CERTAIN REVENEW AND MINOR WORKS AT CABS GTRE AND CEMILAC BANGALORE

Amount

Demolishing brick work manually/ by mechanical means in cement mortar , including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.

Providing and laying in position Plain Cement Concrete 1:2:4 (1 cement: 2 course aggregate (Zone III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources) excluding the cost of centering and shuttering for all work upto plinth level all as specified and directed

Providing and fixing powder coated (minimum thickness of powder coating 50 micron) aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : for fixed portion all as specified and directed

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board ,Pre-laminated particle board with decorative lamination on both sidesconforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in- charge

M & L , Plastering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 all as specified and as directed

M & L for preparation of plastered or unplastered surface & Distempering 02 coats with oil bound washable distemper of approved brand and manufacture to give an even shade over and including water thinnable priming coat with cement primer all as specified and directed by EIC.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4 mm thickness (weight not less than 10.00 kg/sqm)

Providing and fixing 4mm thick float glass panes of 5.5 mm thickness (weight not less than 10kg/sqm) glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) & as directed by EIC.

Dismantling tiles of thickness 10 mm to 25 mm, in wall, roofs and floors laid in cement mortar including stacking material within 50 metres lead all as specified and as directed

M&L for non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes 1:4 cement mortar etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed

Providing and fixing 1st quality Coloured glazed ceramic tiles of size 450mm x 300mm / 450mm x 350mm , in dado/skirting etc. conforming to IS : 15622 of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete all as specified and directed.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-Charge.

Providing and fixing false ceiling at all heights with 15mm thick integral densified micro edge light weight calcium silicate reinforced with fibre and natural filler false ceiling tiles of size 595 x 595mm of approved texture, design and patterns having NRC (Noice Reduction Coefficient) of 0.50 (minimum) as per IS 8225 : 1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476(part 6&7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Gird of hot dipped galvanised iron section of 0.40mm thick on Silhouette profile, rotary stiched double webbed white with 6mm reveal profile (white / black), comprising of main-T runners of size 15x42mm of length 3200mm, cross - T of size 15x42mm of length 1200mm and secondary intermediate cross - T of size 15x42mm of length 600mm to form grid module of size 600x600mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fastener, 6mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 22x19x0.40mm of length 3000mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead all as specified and as directed

M&L 10 mm thick internal plaster in CM 1:6 on other than fair faces of walls , finishing the surfaces even and smooth w/o using extra cement all as specified and as directed

All as per item no.16 above but on old surfaces after and including complete removal of existing treatment of any type and condition complete all as directed by EIC

Taking down /dismantling of RWP pipes with fittings of 150mm dia in any position as in soil/waste pipes all as specified and as directed

Supply and fix 110 mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls,floors, or in trenches all as specified and as directed

Supply and fix 75 mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls,floors or in trenches all as specified and as directed

Supply and fix PVC (SWR) bends any radius 75 mm dia of bore all as specified and as directed

Supply and fix PVC (SWR) bends any radius 110 mm dia of bore all as specified and as directed

Supply and fix PVC (SWR) floor trap 75 mm dia out let with grating plain including jointing with solvant cement all as specified and as directed

Supply and fix PVC (SWR) gully trap 125/110mm with Grating, setting and jointing with solvant cement all as specified and as directed

Providing and fixing vitreous China wash basin of size 550x400mm with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require all as specified and as directed

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm all as specified and as directed

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore in repairs all as specified and as directed

Providing and fixing C.P. brass stop cock (concealed) in repairs of standard design and of approved make conforming to IS:8931 15 mm nominal bore all as specified and as directed

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms all as specified and as directed

Providing and fixing Stainless steel towel rail complete with brackets fixed to wall with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms all as specified and as directed

Dismantling 15 to 40 mm dia G.I./PVC pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes .size of 25 mm internal dia.(concealed on wall),having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

All as per item no.32 above but of size of 40 mm internal dia.(Exposed on wall) all as specified and as directed

Providing and placing on terrace (at all floor levels) polyethylene water storage tank 500L, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank, including removal of old one all as specified and as directed

