SPECIAL REPAIR TO CERTAIN EM INSTALLATION UNDER GE AF TECH AREA AT AF STN AGRA

Amount

Demolition of Asbestos cement sheeting (corrugated /semi corrugated)/fibre sheet in roof covering including ridge etc complete all as specified & directed.

S&F Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self taping screws/J hook etc complete all as specified & directed.

S&F Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in ridge of roof covering/cladding to wall,fixed with self taping screws/J hook etc complete all as specified & directed..

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc complete all as specified & directed by Engr-in-charge.

Demolition of cement Concrete in ground floors and pavings exc 15 cm thickness (below or above ground level) etc complete all as specified & directed by Engr-in-charge.

Demolition floor,hearth or wall tiling including cement mortar bedding/backing and rubbish off the premises etc complete all as specified & directed by Engr-in-charge.

M&L for light shade vitrified ceramic tiles, joint free (edge cut) coloured , 9 to 10mm thick (square/ rectangular) polished, area of each tile n.exc 0.36 sqm, in floors etc laid over with and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles etc complete all as specified & directed

M&L for Non skid, joint free (edgecut) coloured ceremic tiles 7 to 8 mm thick (Square / rectanguler) polished area of each tile exceeding 0.11 sqm but not exeeding 0.18 sqm as in floors etc laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles etc complete all as specified & directed by Engr-in-charge.

M&L for glazed ceramic coloured tiles of size 400x350mmx7mm thick on wall/vertical surfaces such as skirting, dados and riser to steps etc including laid over 10mm thick screed bed in CM 1:4 fixing on wall/vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified & directed by Engr-in-charge.

M&L for Cement concrete type D-2 1:4:8 (40mm graded aggregate) in foundations, filling and mass concrete etc complete all as specified & directed by Engr-in-charge.

M&L for Sand filling under interlocking tiles or in foundations including watering and consolidation etc complete all as specified & directed by Engr-in-charge.

M&L for rubber moulded Machine pressed precast conctete interlocking paver block with grey cement and coloured pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade etc complete all as specified and as directed.

M&L for 75mm thick plain cement concrete type C-2 1:3:6 (using 40mm graded stone aggregate) in sub base to floors and paving etc all complete all as directed by Engr-in-charge

M&L for Chequered cement concrete tiles 25mm thick with mixture of white cement in equal proportion and pigment, area of each tile exceeding 0.05 sqm but not exceeding 0.09 sqm, jointed and pointed in neat cement slurry in floors,laid on and including screed bed or bedding layer of cement mortar 15mm thick in CM 1:6 etc complete all as specified & directed

M&L for machine cut kota stone flooring 20-25 mm thick over screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 20 mm thick screed bed or bedding layer in cement mortar 1:6 including proper rubbing & polihing etc complete all as specified and as directed by Engineer-in-Charge.

Demolition mild steel or wrought iron work in roof trusses,gratings etc and similar work etc complete all as specified & directed.

S&F mild steel framed work such as grills gratings etc with ends of bars shouldered, riveted or forged into spikes,framed guard bars, barred iron doors, ladders, framed blasters, walkways, railings, framework of water tanks and similar work conforming to Fe 290 Grade E-165 complete all as specified & directed.

M&L for mild steel work in roof trusses,purlins,rafters,wind ties,crane gantries,rails and fastenings and heavy bracket framing (Beam,Tee,Angle,Channel or Flat sections) including distance pieces,cleats etc complete all as specified and directed.

Cutting out the vegetation like shrubs, plants and bushes of any description upto 1.5m width and taking out roots from the wall or roofs etc complete all as specified & directed by Engr-in-charge.

Demolition of brick work masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlars facing,dressed stone work and pre-cast concrete articles etc complete all as specified & directed by Engr-in-charge

M&L brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar (1:6) etc complete all as specified & directed by Engr-in-charge

Taking down cement / lime plaster of any description on brick work or stone walls etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed

M&L for rendering 10 mm thick on brick or concrete surface of walls in cement mortar 1:6 finished even & smooth without extra cement on internal wall surfaces etc complete all as specified & directed.

