Construction of Govt. Senior Secondary School Building at Baat (SH Construction of ground floor including WS and SI ,septic tank and site development)

Amount

Cutting in earth work in all height and depth in all kinds of soils including saturated soil comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soil including dewatering wherever required, setting out true to the required lines, grades, width, cutting, side slopes, trimming of bottom and levels as shown in the drawings and as directed by the Engineer-in-charge at site, according to the HPPWD specification and sorting of useful and un-useful material for filling in roadway, embankments for grade improvement and leveling to the required grades and then disposing of all excavated materials in acquired width of the road or on approved dumping site/sites through all modes of transportation including head load, animal loads or mechanical means along with its leveling and fine dressing and carriage of all labour, machinery, materials, tools equipments and safety measures and other incidentals necessary to complete the work by mechanical means and /or by labour (if any required complete as per the direction of the as per the direction of the Engineer-in-charge. Any loss to the public and private property during the course of execution and transportation of useful and un-useful materials shall be absolute responsibility of the contractor which shall have to be duly compensated by the contractor to full extent in all respect and in all cases. Engineer-in-charge. Any loss to the public and private property during the course of execution and transportation of useful and un-useful materials shall be absolute responsibility of the contractor which shall have to be duly compensated by the contractor to full extent in all respect and in all cases. The rate including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Excavation in earth work etcetra in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, blasting work both in soft and hard rock, chiesling / wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil setting out ture to the required lines, grade, width, cutting and trimming of side slopes as shown in the drawing and if water is met within the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable divertion pumping or bailing out and excavation shall be kept dry whereever so required by the contractor at his own cost as directed by the Engineer-in-charge and disposal of all surplus excavated soil in acquired width or at an approved dumping side including its stacking leveling dressing in all leads and lifts by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machinaries and other incidentals to complete the work as per HPPWD specification. Any loss to the public and private property during the course of execution and disposal of unserviceable material shall be absolute responsibility of the contractor which shall have to be compensated by him in all cases.The rate including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Excavation in foundation and trenches in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rock, chiseling / wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil setting out true to the required lines, grade, width, cutting and trimming of side slopes as shown in the drawing and if water is met within the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable diversion pumping or bailing out and excavation shall be kept dry wherever so required by the contractor at his own cost as directed by the Engineer-in-charge and disposal of all surplus excavated soil in acquired width or at an approved dumping side including its stacking leveling dressing including all leads and lifts by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machineries and other incidentals to complete the work as per HPPWD specification. Any loss to the public and private property during the course of execution and disposal of unserviceable material shall be absolute responsibility of the contractor which shall have to be compensated by him in all cases.The rate including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Excavation in drains and channels etcetra in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, blasting work both in soft and hard rock, chiesling / wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil setting out ture to the required lines, grade, width, cutting and trimming of side slopes as shown in the drawing and if water is met within the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable divertion pumping or bailing out and excavation shall be kept dry whereever so required by the contractor at his own cost as directed by the Engineer-in-charge and disposal of all surplus excavated soil in acquired width or at an approved dumping side including its stacking leveling dressing in all leads and lifts by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machinaries and other incidentals to complete the work as per HPPWD specification 1990 Vol.I. Any loss to the public and private property during the course of execution and disposal of unserviceable material shall be absolute responsibility of the contractor which shall have to be compensated by him in all cases.The rate including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including all taxes, GST ,carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in foundation, footing, basis of columns etcetra and mass concrete including all taxes, GST,carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, pillars, posts and struts square rectangular or polygonal in plan including all taxes, GST, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights from floor including all taxes, GST, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetra upto any thickness including all taxes, GST,carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stair cases with sloping or stepped soffits excluding landing including all taxes, GST,carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling upto any heights and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls upto all width and heights including all taxes, including carriage of material and other incidentals within all leads and lifts and as per the direction of the Engineer-in-charge.

Providing and laying mechanically mixed and vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 330 Kg/Per cubic metre ( Three hundred thirty kilograme per cubic metre) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundations, footings bases of columns and the like and mass concrete including all taxes,GST, carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals.

Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 330 Kg/Per cubic metre ( Three hundred thirty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in columns, pillars, posts and struts upto floor all levels as per the directions of the Engineer-in-charge including all taxes, GST,carriage of material within all leads and lifts and other incidentals.

Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 330 Kg/Per cubic metre ( Three hundred thirty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landing, shelves and their support, balconies, beams, girders, bressumers and cantilever upto floor all levels as per the directions of the Engineer-in-charge including all taxes, GST, carriage of material within all leads and lifts and other incidentals.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone agreegate 20 mm (twenty millimetre) nominal size) curing complete excluding the cost of form work in foudation and plinth within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone agreegate 40 mm (forty millimetre) nominal size) curing complete excluding the cost of form work in foudation and plinth including all taxes, GST, carriage of material, within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:5:10 (one cement isto five sand isto ten graded crushed stone agreegate 40 mm (forty millimetre) nominal size) curing complete excluding the cost of form work in foudation and plinth including all taxes, GST, carriage of material, within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing 100mm (Hundred millimeter) diametre PVC pipe of finolex make 6 Kg ( six kilogram) pressure per square centimetre Weep holes in brick masonry/stone masonry, plain/reinforced concrete abutments, wing walls return walls and retaining /breast walls etctra extending through the full width of the structure with slope of 1 (V) : 20 (H) (one vertical is to twenty horizontal ) towards drawing face complete as per drawings and MORD technical specifications clause 614, 709, 1204.3.7 or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Back filling with granular material behind abutments, return walls, wing walls and retaining walls etc. complete as per drawings and MORD technical specification clause 1204.3.8 or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing tor steel reinforcement for reinforced cement concrete work including straightening, bending, binding and placing in position complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Stone filling under floor/ behind retaining wall etctra complete including all taxes and carriage of material, as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Random rubble masonry/polygonal rubble masonry (uncoursed / brought to courses ) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto twelve graded stone agreegate 20mm (twenty millimetre) nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand) as per the directions of the Engineer-in-charge including all taxes and carriage of material within all leads and lifts and other incidentals.