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 15 mm nominal bore all as specified and as directed

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid all as specified and as directed

Supply and fix in repairs health faucet(ABS BODY) mild steel chromium plated suitable for 15mm dia pipe with 1.25metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

Dismantling doors, windows and clerestory windows (steel or wood)shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area 3 sq. metres and below all as specified and as directed

Providing and fixing factory made single extruded WPC 30 mm thick (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

Providing and fixing factory made single extruded WPC Frame size 45 x 70 mm(Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threadedstar headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

Supply only Anodised Aluminium butt hinges 100x63x4mm all as specified and as directed

Providing and fixing aluminium tower bolts, 150mmx10mm dia ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete all as specified and as directed

Providing and fixing 125mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete all as specified and as directed

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete size 250x16 mm all as specified and as directed

Excavating holes in all kind of soils more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m. all as specified and as directed

Earth work in surface excavation for all kind of soil not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: all as specified and as directed

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) all as specified and directed

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete all as specified and directed

Providing and fixing up to floor five level precast cement concrete solid block 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources), including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete all as specified and directed

Providing 15 mm cement plaster in fine sand on the rough side of single or half brick wall or concrete surface of mix 1:6 (1 cement: 6 fine sand) all as specified and directed

M&L for 18-20 mm thick Granite stone slab colour black, Cherry/Ruby red gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, steps, floor etc and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels all as specified and directed

Providing and laying chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with dark shade pigment using ordinary cement to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). all complete as per the direction of Engineer-in-charge.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping all as specified and directed

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed

S&F steel work for hot finished seamless type tubes in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete all as specified and directed

Steel work for gratings, frames, guard bar, ladder, railings, brackets, gates and similar works welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. all as specified and directed

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel steel works and painting synthetic enamel paint of approved. Two or more coats on new work all as specified and directed

M&L for 25 mm thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished, including cement slurry, but excluding the cost of nosing of steps etc. complete all as specified & directed.

Providing and laying Non skid Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.all as specified and directed

Providing and fixing white vitreous china battery based infrared sensor operated urinal having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Make : Hindware, product code : 60018

Providing and fixing white colour smart flow sensor operated Hand Dryer, dimension/size 145x138x258mm, sensing range 15-25cm, one piece cover in ABS thermoplastic + talcum base, fixed to base by two screws, class B brush motor, electronic infrared sensor type, PP UL94-V0 helicodial fan wheel, heating element incorporates a safety thermal cut-off all as per manufacturers specification and direction of Engineer-in-charge. Make : Jaquar, product code : HDR-WHT-M04A

Providing & fixing 15 mm nominal bore chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology all as specified and directed

Providing and fixing vitreous China counter type wash basin of size 595x420x200mm, weight 10.80 kg, make : Jaquar, model name : CNS-WHT-705 ll as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing & fixing of curve glass urinal partition straight shape dimenstion 450x900mm all as per manufacturers specification and direction of Engineer-in-charge.

M&L for Particle Board 12 mm thick Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked fixing in aluminum/wooden partion with Rubber/screw & as directed by EIC.

Demolition of cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

M& L for Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform (steel shuttering) all as specified and directed

Providing Thermo-Mechanically Treated bars of grade Fe-500D or more as in Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level all as specified and directed

Providing and laying in position reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)in all work up to plinth level, excluding the cost of centering, shuttering, finishing (reinforcement shall be measured and paid seperately) all as specified and directed

M&L distempering with oil bound washable distemper of approved brand and manufacture to give an even shade incl primer:(one coat) all as specified and directed

S & F 15mm Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and directed

Providing and laying in position cement concrete of 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) all work up to plinth level excluding the cost of centering and shuttering all as specified and directed

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge

M&L for RCC work 1:1.5:3 (1cement:1.5 coarse sand(Zone III) derived from natural sources:3 graded stone aggregate 20mm nominal size derived from natural sources) above plinth level upto floor five level, excluding cost of centering, shuttering finishing and form work all as specified and directed

M&L for 15 mm thick plaster in CM 1:4 on fair faces of walls , finishing the surfaces even and smooth w/o using extra cement all as specified and directed

M&L for Finishing walls with 100% Premium acrylic external emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm all as specified and directed

Providing and fixing 10 mm thick acid and alkali resistant tiles of approved make and colour using acid and alkali resisting mortar bedding, and joints filled with acid and alkali resisting cement as per IS : 4457, In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) complete as per the direction of Engineer-in- Charge.

