Chanakya National Law University, Patna invites E-Tender in two bid system for Improvement of Main Entrance Gate (Gate No. 01) with Security Guard Room, Improvement of Gate No. 03 and Improvement of Main Entrance to University Administrative Building of CNLU, Patna

Chanakya National Law University Nyaya Nagar, Mithapur, Patna-800001

Bill of quantity for landscaping work between Gate 2 to Gate 3, NW part of Libraray & near Playground

Si.no. Rate Source Item Unite Qty Rate Amount

Plinth Protection

4.17 Makingplinthprotection50mmthickof cement concrete1:3:6 (1 cement :3 coarse sand:6 graded stone aggregate 20mm nominal size)over75mm thick bed of dry brick ballast 40 mm nominal size, well rammedand consolidated and grouted with fine sand, including finishing the top smooth. Sqm 436.6

6.44 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). Metre 42.9

Part-I ( Bihar SOR 2022)

1 2.6.1 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.All Kind of Soil Cum 902.66 314.9 284247.63

0 20.2.1 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 300mm dia pipe Metre 60.00 902.6 54156

5 20.4.1 Extra over single under ream for providing additional bulbs in under reamed piles, under specified diameter(only the nos. of extra bulbs are to be paid)300 mm dia piles Each 12.00 1621.6 19459.2

CC and RCC Work

2 4.1 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

2.1 4.1.3 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) Cum 160.99 3998.1 643658.12

3 4.1.8 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size) Cum 2.84 2975.2 8449.57

4 16.64 Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer-incharge. Sqm 2135.80 237.4 507038.16

5 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l, Sqm 344.79 283.3 97679.01

6 2.28 Supplying and Filling in plinth with local sand and under floors including,watering, ramming consolidating and dressing complete. Cum 141.69 287.3 40707.54

7 5.1 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

7.1 5.1.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) Cum 27.76 4688.3 130147.21

7.2 5.2 Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

7.2.2 5.2.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) Cum 2.25 5670 12757.5

7.3 5.3 Reinforced cement conrete work in beams, suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size). Cum 16.51 5335.9 88069.03

8 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete

8.2 5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. Kg 1757.8132 94.5 166113.35

8.3 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. Kg 756.896 92.6 70088.57

8.4 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. Kg 1682.42 90.8 152763.59

8.5 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia. Kg 745.76 91.7 68386.19

9 5.9 Centring and shuttering including strutting,propping etc. and removal of form for.

9.1 5.9.1 Foundations, footings, bases of columns etc. for mass concrete Sqm 461.8735 211.6 97732.43

9.2 5.9.2 Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc. Sqm 16.52 375.1 6196.65

9.3 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts Sqm 181.6 494.4 89783.04

9.4 5.9.21 Lintels, beams, plinth beams, girders, bressumers andcantilevers with water proof ply 12 mm thick. Sqm 42.192 518.9 21893.43

9.5 5.9.20 Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick. Sqm 304 544.6 165558.4

10 4.11 Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size) Sqm 185.36 245.6 45524.42

Brick and Painting work

11 6.1A Brick work with bricks of class designation 100A in foundations and plinth in :

11.1 6.1.12/1 Cement mortar 1 .:4 (1 cement: 4 coarse sand ) Cum 256.2 5017.9 1285585.98

12 6.3A Extra for Brick work in superstructure above plinth level upto floor V cum Cum 39.468 842.2 33239.95

13 13.11 Cement plaster in course sand, 12 mm cement plaster of mix:

14 13.13 Cement plaster in course sand, 15 mm cement plaster of mix:

15 13.80 A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Sqm 1148.2 105.4 121020.28

16 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

16.1 13.46.1 New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) Sqm 1148.2 137 157303.4

17 13.94.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work Sqm 979.528 84.5 82770.12

18 10.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

18.1 10.16.1 Hot finished welded type tubes Kg 15950.58 123.9 1976276.86

19 10.32 Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

19.1 10.32.2 In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works. Kg 2571.914 114.6 294741.34

20 11.30.1 40 mm thick fine dressed stone flooring over 20 mm (average) thick base with joint finished fiush:base 1:5 (1 cement: 5 coarse sand )with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. Red Sand Stone Sqm 1536.09 849.2 1304443.38

21 8.13 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in Charge.

21.1 8.13.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. Sqm 363.348 3605.2 1309942.21

22 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite m 435.87 260.1 113369.79

23 7.36 Stone work ( machine cut edges veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) 25mm thick dressing of sand stone in veneer work Sqm 44.82 2563.8 114909.52

24 7.42 Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size,adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge. Each 90 265 23850

25 11.4 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. Sqm 13.91 1414 19669.00

26 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Sqm 44.13 789.9 34855.00

27 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm Sqm 9.00 1638.8 14749.00

28 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Sqm 2.40 1191.8 2860.00

11.77 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in charge. Sqm 347.00 721.1 250221.70

Door Window Work

29 9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately)

30 9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

30.1 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Sqm 5.04 2845.60 14341.82

31 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). Sqm 0.56 401.40 224.78

32 9.7 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :

32.1 9.7.7.1 Float glass panes 4 mm thick glass pane (weight not less than 10kg/sqm). Sqm 0.41 1242.40 503.17

33 9.62 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

34 9.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

35 9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. Each 2.00 108.10 216.20

36 9.81 Providing and fixing bright finished handle with necessary screws etc. complete :

37 9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. Each 2.00 639.40 1278.80

38 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Each 2.00 519.00 1038.00

39 9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). Each 12.00 130.00 1560.00

40 9.117.2 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge Extruded section profile size 42x50 mm metre 10.20 251.80 2568.36

40.1 9.118 Providing and fixing to existing door frames.

40.1.1 9.118.3 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places Sqm 3.78 2450.50 9263.00

41 9.147D.1 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

41.1 9.147d1.3 Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) Sqm 6.75 7074.9 47755.575

Sanitary Installations

42 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. Each 1 4470.9 4470.90

43 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid Each 1 4230 4230.00

44 17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern Each 2 3723.2 7446.40

45 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever requireWhite Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps Nos. 2 2764.4 5528.80

46 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Nos. 1 1068.5 1068.50

47 17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

47.1 17.70.2 Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms. Nos. 4 325.1 1300.40

48 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Ltr. 1000 9.7 9700.00

49.0 18.17.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 32 mm nominal bore. Each 1 589.9 589.90

50.0 18.18.2 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore

50.1 18.18.2 20mm nominal bore Each 1 397.4 397.40

50.2 18.18.3 25mm nominal bore Each 1 399.2 399.20

51.0 18.19.2 Providing and fixing gun metal non- return valve of approved quality (screwed end) :32 mm nominal bore Horizontal Each 2 677.6 1355.20

52 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in Charge.Internal work - Exposed on wall.

52.1 18.7.4 32 mm nominal outer dia Pipes Rmt. 500 395.2 197600.00

52.2 18.7.5 40 mm nominal outer dia Pipes Rmt. 5 538.4 2692.00

53 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

53.1 18.8.1 15 mm nominal outer dia Pipes Rmt. 40 278.2 11128.00

53.2 18.8.2 20 mm nominal outer dia Pipes Rmt. 5 350.8 1754.00

54 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore.15mm nominal bore. Nos 4 500.4 2001.60

55 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore.15mm nominal bore. Nos. 2 708.4 1416.80

56 18.58.1 Providing and fixing PTMT grating of approved quality and colour.Circular type.

57 12.78 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

(i) Single socketed pipes.

