RequiredExperience with Government
RequiredAnnual Turnover
RequiredCertificate (Requested in ATC)
RequiredOEM Authorization Certificate
RequiredOEM Annual Turnover Bid to RA enabled Yes Fire Fighting And Hydraulic Rescue Platform ( 1 pieces ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) Generic Fire Fighting and Hydraulic Rescue Platform The Hydraulic Platform shall be designed specifically for fire fighting and rescue work. The entire unit shall be mounted on a The Hydraulic Platform shall be designed specifically for fire fighting and rescue work. The entire unit shall be mounted on a 1/14 Turntable on a CMVR certified BS-IV compliant Chassis. The Truck Chassis complete with Company Built Cabin and PTO Unit are included under this equipment Turntable on a CMVR certified BS-IV compliant Chassis. The Truck Chassis complete with Company Built Cabin and PTO Unit are included under this equipment Maximum Working Height from Ground level 42 42.0 Type of Fuel Diesel * Power Take Off (PTO Unit) Type - * Main Boom Configuration - * Number of Booms 2 * Number of Telescopic Sections 4 * Cage Capacity with Dry Monitor 500 500.0 Cage Capacity with Monitor delivering 3000 LPM 300 * Water Monitor capacity in (LPM) 3000 3000 Maximum Cage floor height from Ground level 40 * Maximum reach from Slew centre to Cage corner at full rated load 18 * Slewing (degrees plus endless
Requiredcontinuous in both directions) 360 360.0 Standard Sparewheel
RequiredTool Kit
RequiredFirst Aid Kit YES * List of Standard Accessories provided YES * Optional Accessory - Portable Pump 1500 LPM @ approx 9 Bar No * Availability of Drawing and Service Manual YES * Transportation Charge in Rupees Per Km 100 * Outreach Both Electro Hydraulic Both Electro Hydraulic 2/14 management as per manufacturer’s design shall be controlled automatically by and Computer Aided System and Computer Aided System Computer Override Mechanism for operations even in case of failure or malfunction of the Computer Aided safety system Yes
Requiredthe mechanism enables to override the electronic computerised controlled safety system and operate the machine with modified reach parameters
Requiredwith alternative mechanical hydraulic/electric safety at full load and stability Yes
Requiredthe mechanism enables to override the electronic computerised controlled safety system and operate the machine with modified reach parameters
Requiredwith alternative mechanical hydraulic/electric safety at full load and stability Constructional and Performance Make & Model No of Chassis - * Emission Norms BSIV * Chassis with Built up Cabin for Driver YES * Engine Power Max 210 Above 170 Engine Torque Max - * Wheelbase 6150 * Drive 2-WD 2-WD
Required4-WD Fuel Tank Capacity 300 * Overall Stowed Length 12 12.0 Overall Stowed Width 2.5 * Overall Stowed Height 4 * Overall Width (with all outriggers fully extended) 7.5 7.5 Overall Width (with one side jacking) 5.5 5.5 Static Stability of fully built up Unit on Chassis to incline of 15 * Turning Circle Radius 11.4 11.4 Gradeability (%) 20 * Maximum Speed (km/hr) 80 * Front overhang of the Built Up Unit 1 * 3/14 Rear overhang of the Built Up Unit (in % of wheelbase) 60 * Overall Weight of Built Up Unit shall not exceed Chassis GVW YES YES Maximum penetration of outrigger base plate below firm horizontal ground suitable to level vehicle on incline of 7 * Spirit level indicator provided Yes * Cage Dimensions Outer +/- 5% approx 1045x2050x1150 (LxWxH) (in mm) - * Independent Cage Slewing (left and right) 45 * Mounting of Cage for Up and Down movement Direct Attachment * The cage must be horizontal in all operating positions through an electronically (or hydraulic) controlled levelling mechanism Yes * Additional switch/lever control shall be provided in the cage to allow operator to adjust the cage level Yes * Water Monitor Type Water cum Foam * Water spray curtain system for protection from radiant heat Yes * Boom shall be Box-type section made of corrosion resistant high strength steel grade FE540 to IS 2062 reaffirmed 2000/ST55 to IS 961 or Superior Yes * Welding Process for fabrication work MIG WELDING migwelding In operating position
Requiredthe Unit Yes
Requiredoutriggers having sufficient power and Yes
Requiredoutriggers having sufficient power and 4/14 shall be stabilized on 4 nos H-type (hydraulic out and down type) outriggers stroke to lift all wheels of the vehicle off firm level ground stroke to lift all wheels of the vehicle off firm level ground Operating Position - Option 1 All 4 outriggers are extended fully horizontally: Slew through full circle permitted
Requiredunlimited
Requiredendless
Requiredcontinuous All 4 outriggers are extended fully horizontally: Slew through full circle permitted
Requiredunlimited
Requiredendless