M&L for roof treatment as follows:- (a) mechancial cleaning of surface in roof to make it free from any bituminous surface residue / dirt, oil and grease etc all as specified and as directed by GE / Engr-in-Charge. (b) Cracks treatment by cutting open cracks and cleaning it from dirt / loose materials etc and filling with polyurethane based sealant with and includig application of PU based primer all as directed by GE / Engr-in-Charge. (c) Applying water based polyurethane modified dispersion (single component, cold applied, non toxic, VOC coponent) in 03 coats including 01 coat of primer of same materials after dilution of water at 50% or specific primer matching same materials as per manufacture specification and as directed by GE / Engineer-in-Charge. A layer of Geo- textile grid of minimum 40 GSM sandwich in between two PU layers as per manufacturer's specification to be provided. Note : To be applied by the authorised applicator of the manufacturer only.

Supply only integral water Proofing compound

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Excavating over Area,exc 1.5 m but n.exc 3m deep in hard/dense soil soil complete all as specified and as directed

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m all as specified and directed

Removing of debris to a distance exc. 5 KM, but n.exc 15.0KM and depositing out side MD land all as specified and directed

Removing of excavated materials to a distance exc. 5 KM, but n.exc 15.0KM and depositing out side MD land all as specified and directed

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete of M30 grade with minimum cement content of 350 kg /cum for Basement slab , walls and cover slab for sump Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills, cover slabs and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) all as specified and directed

Centering and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases for columns all as specified and directed

Centering and shuttering including strutting, propping etc. and removal of form work for Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets all as specified and directed

Centering and shuttering including strutting, propping etc. and removal of form work for edges of slabs and breaks in floors and wall under 20 cm wide metre all as specified and directed

M & L , 15 mm cement plaster in two coats under layer 10 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 5 mm thick cement plaster 1:6 (1 cement : 6 fine sand) with water proofing compound all as specified and directed

M&L Finishing walls with Epoxy paint of required shade :New work (Two or more coats applied @ 4 kg/10 sqm) all as specified and directed

M & L for 110mm PVC (SWR) vent cowl complete all as specified and as directed

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete :Dumb bell with central bulb (180 mm wide, 8 mm thick) all as specified and directed

M&L PCC 1:2:4 type B -1(20mm graded aggregate)as in levelling course for fixing over head water tank on roof top and the like,including necessary form work etc. complete all as specified and directed

S&F rotational moulded polythelene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I 1000 Ltrs capacity all as specified and directed

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge.

S&F rotational moulded polythelene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I 5000 Ltrs capacity all as specified and directed

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 25 mm (Exposed on wall ) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 15 mm exposed on wall having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Providing and fixing ball valve (brass) of 25 mm , approved quality, High or low pressure, with plastic floats complete all as specified and directed

Providing and fixing gun metal gate valve of size 25 mm diawith C.I. wheel of approved quality (screwed end) all as specified and directed

Providing and fixing gun metal gate valve of size 20 mm diawith C.I. wheel of approved quality (screwed end) all as specified and directed

Excavation in trenches not exceding 1.5m wide and not exceding 10 sq m on plan and not exceding 1.5m depth and getting cut in Soft/loose soil all as specified and as directed.

Returing filling in including spreding leveling watering and well ramming in layer not exceding 25 cm as in soil all as specified and dirceted.

Removing excavated material (any type of soil) to a distance not exceding 50 m and depostingwhere directed at a level not exceding 1.5 mtr above the starting point all as specified and dirceted.

Supply and fix GI tubing medium grade ISI marked including all fittings laid in trenches / fixed on wall of size 50mm bore all as specified and as directed.

