REPAIR MAINT TO LEAKAGE SEEPAGE JOINERY WORKS FLOORING WIRE MESH WINDOW GLASS PANES PAINTING PLINTH PROTECTION AND OTHER MISC B R WORKS

Amount

Material and labour for Water proofing treatment of existing roofs as per details given below after complete removal of existing water proofing treatment and expose of top surface of RCC slab of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with water and using wire brush including removing debris to outside the MOD land complete all as specified and as directed :-

(a) Dismantling existing cement concrete/ roof tiles on roof including removing debris to outside MOD land as directed.

(b) Bring up to the slope by providing PCC 1:2:4 type B1 using 20mm graded stone aggregates of average thickness of 50 mm.

(c) Rendering 10mm thick in CM 1:3 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing water proofing compound as per manufacturer’s instructions.

(d) Surface should be free from any loose paint, dust or grease. Remove all existing bitumen coatings completely by using intense wire brushing, high speed water jet & vacuum cleaner for thorough cleaning of the surface to avoid ‘Peeling off’ problems.

(e) All cracks at corner joints, channels and parapets should be properly treated. For filling cracks up to 3mm crack seal material of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical to be used. Bigger cracks, damaged portions & hollow areas must be repaired with polymer modified cement mortar.

(f) Apply a coat of self priming smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical with 33% dilution with water using brush/roller on newly plastered surface after curing as per IS-456 and allow to dry for 4 to 6 hours (dilution & forced coverage requirement strictly as per manufacturer’s instructions).

(g) After the primed surface has dried, apply first coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical using brush/roller on the same primed surface & allow to dry for 4 to 6 hours.

(h) Prepare for apply 2nd coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical using brush/roller on the same surface. The temp to be maintained 25 to 35° C through out the all above application work.

(j) In case of severe dampness an additional coat of damp proof materials to be applied.

Note for item No 01 to 10:- (i) The work shall be carried out through authorized and qualified applicators of the following manufacturers only. MOU to be submitted before commencement of work. Make : M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical

(ii) A performance guarantee certificate for 10 years shall be submitted by the contractor to the GE on completion of work as specified.

(iii) The unit quoted rate is deemed to include taking down of water pipeline, tanks, wires (etc) found on roof and refix at the original position after complete treatment of roof.

(iv) The unit quoted rate shall be inclusive of material, all labours, tools and plants including scaffolding required for working up to approx 7.5 mtr height from natural ground level.

(v) The unit rate quoted for item is deemed to include for Removing of accumulated earth of any width and depth up to 15 cm cleaning/cutting the grass with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from plinth protection to outside MD land.

(vi) Adoption of necessary safety arrangement like safety belts, ropes, helmets, netting etc. which are required for safety of working labour at height exceeding 3 to 25 mtr height shall be mandatory and deemed to be included in the unit rate quoted.

Taking down cement plaster on brick or stone walls, or concrete walls or ceilings etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises and leaving the work clear of any plastering and Material and labour for Rendering 15 mm thick in two layers on brick or stone or concrete surfaces, first coat 10mm thick in cement mortar 1:4 and 2nd coat 5mm thick in cement mortar 1:4 mixed with water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete all as specified and directed. Note :- (a) Water proofing compound shall be measured and paid separately. (b) The unit rate quoted is deemed to include for removal of accumulated earth of any width and depth up to 15 cm cleaning/cutting the grass with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from plinth protection to outside MD land.

Supply only water proofing compound

Material and labour for preparation of newly plastered surfaces wall/ ceiling and applying three coats of white washing on ceiling/ walls surfaces complete all as specified and directed.

Material and labour for applying two coat of cement based paint over a coat of primer, including preparation of newly plastered wall surfaces of any description, complete all as specified and as directed.

Material and labour for Repair to ends of chajjas/ parapets by removing old concrete, loose material & cleaning of the reinforcement and finishing the surface with rich cement mortar 1:3 , finished fair & even and making good (not exc 3Sqm) with existing finishes complete all as specified and as directed. Note: Rate quoted by the tenderer shall be deemed to inclusive of double steel scaffolding.

Taking down chowkhat or frame(wooden/steel) exceeding 1.50 Sqm not exceeding 4.0 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

Taking down shutters of any description exc 1.0 Sq.m and n.exc 2.0 Sq.m each complete all as specified and directed.

