Addn Altn to Bldg P 94 SMC and Provn of Toilets and Rest Room at Dharna Club at AF Stn Deolali

Amount

Excavation in post holes (or similar holes) each not exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm watering and removing surplus soil to a distance n.exc 50m and making good disturbed surface complete all as specified and as directed.

M&L PCC 1:3:6 typeC-2 (using 40 mm graded stone aggregate) as in foundation for concrete post/struts.

S & F Steel work in tubular trusses and posts, purlins and rafters (square / rectangular / circular sections), including special shaped washer, cleats and plates to the joints for welding etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.5 mm thick of an colour having tensile strength of 550 Mpa as in ridge/valley gutter etc fixed with self tapping screws as specified.

M&L preperation of new steel surfaces of any desciption over 10 cm in width or girth not other wise descibed and applying two coats of synthetic enamell paint over one coat of red oxide .

Surface dressing not exc. 15 cm deep and getting out in any type of soil, complete all as specified

M&L for 75 mm thk PCC 1:4:8 type D-2 as in sub base to flooring.

M & L hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

Excavation in trenches n. exc 1.50 m wide and n.exc 1.50m in depth for foundation shafts, wells, manholes etc n.exc 10 Sqm on plan and n.exc 1.50M in depth and getting out in hard / dense soil , complete all as specified and directed.

Returning filling in including spreading, levelling,watering and well ramming in layers not exceeding 25cm thick.

Removal of surplus soil to a distance exceeding 250m and n exc 500 m and depositing where directed at a level not exceeding and depositing where directed at a level not exceeding 1.5m above the starting point and disposal.

M&L PCC 1:4:8 type D-2 (using 40mm graded aggr) as in fdn filling and mass concrete all as specified.

M & L Reinforcement cement concrete M-25 ( Design mix) as in foundations including rafts, footings, foundations beams, plinth beams, bases for columns and basement slabs etc complete all as specified and directed.

M & L Reinforcement cement concrete M-25 ( Design mix) as in columns, pillars, piers, posts and struts etc complete all as specified and directed.

M & L Reinforcement cement concrete M-25 ( Design mix) as in beams, cantilever, bressummeres lintels over 1.50m spam complete all as specified and directed.

M & L Reinforcement cement concrete M-25 ( Design mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

& L for form work to soffits of suspended slabs landing and similar work n.exc 200 mm thick horizontal or sloping rough finished flat surfaces on concrete all as directed by Engr-in-Charge.

M & L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, including flat rough finished surafaces of concrete complete all as specified and directed.

M & L Formwork to sides of pillars, posts, struts, piers, columns, and stanchions, square, rectangular or polygonal in shape, including flat rough finished surafaces of concrete complete all as specified and directed.

M & L Form work to sides and soffits of floor and roof beams, beams haunching, girders, bressummers, lintels and cantilever, shelves including supports over hangs etc rough finished surfaces of concrete ( flat ) complete all as specified and directed.

Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified & directed.

Mild steel TMT bars 6 to 10mm dia ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, (as in stirrups) hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to Fe-310-O or Fe-410-O all as specified & directed.

M & L Brick work with fly ash bricks (Old Size bricks) straight or curved on plan exc 6 mtr mean radius built in CM (1:6) all as spd and directed

M&L Rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed

M&L Rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4) finished even and fair without using extra cement complete all as specified and directed

M&L for rendering/screed bed 10mm thick in cement mortar 1:4 on concrete surfaces mixed with water proofing compound @ 3% by wt of cement finishing the surfaces even and smooth without using extra cement all as per directed by Engr-in-Charge (Note:- Supply only water proofing compound shall be measured & paid separately)etc complete all as directed by Engr-in-Charge

M&L for cleaning the newly plastered surfaces thoroughly with wire brushes and providing water proofing treatment all as given her in after:- (a) Bituminious primer @ 0.3 ltr per Sqm confirming to IS 3384-1986 on roof surfaces prior laying APP membrane. (b) providing water proofing treatment 3mm thick weighing not less than 3.5 kg/sqm APP (Atactic polypropylene)modified bituminous membrane reinforced with non voven polyester mat of (wt not less than 160 gms/sqm) laid on primed surfaces with 100mm overlap,applied by thermo fusion using LPG torch on the bottom portion of the membrance (c) Applying one coat of bituminous aluminium paint @ 100 gms per sqm over membrane complete all as directed by Engr-in-Charge(Make - HYDROSTOP of M/s Tiki Asphalt Ltd., HYPER PLAS POLYSTER OF IWL INDIA Ltd, Chennai, SUPER THERMOLAY of M/s STP Ltd, Mumbai)

