NIT No GE/ND-59/2025-26

Amount

Excavation in trenches not exc 1.5 mtr wide & not exc 1.5 mtr in depth for foundation etc and getting out in hard/dense soil complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr wide & not exc 1.5 mtr in depth for foundation etc and getting out in Soft/disintegrated rock complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr wide & not exc 1.5 mtr in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed. Note: Excavation any type of soil soft/ Hard/ Disintegrated/ Rock carried out by only manually without any damages, and no extra cost paid by MES/Govt for repaires of damages any type of existing services

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete of grade M25 design mix (using 20 mm graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete of grade M25 design mix (using 20 mm graded stone aggregate) in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete of grade M25 design mix (using 20 mm graded stone aggregate) in top beams, cantilevers, bressummers, lintels over 1.5m span complete all as specefied and directed.

Use & Waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces complete all as specified and directed.

Use & Waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of Square, rectangular or polygonal Rough finished complete all as specified and directed.

Use & Waste of formwork to sides and soffits of top beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc of rough finished surfaces of concrete all as specefied and directed.

M&L for TMT bars 10 mm dia and over, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for TMT bars 5 mm dia and over upto and including 10 mm dia, as in stirrups, spacers and binders, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for brick work with fly ash bricks, using old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:4 on external wall finished even and fair complete all as specefied and directed.

S&F posts and struts/grills or 'Y' section in fencing including cutting tops to shape as directed drilling holes, notching for wire, etc, flat iron fillits (for securing wire mesh etc,) including all necessary drilling, bolting or riviting, etc and similar work confirming to Fe-290 Gde -E-165 complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specefied and directed.

Retuning filling any type of soi/disintegrated rock, including spreading, leveling, watering and well ramming in layers not exc 25 cm each layers complete all as specified and directed. Note -Retuning filling carried out by only manually without any damages, and no extra cost paid by MES/Govt for repaires of damages any type of existing services

Removing excavated soil material not exc 50 Mtr & depositing where directed at a level not exc 1.5 Mtr above the starting point complete all as specified and directed.

M&L for 18/20mm thick pre-formed bituminous filler board filled in two layers as in crumple joints as in wall complete all as specified and directed. Note : Each layer of 18/20mm thick shall be measured separately.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces included preparation of new plaser surface complete all as specified and directed by Engg in charge.

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drill for fixing of steel sheeting or other covering etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting and also fastening and fixing complete all as specified and directed.

M&L for 16-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, wall, floor and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick scred bed/plater as backing coat of CM 1:4 complete all as specefied and directed.

M&L for concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in path, hardstanding laid in panels with and including use and waste of form work and to divide the area in panels and finishing the surface fair and even complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete PU coating and glossy finished paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in cover slab etc including necessary form work, set in cement mortar 1:4 complete all as specified and directed. Note: TMT Bar shall be measured and paid sepertely

Demolition of cement concrete unreinforced of any description and in any position not other wise specifically provided as in drain copings and similar situations incl removing the unserviceable material out side the MOD land complete all as specified and directed.

Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars, drains, culverts and walls etc but excluding ashlar facings, dressed stone work and pre cast concrete articles, built in cement mortar incl removing the unserviceable material out side the MOD land complete all as specified and directed.

M&L for brick work with sub class 'B' bricks , using old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per item No 28.00 above but except bricks complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels, drains including all necessary form work complete all as specified and directed.

M&L for extra forming fair finished drain on channel 30 m inner girth in cemenjt concrete using extra cement including forms, moulds mitered/ stopped ends etc complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed. Note : For adjustment of rate only against item No 31.00 here-in-before

M&L for rendering 10 mm thick ready mix plaster fair faces of brick work or concrete surfaces to be finished even and smooth using extra cement mixed with integral water proofing compound incl WPC @ 200ml per 50 kg of cement or in the manner specified by the manufacturer and in the proportions indicated complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in coping including weathering, slightly rounded or chamfered angles and throating, as directed and necessary form work complete all as specified and directed by Engg in charge.

S&F 2mm thick reinforced fiber sheet for walling as per direction of engr in charge including taking down complete all as specified and directed.

M&L for steel work as in hand rails, wind ties for roof including securing bolts, posts and struts in fencing including cutting top to shape as directed drilling holes, notching for wire etc flat iron fillets for securing wire mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description and any positions not other wise provided for complete all as specified and directed. Note: (a) Srl Item No 04.00 to 07.00, 11.00 to 16.00, 20.00 to 24.00, 28.00, 35.00 & 36.00 of BOQ are major items for the subject tender and material in respect of these items shall be procured within one month after placing of work order and produced before Engg in Charge alongwith original purchase vouchers as per direction of Garrison Engineer and shall obtain a certificate from Engg in charge that material in respect of above mentioned items have been submitted in the office of Engg in charge in their safe custody. (b) Materials in respect of Freakishly low declared items if any at the time of acceptance of contract shall be procured within one month after placing of work order and submit the same in the office of Engg in charge alongwith original purchase vouchers in their safe custody and shall obtain a certificate from Engg in charge.

M/S MSD & Associate (BID ID -3411687)

ATHARV CONSTRUCTION (BID ID -3418051)