Cutting holes in stone wall exc half brick and n.exc one brick in cement mortar for inserting hold fasts/lugs and making good dismantled portion in cement mortar 1:3 or 1:2:4 type B-1 concrete as required complete all as specified and as directed.

Supply and fixing MS work (flat iron) 25mm x 3mm thick) in small articles such as hold fast and similar smaal articles conforming to Fe 290 Gde E-165 including taking down existing one complete all as directed.

Material and labour for Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Supply and Fixing 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, commercial type on both faces complete all as specified and directed.

Supply and fixing Factory made 35mm thick Glazed and skeleton shutters/windows, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

Preparation of new wood or wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, and fixed complete all as specified and as directed.

Supply and fixing 200 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing Aluminium handles cast type anodised 200 mm long complete all as specified and as directed.

Supply and fixing 250mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

Supply and fixing Floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete including taking down existing one all as specified and as directed.

Supply and fixing Plain fillets, square, rectangular or triangular in section, clean sawn, se-cured with nails or brads in section area 6 sq.cm but not exc 13 sq cm including taking down existing one complete all as specified and as directed.

Taking down chowkhat or frame(wooden/steel/Alumnium) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

Supply and fixing in Steel windows with side hung shutters including projecting type hinges, frame with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Supply and fixing 4 mm thick sheet glass ordinary quality and glazing complete in square n exc 0.50sqm each complete all as specified and directed.

Supply and fixing frosted glass 4.0mm thick, pin head type n exc 0.5 sq.m in each pane and fixed. complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified .

Supply and fixing Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified.

Supply and fixing Butt hinges 75 mm long medium weight cold rolled stainless steel complete all as specified and as directed.

Supply and fixing 150 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing aluminium handles cast type anodized 150 mm long complete all as specified and as directed.

Material and labour for Vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer, 15 mm thick in Cement Mortar 1:6 complete including dismantling of existing tile and disposal of to outside MD land all as specified and as directed.

Material and labour for Vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer ,15 mm thick in Cement Mortar 1:6 complete including dismantling of existing tile and disposal of to outside MD land all as specified and as directed.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, star lock, included rubber beading all complete as per architectural drawings and the directions of Engineer-in-Charge.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, star lock, included rubber beading all complete as per architectural drawings and the directions of Engineer-in-Charge.

Supply and fixing in aluminium anodised grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design/pattern(DG 104), with approved standard section and fixed to existing window frame with CP brass/stainless steel screw not less than 50mm and @ 200mm c/c, incl cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alum standard section ( 28mm x 19mm x 2mm thick)around the opening, all complete as per requirement and direction of EIC.

Supply and fixing aluminium louvers with levers and locking arrangements suitable for fixing 100mm wide 4 to 6 nos frosted glass complete all as specified and directed

Supply and fixing in repairs 200 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing Floor in repairs door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete including taking down existing one all as specified and as directed.

Supply and Fixing in repairs 250mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, fixed in repair to wooden frame/welded to metal frame complete all as specified and as directed.

Supply and fixing in repairs aluminium handles cast type anodised 200 mm long complete all as specified and as directed.

Supply and fixing in repairs 250mm, ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and fixing Aluminium body door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to1000 mm in width and of weight between 61 to 80 kg and fixed including taking existing one complete as directed by Engr-in-charge.

Supply and fixing in repairs MS Mortise lock, 4 levers vertical type, size 100 mm and all as specified and directed

Supply and fixing 5mm thick rubber beading strips of entrance doors having width exc 3cm to not exc 5cm to arrest entry insects including taking down existing one complete all as specified and as directed

Material and labour for Applying silicon sealant on joints of wall,cill jambs roof etc complete all as specified as directed

Material and labour for Petty repair to Aluminum/glass doors, windows, ventilators, partitions and making good the same size up to 2 Sqm (i.e. included change Handles, hinges, star lock, rubber beadings, bottom bearing, clips etc) included taking down and refixing complete all as specified and directed.

Material and labour for Petty repair to wooden door, Skelton door, PVC door, wooden window, wooden ventilator, cupboard door, wardrobe door with shutter (size up to 2 Sqm) including roller, windows, etc with minor repair and easing and adjustment/alignment to operable with accessories if required any ( like roller of cupboard door, butt hinge, handle, tower bolt, beading, bow handle, etc. complete)included taking down and refixing complete all as directed.

