REAPIRS TO BLDG NO P-43 (OR TRANSIENT LIVING) INCL BATHROOMS (TOILET BLOCK) AT BANIHAL AND PROVN OF UG CABLE 200 MTRS AND 01XREFIGERATOR (310 LTR) AT PATNITOP MIL STN UNDER GE (I) 873 EWS

Amount

Taking down cement plaster or cement line plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars, staging including taking out rooks from walls and separtion of serviceable material and disposal of unserviceable materials, debris and rubbish outside MD land omplete all as specified & directed.

Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan any radius, built in cement mortar 1:4 in half brick wall, complete all as specified.

Rendering 15mm thick in cement mortar 1:6 on other than fair face of brickwork or on one side of lathing, finished even and smooth without using extra cement, complete all as specified.

15mm thick plastering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement but using integral water proofing compound as per manufacturer,s instructions, complete all as specified. Note : Integral water proofing compound shall be measured & paid seprately.

Supply only integral water proofing compound, complete all as specifed.

Rendering 5mm thick in cement mortar 1:4 on other than fair face of ceiling/chajjas complete all as specified.

Prepration of new plastered surfaces of wall and applying two coats of oil bound distemper including one coat of alkali-resistant primimg paint and including two coat wall care putty complete all as specified and directed.

Preparation new plastered surfaces of walls and applying two coats of cement base paint including one coat of alkali-resistant primimg paint complete all as specified and directed.

Preparation old plastered surfaces of walls and applying two coats of cement base paint including complete removal of existing treatment all as specified and directed.

Prepration of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Demolition of stone slab and tiles of any description and thickness in floors, aprons etc laid and pointed in any mortar, and disposal of unserviceable materials, debris and rubbish outside MD land complete all as specified & directed.

Machine cut kota stone slab flooring, 18-20mm thick as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, laid over and including 20mm screed layer in cement mortar 1:3, rubbing, grinding and polishing to achieve mirror finish, complete all as specified.

Machine cut kota stone slab, 18-20 mm thick as per sample kept in GEs office as in vertical surfaces such as skirting/dado etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, laid over and including 10mm thick plastering in cement mortar 1:3, rubbing, grinding and polishing to achieve mirror finish, complete all as specified.

Dismantling plain or corrugated steel sheeting any gauge, thickness including nanital or similar pattern from roof covering or in ridges, hips, valley gutter and similar works complete, all as specified and directed.

Pre-painted galvalume aluminium zinc coating G.I based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering, fixed with self taping screws, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating G.I based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering / cladding to wall, fixed with self taping screws, complete all as specified and directed.

Dismantling wall & ceiling board (fibre, pulp, insulation etc.) or insulation boards / slabs/ blankets, any thickness, including cover fillets and disposal of unserviceable materials, debris and rubbish off the premises outside MD land omplete all as specified & directed.

6 mm thick non asbestos fiber cement plain building boards in false ceiling on and incl aluminium snap grid work 605 x 605 mm with using 36.5mm x 23.5 mm x 1.5 mm thick main tee, 23.5 x 23.5mm x 1.28 mm cross tee and 25x25x1.5mm angles fixed to perimeter of wall including necessary supporting Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store, removing debris and rubbish off the premises outside MD land omplete all as specified & directed.

Non-skid cermic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.11 Square metre but not exceeding 0.18 Square metre, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 10 mm thick in cement mortar 1:4 over 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone agrreagte) complete all as specified and directed.

Glazed ceramic coloured tiles in skirting/dado 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:4 as backing coat rough finished surface complete all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) n exc 1.5 sqm each, complete all as specified.

Pressed steel frames of size 125mmx60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, PCC for filling of hollow portion, complete all as specified

Mild steel framed works such as grills, framed guard bars, hold fast, clamps etc. and similar work including bending, cutting and welding as required, Fe. 290.Gde-E- 165 complete all as specified and directed.

PCC 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed block for hold fast and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.

Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated all as specified.

Factory made Glazed and skelton shutters 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without shash bars), size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated all as specified.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or stainless steel wire staples all as specified and directed.

Steel ventilator with top hung shutters including projecting type hinges with steel handle, and steel peg stay complete all as specified.