Supplying only liquid water proofing compound

M & L Damp proof course 40mm thick in cement concrete 1 : 2 : 4 type BO to horizontal or vertical surfaces including necessary formwork

M&L 25 mm thick PCC ,type B-1 (20 mm graded aggregate) in flooring cmplete all as specified and directed.

M & L for coloured (light shade) vitrified ceramic tiles 10mm thick (Square/rectangular) polished, area of each tiles n. exc 0.36 Sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match and the shade of the tiles including 15mm screed bed or bedding layer CM 1 : 6 all as specified and directed by Engineer-in-Charge.

M & L for coloured (light shade) vitrified ceramic tiles 10mm thick (Square/rectangular) polished, area of each tiles n. exc 0.36 Sqm in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles including 10 mm thick rendering CM 1 : 4 all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tiles exc 0.11 Sqm but n.exc 0.18 set and jointed in neat cement slurry and pointed in white cement with pigment to match over and including 15mm thick in CM 1:6 screed bed complete all as specified & directed by Engr-in-Charge.

M & L Preparation of new plastered surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper complete all as specified & directed.

Complete removal of existing treatment etc on walls and applying two coats of cement base paint over a coat of primer on wall surfaces of any description all as specified & directed by Engr-in-Charge

M & L Preparation of new plastered surface of wall by applying two coats of cement base paint over a coat of primer on wall surfaces of any description all as specified & directed by Engr-in-Charge

Complete removal of existing treatment of walls by steel wire brushing, prepariation of surfaces and applying two coats of distemper oil emulsion after chalk whiting or JK wall care putty 2 mm thick over the walls all as specified and directed by Engineer-in-Charge.

Dismantling of stone slab and tiles of any description or thickness in floors aprons etc laid, bedded & pointed in any mortor complete all as specified & directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified & as directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors (below or above ground level ) n exceeding 15 cm thickness and including removing demolised PCC form site exc 500 mtr but nexc 1500 Mtr depositing where directed

M&L 20 mm thick Granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite over 15 mm thick cement screed in CM 1:4 including Roughening surfaces of old concrete floor by picking,sweeping clean and washing down with water to remove dust etc and brusing neat cement slurry with 3.00 kg per sqm all as spd & directed.

M&L for Glazed ceramic tiles in vertical surface 450x 300x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 15mm thick bedding layer/ backing coat in CM 1:4 complete all as specified and directed.

Taking up or down GI tubing 15mm bore and connections from walls and ceiling or laid in floor including cleaning for refixing or removal to store all as directed by Engr-in-Charge

S&F GI tubing 15mm bore medium grade with all fittings and fixed complete to wall, ceiling or laid in floor with suitable clamps & nuts etc all as directed by Engr-in-Charge

M&L cutting chases with diamond cutter pinning in brick mas and making good to facing where required and pointing in cement and making good in CM 1:3 cutting n.exc. 10 cm in girth.

Taking up or down GI tubing 20mm bore and connections from walls and ceiling or laid in floor including cleaning for refixing or removal to store all as directed by Engr-in-Charge

S&F GI tubing 20mm bore medium grade with all fittings and fixed complete to wall, ceiling or laid in floor with suitable clamps & nuts etc all as directed by Engr-in-Charge

S&F bib taps 15mm bore cast copper alloy chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as directed by Engr-in-Charge

S&F stop cocks 15mm bore, chromium plated, fancy type screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions with long shank and cup washers all as directed by Engr-in-Charge

S&F in repairs low density polythelene pipes 40mm bore fixed complete to walls, ceiling or in floor all as directed by Engr-in-Charge

S & F wash hand basins, vitreous china( flat back) white of size 550mm X 400mm including cutting for and pinning in ends of brackets or erecting stand including waste fitting, brass chromium plated 32 mm size with long screwed shanks and fly nuts and including PVC discharge pipe complete all as specified and directed by Engr-in-Charge.