Material and Labour for cutting C.I. pipe with steel saw 150 mm diameter C.I. pipe Note :- Cutting of DI/CI pipe for Alternation or Addition of existing any size of pipe line and 150mm size of new lines laying complete all as specified and directed

S&F Brass full way valve with C.I. wheel (screwed end) 50 mm dia complete all as specified and directed. Note : - Supply and fix gate valve of size 50 mm dia with iron wheel head (ISI Marked), screwed both ends for iron pipe and fixed of size 50 mm bore

Cutting the existing hard standing/metal road to facilitate for laying of GI pipe line and making good the disturbed portion to bring it to original condition with PCC 1:4:8 type D2 using 40 mm graded stone aggregate all as specified and as directed.

PTMT Ball Cock 25mm complete with Epoxy Coated Aluminium Rod & H.D. Ball Note :- Ball valves high pressure of PTMT with epoxy coated alminium rod & high dencity plastic ball screwed for iron pipe an of 25 mm dia fixed for the following sizes incuding taking out existing unserviceable complete all as specified and directed (Minimum weight 15 mm -142 gms/200mm-20gms/25mm-455gms/40mm-690gms)

M& L Constructing masonry valve chamber of size 90x90x90cm of brick masonry valve pit of internal size 90x90x90cm with 230mm thick brick wall built in cement mortar 1:6, plain cement concrete foundation 1:4:8 type D2, plastering on brick surfaces 15mm thick in cement mortar 1:4 covered with MS plain sheet 3 mm thick duly fixed to MS frame size 40x40x6mm and duly embedded in plain cement concrete coping 5 cm thick plain cement concrete 1:2:4 type B1with opening and locking arrangements including painting with two coat of synthetic enamel paint over one coat of primer complete all as specified and as directed by Engineer in charge.

Supply, install, testing and commisioning of three phase controlling unit to control the switching operation of Air conditioners/Exhaust Fan in an alternative manner with PLC module.Rated current (In) of system is 63A at rated operational Voltage (Ue) of 415V AC ,with rated insulation voltage upto 500V AC voltage.Control unit shall have incomer with R Y B indications & all outgoing ckt shall have SCPD device in series with control devices.Control Unit enclosure shall be fabricated from CRCA sheet with sheet thickness of 1.6mm,finished with impact-resistant grey epoxy powder coating shade RAL7032 with IP54 degree of protection & suitable for wall mounted installations. Enclosure of control unit shall have earthing bolts for safety purpose & shall have detachable gland plates with for entry of cables ,with pad type locking facility also. Control Unit shall be manufactured in India at OEM plant & shall have QMS & EMS certifications like ISO9001, ISO14001 & ISO45001 to ensure good quality product complete all as directed and specified. (08 Nos for AC + 01 Nos for Exhaust Fan)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Note: Two runs of 4.0 sqmm copper cable,one run earth wire of 4.0 sqmm copper cable and 25 mm dia PVC conduit shall be measured and paid as one RM.

All as per item no.114 above but 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Note: Two runs of 2.5 sqmm copper cable,one run earth wire of 2.5 sqmm copper cable and 25 mm dia PVC conduit shall be measured and paid as one RM.

All as per item no.114 above but 4 X 4 sq. mm + 2 X 4 sq. mm earth wire Note: Four runs of 4.0 sqmm copper cable,two run earth wire of 4.0 sqmm copper cable and 25 mm dia PVC conduit shall be measured and paid as one RM.

All as per item no.114 above but 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Note: Four runs of 10.0 sqmm copper cable,two run earth wire of 6.0 sqmm copper cable and 32 mm dia PVC conduit shall be measured and paid as one RM.

All as per item no.114 above but 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Note: Four runs of 16.0 sqmm copper cable,two run earth wire of 6.0 sqmm copper cable and 32 mm dia PVC conduit shall be measured and paid as one RM.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including panel board including drilling holes in cubicle panles, making connections etc as required. (a) 125A, 16KA, TP MCCB

(b) 200A, 25KA, TP MCCB

Taking down carefully U/S aluminium/ copper point wiring (light, fan,socket or power) complete with fittings such as switches, sockets, ceiling rose, light fittings etc , removing all material for reuse/ issued under sch of credit and making good the distrubed surface as the existing one, complete all as directed.

