Balance work of Science Lab in GSSS Garola

Amount

Excavation in drains and channels etc; in earth work in all kind of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturated soil including chiseling or any other mixed variety of soil, including shoring, shuttering, de-watering and pumping out water upto any depth or any quontam of water including slush which may be arise during the de-watering removal of slush and stacking the serviceable and un-serviceable material clear from edge of excavation as per direction of Engineer-In-Charge and then returning the stacked soil in 15cm (fifteen centimeter) layer when required into plinths sides of foundations etcetra consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- In charge, within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rates inclusive of octori, royality, Malkhana, toll taxes, GST and any other taxes imposed by the Government.

Sand filling under floor including watering, ramming, consolidating and dressing complete as per HP.PWD., Specification and approved drawing and as per entire satisfaction as directed by Engineer-In Charge, including carriage of material within all leads & Lift and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings as per Architectural drawing and the like within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts Square, rectangular or polygonal in plan within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders and lintels sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depths within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Vertical surfaces such as walls (any thickness) partitions and like within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls under any thickness within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:6:12 (One cement isto Six sand isto Twelve graded broken/crushed stone aggregate 40mm (Forty millimeters) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth, within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (One cement isto five sand isto ten graded broken/crushed stone aggregate 40mm (Forty millimeters) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth, within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement isto Four sand isto Eight graded broken/crushed stone aggregate 40mm (Forty milimetres ) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landings, shelves their supports balconies, beams, girder, bressumers and cantilevers in all depth / thickness upto all floor level etc; within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars posts and struts for all floors heights in all depth / thickness within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete in reinforcement work for reinforced concrete Chhajjas for all thickness in all floor levels up to all heights and all thickness including finishing the exposed surface with cement mortar 1:3 (One cement : Three sand) to give a smooth and even surface including centering/ form work and curing complete but excluding the cost of reinforcement for reinforced concrete work up to all floors level up to all height as per direction of Engineer-In-charge. within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying reinforcement concrete work M-20 (M-twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) mechanically mixed and vibrated to give smooth and even surfaces including centring and shuttering etcetra but excluding the cost of reinforcement as in mouldings as in cornices, windows sills etc not exceeding 15cm (Fifteen centimetres) in girth as per approved specification, drawing and design complete upto floor all level within all leads, lifts of materials and other. incidentals and as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in in walls including attached buttresses, pilasters and their caps and basis and string courses etcetra in all depth / thickness upto all floor level etcetra within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying Damp Proof Course 100mm (One Hundred milimetres) thick with cement concrete 1:2:4 (one cement: two sand: four graded crushed stone aggregate 12.5mm (Twelve decimal five milimetres nominal size) and curing complete, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Applying a coat of hot bitumen mexphalt 80/100 (Eighty/Hundred) or equivalent using 1.70 Kgs. (one decimal seventy Kilogram’s) per square metre. On Damp Proof Course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil; within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing Tor steel reinforcement of Sail / Tisco for reinforced cement concrete work including bending, binding, straighting, cutting and placing in position complete including cost of binding wires complete for all floors within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Second class brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6 (One cement isto Six sand) within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Second class half brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:4 (One cement isto four sand). within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including rakcking out joints with cement mortar 1:6 (One cement isto Six sand) and curing complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 40mm (forty millimeters) thick factory made I.S.I. marked NO. IS 1003 flush door shutters interior grade commercial type core of black board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains or cross bands and face Veneers on both faces of shutters within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 19mm (nineteen millimetre) thick water proof termite resistant commercial board box including shelves and shutters top and back side of the cup board the cabinet shell be of 8mm (eight millimetre) thick water proof ply cut portion of the shelves shall be finished with 6mm (six millimetre) thick hard board and the shutters shall be finished with 1mm (one milllimetre) thick lamination of approved shade with nickel plated bright finished piano hinges and frame 25mm (twenty five millimetre) thick 2nd (second) class deodar wood complete (outer face of the cabinet should be measured for payment only) within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing M.S. Plain grills of required patterns in wooden frames with bolts and nuts or by screws complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 300x16mm (Three hundred into Sixteen milimetres) size Pilot/sheel anodized aluminium sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etcetra within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing aluminium Pilot/sheel anodized transparent or dyed to required colour and shade with necessary screws etcetraTower bolts (Barrel type) as approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

200x10mm (Two hundred into Ten milimetres) size

150x10mm (One hundred fifty into Ten milimetres) size

Providing and fixing aluminium Pilot/sheel anodized transparent or dyed to required colour and shade and of approved make with necessary screws etcetra handles with the necessary screws etcetra complete. within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