58 12.79 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

12.79.1 Coupler

12.79.2 Single pushfit Coupler

12.79.3 Single tee with door

12.79.6 Shoe (Plain)

59 19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

59.1 19.3.1 100 mm diameter S.W. pipe Rmt. 30 192.1 5763.00

60 19.30.1 Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

60.1 19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 1 4266.8 4266.80

60.2 19.31.1.1 Inside dimensions 455x 600 mm and 45 cm deep for pipe line with three or more inlets :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 extra beyond 45cm if brick masonary chamber Mtr. 1 3946.2 3946.20

61 19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

61.1 19.6.3 250 mm dia. RCC pipe metre 25 677.4 16935.00

62 12.43.2 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (110 mm)

PVC clips Each 6.00 182.72 1096

63 19.21 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete

63.1 19.21.1 For pipes 100 to 250 mm diameter Each 1.00 375.90 376

11.33.1 25 mm wooden planking, tongued and grooved in flooring including fixing with iron screws complete .2nd class teak wood Sqm 2.08 3991.8 8303

12.48. Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately) Sqm 9.00 292.1 2629

12.49 Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately) Sqm 0.68 20.5 14

NS Carraige of material

72 Coarse Sand (42 KM Koilwar) Cum 232.34 1194.92 277627.71

73 Stone chips (114Km) Manpur Cum 169.07 2430.87 410987.19

75 Stone Cum 9.8 0 0

77 Local Sand Cum 74.03 527.57 39056.01

A Total Cost of Part-I With 12% GST 12093738.21

B Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 648224.37

C Total (A+B) of Part-I With 18% GST 12741963

Vivekanand marg , Boring Road, Patna

Detailed Estimate for landscaping work of Chankya National Law University, Patna

Si.no. Rate Source Item N N L B/W H/D Qty Unit Rate Amount

Plinth Protection

4.17 Makingplinthprotection50mmthickof cement concrete1:3:6 (1 cement :3 coarse sand:6 graded stone aggregate 20mm nominal size)over75mm thick bed of dry brick ballast 40 mm nominal size, well rammedand consolidated and grouted with fine sand, including finishing the top smooth. Sqm

6.44 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). Metre

1 2.6.1 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.All Kind of Soil

Gate 2 to gate 3

For Pathway 1 1 450 1.2 0.3 162 Cum

Seating Area 1 1 161.72 0.375 0.825 50.03 Cum

Stone Chipping 1 1 125.76 0.95 0.225 26.88 Cum

For Plinth of guard Room 1 1 46.88 0.35 0.325 5.33 Cum

Total 348.64 Cum

Vip Guest House

For Pathway 1 1 227 0.75 0.3 51.08 Cum

Seating Area 1 1 22.15 0.375 0.8 6.65 Cum

Stone Chipping 1 1 22.65 0.95 0.225 4.84 Cum

For fountain 1 1 1.65 5.9 0.475 4.62 Cum

Total 69.22 Cum

Hostel & Playcourt & staff

For Pathway 1 1 511 1.2 0.3 183.96 Cum

Seating Area 1 1 252 0.625 0.8 126 Cum

Stone Chipping 1 1 109.47 0.95 0.225 23.4 Cum

Stone Chipping near Pathway 1 1 105.05 0.95 0.225 22.45 Cum

Fountain C 1 1 9.42 0.45 0.475 2.01 Cum

Fountain C 1 1 1.85 0.45 0.475 0.4 Cum

For fountain 1 1 1.65 5.9 0.475 4.62 Cum

Total 484.8 Cum

Gate 2 to gate 3

2 20.2.1 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 300mm dia pipe 1 12 5 60 Metre 902.6 54156

Gate 2 to gate 3

3 20.4.1 Extra over single under ream for providing additional bulbs in under reamed piles, under specified diameter(only the nos. of extra bulbs are to be paid)300 mm dia piles 12 Each 1621.6 19459.2

CC and RCC Work

6 4.1 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

6.1 4.1.3 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Gate 2 to gate 3

PCC below pathway 1 1 450 1.2 0.075 40.5 Cum

Seating Area 1 1 161.72 0.525 0.1 8.49 Cum

For Stone Chipping 1 1 125.76 0.95 0.075 8.96 Cum

For Stone Chipping 1 1 1.5 0.225 0.075 0.03 Cum

Floor 1 2 3 3 0.1 1.8 Cum

Vip Guest House

PCC below pathway 1 1 227 0.75 0.075 12.77 Cum Stone Chips 119.47

Seating Area 1 1 22.15 0.525 0.1 1.16 Cum

For Stone Chipping 1 1 22.65 0.95 0.075 1.61 Cum

Stone Work From Entry 1 1 16.8 3.8 0.1 6.38 Cum

For fountain 1 1 1.65 5.9 0.1 0.97 Cum

Total 23.49 Cum

Hostel & Playcourt & staff

PCC below pathway 1 1 511 1.2 0.075 45.99 Cum

Seating Area 1 1 252 0.625 0.1 15.75 Cum

Stone Chipping in hedge area 1 2 109.47 0.225 0.075 3.69 Cum

Stone Chipping near Pathway 1 1 105.05 0.225 0.075 1.77 Cum

Fountain C 1 1 9.42 0.45 0.1 0.42 Cum

Fountain C 1 1 1.884 0.45 0.1 0.08 Cum

Fountain C in floor 1 1 4.91 0.1 0.491 Cum

For fountain rec 1 1 1.65 5.9 0.1 0.97 Cum

Total 73.20 Cum

6.2 4.1.8 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size)

Gate 2 to gate 3

For Guard Romm Footing 1 12 1 1 0.1 1.2 Cum

Plinth of Guard Room 1 1 46.88 0.35 0.1 1.64 Cum

Vip Guest House

Hostel & Playcourt & staff

7 16.64 Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer-incharge.

Gate 2 to gate 3

In Pathway 1 1 450 1.2 540 Sqm

Seating Area 1 1 161.72 0.525 84.9 Sqm

Pergola 1 58 1 1 58 Sqm

Total 682.9 Sqm

Vip Guest House

In Pathway 1 1 227 0.75 170.25 Sqm

Seating Area 1 1 22.15 0.525 11.63 Sqm

From Entry 1 1 16.8 3.8 63.84 Sqm

Gazebo 1 4 1 1 4 Sqm

For fountain rec 1 1 1.65 5.9 9.74 Sqm

Total 259.46 Sqm

Hostel & Playcourt & staff

In Pathway 1 1 511 1.2 613.2 Sqm

Seating Area 1 1 252 0.625 157.5 Sqm

Pergola 4 14 1 1 56 Sqm

Fountain C 1 1 9.42 0.45 4.239 Sqm

Fountain C 1 1 1.884 0.45 0.8478 Sqm

Fountain C in floor 1 1 4.91 4.91 Sqm

paver 1 1 69.4 5 347 Sqm

For fountain rec 1 1 1.65 5.9 9.74 Sqm

Total 1193.44 Sqm

8 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Gate 2 to gate 3

For Stone Chipping 1 1 125.76 0.95 119.47 Sqm

Total 119.47 Sqm

Vip Guest House

For Stone Chipping 1 1 22.65 0.95 21.52 Sqm

Total 21.52 Sqm

Hostel & Playcourt & staff

For Stone Chipping 1 1 109.47 0.95 104 Sqm

For Stone chipping near pathway 1 1 105.05 0.95 99.8 Sqm

Total 203.8 Sqm

9 2.28 Supplying and Filling in plinth with local sand and under floors including,watering, ramming consolidating and dressing complete.