M&L for rendering 15 mm thick on brick or concrete surface of walls in cement mortar 1:4 finished even & smooth without extra cement including mixed with water proofing compound as per manufacturer instruction on external wall surfaces etc complete all as specified & directed. Note:- WPC will be measured & Paid separately

M&L for preparation of newly plastered surfaces of wall and applying two coat of distemper oil emulsion over a coat of primer etc complete all as specified and directed

M&L for preparation of old plastered surfaces of walls and applying one coat of distemper oil emulsion white or tinted, including repair of holes and cracks etc complete all as specified and directed

M&L for preparation of new plastered wall surfaces and Finishing walls surfaces by applying Acrylic Smooth exterior paint of required shade : New work (Two coat @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) in normal / camouflage pattern as per manufacturers instructions etc complete all as specified and directed by Engr-in-charge.

M&L for preparation of old decorated surfaces of wall after complete removal of existing treatment and applying two coats of weather proof exterior emulsion paint over a coat of primer complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling by complete removal of existing treatment of plastered or un-plastered surfaces and applying two coats of white wash etc complete all as specified and directed.

M&L for preparation of old wooden surfaces and applying two coat of synthetic enamel paint etc complete all as specified & as directed.

M&L for preparation of new surfaces of steel exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of zinc red oxide primer etc complete all as specified and as directed by Engineer-In-Charge.

Taking down existing rolling shutter of any type, width and height not exceeding 3.5 mtr in any position etc complete all as specified & as directed by Engr-in-charge.

M & L for 1.25mm thick steel rolling shutter upto height 3.5m, without ball bearing but including guide channel, top hood covers anchoring rod, hasp and staple and other necessary, accessories required to function the shutter and applying two coats of synthetic enamel paints erected in position etc complete all as specified and directed by Engr-in-charge.

Taking down chowkats with shutters of any description (without taking off shutters from the frame) removing from site n exc. 1.5 sqm each etc complete all as specified & directed. by Engineer-In-Charge.

Taking down chowkhats or frames with shutters exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutters from the frame) etc complete all as specified & directed.

S&F factory made 30 mm thick flush shutter solid core construction with block board core and plywood face panels commercial type on both sides, including 5mm thick teakwood leaping alround etc complete all as specified and as directed

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing shown in section 8 of SSR part II complete all as specified & directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supply & fix in opening as per specification etc complete all as specified & directed.

S&F 300mm long stainless steel finished sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple etc complete all as specified and as directed

S&F stainless steel finished butt hinges cold rolled medium weight of size 100mm complete all as specified and as directed.

S&F 150 mm long stainless steel finished barrel tower bolt of extruded section complete all as specified and as directed

S&F 150 mm long stainless steel finished handle fabricated type complete all as specified and as directed

M&L for 5 mm thick sheet glass ordinary quality and glazing with oil putty in square n-exc 0.5 sqm in each pane complete all as specified & directed.

S&F aluminium (Die cast) body, door closer hydraulically regulated designation No-1, universal type, suitable for door shutters of weight not more than 35 kg complete all as specified and directed.

M&L for preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a one coat of pink primer complete all as specified & as directed.

Supply and fix in repair white vitreous china squatting pan ‘ORISSA’ pattern of size 580 mm x 450 mm white with integral foot rests with ‘P’ or ‘S’ trap, front or back inlet including all connection and provision of lime concrete base complete all as specified and as directed..

S&F in repair vitreous china wash down water closet pan (padestal pattern) with seat cover (excluding fixing bolts, flushing cistern and flush pipe) etc complete all as specified and as directed.

S&F in repair flushing cistern 10Ltr capacity PVC valveless, syphonic action type, low level, white, with inlet, ball valve, float and handle including brackets etc complete all as specified & directed.

S&F in repair for Wash basins, Vitreous China (flat back or angle back type) size 580X450mm, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe , complete all as specified and directed.

S&F in repair 15 mm dia bib tap cast copper alloy, fancy type chromium plated ,'with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule etc complete all as specified & directed.

S&F in repair fancy type 15 mm dia Pillar taps ,cast copper alloy ,with capstan heads chromium plated screwed down high pressure, with or without letterd HOT or COLD with long screwed shanks and fly nuts ,screwed for iron pipe and fixed etc complete all as specified & directed..

S&F in repair brass chromium plated stop valve/ Angle valve 15 mm fancy type with long shank and cup (concealed type) fixed etc complete all as specified & directed..

S&F in repair soap dish tray embedded in wall , vitreous china white, approximate size 160x160x90 mm complete all as specified & directed.

S&F for PVC connection 15mm size with brass nuts of length 450mm complete all as specified & directed.

S&F in repair towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190 gms) ccomplete all as specified & directed.