Taking down MS window shutters n. exe 1.5 sqm through cutting of existing any type of hinges, handle and tower bolt and fixing new box type hinges, MS handle and MS tower bolt the same window by welding. The quoted rates shall be included the following aspect:- (a) Cutting of existing piano hinges, handle and tower bolt from window frame and shutter. (b) Fixing of removed shutter in the same frame on MS box type hinges 100mm, MS handle 100mm and MS tower bolt 100mm by welding. (c) Easing and adjusting the shutter before re-fixing if found required. (d) Finishing the window frame and shutter with two coat of enamel paint. (e) Necessary scaffolding material to be included as the building height is more than 10mtr. Note : Box type hinges, handle and tower bolt will be measured separately as supply only and labour element is deemed to be included in this item.

Supply only MS Box type hinges 50mm.

Supply only MS Handle 100mm.

Supply only MS tower bolt 75mm

Supply and fixing in repairs Stainless steel peg set of having 5 pegs powder coated fixed to wall surface with pvc plug and screw complete including taking down all as specified and as directed.

Supply and fixing False ceiling using GI snap grid size 60x60cm with main runner 38x24,wall angle & cross tee 29x24mm wall angle 24x24mm suspended with 4mm dia GI Wire fixed with steel dash fasteners carrying max load up to 8.1 Kg/Sqcm with 4mm thick designer ceiling board (Lake & Hill) all as per Everest regular T-2430 or equivalent (Make-Ramco/Charminar/Armstrong) including dismantling all as specified and as directed.

Material and labour for Providing and injecting chemical for post constructional Anti Termite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same all as specified and directed.

Supply and fixing in repairs bottom/top rail 300 mm wide of second class hard wood 35 mm thick including making of grooves and fixing new bottom rail using fevicol and wooden pinning and treated with two coats of synthetic enamel painting over one coat of pink primer complete all as specified and directed by Engr-in-charge.

Supply and fixing in repair wooden pelmet boxes/curtain rods in position by using rawl plugs/wooden gutties fixed with MS holder clips complete incl tightening of screws etc complete in all respect length of each pelmet n exc 2.50 mtr long complete all as specified and directed.

Supply and fixing in repair Stainless Steel Door Magic Eye with Flap to wooden doors , unique design any type complete all as specified and directed

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete including taking down existing one all as specified and directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size exc 0.09 Sqm but n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) complete all as directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and Material and labour for Glazed ceramic coloured tiles 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as skirting/ dado including 10mm thick 1:3 backing coat complete all as specified and directed.

Material and labour for Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and Material and labour for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass not exc 0.5 sqm each pane complete all as specified and directed.

Material and labour for Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and Material and labour for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass exc 0.5 sqm each pane complete all as specified and directed.

Supply and fixing Sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repairs all as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA.

Supply and fixing Plate rack of size 65 cm x 96 cm made of stainless steel fixed in repairs complete all as specified.

Supply and fixing in repair looking mirror 3 mm of size 600mm x 450mm on commercial ply wood 6mm thick with PVC/ wooden moulding beading fixed to wooden plugs with chromium plated brass, screws and cup, washers, aluminium frame and fixed complete all as specified and directed.

Supply and fixing PVC body cabinet box mirror of size 350mm X 450mm X 10mm PTMT alloy of approved pattern and design including taking existing one complete as directed by Engr-in-charge.

Material and labour for 25mm dia mild steel powder coated drapery rod out to length required without joint in between and fixed at openings including taking existing one complete as directed by Engr-in-charge.

Supply and Fixing in repairs Mild steel powder coated fancy type brackets fixed at both the end of drapery rod of same colour and type of drapaery rod as directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat oil bound distemper complete all as specified and as directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, chajja,ceiling, balcony, facia etc., brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent, trading, oil, greasy spots and applying one coat of white wash complete all as specified and directed.

Material and labour for Preparation of old plastered surfaces of wall by using pressure washer, removal all dirt and dust and applying one coat of exterior emulsion weather proof paint complete all as specified and as directed. Note:-(i) Cost of scaffolding required deemed to be included in the quoted rate of item and nothing extra shall be admissible on this account.

