Repair and Renovation of Residential Quarter of Naib Tehsildar Hiranagar. Under Capex Budget 2021-22 (NFB)

Amount

Labour to be engaged for clearance of site and removing of unhygenic mulba including disposal of the same before execution of work.

Labour charges for carpenter/plumber or equilvalent type.(Per day)

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material incl. lead and lifts as per direction of Engineer-in-charge.

Demolishing brick work in cement mortar manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material incl. all leads and lifts as per direction of Engineer-in-charge

Dismantling doors, windows and clerestory windows of area 3.00 sqm and below (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking ,all leads & lifts.

Removing mortar from bricks and cleaning bricks including stacking all leads and lifts. (stacks of cleaned bricks shall be measured) from brick work in cement mortar

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints & preparing & plastering the surface of the walls complete including disposal of rubbish to the dumping ground with cement mortar 1:4 (1 cement : 4 coarse sand) incl all leads and lifts

Regrading terracing of mud phaska covered with tiles or bricks, in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement: 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded) all leads and lifts

Providing gola 75 x 75 mm in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 10mm down gauge) incl. finishing with cement mortar 1:3 ( 1 cement : 3 fine sand) as per standard design in 75 x 75 mm deep chase incl. all leads, lifts & carriage of material by MT/ H.L.

Making Khurras 45 x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 Coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 m x 1m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges, making and finishing the outlet complete incl. all leads, lifts & carriage of material by MT/ H.L.

Providing and laying 400 micron thick transparent PVC sheet on roof under mud phaska cutting placing complete job.

Earth work in all kinds of soil excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms including getting out excavated earth and disposal of surplus excavated earth as directed incl. all leads, lifts & carriage of material by MT / H.L.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L.

Providing and laying in position cement concrete of specified grade incl. curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone agg. 20 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Cold twisted bars incl. all leads, lifts & carriage of material by M.T./ H.L.

Centring and shuttering including strutting propping etc and removal of form work for:-

Foundations, footings, bases of columns etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platforms.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth including all shapes, leads, lifts and carriage of material by MT / H.L. in cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level upto floor V level (By manual means) incl. all leads, lifts & carriage of material by M.T. H.L.

Half brick masonry with bricks of class designation 75 in foundations and plinth in cement mortar 1:4 ( 1 cement :4 coarse sand) incl all leads, lifts and carriage of material by MT / H.L.

Extra for half Brick masonry in superstructure above plinth level upto floor V level incl all leads, lifts and carriage of material by MT / H.L.

6 mm thick plaster to ceiling of mix 1 : 3 ( 1 cement : 3 fine sand) incl. all leads, lifts and carriage of material by M.T / H.L.

Renewing glass panes and re-fixing existing wooden fillets Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without drain board 610x460mm bowl depth 200mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete. Semi rigid pipe 40 mm dia

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diametre

Providing and fixing PVC Panelling in Partition/doors of approved quality as per the direction of Engineer- in - Charge (Complete job)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work.

Painting with synthetic enamel paint of approved brand & manufacture of required colour to give an even shade, one or more coats on old work

Finishing walls with water proofing cement paint of required shade: old work (one or more coats applied @ 2.20 kg/10sqm)complete

P/F aluminum work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required incl. cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)For fixed portion Powder coated aluminum (minimum thickness of powder coated 50 microns)

P/F aluminum work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required incl. cleat angle, Aluminum snap beading for glazing/panelling, C.P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)For shutters of doors, windows & ventilators incl. providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.)Powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in- charge. (Cost of aluminum snap beading shall be paid in basic item.) With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

Providing and fixing ACP sheet panelling 4.0 mm thick in Partition/doors of approved quality as per the direction of Engineer- in-Charge (Complete job)

Providing and fixing Anodized aluminum grill (Anodized transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved Anodized aluminum standard section around the opening, all complete as epr requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment)

Providing and fixing aluminum sliding door bolts 300x16 mm ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminum tower bolts SI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles 125 mm ISI marked anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc complete

Providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete.With Galvanized M.S. Wire gauge with wire of dia 0.63 mm with 12 mm mild steel U beading

Supply of common burnt clay (non modular) brick tiles of class designation 10.0 for regrading terracing of mud phaska incl. all leads and lifts.

Kewal Krishan

M/S DWARKA NATH GOVT CONTRACTOR

NARINDER CONTRACTOR

M/S KULJEET SINGH

M/S PARDEEP JAMWAL GOVT CONTRACTOR

YASHPAUL SINGH RATHOUR