Gate 2 to gate 3

Pathway 1 1 15 0.95 0.15 2.14 Cum

Pergola 1 58 1 1 0.15 8.7 Cum

Stone Chipping 1 1 125.76 0.95 0.15 17.92 Cum

Guard Room plinth 2 1 46.88 0.35 0.15 4.92 Cum

Total 33.68 Cum

Vip Guest House

gazebo 1 4 1 1 0.15 0.6 Cum

Seating Area 1 1 22.15 0.375 0.15 1.25 Cum

Stone Chipping 1 1 22.65 0.95 0.15 3.23 Cum

For fountain 1 1 1.65 5.9 0.15 1.46 Cum

For fountain rec 1 1 1.65 5.9 0.15 1.46 Cum

Total 40.35 Cum

Hostel & Playcourt & staff

Pathway 1 1 15 0.95 0.15 2.14 Cum

pergola 4 14 1 1 0.15 8.4 Cum

Stone Chipping 1 1 109.47 0.95 0.15 15.6 Cum

Stone Chipping near Pathway 1 1 105.05 0.95 0.15 14.97 Cum

Seating Area 1 1 252 0.625 0.15 23.63 Cum

For fountain 1 1 1.65 5.9 0.15 1.46 Cum

For fountain rec 1 1 1.65 5.9 0.15 1.46 Cum

Total 67.66 Cum

10 5.1 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

10.1 5.1.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Gate 2 to gate 3

Pergola foundation 1 58 0.25 0.25 0.4 1.45 Cum

Pergola foundation 1 58 0.85 0.85 0.2 8.38 Cum

Plinth beam 1 1 46.88 0.35 0.25 4.1 Cum

Total 13.93 Cum

Vip Guest House

Gazebo foundation 1 4 0.25 0.25 0.4 0.1 Cum

Gazebo foundation 1 4 0.85 0.85 0.2 0.58 Cum

RCC tank bed 1 2 5.9 1.2 0.1 1.42 Cum

RCC tank Wall 1 2 5.9 0.35 0.1 0.41 Cum

Hostel & Playcourt & staff

Pergola foundation 4 14 0.25 0.25 0.4 1.4 Cum

Pergola foundation 4 14 0.85 0.85 0.2 8.09 Cum

RCC tank bed 1 2 5.9 1.2 0.1 1.42 Cum

RCC tank Wall 1 2 5.9 0.35 0.1 0.41 Cum

Total 11.32 Cum

Gate 2 to gate 3

11 5.2 Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

11.1 5.2.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

In Column 1 12 0.25 0.25 3 2.25 Cum

12 5.3 Reinforced cement conrete work in beams, suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Gate 2 to gate 3

In guard Room beam 1 1 46.88 0.25 0.25 2.93 Cum

Total 10.905 Cum

Hostel & Playcourt & staff

Seating Area 1 1 80 0.7 0.1 5.6 Cum

Gate 2 to gate 3

13 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete U.W.

13.2 5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Stirups in beam 4 376 0.9 0.395 534.672 Kg

13.3 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 8 116 0.8 0.62 460.288 Kg 92.6 42622.67

13.4 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia.

Guard Rooom 12 6 4.45 0.89 285.16 Kg

In Footing 12 12 1.65 0.89 211.46 Kg

13.5 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia.

Pergola 4 58 1 1.58 366.56 Kg

Vip Guest House

13.2 5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia.

13.3 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 8 8 0.8 0.62 31.744 Kg 92.6 2939.49

13.5 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia. 4 4 1 1.58 25.28 Kg 91.7 2318.18

Hostel & Playcourt & staff

13.2 5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Stirups in Column of pergola 4 4 0.76 0.395 4.8032 Kg

Seating 1 9 92 0.395 327.06 Kg

13.3 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 4 89 1.2 0.62 264.864 Kg 92.6 24526.41

13.4 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia.

Guard Rooom 1 4 4.45 0.89 15.84 Kg

In Footing 32 10 1.7 0.89 484.16 Kg

13.5 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia.

Pergola 4 56 1 1.58 353.92 Kg

14 5.9 Centring and shuttering including strutting,propping etc. and removal of form for.

Gate 2 to gate 3

14.1 5.9.1 Foundations, footings, bases of columns etc. for mass concrete

Pergola 4 58 1 0.25 58 Sqm

PCC below pathway 2 1 450 0.075 67.5 Sqm

Seating Area 2 1 161.72 0.1 32.344 Sqm

For Stone Chipping 2 1 125.76 0.075 18.864 Sqm

14.2 5.9.2 Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.

Total 0 Sqm 375.1 0.00

14.3 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts

Guard room 4 12 0.3 4 57.6 Sqm

14.4 5.9.21 Lintels, beams, plinth beams, girders, bressumers andcantilevers with water proof ply 12 mm thick.

Guard room beam 1 3 46.88 0.3 42.192 Sqm

14.5 5.9.20 Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick.

Guard Slab 2 1 7.25 8.8 127.6 Sqm

Vip Guest House

14.1 5.9.1 Foundations, footings, bases of columns etc. for mass concrete

Gazebo 4 4 1 0.25 4 Sqm

PCC below pathway 2 1 227 0.075 34.05 Sqm

Seating Area 2 1 22.15 0.1 4.43 Sqm

For Stone Chipping 2 1 22.65 0.075 3.3975 Sqm

RCC tank bed 1 2 5.9 0.15 1.77 Sqm

14.2 5.9.2 Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.

14.3 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts

Total 1.6 Sqm 494.4 791.04

Hostel & Playcourt & staff

14.1 5.9.1 Foundations, footings, bases of columns etc. for mass concrete

Pergola 4 56 1 0.25 56 Sqm

PCC below pathway 2 1 511 0.075 76.65 Sqm

Seating Area 2 1 252 0.1 50.4 Sqm

For Stone Chipping 2 1 109.47 0.075 16.4205 Sqm

RCC tank bed 1 2 5.9 0.15 1.77 Sqm

14.2 5.9.2 Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.

14.3 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts

Pergola 4 56 0.25 0.4 22.4 Sqm

Guard room 16 4 0.3 4 76.8 Sqm

14.4 5.9.21 Lintels, beams, plinth beams, girders, bressumers andcantilevers with water proof ply 12 mm thick.

Guard room beam 4 3 12 0.3 0 Sqm

Total 0 Sqm 518.9 0.00

14.5 5.9.20 Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick.

Seating 1 1 252 0.7 176.4 Sqm

15 4.11 Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Gate 2 to gate 3

Below Seating 1 1 161.72 0.375 60.65 Sqm

Guard Room beam 1 1 12 0.25 3 Sqm

Total 63.65 Sqm

Vip Guest House

Below Seating 1 1 22.15 0.375 8.31 Sqm

Hostel & Playcourt & staff

Below Planter 1 1 252 0.45 113.4 Sqm

Total 113.4 Sqm

Brick and Painting work

16 6.1A Brick work with bricks of class designation 100A in foundations and plinth in :

16.1 6.1.12/1 Cement mortar 1 .:4 (1 cement: 4 coarse sand )

Gate 2 to gate 3

Brick Work For Seating 1 1 161.72 0.375 0.9 54.58 Cum

Guard Room below plinth 1 1 46.88 0.25 0.45 5.27 Cum

Deduction of Door And Window -3 1 1.02 0.25 2.1 -1.61 Cum

Total 90.74 Cum

Vip Guest House

Brick Work For Seating 1 1 22.15 0.375 0.9 7.48 Cum

Total 15.59 Cum

Hostel & Playcourt & staff

Brick Work For Seating 1 1 252 0.45 0.9 102.06 Cum

Stone Chipping 1 2 109.47 0.075 0.25 4.11 Cum

Stone Chipping near Pathway 1 1 105.05 0.075 0.25 1.97 Cum

Fountain C 1 1 9.42 0.45 0.9 3.82 Sqm

Fountain C 1 1 1.884 0.45 0.9 0.76 Sqm

Total 149.87 Cum

17 6.3A Extra for Brick work in superstructure above plinth level upto floor V cum