Squared rubble masonry coursed with hard stones of approved quality in foundation and plinth including raking out joints in cement mortar 1:6 (one cement is to six sand) curing complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Second class brick work using common brunt clay building bricks of approved quality in super structure above plinth level upto floor all levels in cement mortar 1:6 (one cement isto six sand) curing complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Half brick masonry using second class common brunt building brick with hoop iron of approved quality in super structure above plinth level upto floor all levels in cement mortar 1:4 (one cement isto four sand) curing complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Second class brick work using common brunt clay building bricks in foundation, plinth in mud mortar including and carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing ISI marked 35 mm ( thirty five millimetre) thick flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1stclass hard wood and well matched teak 3 ( three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked stainless steel butt hinges with necessary screws as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing cup board shutters with 25 mm ( twenty five millimetre) thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including 2nd class teak wood lipping of 25 mm ( twenty five millimetre) wide x 12 mm ( twelve millimetre) thick with decorative veneering on one side and commercial veneering on other side with necessary screws and bright finished stainless steel piano hinges, complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 65 mm ( sixty five millimetre) special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 200x10 mm ( two hundred into ten millimetre) aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etcetra complete 250x16 mm (two hundred fifty into sixteen millimetre) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etcetera complete 125 mm (one hundred twenty five millimetre) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etcetera complete 75 mm ( seventy five millimetre) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing M.S. plain grills 10x10mm (ten into ten millimetre) square or round bars in combination of 20x4mm (twenty into four millimetre) M.S. flat as per detail of required pattern in frames of windows etc.with M.S.Flats, square or round bars with round headed bolts and nuts or by screws as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and laying vibro hydraulic compressed and polished precast terrazo tiles 20mm (twenty millimetre) thick of 300mm X 300mm (three hundred millimetre into thre hundred millimetre) size ISI mark No. 1S237 with 70% (seventy percent) white and 30% (thirty percent) grey cement with marble chips ratio of 55% (fifty five percent) white and 15% (fifteen percent) each of green, yellow and maroon shade of specified sizes laid in floors, treads of steps and landings on a bed of 25mm (twenty five millimetre) average thicknes of cement mortar 1:4 (one cement isto four sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (where ever required) including rubbing and polishing complete including carriage of material as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and laying vibro hydraulic compressed and polished precast terrazo tiles 20mm (twenty millimetre) thick (with marble chips of specified sizes) fixed on wall on 10mm thick cement plaster 1:3 (0ne cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles including rubbing and polshing complete mark No. IS237 with 70% (seventy percent) white and 30% (thirty percent) grey cement with marble chips ratio of 55% (fifty five percent) white and 15% (fifteen percent) each of green, yellow and maroon shade of specified sizes in skirting and risers of steps not exceeding 30 cm (thirty centimetre) in height as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm (three hundred into three hundred) or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm(twenty millimetre) thick cement mortar 1:4 ( one cement isto four Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm ( three point three kilogram/square metre) including grouting the joints with white cement and matching pigments etc., complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 18 mm ( eighteen millimetre) thick marble work gang saw cut, mirror polished, premoulded and prepolished,machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm ( twenty millimetre) thick base cement mortar 1:4 (one cement isto four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Chequered terrazo tiles 22 mm ( twenty millimetre) thick with graded marble chips of size up to 6 mm ( six millimetre) in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm ( twenty millimetre) thick bed of cement mortar 1:4 (one cement isto four coarse sand) ordinary cement without any pigment as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and laying Ceramic glazed floor tiles of size 300x300 mm ( three hundred into three hundred) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm ( twenty millimetre) thick cement mortar 1:4 (one Cement isto four coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm ( three point three kilogram/square metre) including pointing the joints with white cement and matching pigment etc., complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Structural steel work riveted, bolted or welded in built in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a primming coat of red lead paint in gratings framed gaurd bars, ladders, railing, brackets and similar works as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel angle sections of size 35x35x5 mm ( thirty five into thirty five into five millimetre) joints mitred and welded by angle iron 35x35x5 mm ( thirty five into thirty five into five millimetre) or 35x 5 mm ( thirty five into five millimetre) flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat ofapproved steel primer, all complete as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges,pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured forpayment) as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing & fixing Galvanised M.S. Wire gauze with 0.63 mm ( zero point six three millimetre) dia wire and 1.4 mm ( one point four) aperture on both side fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm ( fifteen into three millimetre) and nuts & bolts complete as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing & fixing 4 mm ( four millimetre) thick glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 0.60mm (zero point six zero millimetre) thick prepainted steel sheets of TATA Durashine in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron (twenty micron) over 5 microns (five micron) primer coating and back coat of polyster of 5 microns (five micron) over 5 microns (five micron) primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet washers complete with all accesories as required including all taxes, carriage of material within all leads , lifts and as per specification approved drawing & Design or as per the direction of the engineer-in-chief and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing ridges or hips 60cm (sixty centimetre) overall 0.60mm (zero point six zero millimetre) thick prepainted steel sheets of TATA Durashine /SAIL/ Zindal steel in roofing having proper gola shape with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron (twenty micron) over 5 microns (five microns) primer coating and back coat of polyster of 5 microns (five microns) over 5 microns (five microns) primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet washers complete with all accesories as required including all taxes, carriage of material within all leads,lift and as per specification approved drawing & Design or as per the direction of the engineer-in-chief and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing valley 90 cm. (ninety centimetre) overall with 0.60mm (zero decimal six millimetre) thick prepainted steel sheets of TATA Durashine /SAIL/ Zindal steel in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron over 5 micron primer coating and back coat of poltster of 5 micron over 5 micron primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia and prepainted G.I. limpet and bitumen washers complete with all accessories including all taxes, carriage of material within all leads and lifts and as per specification approved drawing & design or as per the direction of the engineer-in-chief and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing M.S. B.P. sheet 1.66mm (one point six six millimetre) any thickness in eaves board / facia / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 40 mm( forty millimetre) dia M.S. hollow pipe hand slip resistant with rounded at PWD level at 75 to 90cm railing with 50 mm ( fifty millimetre) dia pipe fixed to vertical member @ 60 cm (sixty centimetre) centre to centre including carriage of materials within all leads and lifts as per the direction of Engineer-in-Charge and other incidentals. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing hand rail readymade M.S. hollow pipe D-section 50x50mm (fifty into fifty millimetre) diametre over 23cm.(twenty three centimetre) thick brick wall parapet with baluster 20x20mm (twenty into twenty millimetre) solid square bars etc. complete including carriage of materials within all leads, lifts as per specification as per the direction of the Engineer-in-charge and other incidentals.The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm ( twenty into ten into two millimetre) and braced with flat iron diagonals 20x5 mm ( twenty into five millimetre) size, with top and bottom rail of T-iron 40x40x6 mm, ( forty into forty into six millimetre) with 40 mm ( forty millimetre) dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer as per the direction of the Engineer-in-charge and other incidentals.The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter with Readymixed paint brushing wood primer pink as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Painting two or more coats (excluding priming coat ) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering and stoping with enamel paint other than whiteas directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Painting two or more coat (excluding priming coat) on new steel and other metal surfaces under coat with ready mixed paint brushing to give an even shade including cleaning the surface all dirt, dust and other foreign matter with enamled paint other than whiteas directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