Material and labour for Preparation of old painted wooden surface of any description and applying one coats of synthetic enamel paint using mechanical means, not otherwise described over 10 cm width or girth, complete all as specified and directed.

Material and labour for Preparation of old painted surfaces of steel and applying one coat of synthetic enamel paint using mechanical means over 10 cm width or girth, not other wise described complete all as specified and as directed.

Material and labour for Preparation of old decorated surfaces of walls by using pressure washer, remove all dirt & dust ,applying one coat of wall care putty and then and applying two coats of premium oil bound distemper over one coat of primer as per manufacture instruction of required shade complete all as specified and directed by Engineer - in - Charge. Note:-(i) Cost of scaffolding required deemed to be included in the quoted rate of item and nothing extra shall be admissible on this account.

M & L preparation old surfaces of exterior wall decorating and water proofing treatment to wall surface by wire brushing in order to remove dust, dirt, loose particles, laitance. Thereafter wash the surface with clan water & allow to dry. Fill visible cracks/ joints by chemistic crack sealer caulking compound & allow to dry for 24 hours. Apply a primer coat of roof guard prime M Seal (water base primer) and allow to dry for 6 hours. Thereafter apply 02 coats of Weather coat ( high build anti carbonating coating cum waterproofing) & shade by brush at the interval of 08 hours between the coat and allow to dry to match the existing shade including necessary scaffolding for any height, covering etc complete all as per specified and directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat of cement based paint complete all as specified and as directed.

Material and labour for Preparation of old concrete/Asbestos/Cement/Plaster surfaces over brooming down or steel wire brushing down and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for Plain cement concrete (1:3:6) type C1 (20 mm graded stone aggregate), 75mm thick, as in plinth protection courses, top surface of concrete finished even and smooth with out using extra cement, including expansion joint 10mm thick filled with mastic filling comprising of 01 part of heated blown bitumen and 3 parts of sand including demolition existing cement concrete including disposal of demolition material up to MD land complete all as specified and directed by Engineer- In - charge

Material and labour for 25 mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in flooring surface and smooth without using extra cement including demolition existing cement concrete, including disposal of demolition material up to MD land complete all as specified and directed by Engineer- In - charge

Material and labour for 18/19mm thick Prelaminated particle board, interior Grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work including taking down complete all as specified and as directed.

Supply and fixing 40 mm dia cupboard knobs fixed with nut, screw and washer of brass polished complete including taking down existing one all as specified and as directed.

Supply and fixing Continuous (piano) hinges, stainless steel bright finish or electro galvanised of 40mm width of flaps (when open) complete including taking down all as specified and as directed.

Supply and fixing Magnetic catches with 8mm dia steel ball and brass body and striking plate including taking down in complete all as specified and directed.

Material and labour for 6 mm thick teak wood lipping for 18/19 mm thick particle board fixing with nails complete including taking down all as specified and as directed.

Material and labour for in repairs 300x300x25mm thick prepolished cement concrete chequered tiles jointed in neat cement slurry and pointed in white or coloured cement to match the floor and including 20mm thick screed bed in CM 1.4 and incl removal of old and necessary demolition and all as specified and directed by Engr-in-Charge.

Material and labour for PCC (1:4:8) type D2 using 40mm graded aggregate 75mm thick as in sub base of floor finished even and rough to receive top layer and all as specified and directed and Demolition of Concrete (un reinforced) of any description and in any position not otherwise specifically provided.

Supply and fixing in repair aluminium anodized hasp and staples safety type with mild steel hinge pin incl bolt to hinge plate fixed with screws of 100mm length complete all as specified and as directed.

Supply and fixing Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved including taking down existing one complete all as specified and as directed.

Petty repairs to refixing the existing Wash hand basin and Sinks made of stainless steel 1mm thick kitchen flat back with including fixing cantilever CI/Angle iron brackets embedded in concrete block including connecting waste coupling 32mm bore, including bedding, waste fitting, waste pipe in cement mortar on to dwarf wall and connecting union to pipe, filling gap in white cement and all necessary fittings to fixed in repair (including taking and refixing the same position) complete all as directed.

Supply and fixing Vitreous china squatting pan 'Orissa' Pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe ) including provision of lime concrete bedding fixed in repairs all as specified and as directed.

Supply and fixing in repairs Bib taps fancy type chromium plated with crutch or butterfly handle screwed down screwed for galvanised iron pipe or for brass ferrule and fixed complete for 15 mm bore all as specified and as directed.

