1kV grade XLPE insulated, Extruded HR PVC inner sheath Type ST-2, FR-LSH PVC outer sheath Type ST-2, stranded Copper conductor, Armoured cables as per IS:7098 Part-I including cost of tinned copper, heavy duty crimpping lugs, double compression glands, insulation tape and all necessary material to complete the termination. directed by Engineer Incharge. 4C x 6 sq.mm.Cu. Ar. XLPE cable

Electrical Works Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. directed by Engineer Incharge. Module (200mmX75mm)

Electrical Works MCB,BOX Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing an commissioning etc. as required. directed by Engineer Incharge.. Triple pole and neutral

Electrical Works Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. directed by Engineer Incharge. Upto 120 sq. mm

Electrical Works Supply and installation of LUGS FOR TERMINATION. as directed by engineer in charge. Copper Lugs 35 Sq.mm Plam Type

Electrical Works Supply and Installation of LUGS FOR TERMINATION. as directed by engineer in charge. Copper Lugs 70 Sq.mm Plam Type

Electrical Works Supply and Installation of LUGS FOR TERMINATION. as directed by engineer in charge. Copper Lugs 50 Sq.mm Plam Type

Electrical Works Supply and Installation of LUGS FOR TERMINATION. as directed by engineer in charge. Copper Lugs 95 Sq.mm Plam Type

Electrical Works Supply and Installation of LUGS FOR TERMINATION. as directed by engineer in charge. Copper Lugs 240 Sq.mm Plam Type

Electrical Works Supply, testing, installation and comissioning of Net Meter,ABT Meter, Combiner Box,Genration Meter and CTPT etc. as per drawings and designing. Directive by engineer in charge. directed by Engineer Incharge.

Electrical Works Supply, of copper cable approved make or as Dirtected by engineer in charge. Size of copper cable 1C X 50 Sq.mm

Electrical Works Supply, of copper cable approved make or as Dirtected by engineer in charge. Size of copper cable 1C X 70 Sq.mm

Electrical Works Supply, of copper cable approved make or as Dirtected by engineer in charge. Size of copper cable 1C X 240 Sq.mm

Electrical Works Supply, of copper cable approved make or as Dirtected by engineer in charge. Size of copper cable 2C X 50 Sq.mm

Electrical Works Conduits Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit directed by Engineer Incharge. Size 25 mm

Electrical Works Electrical points including wires Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. directed by Engineer Incharge. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Electrical Works Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc directed by Engineer Incharge. 3 Module (100mmX75mm)

Electrical Works Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc directed by Engineer Incharge. 6 Module (200mmX75mm)

Electrical Works Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. directed by Engineer Incharge. 5 pin 16 amp socket outlet

Electrical Works Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. directed by Engineer Incharge. 5 pin 6 amp socket outlet

Electrical Works Fire Supression System for Hub Room and Server Room TOTAL ROOM FLOODING SYSTEM Supply, Installation, Testing and Commissioning of 1x34 Itr completely CCOE approved high pressure seamless BIS 7285 approved Cylinders having 34 ltr capacity, UL/FM/VDS approved FK5-1- 12 clean agent gas with UL/FM/VDS listed valve assembly and electric solenoid switch. The system also to be fitted with low pressure supervisory switch for monitoring cylinder pressure gauge with safety burst disc safety cap, elbow and other accessories, mounting bracket, container straps, NRV , Pressure operated control head which shall allow for pressure actuation of gas mounted, manually operated actuator to actuate the gas flooding process with the help of a lever, flexible rubber hose with wire bralded enforcement to route the gas from the storage cylinder to the discharge piping, to be connected to the discharge outlet of gas cylinder valve & to be terminated at the system piping or discharge manifold, Flexible actuation hose complete as required. Discharge nozzle, 180/360 degree. Designated to provide proper flow rate & distribution FK5-1-12 gas to flood the hazard area as per latest NFPA 2001 requirement. Piping ASTM grade A 106 schedule 40 with fittings & supports and Gas Release Panel compatible to directed by Engineer Incharge. Fire Alarm System. (HUB ROOM- GF ) Complete Installation, Testing and Commissioning of above Items

Electrical Works Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. directed by Engineer Incharge. 100Amp,30KA,FPMCCB

Electrical Works Providing and fixing Male connector schnider make 81282 3P+N at required place

Electrical Works Providing and installation of flood light for terrace including 110 Watt or as directed by Engineer Incharge

Electrical Works Point wiring in for light/fan/bell in 20 mm metal conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire,flush type switch, earthing and required accessories as per specification no. WG-PW/SW