6mm (six millimetre) thick cement plaster to ceiling in cement mortar 1:3 ( one cement isto three sand) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

15mm (fifteen millimetre) cement plaster in single coat on rough side of brick / concrete / stone masonry for interior plastering upto floor all levels including arises, internal rounded angle, chamfer and / or rounded angle not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement isto six sand) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

20 mm (twenty millimetre) cement plaster with groove in pattern in single coat on fair side of brick / concrete / stone masonry for interior plastering upto floor all levels including arises, internal rounded angle, chamfer and / or rounded angle not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement isto six sand) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

20 mm (twenty millimetre) thick cement plaster in single coat on fair side of brick / concrete / stone walls for interior plastering upto floor all levels including arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth with cement mortar 1:3 (one cement isto three sand) as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals.

Finishing walls with Apex weather proof exterior grade emulsion of Asian paint or exterior emulsion of NAROLAC SURKSHA as per approved shade on undecorated wall surface (two or more coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals.The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Distempering two coats with oil bound washable distemper of approved brand and manufacture and of required shade on un-decorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and including preparing the surface even and sand papered smooth as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing on wall faces PVC (D-plast) 110mm dia (one hundred ten millimetre diametre) rain water pipes working pressure not less than 4.5 Kg (four point five) kilogram per square metre including filling the joints with approved adhesive complete within all leads and lifts and as per the direction of the Engineer-in-Charge and other incidentals.

Providing and fixing on wall faces PVC (D-plast) 110mm (one hundred ten millimetre) dia PVC plain bend for rain water pipes including filling the joints with approved adhesive complete within all leads and lifts and as per the direction of the Engineer-in-Charge and other incidentals.