3mm thick sheet glass ordinary quality and glazing with oil putty / screws, in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified.

Factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) fixed in repair and directed.

Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-22, 75mm long, complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 200mm long (ISI marked), complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long (ISI marked), complete all as specified.

Extruded aluminium alloy handles, fabricated type, anodised of size 150mm and fixed, complete all as specified and directed.

Extruded aluminium alloy handles, fabricated type, anodised of size 125mm and fixed, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, 300mm long, all as specified.

300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) incl provision of cement concrte bedding, CI 'P' trap 100mm dia, connection to trap and fushing pipe, anti syphonage fixed in repairs complete all as specified and directed.

PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long, fixed in repairs complete all as specified.

Vitreous china urinal bowl type (Back or corner wall type) complete incl providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and incl 60mm long brass secrews, pointing around urinal in back in cement including fixing automatic cistern with brackets, flush pipe, grating and union for discharge pipe, fixed in repair complete all as specified and directed.

Vitreous china urinal partition white of size 410x330x160mm, 40cm above floor level fixed in repairs complete all as specified and directed.

Vitreous China, wash hand basin, flat back white of size 580mmx450mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, exclusive of waste pipe, chain and plug, porcelain stopper including cutting for and pinning in ends of brackets , complete all as specified.

Stop valve of cast copper alloy, chromium plated fancy type, concealed type (ISI marked), screwed down high pressure, screwed both ends for iron pipe or for unions 15 mm bore, fixed in repairs, complete all as specified and directed.

Pillar tap cast copper alloy with capstan head, fancy type, chromium plated (ISI marked), screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed shank and fly nuts screwed for iron pipe complete for 15mm bore pipe, fixed in repairs, complete all as specified and direct

Bib taps 15mm bore of cast copper alloy chromium plated (ISI marked) fancy type, screwed down, high presure, screwed both ends for iron pipe or for brass ferrule, fixed in repairs, complete all as specified and directed.

Stop /angle valve of cast copper alloy chromium plated (ISI marked), fancy type, screwed down high pressure, screwed both ends for iron pipe or for unions 15 mm bore, fixed in repairs, complete all as specified and directed.

PVC connection 15mm size with length 600mm with PTMT nuts complete all as specified and directed.

32mm bore PVC flush pipe for low level cistern complete all as specified & directed.

Grating square 150mm size of PTMT (minimum weight 100 gms), complete all as specified

PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, dia of outlet 75mm, complete all as specified.

Towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges, complete all as specified.

Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats fixed in repairs complete all as specified.

Brass chromium plated shower rose 125mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified & directed.

Disconnecting existing tank 500 - 1000 ltr & removing to store all as specified and directed.

Rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 1000 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and PTMT ball valve 20mm (Minimum weight 210 gms), high pressure with polyethelyne float and fly nuts complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified.

15mm dia GI steel water tubing, medium grade ISI marked, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors complete all as specified.

20mm dia GI steel water tubing, medium grade ISI marked, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors complete all as specified.

Dismantling of 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified.

PVC (SWR) pipes, 110mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified & directed.

PVC (SWR) pipes, 75mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors/weep holes, complete all as specified & directed.

110mm bore PVC (SWR) bends any radius, complete all as specified.

75mm bore PVC (SWR) bends any radius, complete all as specified.

75mm bore PVC (SWR) vent cowl complete all as specified.

Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed.

Preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified.

Demolition of reinforced cement concrete kitchen slabs/shelves of any description in any position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition), complete all as specified.

TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified & directed.

RCC 1:2:4, type B-1 using 20mm graded crushed stone aggregate as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Formwork to sides and soffits of roof slab not exceeding 200mm thick for rough finished surfaces of concrete, complete all as specified and directed.

Granite (of any type) tiles 20mm thick, machine cut,in kitchen plateform and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting & polishing, laid over and including 15mm screed layer in cement mortar 1:4, complete all as specified & directed.

Granite (of any type) tiles 20mm thick, machine cut,in skirting/dado and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting & polishing complete all as specified & directed.

