Construction of New Bus Depot at Khadgarha Bus Stand under Ranchi Municipal Corporation, Ranchi.

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item B)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto plinth level 1:2:4 (20 mm nominal size)

Providing designation 75 B brick work in C.M.(1 :6) in foundation & Plinth with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 B brick work in C.M.(1 :6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering and shuttering --- do------ 1:1.5:3 (20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, band, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement: with 1.1.5.3

Reinforced cement concrete work in walls(any thickness),including attached pilasters, buttresses,plinth and string courses,fillets columns,pillars,piers,abutments,posts and struts etc.above plinth level up to floor five level,excluding cost of centering,shuttering,finishing and reinforcement: 1:1.5:3(1 cement :1.5 coarse sand(zoneIII):3 graded stone aggregate

Providing and laying damp proof course 50 mm thick with cement concrete M-150 with nominal mix of (1:2:4) ….do…..

Providing tor steel reinforcement of 8mm.,10mm,12mmm&16mmmdia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. Taking 8mm TMT FE 500 ( only valid for Tata (Tiscon) SAIL, JSPL, Electro Steels Ltd., Bokaro, & Vizag (RINL) 5.5.4 8 dia

10mm dia

12 and above dia

centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Lintels,beams,plinth beams girders,bressumers and cantilevers

Suspended floors,roofs,landings,balconies and acess platform

shelves

Columns,pillars,piers,abutments,post and struts

stairs,(excluding landing)except spiral-staircases

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing & fixing pressed steel door frames manufactured from commercial mild steel sheet of 1.25mm thickness including hinges ,jamb, lock jamb, bead and if requiredangle threshold of mild steel angle section 50 X 25mm, orangle threshold of mild steel angle section 50 X 25mm, orbase ties of 1.25mm pressed mild steel welded or rigidlyfixed together by mechanical means, adjustable lugs withsplit end tail to each jamb including steel butt hinges split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and 2.5mm thick with mortar guards, lock strike-plate andshock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by the Engineer Incharge - Profile - B - Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinfoorced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Enginner-in-Charge.

30mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm . 19mm for styles and 15x15mm for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on eigher side forming styles: and 5 mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mmshall be tapered in 45 degree on the inner side to form top and bottom raiil and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided eigher side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded / sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer's specificatio n& drawing (for W.C. and bathroom door shutter).

providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) tramsparent or dyed to required colour or shade with necessary screws etc. complete 125X75X4mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete Twin rubber stopper

Providing and fixing luminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transpoarent or dyed to required colour or shade with necessary screws etc. complete 150X10mm

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or deyed to required colour or shade with nuts and screws etc. complete 250X16mm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285 fixing with dash fasterners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required DPDM rubber/neoprene gasket etc., aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling C.P. brass/stainless steel screws, all complete as per architetural drawings and the directions of Engineer-in-charge (Glazing, panelling and dash fasteners to be paid for separately) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required inlcluding the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for separately) --- Polyester Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, windows, ventilators, shutters and partitions etc, with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge (cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4mm thickness

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

supplying,fitting and fixing fully glazed door,window or ventilators of standard rolled Z and mullion steel sections and size as per IS 1038 joints met …....do….all as per specification and direction of E/I.

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by deptt.)

Providing and fixing stainless steel (grade 304) railing made of Hollow tubes, channels, plates etc,. Including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessry stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasterners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasterners etc,.)

Providing and laying 15 to 23mm thick Kotah stone tiles in risers of steps, skirting and pillars of approved size, taxture and colour and over 12mm thick cement mortar (1:3) and joined with grey cement slury mixed with pigment to match the shade of the slab including rubbing to granolithic finish with approved quality of carborandum stone including cost of curing, txes and royalty all complete as per building specifiction and direction of E/I.

Providing and laying double charged Vitrified floor tiles in different sizes (thickness to be specificed by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622/ISO 13006 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting thenjoints with white cement and matching pigments etc. complete size of tile 600X600mm

Providing and laying rectified glazed ceramic floor tiles 300x300m or more (thickness to be specified by manufacture) of 1st quality conforming to IS:15622 with approved make in colours white, ivory, grey, fume red, brown laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments, etc all complete.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/l. a With "A" grade white 15 x 15 cm tiles.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providign and applying Plaster of Paris Putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of oil bound distemper ofapproved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Finishing walls with premium acrylic smooth exterior paint with sillicone additives of requited shade . New work : 2 or more coats applied @1.43 Ltr/10sqm over and including base coat of waterproofing cement paint applied @2.2 Kg/10 sqm

Providing French spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including cleaning the surface after removing dirt, scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specifcation and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. Bend 87.5 degree 110x110x110mm