Providing plinth protection 50 mm (fifty millimetre) thick in cement concrete 1:3:6 (one cement isto three sand isto six graded stone agreegate 20 mm(twenty millimetre) nominal size) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Constructing course rubble hammer dressed 'U' shape open surface drain with side wall 15 X 23 cm (fifteen into twenty three centimetre) in cement mortar 1:6 (one cement isto six sand) and inside plastering with cement mortar 1:3 (one cement isto three sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (one cement isto five sand isto ten graded stone agreegate 40 mm (foty millimetre) nominal size) and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (one cement isto two sand isto four graded stone agreegate 20 mm (twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) of Hindware with seat and lid, 10 ( ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls andfloors wherever required : W.C. pan with ISI marked white solid plastic seat and lid as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing white Vitreous China wash basin of Hindware with C.I. brackets, size 630x450 mm ( six hundred thirty into four hundred fifty millimetre) with a pair of 15 mm ( fifteen millimetre) C.P. brass pillar taps , 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing vitreous China pedestal of Hindware for wash basin complete recessed at the back for wash basin complete recessed at the back for the reception of pipes and fittings as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing C.P. brass Zet ISI marked IS NO. 8934 of Hinware/Jaquar with necessary screws complete as per approved drawing, design & specification or as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. brass waste of 32mm (thirty two millimetre) dia size for sink or wash basin as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 100 mm ( one hundred millimetre) sand cast Iron grating for gully trap as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 600mm X 450 mm (six hundred millimetre into four hundred fifty millimetre) bevelled edge mirror of superior glass mounted on 6mm (six millimetre)thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing high pressure PVC spigot and socket of Finolex make , waste and ventilating pipes ISI marked having 4 to 4.6 mm ( four to four point six millimetre) thickness including fixing with approved adhesive 100 mm (one hundred millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing high pressure PVC spigot and socket of Finolex make , waste and ventilating pipes ISI marked having 4 to 4.6 mm ( four to four point six millimetre) thickness including fixing with approved adhesive 75 mm (Seventy five millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing PVC 110x90mm (one hundred ten into ninety millimetre) dia floor trap of finolex of self cleaning design including fixing with approved adhsive, cost of cutting making the walls and floors etc. complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing PVC single equal branch plain of finolex including fixing with approved adhesive 100 mm (one hundred millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing PVC single equal branch plain of finolex including fixing with approved adhesive75 mm (seventy millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and laying PVC plain bend of finolex including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and laying PVC plain bend of finolex including fixing with approved adhesive etc. complete 75 mm (seventy five ) dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing PTMT liquid soap container 109 mm ( one hundred nine millimetre) wide, 125 mm ( one hundred twenty five millimetre) high and 112 mm ( one hundred twelve millimetre) distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. ( one hundred five grams) or dia as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 600mm X 20mm (six hundred millimetre into twenty millimetre) C.P. brass towel rail of continental series of Jaquar / contessa series of hindware/ ocean series of Cera complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 15 mm (fifteen millimetre) dia nominal bore. G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 15 mm (fifteen millimetre) dia G.I. pipes complete with G.I. fittings including trenching and refilling etc as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Making connection of galvanised steel distribution branch with galvanised mild steel main 20 mm to 40 mm (twenty millimetre to forty millimetre) nominal bore by providing and fixing tee including cutting and threading the pipes complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing C.P. brass bib cock of jaquar with 15 mm (fifteen millimetre) dia with capaston head as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 15 mm dia concealed CP brass stop cock of Jaquar all necessary fitting complete as per approved drawing, design & specification or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing brass full way valve with wheel 15mm (fifteen millimetre) nominal bore as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 15mm (fifteen millimetre) nominal bore uplasticised PVC connection pipe with brass unions as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and placing in position PVC water storage tank of SINTEX finolex ISI 12701 marked G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangment including hoisting upto all heights above ground level as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 15mm (fifteen millimetre) dia C.P. brass angle valve of Jaquar as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Constructing brick masonary chamber for underground C.I ( cast iron) inspection chambers and bends with common burnt clay building bricks in cement mortar 1:4 ( one cement is to four sand) including cover with frame (light duty) size 455mm x 610 mm internal diamention total weight of cover with frmae to be not less than 38 KG ( thirty eight kilogram) ( weight of cover 23 kg and weight of frame 15 kg) RCC top slab with 1:2:4 mix foundation concrete 1:5:10 inside plaster 15 mm thick with cement mortar 1:3 with a floating coat of neat cement on walls and bed concrete etctera complete as per approved drawing, design & specification or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or any other taxes imposed by the Government .

Providing and fixing PVC cowl of supreme/finolex make 160 mm (one hundred sixty millimetre) diametre as per approved drawing, design & specification or as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing 200 mm (two hundred millimetre) wide cast iron rungs with chequred or rubber non slip surface including fixing in man hole with 200 X 200 X 100 mm (two hundred into two hundred into one hundred millimetre) cement concrete 1:3:6 (one cement isto three sand isto six graded crushed stone aggreegate 20 mm (twenty millimetre) nominal size as per approved drawing, design & specification or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, Sale tax,GST or any other taxes imposed by the Government .

Supplying and fixing of cast iron medium duty 500 mm (five hundred millimetre) diametre cast iron cover with frame weight 38 Kg. ( thirty eight kilograme) as per approved drawing, design & specification or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or any other taxes imposed by the Government .

Narain Singh Thakur