S&F cast iron floor trap 100 mm dia of outlet, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) using 20 mm graded stone aggregate etc complete all as specified & directed.

S&F in repair PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints, fixed on walls or floors complete all as specified and as directed

S&F in repair PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints, fixed on walls or floors complete all as specified and as directed

S&F PVC (SWR) plain bend 110 mm dia, of any redius with rubber ring joints, complete all as specified and as directed

S&F PVC (SWR) plain bend 75 mm dia, of any redius with rubber ring joints, complete all as specified and as directed

Taking up or down 15 mm bore steel tubing and connections, complete all as specified and as directed

Taking up or down 20 mm bore steel tubing and connections, complete all as specified and as directed by Engr-in-charge.

Supply and fix 15 mm bore galvanized steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line etc complete all as specified & directed. by Engineer-in-Charge.

Supply and fix 20 mm bore galvanized steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line etc complete all as specified & directed. by Engineer-in-Charge.

Demolition PVC water tanks of capacity exc 500 ltrs but n. exc 1000 ltrs complete all as specified and as directed by Engr-in-charge.

M&L for rotational moulded polyethylene water storage tank 1000 ltrs capacity double layered cylindrical vertical with closed top hoisted and fixed in position including fittings etc complete all as specified & directed. by Engr-in-charge.

Demolition of existing roof treatment of any type description incuding tarfelt/cement plaster etc from roof surfaces including cleaning the surface and removing the debris etc complete all as specified & directed.

M & L for Cutting out cracks to V-section in existing roofs or terracing, cleaning grouting with cement and sand mortar 1:3 complete all as specified & directed.

M & L for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 all as specified and as directed.

M&L for cement concrete 1:2:4 type B1 (using 20mm graded stone aggegate) (average 50 mm thickness) as in levelling course / padding over roof complete all as spd and directed.

M&L for rendering or bedding layer 15mm thick in cement mortar 1:4 on concrete surfaces of roof with WPC, finished even and fair with out using extra cement complete all as specified and directed. (WPC shall be measured & paid seperately.

Supply only water proofing compound.

M&L for cleaning surfaces and applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg/Sqm including cleaning surface complete all as specified & directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified complete all as specified and as directed.

M&L Cement concrete tiles 30cm x 30cm x 20mm thick, machine pressed; laid over and including 20 mm thick screed beding in cement mortar (1:4) , set jointed and pointed in neat cement slurry in floors, and cut and polished etc complete all as specified and as directed.

Taking down carefully Aluminium/copper point wiring batten type/casing capping/concealed type any descreption (Light/ Fan/Socket or power) complete incl fitting, fixture such as switches, sockets, ceiling rose, brackets, holders, bulk head fitting etc and making good disturbed surface of wall/ceiling etc complete all as specified and directed.

Taking down main switch/MCB DB/AC enclosure/Three phase enclosure by disconnecting the electric supply etc complete all as specified and directed.

Taking down old XLPE cable of any size up to 16 Sqmm from wall/ceiling/truss/duct by disconnecting the electrical connection and descrewing the saddle clips/clamps and keeping aside to reuse the same after ceiling work etc complete all as specified and directed.

M&L for point wiring with stranded copper conductor of 1.5 Sqmm size (Nominal area) PVC insulated unsheathed cable FRLS in and including concealed PVC conduit ISI marked medium grade not less than 20mm dia with all accessories such as TEE, bend,elbow,reducers,sockets and junction boxes etc, concealed sunk in pressed steel terminal boxes of reqd size of thickness 1.6 mm factory made and painted with stove enameled black paint and bituminous coat of external portion to prevent the rust with top cover 3mm thick plastic laminated sheet of required colour fixed with brass screws and cup washer including 1.5 sqmm stranded copper conductor PVC insulated cable of green colour as earth continuity connected to common earth dolly and all sunk/terminal boxes fitting/fixture, all cable ends will be terminated with suiable brass thimbles to prevent the heating of termination point complete for One light/fan/exhaust fan point controlled by one way 5 Amp switch.with all accessories all as specified and directed: - Note : Conduiting on the wall shall be concealed but if it is not posible to conceal the conduit on the RCC roof /crossing of column/beam then it shall be fixed on surface as per the condition of site.

All as per Ser Item No 81 above but One 3 pin/5 pin socket out let 5 Amp on independent board with independent circuit from DB box.