Demolition of cement concrete in ground floors and paving not exceeding 15cm thickness (below or above ground level) un-reinforced and disposal of unserviceable materials, debris and rubbish off the premises outside MD land omplete all as specified & directed.

Plain Cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed.

75 mm thick plain cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in plinth protection, and laid in panels complete and finished the even & fair all as specified and directed.

Forming construction joints 30mm deep x 10 mm wide filled and sealed with sealing compound, Grade ‘A’ complete all as specified & directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar and disposal of unserviceable materials, debris and rubbish off the premises outside MD land omplete all as specified & directed.

Concrete bed to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid in cement concret 1:4:8 (Nominal mix) type D-2 using 40mm graded stone aggregate, and tested, complete all as specified & directed.

Salt-glazed stoneware drain pipe, internal dia of pipe 150mm, laid in trenches and jointed and tested, complete all as specified including taking down old unservicable pipes.

Taking out carefully copper / aluminium point wiring, (Light, fan, socket or power) complete with all fitting, fixtures such as switch, ceiling rose, pendents, regulators, sockets, light fitting holder, regulator, MCBs, DB's etc. for taking credit including making good the disturbed surface of wall/floors, complete all as specified and directed.

Taking down old and userviceable sub main wiring of any size /type/core included earth wire complete with batten / conduit including making good the disturbed surface complete all as directed.

Taking down old and userviceable distribution board of any type /way/capacity including all type of controls complete after removing all connection including making good the disturbed surface complete all as directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including concealed PVC conduit of wall thickness not less than 1.8mm and accessories of suitable size for concealed wiring including 1.50 Sqmm copper earth wire (green colour) FRLS Cable for one light point or fan point or bell point controlled by one No, one way switch/one bell/buzzer point using cable of different insulation colour for colour coding including modular white cover plate with frame for mounting modular switches, sockets, fan regulator etc including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 93 here-in-before but for for one light point controlled by two way switch complete all as specified and directed.

All as per the description of Serial Item No 93 here-in-before but for one 3 pin socket outlet 5 Amp independent, complete all as specified and directed.

All as per the description of Serial Item No 93 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and directed.

All as per the description of Serial Item No 93 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 2.5 Sqm with 2.5 Sqmm copper conductor in green colour for as earth continuity conductor all as specified and directed.

Modular switch 1 way 6A, 1 module, complete all as specified and as directed. (Make : Havells (Crabtree) cat No. ACVSXXW101 or equivalent make Indo Asian / HPL)

Modular switch 1 way 16A, 2 module, complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACVSXXW161 or equivalent make Indo Asian / HPL)

Modular switch 2 way 6A, 1 module, complete all as specified and as directed. (Make : Havells (Crabtree) cat No. ACVSXXW162 or equivalent make Indo Asian / HPL)

Modular Socket, 6A, 2/3 pin combined 2 module, complete all as specified and as directed. (Make : Havells (Crabtree) cat No. ACUKXXW063 or equivalent make Indo Asian / HPL)

Modular Socket 6A/16A, 2/3 pin combined 2 module, complete all as specified and directed.(Make : Havells (Crabtree) cat No. ACUKCXW163 or equivalent make Indo Asian / HPL)

Modular Fan regulator, dimmer type, 120 Watt , 2 module, complete all as specified and as directed. (Make : Havells (Crabtree) cat No. ACVDEXW042 or equivalent make Indo Asian / HPL)

Modular cover plate, 1 module, complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACVPPCWV01 or equivalent make Indo Asian / HPL)

Modular cover plate, 2 module, complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACVPPCWV02 or equivalent make Indo Asian / HPL)

Modular cover plate, 3 module, complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACVPPCWV03 or equivalent make Indo Asian / HPL)

Modular cover plate, 4 module, complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACVPPCWV04 or equivalent make Indo Asian / HPL)

Modular cover plate, 6 module, complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACVPPCWV06 or equivalent make Indo Asian / HPL)

Modular cover plate, 8 module, complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACVPPCWV08 or equivalent make Indo Asian / HPL)

Modular surface mounting plastic box of size 3x3, 1/2 module complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACNXMIZX01 or equivalent make Indo Asian / HPL)