Electrical Works Providing and installation of alluminium cable 4C X 25 Sqmm for DX unit

Electrical Works Providing and fixing U/V Filters for Flow: 250LPH UV Dose: >300J/m2 UVT: 98% HSN Code: 84212190

Electrical Works Providing and fixing U/V Filters for Flow: 2000LPH UV Dose: >300J/m2 UVT: 98% HSN Code: 84212190

Electrical Works Supply and laying including termination of voice/data cabling in existing conduits including terminations: Cat 6A cabling

Plumbing Works DIALYSIS machine facilities Providing and fixing on walls/ ceiling/ floor 32mmdia. uPVC pipe with necessary fittings, remaking good the demolished portion etc.complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed by Engineer Incharge. etc. complete.

Plumbing Works WATER TANK SUPPLY LINE Supply, Installation, Testing and Commissioning of Piping Network UPVC Pipe 63mm OD-6kg/cm2 etc. completed or directed by Engineer Incharge.

Plumbing Works WATER TANK SUPPLY LINE Supply, Installation, Testing and Commissioning of Piping Network UPVC Pipe 50mm OD-6kg/cm2 etc. completed or directed by Engineer Incharge.

Plumbing Works WATER TANK SUPPLY LINE Supply, Installation, Testing and Commissioning of Piping Network UPVC Pipe 40mm OD-6kg/cm2 etc. completed or directed by Engineer Incharge.

Plumbing Works HAND RAIL SHOWER AND EYE WASH COCK(SECOND FLOOR) Providing and installation of eye wash as per drawings and designing as per engineer in charge

Plumbing Works Supply and Installation of 20 mm diameter Elbow or as directed by Engineer Incharge

Plumbing Works Supply and Installation of 32 mm Elbow or as directed by Engineer Incharge

Plumbing Works Supply and Installation of 20 X 15mm Brass elbow or as directed by Engineer Incharge

Plumbing Works Supply and installtion of 32X15mm Brass Elbow or as directed by Engineer Incharge

Plumbing Works Supplya nd installation of 32 mm Socket or as directed by Engineer Incharge

Plumbing Works Supply and Installation of 20 mm Socket or as directed by Enginner Incharge

Plumbing Works Supply and installation of 20 mm size tee or as directed by Engineer Incharge

Plumbing Works Supply and installation of 32 mm size tee or as directed by Engineer Incharge

Plumbing Works Supply and installation of 20 mm size FTA or as directed by Engineer Incharge

Plumbing Works Supply and Installation of 32 mm FTA or as directed by Engineer Incharge

Plumbing Works Supply and installation of 20 mm MTA or as directed by Engineer Incharge

Plumbing Works Supply and installation of 32 mm MTA or as directed by Engineer Incharge

Plumbing Works Supply, installtion, testing and commissioning of UV lamp of minimum capacity 2000LPH and minimum lamp wattage 15W

Plumbing Works Providingand fixingonwalls/ ceiling/ floor 50mmdia. CPVCpipewithnecessary fittings, remaking good the demolished portion etc. complete.

Plumbing Works SOLID WASTE DISPOSAL Removing grass, gazer grass and disposing off out of building premises including making clean the ground by shovel and phavaras etc. complete.as directed by engineer incharge

Testing Works Providing testing installation and comissioning of Medical Gas Oxygen Cylenders as per required qty.as directed by engineer incharge 1 D Type Empty Oxygen Cylinder (Capacity-46.7 Liter)

Testing Works Providing testing installation and comissioning of Medical Gas Oxygen Cylenders as per required qty.as directed by engineer incharge D Type Empty N2O Cylinder (Capacity-46.7 Liter)

Testing Works Providing testing installation and comissioning of Medical Gas Oxygen Cylenders as per required qty.as directed by engineer incharge D Type Empty N2O Cylinder (Capacity-46.7 Liter)

Testing Works Liquid Petrolium Gas (LPG) Third party test

Desing, Supply, Configure, Testing and Commissioning Electrical Low Voltage works as per the Attachment No 01

Providing staging and scaffolding as per the industrial standards upto 15 meters height including construction and disentailing etc complete. Decision of Engineer In Charge will be final and binding.

Provinding, laying and termination of 4 or 3 - 1/2 Core 300 MM Copper insulated cable as per the make and standard for connection of DG sets with Isolator Panels and other location as per the instructions of Engineer in-Charge. Etc completed.

D.R. Engineering Services (BID ID -6486334)

Adhunik Electrical Services (BID ID -6491933)