Repair and maintenance of Residential Qtrs (Type-I Qtr 05 Nos., Type-II Qtrs 15 Nos. and Type-III Qtrs 04 Nos.) at 19 Bn BSF under SHQ BSF Abohar

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Kiln seasoned and chemically treated hollock wood 30 mm thick

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge. 9.130.1 With decorative veneering on one side and commercial veneering on other side

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes

15 mm cement plaster on rough side of single or half brick wall of mix: 13.5.1 1:4 (1 cement: 4 coarse sand)

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One coat

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.With cement mortar 1:4 (1cement: 4 coarse sand)

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 40 mm nominal dia Pipes

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT bib cock of approved quality and colour.15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT bib cock of approved quality and colour. 15 mm nominal bore, 165mm long. Weighing not less than 110 gms.

Providing and applying white cement based putty of average thickness 0.5 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing CPVC gate valve for water supply line of approved quality of 25 mm nominal bore as per direction of engineer -in -charge.

Providing and fixing CPVC gate valve for water supply line of approved quality of 40 mm nominal bore as per direction of engineer -in -charge.

Providing and fixing CPVC Union in water supply pipe line including cutting and threading the pipe with all complete 20 mm nominal bore as per direction of engineer -in -charge.

Providing and fixing CPVC Union in water supply pipe line including cutting and threading the pipe with all complete 25 mm nominal bore as per direction of engineer -in -charge.

Providing and fixing CPVC Union in water supply pipe line including cutting and threading the pipe with all complete 40 mm nominal bore as per direction of engineer -in -charge.

Providing and fixing PTMT tank nipple of approved quality for polyethylene water storage tank with fitting all complete : 25 mm nominal bore as per direction of engineer -in -charge.

Providing and fixing PTMT tank nipple of approved quality for polyethylene water storage tank with fitting all complete : 20 mm nominal bore as per direction of engineer -in -charge.

Making connection of CPVC distribution branch with CPVC main of following sizes by providing and fixing tee, including cutting the pipe etc. complete : 40 to 25 mm nominal bore

Making connection of CPVC distribution branch with CPVC main of following sizes by providing and fixing tee, including cutting the pipe etc. complete : 20 to 15 mm nominal bore

Providing and fixing of PVC pipe having working pressure 6kg/cm^2 use as rain water pipe : 110 mm dia of make Supreme/Finolex/Kisan/ Prince.

Providing and fixing of PVC door bend having working pressure 6kg/cm^2 use as rain water pipe : 110 mm dia of make Supreme/Finolex/Kisan/ Prince.

Providing and fixing of PVC plain bend having working pressure 6kg/cm^2 use as rain water pipe : 110 mm dia of make Supreme/Finolex/Kisan/ Prince.

Providing and fixing of PVC door tee having working pressure 6kg/cm^2 use as rain water pipe : 110 mm dia of make Supreme/Finolex/Kisan/ Prince.

Providing and fixing of door PVC plain tee having working pressure 6kg/cm^2 use as rain water pipe : 110 mm dia of make Supreme/Finolex/Kisan/ Prince.

Providing and fixing with MS flat size 20 mm x 4 mm clamp for holding 100 mm dia horizontal rain water pipe including all complete fittings as per site requirement as per direction of engineer in charge.