Gate 2 to gate 3

Total 26.96 Cum

Vip Guest House

Total 6.254 Cum

Hostel & Playcourt & staff

Total 6.254 Cum

18 13.11 Cement plaster in course sand, 12 mm cement plaster of mix:

18.1 13..11.2 1:4(1 cement :4 coarse sand)

Gate 2 to gate 3

Brick Work For Seating 1 1 161.72 0.9 145.55 Sqm

Guard Room below plinth 1 1 12 0.15 1.8 Sqm

Room 2 1 12 2.75 66 Sqm

Deduction of Door And Window -2 1 1.02 2.1 -4.28 Sqm

Total 217.95 Sqm

Vip Guest House

Brick Work For Seating 1 1 22.15 0.9 19.94 Sqm

Total 44.02 Sqm

Hostel & Playcourt & staff

Brick Work For Planter Seating 1 1 252 1.25 315 Sqm

Stone Chipping 1 2 109.47 0.25 54.74 Sqm

Stone Chipping near Pathway 1 1 105.05 0.25 26.26 Sqm

Fountain C 1 1 9.42 0.9 8.48 Sqm

Fountain C 1 1 1.884 0.9 1.7 Sqm

Total 439.44 Sqm

19 13.13 Cement plaster in course sand, 15 mm cement plaster of mix:

19.1 13.12.2 1:4(1 cement :4 coarse sand)

Gate 2 to gate 3

Same As 12mm 217.95 Sqm

Total 217.95 Sqm

Vip Guest House

Same As 12mm 44.02 Sqm

Total 44.02 Sqm

Hostel & Playcourt & staff

Same As 12mm 124.44 Sqm

Total 124.44 Sqm

20 13.80 A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Gate 2 to gate 3

Same as Plaster Work 435.9 Sqm

ceiling 35.28 Sqm

Total 471.18 Sqm

Vip Guest House

Same as Plaster Work 88.04 Sqm

Total 88.04 Sqm

Hostel & Playcourt & staff

Same as Plaster Work 553.7 Sqm

ceiling 35.28 Sqm

Total 588.98 Sqm

21 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

21.1 13.46.1 New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Gate 2 to gate 3

Same as Putty 471.18 Sqm

Total 471.18 Sqm

Vip Guest House

Same as Putty 88.04 Sqm

Total 88.04 Sqm

Hostel & Playcourt & staff

Same as Putty 588.98 Sqm

Total 588.98 Sqm

22 13.94.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work

Gate 2 to gate 3

Painting on Gzaebo

100 x 50 x 4mm C Channel 2 2 11 0.125 5.5 Sqm

50 x 50 x 4mm MS Angle 2 18 0.75 0.1 2.7 Sqm

200 X 200 X 16mm plate 2 4 0.2 1.6 Sqm

Total 280.69 Sqm

Vip Guest House

Painting on Gzaebo

200 X 200 X 16mm plate 2 4 0.2 1.6 Sqm

Total 56.228 Sqm

Hostel & Playcourt & staff

Painting on Gzaebo

Pergola Over 3 seat

Pergola Behind Boys Toilet

100 x 50 x 4mm C Channel 4 56 11 0.125 308 Sqm

50 x 50 x 4mm MS Angle 4 28 0.75 0.1 8.4 Sqm

200 X 200 X 16mm plate 4 28 0.2 22.4 Sqm

Total 642.61 Sqm

Steel Work , Wooden floor and Roof Work

23 10.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Gate 2 to gate 3

23.1 10.16.1 Hot finished welded type tubes N N L U.W.

Total 7280.03 Kg

Hostel & Playcourt & staff

23.1 10.16.1 Hot finished welded type tubes

Pergola Over 3 seat

Pergola Behind Boys Toilet

Total 7713.3 Kg

24 10.32 Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

24.1 10.32.2 In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works.

Gate 2 to gate 3

100 x 50 x 4mm C Channel 1 2 11 6.01 132.22 Kg

Total 300.964 Kg

Hostel & Playcourt & staff

100 x 50 x 4mm C Channel 4 2 11 6.01 528.88 Kg

Total 2217.4 Kg

25 11.30.1 40 mm thick fine dressed stone flooring over 20 mm (average) thick base with joint finished fiush:base 1:5 (1 cement: 5 coarse sand )with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. Red Sand Stone

Gate 2 to gate 3

In Pathway 1 1 450 1.2 540 Sqm

Stone Over RCC tank Wall 1 1 3 3 9 Sqm

Total 612.84 Sqm

Vip Guest House

In Pathway 1 1 227 0.75 170.25 Sqm

Stone Work From Entry 1 1 16.8 3.8 63.84 Sqm

Stone Over RCC tank Wall 1 1 8.9 0.35 3.115 Sqm

Total 237.205 Sqm

Hostel & Playcourt & staff

In Pathway 1 1 511 1.2 613.2 Sqm

Stone Over RCC tank Wall 1 1 3 3 9 Sqm

Total 686.04 Sqm

26 8.13 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in Charge.

26.1 8.13.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Gate 2 to gate 3

Total 64.688 Sqm

Vip Guest House

Hostel & Playcourt & staff

Total 289.8 Sqm

27 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite

Gate 2 to gate 3

Vip Guest House

Hostel & Playcourt & staff

28 7.36 Stone work ( machine cut edges veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately)

Gate 2 to gate 3

Stone Cladding on face of fountain wall 1 2 11 0.45 9.9 Sqm

Vip Guest House

Stone Cladding on face of fountain wall 1 1 5.9 2.12 12.51 Sqm

Total 12.51 Sqm

Hostel & Playcourt & staff

Total 22.41 Sqm

29 7.42 Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size,adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.

Gate 2 to gate 3

8 pcs in 1 Sqm 1 90 90 Each

Vip Guest House

8 pcs in 1 Sqm 1 115 115 Each

Hostel & Playcourt & staff

8 pcs in 1 Sqm 1 90 90 Each

Gate 2 to gate 3

30 11.4 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

M toilet 1 1.00 3 3 9.00 Sqm

Gate 2 to gate 3

31 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

toilet 1 4.00 3 2.9 34.80 Sqm

Gate 2 to gate 3

32 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Guard room 1 1 3 3 9.00 Sqm

Gate 2 to gate 3

33 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Guard room 1 2 12 0.1 2.40 Sqm

Hostel & Playcourt & staff

34 13.46.1 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Fountain 1 1.00 4.91 4.91 Sqm

Hostel & Playcourt & staff

35 13.94.1 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Fountain 1 2.00 9.42 0.45 8.48 Sqm

Hostel & Playcourt & staff

36 11.77 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in charge.

Gate 2 to gate 3

Door Window Work

37 9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately)

37.1 9.1.2 .Sal wood

38 9.2 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

38.1 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Sqm

Guard Room 1 2.00 1.20 2.1 5.04 Sqm

39 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Guard Room 1 2.00 5.60 0.05 0.56 Sqm

40 9.7 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :

41 9.7.7.1 Float glass panes 4 mm thick glass pane (weight not less than 10kg/sqm). Sqm

Guard Room 1 2.00 0.45 0.45 0.41 Sqm

42 9.62 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

43 9.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

44 9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. 1 2.00 2 Each 108.1 216.20

44.1 9.81 Providing and fixing bright finished handle with necessary screws etc. complete :

47 9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. 2 1.00 2 Each 639.4 1278.80

48 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 1 2.00 2 Each 519 1038.00

49 9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). 2.00 6.00 12 Each 130 1560.00

Gate 2 to gate 3

50 9.117.2 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge Extruded section profile size 42x50 mm 1 2.00 5.10 10.2 metre 251.8 2568.36

51 9.118 Providing and fixing to existing door frames.