Shoe (Plain) 110 mm shoe

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means 50X50X50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete - 110mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS: 8931. 15 mm nominal bore

Providing and fixing PTMT swiveling shower, 15 mm nominal bore, weighing not less than 40 gms

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and placing on terrace (at all floor levels) Polythene water storage tank of IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fittings and thebase support for tank. (e.g. Sintex etc.)

providing and fixing white vitreous china flat back or wall corner type lipped front urinal…....do…E/I one urinal basin with 5 litre white p.v.c automatic flushing cistern

Providing and fixing chlorinated polyvinl chloride (cpvc) pipes having thermal stability for hot and cold water supply including all cpvc plain &brass theaded fitting,including fixing the pipe with clamps at 1.00 spacing.This includes cement ane testing of joints complete as per direction 20mm nominal dia pipes

32mm nominal dia pipes

constructing masonry chamber 60x60x75cm inside,in brick work in cement mortar(1:4)for water meter completewithC.I double flap surface box 400x200x200mm inside with locking arrangement and rcc top slab 1:2:4…...do…. Chamber

Making soak pit 2.5m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with bricks and s.w drain pipe 100mm diameter 1.8m long complete as oper standard design Soak Pit

Water proofing for old and new roof slab….... Do........

Bricks - 7KM + 1 km.

Local sand 18 km

Sand - 42km

Chips - 15km

Stone Dust (Lead 15 KM)

Earth (Lead 01 KM)

Stone Boulder (Lead 29 KM)

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Stone Crusher Dust finer than 3 mm with not more than 10% Passing 0.075 sieve at quarry.

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttring- All work up to plinth level. 1:1.5:3 (20 mm nominal size)

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Iron and Steel Material 50x50x 6/8/10

Providing two coat of Snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper ……..do……

Construction of granular sub-base by providing close graded material,mixing in a mechaniclal mix plant at OMC,carriage of mix Material to work site, spreading in uniform layers with moter grader on prepared surface and compacting with vibratory power roller to achieve the desired density complete as per clause 401.

Providing and laying80 mm Thick factory made Cement Concrete paver block of M-40 grade made by block making Machine with strong vibretory compaction of approve size,design and shape ,laid in rerequired collour and pattern over bed as per revalent IRC Code ,filling the joints with fine sand etc all complete as per direction of Engineer -in -Charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 6" dia Pipe

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces),excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80 mm thick with zinc coating not less than 275 gm/m²

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.10.16.3 Electric resistance or induction butt welded tubes

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I.limpet and bitumen washers complete.12.4.2 0.63 mm thick with zinc coating not less than 275 gm/m² GI Ridge

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete 12.7.2 0.63 mm thick with zinc coating not less than 275 gm/m² G.I. SHEET GIRDER

Supplying and laying (properly as per design and drawing) rip-rap with good quality of boulders duly packed including the cost of materials, royalty all taxes etc. but excluding the cost of carriage all complete as per specification and direction of E/I.

NVR 16 CHANNEL

PTZ CAMERA 5MEGA PIXEL

PTZ CAMERA 5MEGA PIXEL

DOME CAMERA 5 MEGA PIXCEL

BULLET CAMERA 5MEGA PIXCEL

POE SWITCH 8 PORT

CAT 6 CABLE

INSTALLATION

HARD DISK 2 TB

Finishing walls with Premium Acrylic Smooth exterior paint with silicone additives "Snowcryl - XT" of M/S Snowcem India Ltd, or equivalent of required shade. New work (Two or more coats applied @1.43 ltr / 10sqm. Over and including base coat of water proofing cement paint Snowcem Plus or equivalent applied @ 2.20 kg./10 sq.m. )

Dismentalling of Rienforced Cement Concrete and………..Do…..E/I.

Providing 2 coat of S E paint over steel surface all complete job

supplying and drawing following sizes FR PVC insulated copper conductor ,singe core cble in the existing/recessed steel/PVC conduit as required JSR 1.15 2 X 1.5 sq mm

2 X 2.5 Sq mm

2 X 6 sq.mm

10 Sq mm ISI marked, FR LS PVC insulated, single core copper conductor cable

35 sq.mm ,3.5 core alluminium armoured cablr

S/F modular type switch/socket : Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 5 pin 5/6 amp 3 pin socket outlet

5/6 amps. One way Switch

15/16 amp one way switch

15/16 amps.6 pin socket outlet

25 mm dia ISI marked ,PVC conduit

Batten holder:- supplying and fixing batten/angle holder including connection as required

S/F Ceiling rose:- Supplying and fixing 2pin 5amp. Ceiling rose on the existing juction box/wooen block includinhg connection as require

Decorative ceiling fan 48"(1200)