Supply and fixing Wash basin vitreous china (flat back and angle back Type) size 580x400mm including taps waste chain and plug and porcelain stopper but brackets including cutting for and pinning in ends of brackets or erecting stand with waste pipe ,fixed including taking taking down existing one complete as directed by Engr-in-charge.

Supply and fixing Rotational moulded polythene water storage tank of 1000 Ltrs capacity (three layer white colour) cylindrical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down of old unserviceable tank complete all as specified and directed.

Supply and fixing in repairs 20mm dia gun metal gate valve with iron wheel screwed both ends for iron pipe and all as specified and directed.

Supply and fixing Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including taking down existing one complete all as specified and as directed.

Supply and fixing CP Concealed stop cock, Regular body with adjustable wall flange screwed down screwed for iron pipe 15mm bore including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in repairs Overhead Shower rose ø125mm (Brass Chrome Plated) complete all as specified and as directed.

Supply and fixing Angular stop cock, valves high pressure screwed both ends iron pipe or for unioins 15mm dia, including taking existing one complete as directed by Engr-in-charge.

Supply and fixing in repair Brass Chromium plated wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed .

Supply and fixing in repair Toilet paper holder box type of vitreous china fixed to walls with chromium plated (CP) brass screws and complete all as specified.

Supply and fixing in repair PVC Dual flush ceramic colour cistern , low level, 10 litres capacity, star white with inlet float ball valve, PVC flush pipe and handle, making proper fixing and hanging arrangements (Make: /Parryware/Hindware/ Cera) all as specified and as directed.

Supply and fixing in repairs CP 2 way bib cock with wall flange fancy type screwed down screwed for iron pipe in repairs 15mm bore complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in repairs 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, screwed for iron pipe complete as directed by Engr-in-charge.

Supply and fixing in repairs plastic water closet seat cover white or tinted, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinge device and including taking existing one complete as directed by Engr-in-charge.

Supply and fixing in repairs of chromium plated tubular towel rail 20 mm dia brass D type 60 cm long between flanges complete all as specified and as directed.

Supply and fixing Glass self assembly including taking existing one complete as directed by Engr-in-charge all as specified and as directed.

Supply and fixing in repairs of Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight15mm-90gms) and directed by Engineer in Charge.

Supply and fixing in repairs 40 mm Waste coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed one complete all as manufactures and all as specified

Supply and fixing 150 mm dia round/square grating of CP with or without hole including Jointed to PVC pipe complete all as specified.

Supply and fixing 32 mm Waste Coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including taking down existing one complete all as manufactures and all as specified and directed by Engineer- In - charge

Supply and fixing Rotational moulded polythene water storage tank of 500 Ltrs capacity (three layer white colour) cylindrical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down of old unserviceable tank complete all as specified and directed.

Material and labour for Granite 18 to 20mm thick (table rubbed and polished) in steps,Jamps, Pillars, Windows, cills, platforms, walls and like CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade of Granite over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) all as specified and as directed. Note : (a) The Unit rate quoted is included for Demolition of Stone Slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar (b) The manufacturer's test certificate and individual test certificate of Tiles must be submitted for approval by the concerned authority prior to installation.

Supply and fixing PVC connections 15mm size with PTMT nuts of length 600 mm including taking down existing one complete all as manufactures and all as specified and directed by Engineer- In - charge.

Supply and fixing Vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) and including seat cover for pedestal pattern complete fixed in repair, all as specified and as directed.

Supply and fixing in repair Ball valves 25mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe & fixed. (minimum weight -210 gms) complete all as specified and directed.

Supply and fixing in repairs 40mm bore unplasticised PVC pipe of pressure rating 10 kgf/Sqcm fixed complete to walls, ceiling or laid in floors complete all as specified and directed.

Supply and fixing in repair PVC waste pipe 32 to 40 mm dia and length n exc 2m for WHB/Sink/Urinal up to floor trap and fixed complete all as specified

Taking down steel tubing 20mm bore and connections including cleaning and refixing of old GI tubing 20mm bore including connections in new or old position (wall, ceiling & floor)complete all as specified and as directed. Note :- The unit rate quoted is deemed to include for all fittings required for re-connection.