Modular surface mounting plastic box of size 4x3, 3 module complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACNXMIZX03 or equivalent make Indo Asian / HPL)

Modular surface mounting plastic box of size 5x3, 4 module complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACNXMIZX04 or equivalent make Indo Asian / HPL)

Modular surface mounting plastic box of size 6x3, 6 module complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACNXMIZX06 or equivalent make Indo Asian / HPL)

Modular surface mounting plastic box of size 8x3, 6 module complete all as specified and directed. (Make : Havells (Crabtree) cat No. ACNXMIZX08 or equivalent make Indo Asian / HPL)

Ceiling rose surface bakelite three terminals 240 volts complete all as specified and directed.

Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings complete all as specified and as directed.

LED Lamp 230 volt 09 watts, in white colour with maximum Lumen output (850 lm) and colour temp 3000 K with base cap B-22, complete all as specified and as directed. Make : Havells / Crompton Greaves / Philips /Syska/ Wipro

LED light fitting 1x20 watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up cable of copper conductor size 3-core, 23/0.0076 from ceiling rose to light fitting connector complete including taking down old fitting all as specified and directed. Make :- HAVELL's Cat No UMILINE+BS20WLED840SPCSS or equivalent in Crompton /Syska/ wipro

Bulk head light environmental friendly, ultra-modern, energy saving, surface mounted, decorative hexagon bulkhead back-lit LED luminaries complete with all accessories suitable for and including 1 x 10 Watts LED lamp including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 Volts 50 Hz, IP 65 complete all as specified and as directed. Make : Havells Cat Part No HEXAFT10WLED857SSYMBOPC or equivalent in Crompton /Syska/ wipro

Sub main wiring with two single core PVC insulated multistranded un-sheathed FRLS cable of size 2x4.0 Sqmm with stranded copper conductor,1100 volts grade drawn through and including PVC conduit (including all conduit accessories) concealed in waals /roofs/floors with continuous PVC insulated multistranded unsheathed FRLS cable earth wire of 1x2.50 Sqmm dia complete all as specified and directed. Note : Two run of 4.0 Sqmm wire, one run of 2.5 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

Sheet metal enclosure factory made single door for DB 240 volts with 200 Amps rated bus bar SPN 12 Way sheet metal powder coated, IP42 protection complete all as specified and directed.

Sheet metal enclosure factory made, vertical type, double door for TPN, 415 Volts, 50 Hz, sutable for FP for fixing MCCBs and MCBs, DB 12 ways, metal powder coated indoor type, IP43 protection complete all as specified and directed.

MCCB TPN 100Amp 16 KA 415 Volts, thermal release type complete all as specified and directed.

MCB SPN 40 Amp 10 KA 240 Volts, 'C' Series, complete all as specified and directed.

MCB SP 5 to 32Amp 10 KA 240 Volts, 'C' Series, complete all as specified and directed.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 Part-I, connected to test point complete, all as specified and testing on completion.

Exhaust fan PVC body with louvers of size 300mm sweep, 900 RPM, 230 volts (single phase) complete with bolts, nuts & washers, embedded in the wall including provisioning of three core flexiable copper cord of size 23/0.0076 of required length from ceiling rose or connector to Exhaust fan for connection, complete all as specified & directed

XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade ISI marked cross sectional area 25 Sqmm 3.5 core on wall including taking down old cable, complete all as specified and as directed.

BLANK

BLANK

Excavating in trenches, not exceeding 1.5metre wide and not exceeding 1.5metre depth for foundation, etc., and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick any type of soil, complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Sand cushioning to underground cables using new dry river sand laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete, punned to 18cm, complete all as specified and directed Note : Punned thickness of 18cms shall be measured for payment.

Supply and laying brick covering with width equal to length of bricks as mechanical protection to underground cable using old size sub class 'B' bricks, laid flat size 230mm x 115mm x 75 mm with width of brick perpendicular to length of cable, all as specified and directed.

XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade ISI marked cross sectional area 50 Sqmm 3.5 core on wall including taking down old cable, complete all as specified and directed.

Horizontal Boring by Passing GI Protection Pipe up to 50mm Bore (dia), under Road/Foot Path, not exc 10.00 Metre in a Single Length, complete all as specified and directed.