51.1 9.118.3 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places 1 2.00 0.90 2.1 3.78 Sqm 2450.5 9262.89

52 9.147D.1 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. 0 0.00

53 9.147d1.3 Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) 1 3.00 1.50 1.5 6.75 Sqm 7074.9 47755.58

54 Plumbing Work

54.1 Sanitary Installations

55 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Total 1 Each 4470.9 4470.90

56 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

In female Toilet 1 1 1 Each

Total 1 Each 4230 4230.00

57 17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

In male Toilet 1 2 2 Each

Total 2 Each 3723.2 7446.40

58 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever requireWhite Vitreous China Wash basin size 630x450 mmwith a pair of 15 mm C.P. brass pillar taps

Total 2 Each 2764.4 5528.80

59 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Total 1 Each 1068.5 1068.50

60 17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

60.1 17.70.2 Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms.

Total 4 Each 325.1 1300.40

Gate 2 to gate 3

61 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Toilet 1 1 1000 1000 Ltr

Total 1000 Ltr 9.7 9700.00

62 18.17.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 32 mm nominal bore.

Toilet 1 1 1 Each

Total 1 Each 589.9 589.90

63 18.18.2 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore

63.1 18.18.2 20mm nominal bore

Toilet 1 1 1 Each

Total 1 Each 397.4 397.40

63.2 18.18.3 25mm nominal bore

Toilet 1 1 1 Each

Total 1 Each 399.2 399.20

64 18.19.2 Providing and fixing gun metal non- return valve of approved quality (screwed end) :32 mm nominal bore Horizontal

Toilet 1 2 2 Each

Total 2 Each 677.6 1355.20

65 18.70 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in Charge.Internal work - Exposed on wall.

65.1 18.7.4 32 mm nominal outer dia Pipes

Toilet 1 1 500 500 Rmt.

65.2 18.7.5 40 mm nominal outer dia Pipes

Toilet 1 1 5 5 Rmt.

Total 5 Rmt. 538.4 2692.00

66 18.80 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

66.1 18.8.1 15 mm nominal outer dia Pipes

Toilet 1 1 40 40 Rmt.

66.2 18.8.2 20 mm nominal outer dia Pipes Rmt.

Toilet 1 1 5 5 Rmt.

Total 5 Rmt. 350.8 1754.00

67.0 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore.15mm nominal bore. 1 4 4 Nos 500.4 2001.60

68 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore.15mm nominal bore. 1 2 2 Nos 708.4 1416.80

69 18.58.1 Providing and fixing PTMT grating of approved quality and colour.Circular type.

69.1 18.58.1.1 100 mm nominal dia

In female Toilet 1 2 2 Each

Total 2 Each 33.2 66.40

Gate 2 to gate 3

70 12.78 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

(i) Single socketed pipes.

71 12.79 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler Each 120 120.00

100mm dia 1 1 1

Single pushfit Coupler Each 374.6 374.60

Single tee with door Each 193.4 193.40

Bend 87.5° Each 132 132.00

110 mm bend 1 1 1

Shoe (Plain) Each 115.95 115.95

110 mm Shoe 1 1 1

72 19.30 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : Rmt. 192.1 5763.00

72.1 19.3.1 100 mm diameter S.W. pipe 1 1 30.00 30

73 19.30.1 Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line : Each 4266.8 4266.80

73.1 19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1 1 1

74.0 19.31.1.1 Inside dimensions 455x 600 mm and 45 cm deep for pipe line with three or more inlets :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 extra beyond 45cm if brick masonary chamber Mtr. 3946.2 3946.20

75.0 19.60 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : metre 677.4 16935.00

76.0 12.43.2 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (110 mm)

For rain Water 2 3 6.00 Each 182.72 1096.32

77 19.21 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete

77.1 19.21.1 For pipes 100 to 250 mm diameter Each

External Sewareg and connection 1 1 1.00 Each 375.9 375.90

Vip Guest House

Steel Work , Wooden floor and Roof Work

78 10.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

78.1 10.16.1 Hot finished welded type tubes

Total 957.25 Kg

79 10.32 Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

79.1 10.32.2 In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works. Kg

MS Channel 75 X 40 C channel 1 2 3.75 7.14 53.55 Kg

80 11.33.1 25 mm wooden planking, tongued and grooved in flooring including fixing with iron screws complete .2nd class teak wood 1 1 3.2 0.65 2.08 Sqm 3991.8 8302.94

81 12.48. Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately) 1 4 1.5 1.5 9 Sqm 292.1 2628.90

82 12.49 Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately) 1 1 0.45 1.5 0.675 Sqm 20.5 13.84

NS Carraige of material

Gate 2 to gate 3

91 a Coarse Sand (42 KM Koilwar) Cum

In Brick Work 23.04796 Cum

Plaster 12mm 2.6572464 Cum

Plaster 15mm 3.321558 Cum

Stone Work 12.97178 Cum

92 b Stone Chips(114 KM) Manpur Cum

Stone Chips 6.46 Cum

Brick bats 51.2175 Cum

93 c Aggregate (114 KM) Manpur Cum

Total 0.00 0.00

Brick in Soiling 13.73905 Cum

Brick Work 90.74 Cum

Vip Guest House

a Coarse Sand (42 KM Koilwar)

In Brick Work 3.95986 Cum

Plaster 12mm 0.566692 Cum

Plaster 15mm 0.670865 Cum

Stone Work 5.020839 Cum

b Stone Chips (114 KM) Manpur

Stone Chips 2.15 Cum

Brick bats 18.729 Cum

c Aggregate (114 KM) Manpur

Flooring 9.4882 Cum

Cladding 0.31275 Cum

Total 9.8 Cum 0.00 0.00

Brick in Soiling 2.4748 Cum

Brick Work 15.59 Cum

Local Sand 40.35 Cum 527.57 21287.45

Hostel & Playcourt & staff

a Coarse Sand (42 KM Koilwar)

RCC 1:1.5:3 4.75 Cum

In Brick Work 38.07 Cum

Plaster 12mm 5.36 Cum

Plaster 15mm 1.90 Cum

Stone Work 14.52 Cum

b Stone Chips(114 KM) Manpur

Brick bats 90.51126 Cum

c Aggregate (114 KM) Manpur

Flooring 27.4416 Cum

Cladding 0.56025 Cum

Total 0 Cum 0 0.00

Brick in Soiling 23.437 Cum

Brick Work 149.87 Cum

Earth 67.66 Cum

A Total Cost of Part-I With 12% GST ₹ 12,093,738.32

B Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 ₹ 648,224.37

C Total (A+B) of Part-I With 18% GST ₹ 12,741,963.00 12794159.06

Horticulture 2597

83 23.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts.

Lawn- Gate 2 to Gate 3 1 1 259.7 10 2597 Sqm

Lawn- Vip 1 1 16 6 96 Sqm

Lawn_ Hostel 1 1 370 8 2960

84 23.2 Supplying and stacking of good earth at site including royalty and carriage for all leads. (earth measured in stacks will be reduced by 20% for payment).

Lawn- Gate 2 to Gate 3 1 1 259.7 10 0.121391 315.25 Cum

Lawn- Vip 1 1 16 6 0.05 4.8 Cum

Lawn_ Hostel 1 1 370 8 0.05 148 Cum

Deduction of remaining earth 0 Cum

85 23.4.3 Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of l.S. designation 4.75 mm

Lawn- Gate 2 to Gate 3 1 1 259.7 10 0.05 129.85 Cum

Lawn- Vip 1 1 16 6 0.05 4.80 Cum

Lawn_ Hostel 1 1 370 8 0.05 148 Cum

86 23.9 Mixing earth and sludge or manure in porportion specified or directed.