Taking down MCB DB TPN/ SPN and making good to the disturbed wall of any Type complete all as specified and directed.

Taking down old sub main wiring of any type and size complete all as specified and directed .

Wiring with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit/casing capping on walls,floors. ceiling etc, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required for following:- Note: Two runs of 1.5 sqmm copper cable,one run earth wire of 1.5 sqmm copper cable and 25 mm dia PVC conduit shall be measured and paid as one RM. (a) One light point controlled by one way switch

All as per item no.124 above but One Fan point/Exhaust Fan point controlled by one way switch

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 and 15/16 Amps modular socket outlet and 15/16 A modular switch, connections etc as required.

Supplying and fixing 3 terminal, 5A ceiling rose on the existing junction box/wooden block including connections etc all as specified and directed

M&L for Stepped type Modular fan regulator(2 module) all as specified and directed

Dismantling the ceiling fan complete of any type and size from the various buildings and cleaning, servicing, greasing to bearings checking of nuts bolts , safety split pin, bushes , capacitor and complete testing after painting the ceiling fan ,blades ,down rod etc and refixing the site / bldg with complete connection all as directed and specified by Engr in charge. Note :- Expendable stores like cotton waste/cleaning materials, grease, lubricants, machine screws, safety split pin, bots/nuts and transportation to and from site to work place are deemed to be included in rate quoted

Supply and replacement of LED type 4 feet tube light batten fitting surface mounted of 20 Watts extruded aluminium housing high lumen output complete including taking down old one all as specified and directed .

Supply and replacement LED mirror light fitting surface mounted of capacity of 10W with plastic body and accessories complete all as specified. including connecting to ceiling rose with twin copper conductor of size 0/0.24 complete including taking down old one all as specified and directed .

Supply & fix exhaust fans Steel body of size 300 mm sweep with AC single phase 230/ 240 V ,speed 1400 RPM with complete louver fixed in out side with making a hole as required at site with all fixing arrangment at reqd at site complete finishing work complete with all connections all as specified and directed by Engr-in charge.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required and directed by Engr in Charge.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required and directed by Engr in Charge.

Supplying and fixing of following ways surface/ recess mounting, vertical type,4 way (4 + 12), Double door), 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required and directed by Engr in Charge. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required).

Supplying and fixing SP 5A to 32A rating 240/415 V, 10KA 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete testing and commissioning etc all as specified and directed .

All as per item no.136 above but Triple pole and neutral all as specified and directed .

All as per item no.136 above but Triple pole all as specified and directed .

All as per item no.136 above but Single pole and neutral all as specified and directed .

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt all as specified and directed . Note : (i) Rate quated shall deemed to include cost of excavation in any type of statra,RFR and removal upto 50 meter,PCC Pit,funnel and RCC cover plate,GI pipe etc. (ii) Earth resistance not exceeding 1.0 ohm.

Providing and fixing 6 SWG dia GI wire on surface or in recess for loop earthing as required. as required at site and directed by Engr In Charge.

M & Labour for laying of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of size 35.0 sq mm 3.5 core all as specified and directed .

Supply and spread clean dry river sand traveles for cushing of UG cables all as specified and directed . Note: Punned thickness of sand will measured for payment purpose.

M&L for common burnt clay building bricks sub class 'B' laid in trenches over sand cushioning for protection of UG cable in trenches all as specified and directed .

M & Labour for demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as specified and directed .

M & L for PCC (1:3:6) type C1 using 20 mm graded aggregate for making good the disturbed portion of road/floor/platform etc including form work compaction etc all as specfied and directed by Engineer-in-Charge.

M & L for GI pipe medium grade, for road crossing / on wall / on pole for cable protection of following size 25 mm dia all as directed and specified by Engr in charge.

Supplying and fixing LED tube light along with fixture 18 watts complete all as specified as directed.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 125 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required for 8 way (4 + 12), Double door.

Providing and fixing following rating and breaking capacity and 4 pole MCCB with hermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections of size 125 A to 160A, 35KA, 50Hz 415V, FP MCCB etc. as required.

YASHASVI BUILDERS

Anjali Constructions

m/s raghavendra kulkarni