S & F 15 mm bore dia. of pipe fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F in repairs vitreous china water closet (squatting pan) Orrisa pattern of size 580 x 440mm white with intergral footrests & 'P' trap (excluding flushing cistern and flush pipe) including connection to trap, to flushing pipe etc. complete including PCC for making good to floor etc. complete all as directed by Engr-in-Charge.

S & F vitreous china wash down water closet (Pedestal pattern) white (EWC) including white PVC seat cover closed pattern with flat bottom and cover and mild steel chromium plated hinge device,connection to drain or outgoing pipe and to flushing pipe, antisyphonage pipe joint to socket or stoper etc, complete all as specified and directed by Engr-in-Charge.

S & F in repairs low level flushing cistern of syphonic action type 10 ltr capacity PVC fixed to wall with bracket and screwed including PVC flush pipe complete fitting etc all as directed by Engr-in-Charge.

S&F PVC connection 15mm bore dia.of pipe with PTMT nuts and PVC washers of length 600 mm all as directed by Engr-in-Charge.

S&F in repairs float valve 20 mm bore of high pressure, PTMT with epoxy coated aluminium rod and high density plastic ball screwed, for iron pipe and fixed complete all as directed by Engr-in-Charge.

S&F in repairs Grating doom 100 mm dia with waste hole of PTMT (Minimum weight 50 gms) all as directed by Engr-in-Charge.

Dismantling unserviceable water tank of capacity n.exc 500 ltr complete all as specified and as directed

S&F Rotational moulded polyethylene water storage tank of 500 ltr capacity (cylinderical vertical with closed top ) hoised and fixed in position all as specified in SSR part I and as directed.

S&F in repairs tubular towel rail brass chromium plated,20mm dia, D type,60cm long between flanges ISI marked complete all as specified.

S&F in repairs drapery curtain rod of metalic 25mm dia covered with PVC coating complete with MS bracket golden colour rings and side caps fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw compete all as specified as directed by Engineer -in -charge

S&F door closer hydraulically regulated designation No-2 universal type ISI marked suitable for door shutter of weight between 36 to 60 kg, cast iron body complete and all as specified. Make : Everest/Zip/Natraj as approved by GE.

M & L for false ceiling work of aluminium snap grid system size 605x605mm for false ceiling with aluminium angles of size 23.5 mmx23.5,,x1.5mm fixed to wall with GI screws and aluminium tee of size 37.5x37.5x1.5mm in main and cross runners fixed 60 cm c/c and tied to existing roof/truss/rafters complete

M & L for hanging of aluminium false ceiling grid with 3 mm dia GI wire(upto necessary required length & 1.2 Mtr c/c) fixed to slopping roof (rafter/purlin/trusses) complete all as specified.

M & L Non asbestos fibre cement building boards 6 mm thick, fixed or laid/ inserted to Aluminium grid frame work in ceiling with clips all as specified and directed.

Taking down chowkhats of frames exc 1.50 sqm but n. exc 4.0 sqm with shutters (without taking off shutters from the frames) all as spd.

S & F powder coated sections for doors, windows, partiotins including frames of size as approved and fixed all as specified and directed (Note : (i) Paneling such as glass , Gauge etc will be measured and paid saperately.(ii) The rate quoted under this item deemed included for necessary jointing cleates, glazing clips, alluminium beading, screws, rubber packing and locking devices & in built handles for sliding windows. However, no element on account of weight will be taken into consideration for these item.(iii) Floor door spring/locks/tower bolts/ handles/ door closure/hinges for doors measured saparately.(iv) Size of door / windows shall be all as directed at site.(v) Grills will be measured saparately.(vi) Second class hard wood batten of appropriate size to be inserted inside the frame for fixing hinges and the same is included in the rate quoted.)

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, orstainless steel wire staples all as specified & directed.

S & F plain sheet glass 5 mm thick tinted, fixed to aluminium doors/ windows / ventilators complete all as directed by Engr-in-Charge (Note:- Beading/rubber packing is included in the rates for aluminium sections above.)