Lawn- Gate 2 to Gate 3 1 1 259.7 10 0.15 389.55 Cum

Lawn- Vip 1 1 16 6 0.15 14.4 Cum

Lawn_ Hostel 1 1 370 8 0.15 444 Cum

87 23.8 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Lawn- Gate 2 to Gate 3 1 1 259.7 10 0.15 389.55 Cum

Lawn- Vip 1 1 16 6 0.15 14.4 Cum

Lawn_ Hostel 1 1 370 8 0.15 444 Cum

88 23.10.3 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction.

Lawn- Gate 2 to Gate 3 1 1 259.7 10 2597 Sqm

Lawn- Vip 1 1 16 6 96 Sqm

Lawn_ Hostel 1 1 370 8 2960 Sqm

89 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) Cum

Gate 2 to Gate 3 1 1 150 10 0.15 225 Cum

90 23.14 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Each

90.1 23.14.1 Holes 1.2 m dia, and 1.2m deep 0 Each

90.2 23.14.2 Holes 60 cm dia, and 60 cm deep 0 Each

92 b Stone Chips(114 KM) Manpur Cum

Stone Chips 6.46 Cum

A Total Cost of Part-I With 12% GST ₹ 780,977.15

B Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 ₹ 41,860.38

C Total (A+B) of Part-I With 18% GST ₹ 822,837.53

Part II (DSR Horticulture 2020 and NSR Item)

97 DSR 2.57 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Each

97.1 DSR 2.57.1 Tree Plant 92 Each 7.3 671.60

97.2 DSR 2.57.2 Shrubs Plant 4433 Each 3.65 16180.45

97.3 DSR 2.57.3 Hedge Plant 0 Each 2.45 0.00

98 Horticulture DSR 2020 7.72 Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. 27 Each 65 1755.00

99 Horticulture DSR 2020 7.50 Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm.in big poly bag of size 25 cm as per direction of the officer-in-charge. 32 Each 120 3840.00

101 Horticulture DSR 2020 7.9 Providing and stacking of Bombax ceiba of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. 15 Each 70 1050.00

102 Horticulture DSR 2020 7.44 Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge. 18 Each 650 11700.00

103 Horticulture DSR 2020 6.12 Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 1481 Each 121 179201.00

104 Horticulture DSR 2020 8.30 Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3 4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge. 1120 Each 50 56000.00

105 Horticulture DSR 2020 8.53 Providing and stacking of Nerium oleander variegated of height 60-75 cm., multibranched in earthen pots of size 25 cm as per direction of the officer-in-charge. 550 Each 60 33000.00

106 Horticulture DSR 2020 8.63 Providing and stacking of Tabernaemontana coronaria (Chandni single) veriegated of height 105-120 cm., multibranched, bushy in big size HDPE bag as per direction of the officer-in-charge 1282 Each 110 141020.00

Seasonal Plants

107 Horticulture DSR 2020 4.90 Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. 120 Each 150.7 18084.00

107.1 Horticulture DSR 2020 4.90 Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 215 Each 150.7 32400.50

108 Horticulture DSR 2020 4.6 Providing and Displaying Asiatic lilly hybrid variety (3 in one) in each pot having in full bloom 3 to 5 flowers 30 to 45 cm ht. well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 475 Each 129.15 61346.25

109 Horticulture DSR 2020 4.49 Providing and Displaying Petunia hybrid different colour single well developed in full bloom in 20 cm Earthen/Plastic Pot and as per direction of the officer-in-charge. 385 Each 43.05 16574.25

110 Horticulture DSR 2020 4.29 Providing and Displaying Dianthus in different colour well developed with fresh & healthy foliage 30 cm ht., in full bloom with stacking in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in charge. 376 Each 54.35 20435.60

111 Horticulture DSR 2020 6.9 Providing and stacking of Chlorophytum-variegated, full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge 3120 Each 20 62400.00

112 Horticulture DSR 2020 6.31 Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 1600 Each 20 32000.00

113 Horticulture DSR 2020 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. 900 Each 20 18000.00

114 Horticulture DSR 2020 6.31 Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 985 Each 15 14775.00

115 Horticulture DSR 2020 6.2 Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 520 Each 20 10400.00

116 Horticulture DSR 2020 6.17 Providing and stacking of Iresine herbstii, of height 25-30 cm., full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge 400 Cum 20 8000.00

117 Horticulture DSR 2020, 2.28 Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. 1 2 54.68 3 328.08 Cum 456.35 149719.31

118 Horticulture DSR 2020, 2.50 Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. 1 3 22.65 0.95 0.1 6.46 Cum 610.7 3945.12

D Total Cost Without GST ₹ 892,498.08

F Total Cost with GST ₹ 1,053,147.73

G GRAND TOTAL (C+F) ₹ 14,617,948.26

Ar. Anand Saurabh -₹ 2.00

Vivekanand marg , Boring Road, Patna

Bill of Quantity

Si.no. Rate Source Item Unit Qty Rate Amount

1 2.29 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m all Kind of Soil 100 Sqm #REF! 1355.4 #REF!

2 2.6.1 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.All Kind of Soil Cum #REF! 314.9 #REF!

CC and RCC Work

3 4.1 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

3.1 4.1.3 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) Cum #REF! 3998.1 #REF!

4 4.1.8 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size) Cum #REF! 2975.2 #REF!

5 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l, Sqm #REF! 283.3 #REF!

6 2.28 Supplying and Filling in plinth with local sand and under floors including,watering, ramming consolidating and dressing complete. Cum #REF! 287.3 #REF!

7 5.1 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

7.1 5.1.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) Cum #REF! 4688.3 #REF!

8 5.2 Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

8.1 5.2.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) Cum #REF! 5670 #REF!

9 5.3 Reinforced cement conrete work in beams, suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size). Cum #REF! 5335.9 #REF!

10 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete

10.1 5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. Kg #REF! 94.5 #REF!

10.2 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. Kg #REF! 92.6 #REF!

10.3 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. Kg #REF! 90.8 #REF!

10.4 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia. Kg #REF! 91.7 #REF!

10.5 5.22.7E Thermo-Mechanically Treated bars TMT Fe-500-20mm dia. ky 91.70 Kg #REF! 91.7 #REF!

Centring, Shuttering and DPC Work

11 5.9 Centring and shuttering including strutting,propping etc. and removal of form for.

11.1 5.9.1 Foundations, footings, bases of columns etc. for mass concrete Sqm #REF! 211.6 #REF!

11.2 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts Sqm #REF! 494.4 #REF!

11.3 5.9.21 Lintels, beams, plinth beams, girders, bressumers andcantilevers with water proof ply 12 mm thick. Sqm #REF! 518.9 #REF!

11.4 5.9.20 Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick. Sqm #REF! 544.6 #REF!

12 4.2.3 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters,columns,piers, abutments, pillars,post. struts, buttresses, string or lacing courses,parapets, coping,bed blocks, anchor blocks, plin window sills, fillets etc. upt floor five level excluding the cost of centring,shuttering and finishing:1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) Cum #REF! 5128.3 #REF!

12.1 4.16A Extra for using 12.5/10 mm nominal size graded/single size stone aggregate instead of 20 mm nominal size graded stone aggregate in cement concrete/reinforced cement concrete 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size) Cum #REF! 56.1 #REF!

Brick, Plaster and Painting work

13 6.1A Brick work with bricks of class designation 100A in foundations and plinth in :

13.1 6.1.12/1 Cement mortar 1 .:4 (1 cement: 4 coarse sand ) Cum #REF! 5017.9 #REF!