125mm (One hundred twenty five milimetres) size

100mm (One hundred milimetres) size

Providing and fixing aluminium oxidized Pilot/sheel 100mm (One hundred milimetres) size hook and eyes of complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (one hunded fifty millimetre) diametre oxidized M.S. double acting spring hinges oxidized transparent or dyed to required colour and shade with necessary screws within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (one hunded fifty millimetre) diametre oxidized M.S. hasps and staples with necessary screws within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing railing for stair case having baluster 40x40mm (forty into forty millimetre) square hollow Mild steel pipe (ISG-14) (Indian Standard Grade-14) guage with a clear height of 85cm (eighty five centimetre) and 60cm (Sixty centimetre) center to center jointing in steps and welded with electric gas at top alongwith hand rail of hollow Mild steel rectangular pipe 60x40mm (sixty into forty millimetre) (ISG-16) vertical balust welded or jointed with each other with two row of Mild steel flat 50x5mm (fifty into five millimetre) including applying a priming coat with steel primer and painting two or more coats with steel enamel paint other than white within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing 25mm (Twenty five milimetres) thick Kota Stone flooring 55x55cm (Fifty five into Fifty five centimetres) (Mirror polished) base of 20mm (twenty millimeter) thick cement mortar 1:4 (One cement: Four sand) laid over and jointed with Grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing moulding and nosing complete within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing 25mm (Twenty five milimetres) thick Kota stone flooring in risers of steps, skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete. within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying 20mm (twenty millimetre) thick acid proof tiles 30x30 cm (thirty into thirty centimetre) of specified shade in floors, treads of steps, landing laid on bed of 12mm (twelve millimetre) thick cement mortar 1:3 ( one cement isto three sand) jointing with cement slurry mixed with pigment to match the shades of tiles within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

White glazed tiles 6mm (six millimetre) thick in skirting rises of steps and 12mm (twelve millimetre) thick cement motor 1:3 (one cement isto three sand) and jointed with the cement slury within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted steel sheet ISI marked - Z 120 of tata / sail / reliance / jindal in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (Six milimetres) diametres with prepainted limpet and rubber washers complete with all accessories as required within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with 0.60cm (Zero decimal Sixty centimetres) thick prepainted steel sheet ISI marked - Z 120 of approved make in ridges (Factory made) of sail / relience / Jindal shall be having proper Gola/Shape of steel sheet Tata/ Sakti with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing valleys 90 cm (ninety centimetres) over all over all with 0.60mm (Zero decimal Six zero milimetres) thick prepainted sheet ISI marked - Z 120 of sail / relience / Jindal roofing with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (five) micron primer coating, back coat of polyster of 5 (Five) microns including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 30cm (thirty centimeters) wide 25cm (twenty five centimeters) deep as per design and drawing 0.60mm (Zero decimal Six zero milimetres) thick plain G.I. sheet TATA / Shakti for gutter with iron brackets 40x3mm (Forty into Three milimetres) size bolts and nuts and washers etcetera including making necessary connections with rain water pipe and providing complete accesories within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing on wall face 100mm (One hundred milimetres) diametres P.V.C. rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre as per ISI finolex / Relience / vectus pipe confirming to IS code 13592 for rain water pipe fixed with approved adhesive including filling the joints complete within all leads, lifts of materials and other incidentals, and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing on wall face P.V.C. acessories for rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre as per ISI finolex / relience / vectus or its equivalent for rain water pipe fixed with approved adhesive including filling the joints complete within all leads, lifts of materials and other incidentals. and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