S & F 12 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

M&L for Chequered cement concrete tiles 25cm x 25cm x 25mm thick, set, jointed and pointed in near cement slurry in floors with grey cement and pigment over 15 mm thick screed bed in CM 1:6

S&F Framed work such as grills, gratings door chowkats etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

M&L preperation of new steel surfaces of any desciption over 10 cm in width or girth not other wise descibed and applying two coats of synthetic enamell paint over one coat of red oxide .

S & F 105x60mm pressed steel frame for door with one or more rebates incl necessary fixing lugs, hinges, lock strike plate, etc complete incl plain cement concrete Type BO 1:2:4 (using 12.5 mm graded stone aggregate) cast in situ in filling to steel frames including use of form work.

M & L for cement concrete 1 : 4 : 8 type D-2 using 40mm graded stone aggregate, as in bed to drain pipes for bore of pipe 150mm dia. including packing under, and haunching against the sides of pipes after they are laid and tested all as specified and directed.

M & L for Reinforced concrete pipes, class NP2, laid and jointed complete with collars for internal diameter pipe 150mm dia. laid in trenches and jointed all as directed .

M & L for providing precast cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate in landings, cover slabs (for manholes etc) and similar small articles with plain fair surfaces, and set in cement mortar 1:4.Completed all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required (internal dia of pipe 150mm) Complete all as specified and directed.

Surface dressing n exc 15cm deep and getting out soft/loose soil, complete all as specified

Brick work with sub class'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:6) all as spd and directed

S&F Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

S&F Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

Cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair incl making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified

M&L for 100 mm thk PCC 1:4:8 type D-2 as in subbase to flooring.

M&L 25 mm thick PCC ,type B-1(20 mm graded aggregate) in flooring cmplete all as specified and directed.

M & L screed bed or bedding layers of mortars 15 mm thick in CM 1:4 for laying floor finishes.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement. all as spd and directed

M&L Rendering 10mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

M&L two coats of distemper oil emulsion over a coat of primer including preparation of new surfaces complete all as specified and directed

S & F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat to fixing etc, complete all as specified.

S & F anodised aluminium window and ventilator shutters, fixed tyupe without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws etc complete all as specified.

S & F anodised aluminium sliding window two/three (Bombay sliding window) made out of hollow extruded aluminium section as mentioned below and glazed with tinted glass 4 mm thick fixed with glazing clips, rubber beding/gasket anodized aluminium beading screws and star lock type handles of size 75 mm 2 Nos alumium tower bolt 150mm long etc complete all as specified and directed by Engr-in-Charge with the follwing sizes :- a) Shutter & bottom size 37.5x15x1.60mm thick 40x18x1.09 mm thick b) Shutter inner lock size 37.50x15x1.60 mm thick 40x18xx1.00 mm thick c) Shutter side (handle) size 37.50x15x1.36mm, 40x18x1.09 mm thick d) Chokat bottom size 50.30x26x1.00mm, 92x31.75x1.10 mm thick e) Chokhat top & sides size 50.30x15x1.00mm 92.31.75x1.05mm thick Make (i) Anodized aluminium section : Jindal/Hindlaco, Indalco (ii) Glass : Sanit Gobin, Modi Guard, TATA Note : One window in each bedroom should be having made with provn of AC opening with top hung shutter fixing with hing and fixing of aluminium grill all as directed by Engr-in-Charge.

Pressed steel frames for doors made out of MS sheet 1.25 mm thick of size 105x60 mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. including filling of concrete 1:3:6 typeC-0 12.5 mm aggregate , complete, as specified,supplied and fixed ®

35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated fitted to chowkats all as specified and directed

M & L preparation of new wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing

S&F solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frames shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing.

Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks, or galvanized wire staples all as specified & directed.

S&F 100 mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type C-21.

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts all as specified.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed.

S&F 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked all as specified.

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all as specified.

S&F 20 mm size gun metal globe or gate valves with iron wheel head, screwed both endsfor iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe .

S&F Bib taps fancy type for 15 mm bore pipe, cast copper alloy fancy type chromium plated of Make - Jaquar , Marc and Johnson complete all as spd and directed.