All as per Ser Item No 81 above but OneOne 3 pin/5 pin socket out let 5 Amp same board

All as per srl item No. 81 above but for 3/5 pin socket outlet for 15 Amps on independent board with independent circuit drawn from DB box with 2.5 sqmm PVC insulated, unsheathed single core multistranded copper conductor cable 1100 volts grade including 2.50 sqmm PVC insulated unsheathed solid copper conductor cable as earth continuity conductor complete all as specified & directed.

S&F of switch piano, flush type 5 Amp single pole one way.

S&/F of switch piano, flush type 15 Amp .

S&F of socket out let, flush type 5 pin 5 Amp.

S&/F socket outlet multi purpose 3 pin 15 Amp and 3 pin 5 Amp, flush type.

S&F ceiling rose surface bakelite ISI Marked three terminal.

Supply and Fixing the lamp holder of PVC/polycarbonate angular/batten type with back plate fancy type with three terminals isolated body etc complete all as specified and directed.

S&F stepped type Electronic fan regulator flush mounted socket type complete all as specified and directed.

S&F in renewal of heavy duty exhaust fan steel body AC single phase 230 volts ,50 Hz of size 300mm sweep , 900 RPM with blades, fixed with frame and louvers including cutting the existing wall of adequate size in round shape , making good the disturbed surface with cement mortor and grouting the louvers and nut bolts of exhaust fan etc complete all as spacified and directed.

Supply and Fixing in renewal of the LED tube light fitting 1x20 Watt , AC decorative box type with driver , holder including LED tube light connecting up with three core flexible copper conductor of suitable size from ceiling rose to fittingand etc complete all as specified and directed.

S&F in renewal of LED light fitting mirror type with high output diffuser 2feet, 10 watt AC 230V with driver , holder and LED lamp including connecting up with driver three core flexible copper conductor of suitable size from ceiling rose to fitting etc complete all as specified and directed.

Taking down ceiling fan for painting including painting of ceiling fans with synthetic enamel paint by spraying including filling cavities with filler, after cleaning all dust and regreasing, oiling and safety clips complete with all fitting Refixing to its original porsition by connecting up fan with three core flexible copper conductor of suitable size from ceiling rose to fan etc complete all as specified and directed.

S&F in repair MCB DB of sheet metal enclosure double door type, single pole and neutral 12 way with 200 Amp rated bus bar 240V and grouted in walls with PCC 1:2:4 type B1 using 20mm graded stone aggregate etc complete all as specified and directed.

S&F in repair MCB DB of sheet metal enclosure double door type, single pole and neutral 8 way with 200 Amp rated bus bar 240V and grouted in walls with PCC 1:2:4 type B1 using 20mm graded stone aggregate etc complete all as specified and directed.

S&F in repair MCB DB of sheet metal enclosure double door type, single pole and neutral 4 way with 200 Amp rated bus bar 240V and grouted in walls with PCC 1:2:4 type B1 using 20mm graded stone aggregate etc complete all as specified and directed.

S & fix in repair MCB SP 6 to 32 Amps, 240V 'C' Series 10 KA etc complete all as specified and directed

S & fix in repair MCB DP 40 to 63 Amp 240 Volts 'C' series 10 KA etc complete all as specified and directed.

Supply and fix in renewal of LED street light 45 Watt IP 66, New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with 10KV Built-in Surge Protection Device including GI bracket made by 40mm GI pipe light grade bent to shape of length 1.5 mtrs and fixed with MS clamps GI nut bolts and grouted clamps on wall and complete all as specified and directed.

S&F in replacement sub main wiring drawing in and including concealed PVC conduit not less than 25mm dia medium grade with PVC cable 04 Sqmm nominal area 2run single core PVC insulated unsheathed cable with stranded copper conductor including 04 Sqmm size PVC cable stranded copper conducter as earth continuity wire and connected to earth dolly with proper crimping of thimbles bottle type etc complete all as specified and directed.

S&F in replacement sub main wiring drawing in and including concealed PVC conduit not less than 25mm dia medium grade with PVC cable 06 Sqmm nominal area 2run single core PVC insulated unsheathed cable with stranded copper conductor including 06 Sqmm size PVC cable stranded copper conducter as earth continuity wire and connected to earth dolly with proper crimping of thimbles bottle type etc complete all as specified and directed.

S&F in replacement sub main wiring drawing in and including concealed PVC conduit not less than 32mm dia medium grade with PVC cable 10 Sqmm nominal area 4run single core PVC insulated unsheathed cable with one run of multi stranded copper conductor including 10 Sqmm size PVC cable of stranded copper conducter as earth continuity wire and connected to earth dolly with proper crimping of thimbles bottle type etc complete all as specified and directed.