100mm (One hundred millimtres) diametres PVC Plain bend

100mm (One hundred millimtres) diametres PVC shoe

100mm (One hundred millimtres) diametres P Socket

Steel work welded in built up sections joists channels, angles, tees with connection plates or angles, cleat as in trusses, trussed purlins main and cross beams, hips jack rafters, purlins connected to common rafters and the like in building including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing standard steel frame single rebate manufactured from M.S .angle iron section of 45x45x5mm (forty five into forty five into five millimetre) and M.S. 65x5mm (sixty five into five millimetre) flat in combination welded together to make one frame including hinges, jamb, lock, jamb beeds, and if, required angle thrashold of mild steel angles 50x25mm (fifty into twenty millimetre) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel but hinges 2.5mm (two point five millimetre) thick with provision for locking arrangement and shock observers as specified and applying a coat of approved steel primer after pretreatment of the surfaces within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing angle iron cupboard frames manufactured from MS Angles iron section 25x25x5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb, lock jamb, beed and if required angle threshold of mild steel angle 25x25mm (twenty five into twenty five millimetre) welded or rigidly fixed by mechanically means, lugs with split end tails to each jamb i/c steel butt hinges 2.5mm (two decimal five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after pretreatment of the surface, within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing steel glazed windows and ventilators of standard rolled steel sections, joints mitered and welded with 16x3.15mm (Sixteen into Three decimal Fifteen milimetres) lugs 10cm (Ten centimetres) long embedded in cement concrete block 15x10x10cm (Fifteen into Ten into Ten centimetres) size of 1:3:6 (One cement : Three sand : Six graded stone aggregate 20mm (Twenty milimetres) nominal size) or with wooden plugs and screws or with fixing clips or with bolts and nuts as required and iron fitting, including providing and fixing of glass panes with glazing clips and metal sash putty and applying a coat of red lead paint including carriage of materials in all leads and lifts and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST and any other taxes imposed by the Government.

Fixed steel windows

Top hung windows

Providing and fixing double ISI marked No. IS-1003 steel shutter windows side hung 1 (One) glazed and other wire gauge) of standard rolled steel section jointing mitered and welded manufactured to relevant ISI standard specification with 16x3.15mm (Sixteen into Three decimal Fifteen milimetres) lugs 20cm (Twenty centimetres) long embedded in cement concrete block 15x10x10cm (Fifteen into Ten into Ten centimetres) size of 1:3:6 (One cement : Three sand : Six graded stone aggregate 20mm (Twenty milimetres nominal size)or with wooden/steel plugs and screws or rawl plugs screws or with fixed clips or with bolts and nuts as required iron fitting including providing and fixing of glass pans with special putty of glazed side of shutter and wire gauge of IS designation 85G (Eighty five-G) with metal beading on other side complete including priming coat of red lead paint within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST and any other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter enamel paint other than white within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with ready mixed paint brushing wood primer pink within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) on new wood and wood based surface with ready mixed paint other than white to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering and stoping within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) on new wood and wood based surface with enamel paint other than white to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering and stoping within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) including carriage of material, within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for interior plastering upto two floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:4 (One cement isto four sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for interior plastering upto two floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:3 (One cement isto three sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

6mm (Six milimetres) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights within all leads, lifts of materials and other incidentals as per approved approved specification, drawings and design. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing RCC work smooth finishing of the exposed surface with cement mortar 1:3 (one cement isto three sand) within all leads, lifts of materials and other incidentals as per approved approved specification, drawings and design. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Distempering (two coats) with oil bound washable distemper with Nerolac/ Asian paints of approved brand and manufacture and of required shade on ceiling/sloping roof surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primer within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

White washing with lime on undecorated ceiling and/or sloping roofs (two or more coats) surfaces to give an even shade including thoroughly brooming the surface to remove all dirt, dust mortar drops and other foreign matter within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Finishing wall with nerolac surakha ( two coats) plastic enterior/ apex emulsion paint of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign mater and also including preparing smootgh including applying of putty as required for making the surface complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 4mm (four millimetre) thick plain A.C. sheet lining to the butt jointing and wooden screws (frame work and cover fillet to be paid for separately) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing plinth protection 50mm (Fifty milimetres) thick cement concrete 1:3:6 (One cement: Three sand: Six graded crushed stone aggregate 20mm (Twenty milimetres) nominal size) including finishing the top surfaces of concrete smooth within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing under layer for plinth protection of 75mm (Seventy five milimetres) thick(un-consolidated)bed of dry brick/stone aggregate 40mm (Forty milimertres) nominal sizes well rammed and consolidated and grouted with fine sand including preparation of ground within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Constructing 15x23 cm (fifteen into twenty three centimetre) U-shape open surface drains with square rubble stone masonry wall in cement mortar 1:6 (one cement isto six) and inside plastering with cement mortar 1:3 (one cement isto three sand) including earth work and laying 10 (ten) centimeter (Ten centimeters) cement concrete bed in 1:5:10 ( one cement isto five sand isto ten graded stone aggregate of 40mm (forty millimetre) size and 75mm (seventy five millimetre) cement concrete 1:2:4 (one cement isto two sand isto four graded stone aggregate) 20mm (twenty millimetre) nominal size at bottom joint of drain and finished with a floating coat of neat cement complete as per standard design, The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