9"(300mm) ,metal exaust fan

Electronic step fan regulator delux

S/F modular boxes,base &cover plate:- supplying and fixing following size/modules,GI box along with modulerbase& cover plate for moduler switches in recess etc as required switch/ socket on the existing switch box/ cover including connections etc. as required.JSr 1.27 4/5 module(78mmx140mmx50mm)

6 module(78mmX205mmx50)

8/9 module (78mmX230mmX60mm)

12 module (135mmx205mmX60mm)

6 way, SPN single door MCB DB

8 way,(4+24),TPN MCB DB single door

6 amps MCB SP

6 to 32 amps. Rating MCB SPN C series 10 kva

100 amps,4 pole RCCB,100mA/300mA

50/63 amps ratingTPN MCB C series 10 kva breaking capacity

Providing ad fixing following capacity busbar chamber with 4 strip of length 300 mm made of copper suitable for following capacity complete with all accessories including connection,earthing the body etc as required 100 amps

Sheet metal ON/OFF load changechangeovercapacity 4 pole with side handle in existing metal boardincluding drilling holes in metal board ,marking connection earthing the body etc as required 100 amps 4 pole

LED Flood light120 Watt

15/16 Watt LED Bulb

Vertical type panel board(4'x5')

80mm dia Earthing electrode 2mtr Lendth / 80mm dia Earthing electrode 3mtr length / 50 mm dia earthing electrode 2mtr length /50 mm dia earthing electrode 3mtr length & backfill compound chemical 4 bag(per bag 25 KG)

GI wire 10 SWG

Silent type DG set of capacity 100 KVA with AMF pannel IS/IEC600341 IS:1460 IS:13018 …. Do…….

Supplying all materials, labours and tools and equipment for drilling 200 X 165mm dia. X 125 Mtr. bore well in all kinds of soil and rock in urban area for installation of pumps set with Hydraulic DTH Rig Machine, all complete including drilling rig, Air Compressor and equipments, as well as fuel, lubricants and cost of transporation of rig machine and over vehicles up to the site etc. all complete job as per specification and direction of E/Ic. I - From 0.00 M to 50.00 M below G.L.

II - Beyond - 51.00 M to 225.00 M below G.L.

Supplying all tools, tackles & lowering of 200mm dia. MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe etc including all taxes, VAT, Excise duty, freight charges with inspection charges etc as applicable, etc. all complete job as per specification and direction of E/I.

Cleaning flushing and developing of drilled hole for testing the discharge of water development of bore well by continuous flow of water by using heavy compressor up to satisfaction of E/I. to get uninterrupted flow of water free from sand and soil etc.

Supplying all materials: labours, tools & equipments for fiting & fixing 200mm dia MS cap over casing pipe etc. all completes job.

Supplying of 150mm dia 03.00 H.P. (ISI Mark) KSB/Kirlosker/CRI/V-guard Submersible Motor Pump sets comfirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50Hz, A.C. supply with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non returned valve shall be provided with pump. 3 meter submersible copper in single/double run shall be provided with each pump.(up to 20 stages) Supply rate should be increased by Rs 200/- per stage for pump with more than 20 stages.

Supplying of 4.0sqr. mm. cable ISI Marked for above requirement.

Supplying of 32 mm Submersible Pipe of standard make Ashirwad/Raksha/Prince/Gupta or any equivalent make for above requirement.

Supplying of 02 Nos. clamp, Band, Adopter, Bore Cover etc. as required for above work.

Supplying & fixing Electric Meter (L&T or Equivalent) 03 Phase Main Switch of ISI Mark as per direction of E/I.

Intenel wiring and Lighting arrangement in Pump House.

Supplying & Providing Rope of required size & tape.

Supplying & Fixing of BCH Make or Equivalent Panel Board with all accessories & Iron Box with Angle Stand and its fixing as per direction of E/I.

Supplying & Fixing of Wooden box of Required Size for Panel Board. Electric Meter, Main Switch etc.

Installation Charges for Lowering of Motor Pump.

Supplying and of 10.0sq.mm Alluminium cable ISI mark as per specification and direction of E/I. (for connection from main line to electric Meter.