S & F Vitreous china wash basin(Oval Shape), white flat back,size 550 x 400 mm including waste pipe , brackets and cutting for and pinning in ends of brackets or errecting stand and 32 mm dia PVC waste pipe including waste copling 32mm size full thread , all as spd and directed

Vitreous China urinals, bowl S&F vitreous china urinals half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

PVC connections 15mm size with PTMT nuts of length 450 mm

Rotational moulded polyethlene water storage tanks of capacity 250 litres three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete including 20mm dia ball brass valve high pressure with polythene float complete all as specified & directed.

S&F 100 mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears laid in floor with cement joints all as specified.

S&F 100mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured) with ovel asses door complete all as specified and directed

S&F 75mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears fixed to walls with clamps and cement joints all as specified.

S&F 75mm CI bends diminishing pieces or tapers

S&F 75 mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured)

S&F CI floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 for waste pipe complete all as specified.

S&F cast iron cowl for 75 mm dia all as directed by Engr-in-charge.

M&L in repair 150x100 mm Salt glazed stoneware gully traps, square or round mouthed, type‘P’

S&F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof for 75 mm dia of pipe

M&L for point wiring complete with two single core, PVC insulated, unsheathed, multi stranded bright annealed copper conductor cable, 1.5 Sq.mm 1100 Volts, FRLS grade drawn through and including heavy duty PVC casing and capping not less than 20 mm width and accessories surface mounted on walls, ceilings etc. on & including PVC board with earth dolly arrangement with surface plate for mounting switches, sockets, regulators etc and one run of 1.5 Sq.mm PVC insulated, unsheathed, multistranded, copper conductor cable FRLS grade as earth wire and connected to common earth dully complete for One light/fan point controlled by one switch.

All as per item no- 123 above but One 3 pin socket out let 5 Amps on independent board.

All as per item no- 123 above but One 3 pin socket out let 5 Amps on Same board.

All as per item no- 123 above butOne bell point controlled by one push button.

All as per Sl item No-123 above but with two runs of 2.5 Sq.mm cable and one run of 1.5 Sq.mm cable as earth wire for one 3 pin socket outlet/power point 15 Amps controlled by one switch.

Supply & fix switch piano flush type single pole one way 5 Amp.

Supply & fix switch piano flush type single pole one way 15 Amp

Supply & fix Socket out let 2 in 1, 5 pin 5 Amps flush type.

Supply & fix Socket out let 2in1,3 pin 5 and 15 Amps flush type.

S&F lamp holder PVC/ Poly carbonate type with back plate suitable for batten fitting SP 230 Volts

S&F ceiling rose,3 phase/ PVC /polycarbonate isolated body,65x50 mm two to three terminals

S&F Bell push 5 Amps SP one way suitable for 230 Volts flush type 2 module.

S&F electric bell Ding Dong AC 230 volts single pole.

S&F in repairs Fan regulator electronic solid state with various steps variable speed suitable for ceilling fan of size 900 to 1500mm sweep working on 230 V AC supply with all necessary connections

Supply & fix in repair decorative ultra slim square profile LED Light fitting of min 20 W rating aluminium housing along with integrated driver, environmental friendly, energy efficient ready to use pack 20W LED 6000K, complete all as specified and as directed by Engineer-in-Charge. Make: Havells cat part No Lumiline+BS20WLED840SPCSS or equivalent in Bajaj/CG.

Supply & fix in repair decorative ultra slim square profile LED Light fitting of min 10 W rating aluminium housing along with integrated driver, environmental friendly, energy efficient ready to use pack 10W LED 6000K, complete all as specified and as directed by Engineer-in-Charge. Make: Havells cat part No Lumiline+BS10WLED865SPCSS or equivalent in Bajaj/CG.

S& F and connecting up surface mounting decorative bulk head LED ,energy saving, environmental friendly, long life, corrosion resistant complete with LED and connecting up with and including size 3 core copper flexible wire from connector to ceiling rose/adoptor including all necessary fixing arrangements complete. Havells, (CAT No.RUGBYGENXFTS10WLED865SSYMBOPC) or equivalent in Philips/Bajaj/Cromton Greaves.