14 6.3A Extra for Brick work in superstructure above plinth level upto floor V cum Cum #REF! 842.2 #REF!

15 6.18A+6.19A Half brick masonry with bricks of class designation 100A in foundations and plinth in :Extra for half Brick masonry in superstructure above pinth level upto floor V level Sqm #REF! 711.2 #REF!

16 6.21A Extra for half Brick masonry in superstructure above pinth level upto floor V level Sqm #REF! 113.6 #REF!

18 13.11 Cement plaster in course sand, 12 mm cement plaster of mix:

18.1 13..11.2 1:4(1 cement :4 coarse sand) Sqm #REF! 152.9 #REF!

19 13.13 Cement plaster in course sand, 15 mm cement plaster of mix:

19.1 13.12.2 1:4(1 cement :4 coarse sand) Sqm #REF! 176.4 #REF!

20 13.24 6 mm cement plaster to ceiling of mix :1:3(1 cement: 3 coarse sand) Sqm #REF! 131.3 #REF!

21 13.80 A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Sqm #REF! 105.4 #REF!

22 13.78.2 Applying one coat of cement primer of approved brand and manufacture on wall surface:Distemper primer Sqm #REF! 38.7 #REF!

23 13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications.

23.1 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Sqm #REF! 117.3 #REF!

24 13.45.1 Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm Sqm #REF! 215.2 #REF!

Steel Work and Flooring Work

25 10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes Kg #REF! 123.9 #REF!

26 16.3.3 Supplying and stacking at site.53 mm to 22.4 mm size stone aggregate Cum #REF! 883.7 #REF!

26.1 RA 1 Laying, spreading and stone aggregate of specified sizes to in uniform thickness, hand picking, in stages to proper grade and camber. As per direction of Engineer in Charge. Only Stone aggregate paid separatel. Cum #REF! 340.3 #REF!

A 11.4 52 mm thick cement concrete flooring with metallic concrete hardener topping under layer 40 mm thick cement concrete 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick metallic concrete hardener consisting of mix 1:2 (1 cement hardener mix:2 stone aggregate 6 mm nominal size) by volume @ 2 liter per 50 kg of cement or as per manufacture specification. This includes cost of cement slurry, etc. but excluding the cost of nosing of steps etc. complete. Sqm #REF! 472 #REF!

27 8.13 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in Charge.

27.1 8.13.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. Sqm #REF! 3605.2 #REF!

28 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite m #REF! 260.1 #REF!

29 11.4 be specified by the manufacturer) of 1st quality conforming to IS : 13755 of NITCO , ORIENT , SOMANY , KAJARIA or equivalent make in colours except white , Ivory , Grey , Fume , Red , Brown , laid on 20 mm thick cement motar 1:4 (1 cement: 4 Coarse sand) including grouting the joints with white cement and matching pigments etc, complete Sqm #REF! 1414 #REF!

30 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Sqm #REF! 789.9 #REF!

31 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm Sqm #REF! 1638.8 #REF!

32 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Sqm #REF! 1191.8 #REF!

33 11.19.2 Chequered terrazo tiles 22 mm thick with marble chips of sozes upto 6 mm in floors jointed with neat cement slurry mixed with pigement to match the shade of the tiles, including rubbing and polshing complete on 20 nm thick bed of cement mortar 1:4 (1 cement:4 coarse sand)Medium shade using 50% white cement and 50% ordinary cement Sqm #REF! 985.4 #REF!

Door Window Work

34 9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately)

34.1 9.1.2 .Sal wood Cum #REF! 95670.7 #REF!

35 9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

35.1 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Sqm #REF! 2845.6 #REF!

36 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). Sqm #REF! 401.4 #REF!

37 9.7 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :

37.1 9.7.7.1 Float glass panes 4 mm thick glass pane (weight not less than 10kg/sqm). Sqm #REF! 1242.4 #REF!

38 9.62 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

38.1 9.62.1 300x16 mm Each #REF! 169 #REF!

39 9.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

39.1 9.74.1 250x10mm Each #REF! 369.4 #REF!

40 9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. Each #REF! 108.1 #REF!

41 9.81 Providing and fixing bright finished handle with necessary screws etc. complete :

42 9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. Each #REF! 639.4 #REF!

43 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Each #REF! 810.1 #REF!

44 9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). Each #REF! 130 #REF!

45 9.117.2 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge Extruded section profile size 42x50 mm metre #REF! 251.8 #REF!

46 9.118 Providing and fixing to existing door frames.

46.1 9.118.3 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places Sqm #REF! 2450.5 #REF!

47 9.147D.1 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

48 9.147d.2 Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm). Sqm #REF! 9471 #REF!

49 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). Sqm #REF! 5143 #REF!

50 9.78 Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete. Each #REF! 920.4 #REF!

UPVC Door with Ventilator

51 147C Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

52 147C.2 Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm) Sqm #REF! 9892.7 #REF!

53 21.8.1 Filling the gap in between aluminium frame& adjacent RCC/Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width Sqm #REF! 85.2 #REF!

54 10.38.2 Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows all complete with. 5.5 mm thick glass panes. Sqm #REF! 1179.1 #REF!

UPVC Ventilator

55 9.147B Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable

56 9.147B.1 Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) Sqm #REF! 6690.7 #REF!

57 5.18 Providing,precast cement concrete Jali 1:2:4(1 cement:2 coarse sand:4 stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement:3 fine sand) etc.complete excluding plastering of the jambs, sills and soffits.40 mm thick Sqm #REF! 936.2 #REF!

Sanitary Installations

58 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. Each #REF! 4470.9 #REF!

59 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid Each #REF! 4230 #REF!

60 17.80 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre &post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Each #REF! 6534.2 #REF!

61 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever requireWhite Vitreous China Wash basin size 630x450 mmwith a pair of 15 mm C.P. brass pillar taps Each #REF! 2764.4 #REF!

62 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Each #REF! 1068.5 #REF!

63 17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

63.1 17.70.2 Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms. Each #REF! 325.1 #REF!

64 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Ltr #REF! 9.7 #REF!

65 18.17.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 32 mm nominal bore. Each #REF! 589.9 #REF!

66 18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore

66.1 18.18.2 20mm nominal bore Each #REF! 397.4 #REF!

66.2 18.18.3 25mm nominal bore Each #REF! 399.2 #REF!

67 18.19.2.1 Providing and fixing gun metal non- return valve of approved quality (screwed end) :32 mm nominal bore Horizontal Each #REF! 677.6 #REF!

68 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in Charge.Internal work - Exposed on wall.

68.1 18.7.4 32 mm nominal outer dia Pipes Rmt. #REF! 395.2 #REF!

68.2 18.7.5 40 mm nominal outer dia Pipes Rmt. #REF! 538.4 #REF!

69 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

69.1 18.8.1 15 mm nominal outer dia Pipes Rmt. #REF! 278.2 #REF!

69.2 18.8.2 20 mm nominal outer dia Pipes Rmt. #REF! 350.8 #REF!

70.0 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore.15mm nominal bore. Nos #REF! 500.4 #REF!

71 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore.15mm nominal bore. Nos #REF! 708.4 #REF!

72 18.58.1 Providing and fixing PTMT grating of approved quality and colour.Circular type.

72.1 18.58.1.1 100 mm nominal dia Each #REF! 33.2 #REF!

73 12.78 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.

73.1 12.78.2 110 mm diameter Mtr. #REF! 257.5 #REF!

74 12.79 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

12.79.1 Coupler

12.79.1.2 100mm dia Each #REF! 120 #REF!

12.79.2 Single pushfit Coupler

12.79.2.2 110 mm Each #REF! 374.6 #REF!

12.79.3 Single tee with door

12.79.5.2 110 mm bend Each #REF! 132 #REF!