Requiredcontinuous Operating Position - Option 2 Outriggers on left side extended horizontally fully but not fully on right side of vehicle: Slew permitted on left side only Outriggers on left side extended horizontally fully but not fully on right side of vehicle: Slew permitted on left side only Operating Position - Option 3 Outriggers on right side extended horizontally fully but not fully on left side of vehicle: Slew permitted on right side only Outriggers on right side extended horizontally fully but not fully on left side of vehicle: Slew permitted on right side only Outreach management as per Manufacturers design shall be controlled automatically by a combination of electrical
Requiredmechanical and/or hydraulic safety systems YES * There shall be an on- board computer system
Requiredwhich receives geometric information through redundant (dual information) sensors Yes
Requiredthe computer software is designed to automatically restrict the outreach and load to within safe limits to ensure stability of the machine * Digital cage load display
Requiredwith alarm and cut-off indicating overload
Requiredirrespective of reach
Requiredheight or position of the hydraulic platform with 20% overload allowance (ie load in cage not to exceed 600kgs) YES * Electro-hydraulic proportional joysticks for controlled and simultaneous YES * 5/14 movements of booms and slew shall be provided Automatic stops to prevent platforms from reaching unsafe area of operation shall be provided YES * The equipment shall be powered by a double hydraulic pump powered by the vehicle engine through PTO unit YES * When one of the booms or slew movement is operated
Requiredthe control valve shall automatically increase the pressure and oil flow to the extent needed for the movement activated Yes
Requiredand when hydraulic platform is not in operation
Requiredthe pump shall operate on minimum flow and minimum pressure * The main platform control levers shall allow for a progressive control at infinite variable speed from creep to maximum and proportional to the joystick lever position YES * The system shall be equipped with an inbuilt provision to provide smooth start or stop controls for relatively jerkfree operation
Requiredproviding automatically for a progressive acceleration or deceleration of the main platform movements YES * All controls shall be of 'Deadman' type and return automatically to neutral position
Requiredstopping the motion if the control is abandoned YES * Deadman Switch type Through Foot Pedal * 3 sets of displays (at 1) Outrigger position 2) * 6/14 outrigger
Requiredturntable and cage control stations) on backlit colour monitors of at least 14cm size
Requiredwhich shall dynamically display information about Reach 3) Slew angle 4) Cage rotation angle 5) Cage load 6) Main boom angle 7) Height 8) Wind speed 9) Articulated boom angle Minimum inner diameter of the telescopic waterway made of stainless steel aluminium 75 * There shall be a 63mm inlet with closing valves on the rear of the vehicle
Requiredfrom where the line leads through the centre post
Requiredturntable and upto the water monitor in cage YES * The piping shall be simultaneously protected from possible over pressure by means of relief valve mounted underneath the turntable YES * Moving sections of the water pipe shall be thoroughly ground and chromium plated anodized YES * An additional outlet with 63mm closing valve and coupling for water supply from the cage shall be provided for extension hoses YES * There shall be a drain cock fitted in the pipe to enable it to drain the water after use YES * An inter- communication system shall be fitted between the turn-table and the cage YES * There shall be an electric siren unit with hooter fitted on the roof of the vehicle cab Yes
RequiredControl panel of the system is located in the driver’s cab with switches for the fast (Yelp) and slow (wail) * 7/14 sounds Command microphone with push to talk switch shall allow the public address message to override the siren function YES * Compressed breathing air supply from turntable to the cage shall be provided through a four way manifold at the cage along with four breathing air masks at cage Yes
Required4 nos. 6 litres 300 bar air cylinders is provided at the turntable * It must be possible to change the cylinders without interrupting the air supply; pressure regulator shall also be incorporated in the system YES * Electric supply shall be taken from the chassis battery
Requiredwhich shall be charged when the engine is running 24 * The Telescopic Rescue Ladder System Shall be provided attached on to main boom structure at several points throughout its length and front end in the telescopic sections that shall allow direct continuous rescue way with cross or no cross over platform or similar obstacle * Telescopic Rescue Ladder System - Distance between each rung 280 * Each rung of the ladder shall be able to support load without any permanent distortion 300 * Spot Light at Cage railing and at Rear of body shall be provided 4 * Rotating Beacons: Two rotating blue beacon YES * 8/14 lights
Requiredone on each side of the driver cab roof shall be provided Painting : All surfaces of steel structure and hollow structures shall be chemically mechanically cleaned for rust removal
Requiredafter which they shall be primed All booms shall be painted from inside also Yes