Galvanised tubing light grade, 40 mm bore laid in trenches or under ground/floor or road of fixed with pole for protection of cable including GI clamps with bolts nuts and washers complete all as specified and directed.

Sheet metal enclosure factory made, vertical type, double door for TPN, 415 Volts, 50 Hz, sutable for FP for fixing MCCBs and MCBs, DB 8 ways, metal powder coated indoor type, IP43 protection complete all as specified and directed.

MCCB FP 100Amp 16 KA 415 Volts, microprocessor based complete all as specified and directed.

MCB TPN 63 Amp 10 KA 415 Volts, 'C' Series, complete all as specified and directed.

Supply, installation, designing, testing and commissioning of self supporting totally enclosed double door at front, LT feeder pillar compartmentalised design, dust and varmin proof of size 600 mm (Height) x 600 mm (Length) x 450 mm (Width) suitable for 440 Volt 3 pahse 4 wire system made out of 3.15 mm thick CRCA sheet and built upon regid frame work having front and rear hinged doors with neoprence rubber gasket including danger piate, earthing strip point and, ventilation louvers at tehreat side, bottom detachable gland plate complete with suitable size of Zinc/Cromium plated and nuts, bolts and washers etc. The pannel shall be synthetic enamelled painted and the control circuit diagram shall be with colour code solid conductor copper 1.5 sqmm cabel for easy identification including incomming/outgoing cable holes at the bottom, complete after taking down the old unserviceable one. The Panel shall be emmbeded with 75 x 6mm MS Angle Iron frame and to be grouted with PCC foundation (1:2:4) type B2 upto a height of 50 cm from normal ground level complete all as specified & directed and comprising of the following fitments:-

(a) Aluminium bus bar 200 amps -04 Nos, suppported with suitable size of heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour code (red, yellow and blue) for.(i) MCCB 160 Amps, breaking capacity 25 KA, FP, 415 Volts (adjustable thermal and magnetic release) – 01 No (ii) MCB TPN 40 Amps – 02 Nos (ii) MCCB 63 Amps, breaking capacity 16 KA, FP 415 Volts (adjustable thermal and magnetic release) – 02 Nos (iii) Lock pedestal – 01 No Indicating Devices. (a) LED indicating lamps for Main Supply indicating 'R', 'Y', 'B' - 01 Set of 3. (b) Digital Voltmeter (Make AE/L&T) - 01 No. (c) Current Transformer having Ratio 400/5, 15 VA - 01 Set of 3. (d) Digital Ammeter (Make (AE/L&T) - 01 No.

Make of Panel : DV Electromatics Private Limited / Simon Fabricators / Electricfield Co / Adhunik Switchgear / Universal Switchgear Make of MCCB : L&T / Legrand / Schneider / Havells Make of Voltmeter / Ammeter / Multifunction Meter : SECURE / L&T (RISHAB) / C&S ELECTRIC / MECO

Regrigerator, electric driven (single phase), capacity of 308-315Liters BEE 3-5 star rated, covertible with smart inverter compressor, door cooling complete all as specified and directed. (Make LG Product No GL-T322SPZX or Samsung / Godrej / Whirpool / Voltas)

Voltaze stabilizer for automatic operation single phase naturally air cooled indoor type & designed for input variation between 170 Volts to 250 Volts with output voltage stabilized at 230 Volts with accuracy of + 2.5% and capacity of 2KVA complete all as specified and directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including PVC casing and capping and accessories of suitable size including 1.50 Sqmm copper earth wire (green colour) FRLS Cable for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, existing mild steel sheet or cast iron boxes including making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 147 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 2.5 Sqm with 2.5 Sqmm copper conductor in green colour for as earth continuity conductor all as specified and directed.

Switch piano, flush type, 5 Amps, single pole, one way, complete all as specified and as directed.

Switch piano, flush type, 15 Amps, single pole, one way, complete all as specified and as directed.

KOHLI CONSTRUCTION CO

M/S maqsood enterprises

Bidder Name

M/S maqsood enterprises

KOHLI CONSTRUCTION CO

M/S BILAL AHMED WANI