03 Phase Electric connection charge payable to JSEB, Ranchi.

Construction of Brick masonary chamber with RCC Slab as per E/I. (Annexure-K)

Supplying Fittings & Fixings PVC water storage Tank of Approved Quality with all fittings. Supplying all materials, labours, tools and equipment for laying PVC Schedule 80 pipe water flow, supreme or any ISI approved make in trenches with red lead and yarn with socket and screw joints and cutting pipe to size and threading ends where necessary etc. all complete as per specification and direction of E/I. (a) 50mm dia PVC Sch.-80 Pipe

(b) 40mm dia PVC Sch.-80 Pipe

(c) 32mm dia PVC Sch.-80 Pipe

(d) 25mm dia PVC Sch.-80 Pipe

Supplying and fixing G.I. /PVC fittings of approved make all complete as per specification and direction of E/I. (a) Elbow : 50mm dia

(b) Elbow : 40mm dia

(c) Elbow : 32mm dia

(d) Elbow : 25mm dia

(e)Tee plain 50mm dia

(f)Tee plain 40mm dia

(g)Tee plain 32mm dia

(h)Tee plain 25mm dia

(i)Socket Plain 50mm dia

(j)Socket Plain 40mm dia

(k)Socket Plain 32mm dia

(l)Socket Plain 25mm dia

(m)Union Socket 50mm dia

(n)Union Socket 40mm dia

(o)Union Socket 32mm dia

(p)Union Socket 25mm dia

providing and fixing male ended 15mm dia UPVC bib cock of approved quality as per specification and direction of E/I.

Supplying and fitting UPVC valve of approved quality as per specification and direction of E/I. 50mm dia F/W Valve

Providing all materials, labour, tools and equipment for fixing HDPE water storage tank double layer of approved make conforming to ISI-12701-1995 fixing on the staged pillar or on the roof of the building including cutting 4 Nos. hole in tank for rising over flow delivery and wash out including supplying full thread nipple with jam nut and fixing connection etc. and supplying and fixing brass ball cock of required size as per specification and direction of E/I (ISI marked double layer sintax, Himgiri or Gangotri or Equivalent make) 1000/2000liters capacity @ Rs. 06.20 Per Litre.

Supplying Tools & Cutting Road as well as restoring the same specification & direction of E/I. 30m X 0.4m = 12.0m2

Supplying all materials, tools and equipment for making brick masonry platform about 75mm high and diameter of the tank including PCC(1:2:4)25mm thick over it and cement plaster (1:4)with punning with 5% cico on the roof of the building all complete as per specification and direction of E/I.

Earthwork in back filling in trenches after laying different type and size of pipe with earth removed during excavation within initial lead and left as per specification and direction of E/I. (For classification of soil item A & B)

Supply of 16 mtr. High Mast in two section Construction S355 grade as per BS-EN 10025 Top Dia 150mm, bottom dia 360mm, plate thickness 3mm, 20 side polygon galvanisation as per BS-EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike lighting protection, maximum wind speed 47 m/s with 6 nos. foundation bolt of PCD 445mm TS 600/24mm dia/850 mm long. Luminaires carriage:Material for 40 NB ERW Class B- M.S. Pipe, dia of carriage ring 450mm (ID) with 8/12 arm, welded, 2 sections having carrying capacity upto 8/12 luminaries. Trailing cable : 5 core 2.5 sqmm. PVC flexible copper conductor winch / Power Tool : Double drum, SWL 350 kg with 1 HP 6 pole single speed intergal motor Rope: Grade AISI 304, 7/19 construction, dia 5mm, BLC 1450 x 2 having 2 nos. of continues rope, Aviation obstruction light: twin dome aviation obstruction lights LED type as required. Feeder piller: control panel housing 63A TPN MCB incomer, single dial timer, 45A contactor circuit for the automatic control of luminaries power tool control with 2 no. 9A contactors and raise lower push button, incommer 35sqmm. and outgoing 16 & 2.5 sqmm. terminals.

For 16 mtr. High mast: ITC of the high mast and light fixture with the help of suitable tools and plants, wiring of luminaries with all wiring material like PVC insulated PVC sheathed flexible cable of suitable copper conductor lugs. MCB and all labour & construction of shallow foundation with M25 grade concrete for the high mast considering safe soil bearing capacity of 10T/mtrs sq. for 16 M High Mast

LED FLOOD Light 240 W

Supply of 4C x 16 sqmm Aluminum Armored XLPE Cable

Laying of one number PVC insulated and PVC sheathed / XLPE power cable 1.1 KV grade of size not exceeding 35 sqmm direct in ground including excavation sand Cushing protective covering and refilling the trench etc. as required

Earthing with GI earth pipe 4.5 mtr. Long, 40mm dia including accessories, and providing masonary enclouser with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required

Supplying and laying 6 SWG GI wire at 0.5 m below ground level for conductor earth electrode, including soldering etc. as required

Supply and installation of 2 brush fully automatic bus washing system.

Add 18% GST (In Basic Rate must fill 18)

Add 1% Labour Cess (In Basic must Rate fill 1)

M/S SIDHI VINAYAK CONSTRUCTION

Bidder Name

BRIJENDRA PRATAP SINGH

M/S SIDHI VINAYAK CONSTRUCTION