Requiredpaint shades shall be provided as specified by the customer * Storage lockers shall be sufficient for all equipments which are required to be carried on the appliance including as below: YES * Flexible rubber suction hoses of 100 mm dia each and 3 m length 4 nos. * Canvas delivery hoses of 63mm dia and each of 15 m unfolded length 2 nos. * Metal outrigger ground plates with brackets 4 Nos * Portable oil pressure gauge attached to 1 m long hydraulic hose 1 no. * Drop down Stretcher carrier of 180 Kgs capacity for injured persons to be rescued 1 no. * Working range diagram
Requiredone at the turn-table
Requiredand one in the working cage
Requiredhard copy 2 nos. * Plug for 12/24 volts working light at the turn-table and in the cage 1 no. each * Lifting hook under the working cage 500 kg capacity YES * Anchorage points for safety harnesses for 4 persons in the cage YES * Safety and Inspection The Hydraulic YES YES 9/14 Parameters Platform shall comply with the Safety requirements and features as per EN1777 norms and other national international norms & standard Test Load for Stability at full outreach 750 750.0 Max Safe Operating Wind Speed at Max Height/Reach and Rated Cage Load ( in m/sec) 12.5 * Electronic Auto- Leveling of Vehicle Yes
Requiredthrough single push button to level Vehicle upto an accuracy of 0.5 degrees
Requiredoperation not allowed if vehicle is not in level position * Automatic Slew Restriction
Requireddepending on outrigger position Yes
Requiredit shall automatically prohibit the slew movement on the side where the outriggers have not been fully extended * Interlock to prevent boom operation
Requiredunless outriggers are deployed and vehicle levelled YES * Interlock to prevent outrigger movement unless the Platform is fully stowed YES * Cage collision guard with automatic cut-off and possibility to over- ride the cut-off as decided by operator in cage YES * Display of cage load and alarm if load is exceed and automatic cut-off YES * Indication in driver’s cabin for PTO
Requiredlocker open
Requiredoutrigger stowed position so that driver knows that it is safe to Yes
Requiredvisible only when PTO lever is engaged * 10/14 drive after completion of all operations Automatic cut-off and alarm in case any outrigger loses contact with ground YES * Static Stability of the equipment
Requiredduly mounted on the chassis
Requiredin transport position
Requiredshall be stable upto 15 degree incline or higher YES * Test to verify if the outriggers are designed to level the vehicle on slope of 7 degree in both longitudinal and transverse directions Yes
Requiredthe level shall be measured with a digital inclinometer and the error in leveling shall not exceed 0.5 degree Yes
Requiredthe level shall be measured with a digital inclinometer and the error in leveling shall not exceed 0.5 degree Pressure overload protection for hydraulic pumps through pressure relief valve in main control valve shall be provided YES * All cylinders shall be provided with load holding valves to prevent boom crash in case of hose failure YES * Restrictor valves for slow descent in the event of lock valve failure YES * Emergency cut off device at turntable and at the cage to cut off all functions
Requiredwith easy restoration YES * Emergency backup system with auxilliary hydraulic pump for stowing the equipment in case of Main pump
RequiredPTO or vehicle engine failure Both Engine and Battery driven Both Engine and Battery driven Certifications
RequiredSelf Declaration and Test Reports ARAI/VRDE/ICAT No of the Chassis for compliance to CMVR '1989 and any - * 11/14 amendments Form 22 A - For compliance with pollution standards
Requiredsafety standards of components and road worthiness as per CMVR Rules - * Fire fighting and hydraulic rescue platform certification from ARAI/VRDE/ICAT as a complete product including chasises (Indian/Imported) YES * ARAI/VRDE/ICAT certification number - * ARAI/VRDE/ICAT certification date - * Spares and Service support shall be available locally for minimum 7 years by its OEM or authorised Dealer YES * Certification of complete system for Safety requirements and features as per EN1777 norms and other national international norms & standards - * Inspection Report Test Certificate from any Govt organization in India verifying the safety systems as listed in the Safety and Inspection Parameter section shall be provided YES YES Test Reports from Central Govt/NABL ILAC acredited lab for Mechnical Test (as per ASTM A 370:2014 or IS 1608:2005) and Chemical Analysis (as per ASTM E 415:2014) YES YES 12/14 confirming to ST55 to IS916 or similar Indian Standard Test Reports from Central Govt/NABL ILAC acredited lab for Welding Quality YES YES Manufacturer shall provide Test Certificates for safety systems which require dismantling reassembly YES * Manufacturer's Test Certificates for various bought out items components shall be provided YES * Warranty Time (in years) 3 3
Required5 Number of Free Service 6 * Training and Commissioning at site YES * * Bold specifications are the golden parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer.