Supply and fixing PVC (SWR) pipes single socket in any length with rubber ring joints of 75 mm bore fixed to wall including taking down existing one complete all as specified and as directed by Engineer-in-Charge

Supply and fixing PVC bends 75mm bore including taking down existing one complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in repairs PVC (SWR) floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement complete all as specified and as directed.

Supply and fixing PVC (SWR) pipes single socketed in any length with rubber ring joints of 110 mm bore fixed to wall/floor including taking down existing one complete all as specified and as directed by Engineer-in-Charge

Supply and fixing PVC bends 110mm bore including taking down existing one complete all as specified and as directed by Engineer-in-Charge

Supply and fixing PVC (SWR) 110mm junction vent cowl all as specified including taking down existing one complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in repairs Stack clamps made out of 50 mm x 5 mm flat iron and 110 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm bore complete all as specified and directed.

Supply and fixing in repairs Stack clamps made out of 50 mm x 5 mm flat iron and 75 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore complete all as specified and directed.

Supply and fixing in repairs 7 feet 4 pipes pulley operated cloths drying system consisting of aluminium pipe of outer dia 22mm, inner dia 19.80mm, made up of detrin with rope guide mounted on channel pair of length 24 feet (distance between two pipes is adjustable) locking system to hide rope knot, channel to be mounted or fixed with self taping screws provided in kit. Rope will be HDPE double core of 4mm dia fixing to ceiling as specified and directed by Engr-in-Charge and minimum weight of one pipe shall not be less than 0.20kg/, minimum weight of rope shall not be less than 7700Gms/unit .

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out steel/plastic/cpvc water tubing and connections including cleaning for refixing 15 mm/20mm dia .

Supplying and fixing in repairs of 20mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA CPVC complete all as specified.

Supplying and fixing in repairs 20mm outer dia CPVC brass elbow and all as specified.

Supply and fixing 15mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking down up or down 15mm bore steel tubing galvanized and connection including taking down or removal from site complete all as specified.

Supply and fixing 20 mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking down up or down 20mm bore steel tubing galvanized and connection including taking down or removal from site complete all as specified.

Material and labour for Petty repairs to leaking water in bib taps, pillar cock, stop cock, angle valve, concealed stop valve, bottle trap of any description by changing the PVC washers/ Sheet washers, spindle brass, jumper brass or any other minor accessories items included etc (incl taking down and refixing) complete all as specified and directed

Taking down & re fixing high or low level flushing cistern 10 ltrs capacity & connections to pipes & fixing of chain & pull or lever after cleaning inside of all dirt, scale formation, replacement of rubber washers, syphon set, float valve, stopping of leakage etc complete all as specified and as directed

Material and labour for Petty repair to renewing/matching glazed or ceramic coloured tiles in floors/walls in patches area not exceeding n exc 2.00 Sqm including dismantling, removing and cleaning old tiles preparing beds and laying screed bed in CM 1:4 setting, jointing and pointing new or old tiles and joints filling and apply white cement and complete all as specified and directed

Material and labour for Petty repair to wall mixer, basin mixer, sink mixer etc. including replacement of spindle brass, Jumper brass, rubber washer, head included taking down and refixing etc all as directed

Material and labour for Petty repair to internal/external water inlet water GI/CPVC pipe line of any size coming from over head tank to the quarter including socket,elbow,nipple ,with repair to water blockage , pipe line leakage, cleaning internally , removingof air/dust blockage including concealed water tubing etc n exc 3m length of any height using scaffolding and and making the water supply good complete all as specified and directed.

Material and labour for for 100 mm thick PCC 1:2:4 type B-2 (using 20 mm graded crushed stone agg) as in PCC in Hard standing etc. with , spike rolling ,or making impression of expanded metal, while the concrete is green complete all as specified and Demolition of Concrete (un reinforced) of any description and in any position not otherwise specifically provided.

Material and labour for Grinding of existing mozaic/kota stone/tiles in wall/flooring including mirror polishing, cleaning of tiles/granite and joints filling and apply white cement, including grouting of floor trap surroundings with white cement complete all as specified and directed.

LAKSHMI CONSTRUCTIONS

SRI MAHALAKSHMI CONSTRUCTIONS

M/S AMRITHESH ENTERPRISES

SRI LAKSHMI VENKATESHWARA ENTERPRISES

SRI GANESH ENTERPRISES