WATER SUPPLY & SANITARY INSTALLATION

Providing and fixing polythelene aluminum polythelene (PE- AL-PE) composite pressure pipe U.V. stabilized with carbon block confirming to I.S. 1545-2004 of Kitec or its equivalent for water supply including clamps at appropriate spacing, cutting fixing and making good the walls etcetera; but excluding the cost of fittings (Internal work), including filling the joints with approved adhesive complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

1216 (16mm) sixteen millimeter diameter pipe O.D. pipe

1620 (20mm) twenty millimeter diameter pipe O.D. pipe

Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40nmm (Twenty milimetres to Forty milimetres)nominal bore by providing and fixing tees including cutting and threading the pipe complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 650 x 450 x 250 mm (six hundred fifty into four hundred fifty into one hundred fifty millimeter) size vitreous china laboratory sink with C.I. or M.S steel brackets painted white including cutting holes in walls and making good the same including the cost of fitting and entire carriage of materials, within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing C.P. Brass Chain 50cm (fifty centimetre) Iong and rubber plug for lead waste pipe within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres C.P brass waste for wash basin and sink of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal waste for wash basin or sink complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 32mm (Thirty two millimetres) nominal size diametres rubber plug for wash basin within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres M.I. union for wash basin or sink.complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetres) diametres C.P. Grating Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal for gully floor or Nahni trap within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diametre nominal bore chromium plated ISI marked fancy bib tap of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diametre C.P. stop cocks of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Constructing brick masonry chamber for under ground C.I. inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5(One cement: Five sand) C.I. cover with frame(light duty) 455x610mm(Four hundred fifty five into Six hundred ten milimetres)internal dimensions total weight cover and frame to be not less than 38Kgs (Thirty eight Kilograms) weight of cover 23 Kgs (twenty three kilograms)and weight of frame 15 Kgs (Fifteen kilograms) RCC top slab with 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres nominal size) foundation concrete 1:5:10 (One cement: Fiver sand: Ten graded crushed/broken stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm ( Fifteen milimetres) thick with cement mortar 1:3 ( One Cement: three sand) finished with a floating coat of neat cement on walls and bed concrete etcetra complete inside dimensions 455x610mmx450mm (Four hundred fifty five into Six hundred ten into Four hundred fifty milimetres) deep within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing stone ware gully trap grade "A" complete with Carating brick masonary chamber in cement mortor 1:5 (1cemenr isto five sand)C.I cover with Frame 300x300 mm (three hundred into three hundred millimetre) size weight of coer to be not less than 4.53 kg (four decimal five three kilogramme) and frame 2.72 kg (two decimal seven two kilogramme) square mouth trap 150 x 100mm (one hundred fifty into one hundred millimetre) size P or R within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetres) diametres PVC holder bat clamps of approved design to P.V.C. rain water pipe embedded in and including cement concrete blocks 10x10x20cm of 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and cost of cutting holes and making good the walls etc; within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 110 x 90mm (One hundred ten into Ninety milimetres) P.V.C. I.S.I. marked floor trap ISI marked (conforming to BIS-14735-99) of self cleaning design including with approved adhesive cost of cutting and making good walls and floors complete, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and placing water tank make P.V.C. SINTEX having capacity of 500 (Five hundred) liters each tank with necessary fittings including over flow pipe scour pipe etcetera and pads required for in let and out let ball valve with cover and locking arrangements complete in all respect including carriage of material, within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetres) diametres P.V.C. Collar ISI marked including fixing with approved adhesive complete, including carriage of material, within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetres) diametres P.V.C. Tee ISI marked including fixing with approved adhesive complete, including carriage of material, within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (one Cement isto four Sand isto eight graded stone aggregate 40mm (forty millimetre) nominal size bedding 100mm (one hundred fifty millimetre) for PVC pipes of the following internal diameters, necessary form work and curing complete within all leads, lifts of materials and other incidentals, as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providin, and fixing 200mm vide cast iron rungs with chequre eibbed on slip surface including fixing in manhole with 200 x 200 x 100 mm cement concrete 1:3:6 (1 cement :3 sand: 6 graded/crushed stone aggregate 20mm nominal size) mixed and vibrated mechanically and curing complete excluding the cost of form wor, as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing if medium duty 500 mm dia meter cover with weight 116.00 kg.as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying in trenches 5cm dia asbestos cement pressure pipe class-5 (Earth work in trenches and jointing of pipe to be measured and paid for separately.).as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing C.I. Detachable joints to asbestos cement pressure pipe and plain ended C.I. Specials with collar rubber ring flags and nuts complete i/c testing of joints 250 mm nominal size.as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing grill jail penal on chamberas directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Apratim Ashesh Mahajan