S & F Sheet Metal enclosure double door for mounting MCBs with 200 A rated bus bar 4 way AC 240 Volt with IP-43 protection including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge . Make Indoasian/L&T/HPL

S&F in repairs MCB SP 6-32 Amp.

S&F in repairs MCB SPN 40 Amp.

S&F in repairs wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulating copper stranded conductor single core cable in surface/ recesed as required earth wire in and including PVC Casing Caping of suitable standard size of :-Two run of copper conductor of size 6.0 sq. mm + One run of 6.0sq. mm as earth wire.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead of GI Strip 25 x 4 mm fixing on wall by means of bolts, nuts and washers of the earth wire.galvanised iron or steel and thimbles and other end of the earth strip connected to earthing test point and protected by galvanised iron pipe light grade 40mm dia and water pipe 20mm dia GI light grade with funnel and wire mesh, PCC chamber in cement concrete (1:3:6) type C-2 and CI cover with frame all as shown in electrical plate No. 5 of SSR part-I all as specified and directed

Supply & fix in repair ventilating fan made out of high quality engineering plastic, resistant to colour change with anti static properties, 250mm sweep suitable to work on 230 Volts 50 Hz AC supply of Havells: model no VENTILAIR DX or equivalent of CG/Bajaj including connecting to ceiling rose all as required or directed.

S&F new Storage water heater 25 ltrs capacity vertical mounting AC 230 Volts BEE 5 Star rating including connecting cord and plug, safety valve, nuts and bolts, PVC Flexible connections with length 450mm long 15mm dia with brass hexagonal adoptors both side duly ISI marked Suitable for hot/cold water complete including grouting of nuts and bolts, complete all as specified and directed Make Havells/Venus/V Gaurd

S&F MCB protected socket including 25 A MCB SP , plug top and MCB SP for AC/Gyser connection all per directed by Engineer in charge. Havells cat part No DBOXX MCB Protected socket 25 A or equvlt in Anchor/Standard..

Supply and install hi wall split units indoor/outdoor 5 star srated, invertor type complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality of capacity 1.5 TR

Supply & Fixing BLDC energy efficient ceiling fan AC single phase 230/240 V of size 1200 mm sweep including connect with PVC insulated and overall sheathed flexible copper conductor cable 3 core of size 0.50 sqmm and including hanging arrangements made out of MS clamps with nuts, bolts and washers all as specified and directed by Engr-in-Charge. Make : Anchor / Havells / Khaithan /Bajaj

Supply & fix in repair decorative ultra slim square profile LED Light fitting of min 20 W rating aluminium housing along with integrated driver, environmental friendly, energy efficient ready to use pack 20W LED 6000K, complete all as specified and as directed by Engineer-in-Charge. Make: Havells cat part No Lumiline+BS20WLED840SPCSS or equivalent in Bajaj/CG.

Supply & fix in repair decorative ultra slim square profile LED Light fitting of min 10 W rating aluminium housing along with integrated driver, environmental friendly, energy efficient ready to use pack 10W LED 6000K, complete all as specified and as directed by Engineer-in-Charge. Make: Havells cat part No Lumiline+BS10WLED865SPCSS or equivalent in Bajaj/CG.

S & F LED 10 W (candle /ball type) with B-22 base, complete all as specified and directed. Make -Havells/Philips/Halonix

S&F in repairs Sub main wiring with PVC insulated un armoured heavy duty copper conductor 1100 Volts FRLS grade 2 single core 4 Sq.mm cable and one run of 4 Sqmm copper earth wire for continuous earth fixed on wall/ceiling/floor etc. drawn in PVC casing capping / PVC non metallic conduit complete all as directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1,5 mtrs in depth for laying of cables including getting out in any kind of soil complete all as specified and directed. (cable shall be laid 60 cm below ground level )

Supply and lay 20 mm bore galvanised steel water tubing medium grade including all fittings such as bends, elbows, tees, reducers, sockets, union etc and laid in trenches complete all as specified and drected .Note : Excavation & earthwork will be measured & paid sperately

Vinod Enterprises

shubham Enterprises

A V S Builders

DEVA CONSTRUCTION

MAHIMA CONSTRUCTION