S&F in replacement sub main wiring drawing in and including concealed PVC conduit not less than 25mm dia medium grade with PVC cable 10 Sqmm nominal area 2run single core PVC insulated unsheathed cable with stranded copper conductor including 10 Sqmm size PVC cable stranded copper conducter as earth continuity wire and connected to earth dolly with proper crimping of thimbles bottle type etc complete all as specified and directed.

S&F in renewal sheet metal enclosures with socket plug top and MCB single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20Amp MCB ,240 volts etc complete all as specified and as directed by the Engineer in charge

S&F in renewal VTPN DB,4 way Vertical type,440V,3 phase with rated busbar 250 Amps, double door type , IP-54 protection and mechanical strength IK 09 ,isolated neutral busbar suitable for accomodate MCCB 3/4 pole 415 volts rating upto 250 Amp as a incomer and MCBs as out going , including grouting in wall in PCC 1:2:4 type B1 etc complete all as specified and directed.

S & fix in renewal MCCB DPX 160 thermal magnetic of 63 Amps 3 pole 16 KA, 415 Volts 50 Hz complete including connecting all incoming and outgoing connection by means of suitable size of lugs/thimbles etc complete all as specified and directed.

Supply and Lay in repair XLPE insulated LT UG cable PVCsheathed , bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor 16 Sqmm 2 core laid in trenches or fixed on wall/floor/poles etc complete all as specified and directed.

Supply and Lay in repair XLPE insulated LT UG cable PVCsheathed , bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor 16 Sqmm 4 core laid in trenches or fixed on wall/floor/poles etc complete all as specified and directed.

Excacation in trenches in soft/hard soil n. exc 1.5 m wide and n. exc. 1.5 m in depth for laying cables and getting out etc complete all as specified and directed

Return filling in including spreading, leveling, watering and well ramming in layers n. exc. 25cm thick in hard/dense soil after cable are laid and tested etc complete all as specified and directed.

Removing excavated surplus soil to a distance n. exc. 50m and deposited where directed at a level n. exc.1.5m above the starting point etc complete all as specified and directed.

M&L for sand filing with clean dry fine sand unsashed including gently punning around cables in trenches for cable protection etc complete all specified and directed. Note : punned thickness shall be measused and paid.

Supply & Laying sub class 'B' briks old size with axis of the bricks perpendicular to the axis of the cable as in cable protection etc complete all as specified and directed.

M&L in repair 40 mm dia GI tubing light grade with all fittings such as tee, bend,elbow,reducer, socket etc to insert under road/on or fixed pole/wall for LT UG cable protection etc complete all as specified and directed.

M&L for Cutting the road / hard standings or excavating in trenches not exceding 0.40 mtr wide and not exc 0.80 mtr deep across the road for laying cable including making good the excavated portion by means of PCC 1:2:4, type B1 using 20mm graded stone aggregate etc to matching with the surroundings etc complete all as specified and directed.

M&L in repair 50 mm dia GI tubing light grade with all fittings such as tee, bend,elbow,reducer, socket etc to insert under road/ or fixed on pole/wall to LT UG cable protection etc complete all as specified and directed.

M&L for earthing in renewal of complete with galvanised steel plate electrode 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron wire of size 4 mm by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified including excavation and earth work in any type of soil and disposal of surplus soil to a distance nexc 50m including 40 mm GI tubing light grade and necessary fitting for protection of earthing lead including laying of charcoal dust and common salt Earth pit shall be constructed in PCC (1:2:4) type B-1 using 20mm graded stone aggregate with 40x40x6mm MS angle iron frame including RCC cover 40mm thick in CC (1:2:4) type B-0 using 12.5mm graded stone aggregate reinforced with 6 mm dia round bar @ 75mm C/C both ways with MS handle 12mm dia, plastering 15mm thick in CM (1:6) internally and upto 150mm below ground level externally, PGI funnel with mesh and 20mm dia medium grade GI pipe for watering etc complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test including testing on completion etc complete all as specified an directed.

Abhi Construction (BID ID -3106962)

Sethi Brothers (BID ID -3104307)

M/s M S Sharma and Co. (BID ID -3111525)

C P Singh and Co (BID ID -3110960)

M/S SINGH ELECTRIC CO (BID ID -3110056)