Supply of Material and labour work (Balance work)

Amount

SANITARY

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Range of two half stall urinals with 5 litre P.V.C.automatic flushing cistern

Range of three half stall urinals with 10 litre P.V.C.automatic flushing cistern

Range of four half stall urinals with 10 litre P.V.C.automatic flushing cistern

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required610x510 mm bowl depth 200 mm

Kitchen sink with drain board: 510x1040 mm bowl depth 250 mm

Providing and fixing P.V. C. Pipe 6kg.Pis including all Material, Labour T.&P. Complete of work.110 mm dia.

160 mm dia

Providing and fixing P.V. C. Bend including all Material, Labour T.&P. Complete of work.For 110 mm dia.

160 mm dia

Providing and fixing P.V. C. N Trap including all Material, Labour T.&P. Complete of work.100*100mm.

Providing and fixing P.V. C. P Trap including all Material, Labour T.&P. Complete of work.100*100mm.

Providing and fixing of P.V.C. Copler For 110 mm dia.

160 mm dia

Providing and fixing of P.V.C. Door Tee/Tee/R.TeeFor 110 mm dia.

160 mm dia

Providing and fixing of P.V.C. Y Door Tee/TeeFor 110 mm dia.

Providing and fixing of P.V.C. Door Bend For 110 mm dia.

160 mm dia

Providing and fixing of P.V.C. Clamp For 110 mm dia.

160 mm dia

Providing and fixing of P.V.C. Covel 110mm. Ddia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVCplain & brass threaded fittings This includes jointing of pipes & fittingswith one step CPVCsolvent cement, trenching, refilling & testing joints complete as per direction of Engineer in Charge. - Exposed on wall: 15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

Same as above but Concealed work, including cutting chases and making good the walls etc. 15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :30 cm length 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) '32 mm nominal bore

50 mm nominal bore

Cutting holes upto 30x30 cm in walls including making good the same :With F.P.S. bricks.

Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.

Providing & Placing of polyethylene waterstorage tank, ISI 12701 locking arregment and making necessary holes for inlet, outlet and overflowpipes but without fittings.

Providing & Making of Platefom for 1000 Ltr. P.V.C. Water Storege Tank.

Providing & Fixing of 8mm. Thick Urinal Glass Partition including all Fittings complete

External sanitary

Providing & Laying of 160mm. Dia P.V.C. pipe 6kgcm Sewer Line including excavation of Tranch Providing 1:4:8 cement Concrete P.C.C. Base & Pipe covered allaround with P.C.C. 1:2:4 including all Labour, T.&P. complete of work

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat\ of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc '50mm Dia

32 mm dia

25 mm dia

20 mm dia

15 mm dia

CIVIL WORK

Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including all labour and T & P etc. required for proper completion of work. (Labour only)

Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including , labour and T & P etc. required for proper completion of work. (Labour only)

10mm. Thick Ceiling Plaster with 1:3 cement : C.sand Mortor including , Labour T.&.P. complete of work .(Labour only)

12/15mm wall plaster 1:6 cement :coarse sand with groove at junction including labour T&P etc. (Labour only)

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge.Granite work (paid for double moulding only)

Providing and fixing of 2mm. Thick Section Powder Coated aluminium work for Window / Door with extruded built up standard tubular sections and other sections of approved make fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all completeWindow

S/L Door

D/L Door

Cement washing (white cement) one coat onwall or ceiling whereever required

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size asapproved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) andjointing with grey cement slurry @ 3.3kg per sqm, including pointingin white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.

roviding and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed fromM.S. sheets and galvanized with zinc coating of 120 gms/sqm (bothside inclusive) as per IS:277 and consisting of angle cleats of size25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm centre to centre, one flange fixed to the ceiling with dashfastener 12.5 mm dia x 50mm long with 6mm diabolts, other flangeof cleat fixed to the angle hangers of 25x10x0.50 mm of requiredlength with nuts & bolts of required size and other end of anglhanger fixed with intermediate G.I. channels 45x15x0.9 mm runningat thespacing of 1200 mm centre to centre, to which the ceilingsection 0.5 mm thick bottom wedge of 80 mm with tapered flangeof 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular toG.I. intermediate channelwith connecting clips made out of 2.64 mm dia x 230 mm long G.I.wire at every junction, including fixing perimeter channels 0.5 mmthick 27 mm high having flanges of 20 mm and 30 mm long, theperimeter of ceiling fixed to wall/partition with the help of rawl plugsat 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with thehelpof dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointingcompound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with'2.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIScertification marks)

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes110 mm diameter

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.110 mm Shoe

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sum. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

Providing & Applying Two Coat White Cement Based Wall care Putty For Given Smooth surface for Painting complete of work.

Supply and Filling of cinder /AAC bats filling .

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.'Hot finished welded type tubular truss

providing and fixing of 10 mm thick Polycarbonate sheet roofing with provision of al.jointing cover at each joint complete in all respectAs per site requirement

Electrical item

Supply of VRF air-conditioning system comprising of following items:'Supply of Indoor units address setting and capacity as mentioned below. multispeed motor, copper coil section with DX coil, outer cabinet, drain pan mechanism insulation, pipe connections and fresh air intake connector as per specification with electronic expansion valve including cordless/corded remote high wall split with wirless remote. make- HitachiVRF HI-WALL :1.64 TR/2 HP

VRF HI-WALL :2.0 TR/2.5 HP

4 WAY CASSETTE :2.46 TR/3.0 HP

4 WAY CASSETTE :3.2 TR/4.0 HP

High Static Ductable Units 20 HP

High Static Ductable Units 10 HP

Supply of Multikit Joints-Indoors

Supply of Multikit Joints-Outdoors /circuit

12.5 % bulkage will be deduct from course sand

All rates are F.O.R. Site i/c loading unloading & stacking

Rs 55.00 per cu.m / floor for each floor above G.F. shall be paid extra on brick work

Rs 1.70 per Sq.m / floor for each floor above G.F. shall be paid extra on plaster

Materials

Course sand (Hameerpur)

Brick

Cement PPC (packed in 50 kg bag) make- Birla,Prism, ACC, Mycem,J.P.

M/S SURAJ ENTERPRISES