12.79.6 Shoe (Plain)

12.79.6.2 110 mm Shoe Each #REF! 115.95 #REF!

75 19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

75.1 19.3.1 100 mm diameter S.W. pipe Rmt. #REF! 192.1 #REF!

76 19.30.1 Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

76.1 19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each #REF! 4266.8 #REF!

77.0 19.31.1.1 Inside dimensions 455x 600 mm and 45 cm deep for pipe line with three or more inlets :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 extra beyond 45cm if brick masonary chamber Mtr. #REF! 3946.2 #REF!

78.0 19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

78.1 19.6.3 250 mm dia. RCC pipe metre #REF! 677.4 #REF!

79.0 12.80.2 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (110 mm) Each #REF! 182.72 #REF!

80 19.21 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete

80.1 19.21.1 For pipes 100 to 250 mm diameter Each #REF! 375.9 #REF!

81 19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. Each #REF! 33603.4 #REF!

19.21.1 Carraige of material

83 a Coarse Sand (42 KM Koilwar) Cum #REF! 1194.92 #REF!

84 b Stone Chips(114 KM) Manpur Cum #REF! 2430.87 #REF!

85 c Aggregate (114 KM) Manpur Cum #REF! 2430.87 #REF!

86 d Stone Cum #REF! 0.00 #REF!

87 Brick Cum #REF! 958.51 #REF!

88 Local Sand Cum #REF! 527.57 #REF!

A Total Cost of Part-I With 12% GST #REF!

B Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 #REF!

C Total (A+B) of Part-I With 18% GST #REF! 12794159.06

Wiring Switches and Accessories

89 1.7 Wiring for circuit / submain wiring along with earth wire with the following sizes of FR PVC Insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

89.1 1.7.1 2x1.5 sq.mm +1x1.5 sq.mm earth wire metre #REF! 201 #REF!

89.2 1.7.2 2x2.5 sq.mm +1x2.5sq.mm earth wire metre #REF! 246 #REF!

89.3 1.7.3 2x4 sq.mm+ 1x4 sq.mm earth wire metre #REF! 309 #REF! ₹ 0.00 ₹ 3,875,218.8

89.4 1.7.12 2x10 sq.mm+ 1x6 sq.mm earth wire metre #REF! 925 #REF!

90 1.1 Wiring for light point / fan point / exhaust fan point/ call bell point with 1.5 sq.mm CU. FR PVC insulated copper conductor single core cable in surface /recessed PVC conduit, with modular switch, modular plate, suitable PVC Box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required. g c

90.1 1.1.1 Group-A each #REF! 756 #REF!

91 1.21 supplying and fixing of following size of medium class PVC conduit along with acceries in surface /recess including cutting the wall and making good the same in case of recess conduct as required.

91.1 1.21.1 20 mm meter #REF! 102 #REF!

91.2 1.21.2 25 mm meter #REF! 120 #REF!

92 1.16 supplying and fixing of following pair 0.5 sq.mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required. meter #REF! 42 #REF!

92.1 1.16.2 2 Pair meter #REF! 31 #REF!

93 1.17 supplying and drawing co-axial Tv cable Rg-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid snd protected with PVC sheath in the existing surface/ recessed PVC conduct as required.

93.1 1.1.1 Group A point #REF! 756 #REF!

94 1.28 supplying and fixing following modular base and cover plate on existing modular metal boxes etc. as required

94.1 1.28.1 1 or 2 module 75mmx 75mm) each #REF! 105 #REF!

94.2 1.28.2 3 Module (100mmx75mm) each #REF! 125 #REF!

94.3 1.28.4 6 Module (200mmx75mm) each #REF! 158 #REF!

94.4 1.28.5 8 Module (125mmx125mm) each #REF! 189 #REF!

94.5 1.28.6 12 Module (200mmx150mm) each #REF! 254 #REF!

95 1.24 Supplying and fixing following modular switch/ socket on the exiting modularplate & switch box including connections but excluding moduar plate etc. As require.

95.1 1.24.1 5/6 amps switch each #REF! 82 #REF!

95.2 1.24.3 16/20 A Switch each #REF! 139 #REF!

95.3 1.24.4 3 pin 10 amp socet outlet each #REF! 112 #REF!

95.4 1.24.5 6 pin 16/20 A socket outlet each #REF! 183 #REF!

95.5 1.23.6 Telephone socket outlet each #REF! 89 #REF!

95.6 1.23.7 TV antenna socket outlet each #REF! 74 #REF!

96 1.25 Supplying and fixing two modular stepped type electronic fan requlator on the existing modular plate switch box including connections but excluding modular plate etc.as required. each #REF! 358 #REF!

97 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. each #REF! 34 #REF!

98 1.27 Supplying and fixing following size /modules , G.I box alongwith modular base &cover plate for modular switches in recess etc. As required.

98.1 1.27.1 1 or 2 module 75mm x 75mm) each #REF! 234 #REF!

98.2 1.27.2 3 Module (100mmx75mm) each #REF! 266 #REF!

98.3 1.27.4 6 Module (200mmx75mm) each #REF! 345 #REF!

98.4 1.27.5 8 Module (125mmx125mm) each #REF! 402 #REF!

98.5 1.27.6 12 Module (200mmx150mm) each #REF! 501 #REF!

99 1.32 supplying and fixing suitable size G.I/PVC Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socketoutlet and 15/16 A modular switch, connections etc. As required each #REF! 531 #REF!

100 1.33 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box /wooden block including connections etc. As required. each #REF! 64 #REF!

101 1.34 Supplying and fixing brass battle/ angle holder including connection etc. As required. each #REF! 80 #REF!

102 1.35 Installation ,testing , Commissioning of wall bracket / ceiling fitting of all sizes and shapes containing upto two GLS/CFL/LEDlampper fitting , complete with all accessories including connections etc as required. each #REF! 72 #REF!

103 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230V, complete as required. each #REF! 351 #REF!

104 1.23.8 Bell Push each #REF! 61 #REF!

105 1.41 Installation, testing and commissioning of pre-wired ,fluresent fitting/ compact florescent fitting of all types, completes with all accessories and tube/lamp etc. Directly on ceiling /wall, including connections with 1.5 q.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. each #REF! 134 #REF!

106 1.49 Numberning of ceiling fan/ Exhaust fan/ florescent fitting as required. each #REF! 38 #REF!

107 1.5 Installation of exhaust fan in the exiting opening, including make good the damage, connection, testing, commissioning etc.as required. each #REF! 296 #REF!

108 2.9 Supplying and fixing following way, Horizental type three pole 7 neutral, sheet steel, MCB distributation board, 415V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar,earth bar, din bar, interconnections, power painted including earthing etc. as required. (but without MCB/RCCB/Isolator)

108.1 2.9.1 4 way (4+12),Double door Horizental type each #REF! 4184 #REF!

109 2.1 Supplying and fixing 5 to 32 A rating , 240/415V, 10 KA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. As require

109.1 2.12.1 Single pole (6 A to 32A) each #REF! 237 #REF!

109.2 2.12.2 32 A TPN each #REF! 1282 #REF!

110 8.17 supply and fixing of following sweep/sizes metallic blades, heavy duty, single phase, 230 V a.C Exhaust fan in exisiting opening including making good the damage, connection, testing and commissioning etc as required.

110.1 8.17.1 300 mm sweep each #REF! 2572 #REF!

111 6.1 Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

111.1 6.1.4 9/10 watt LED Lamp each #REF! 161 #REF!

112 5.1 Supplying and fix 4'x18 watt LED batten with minium effective 100 IM/w in ploycarbonet housing and complets with integrated electrinic driver etc directly on wall/ ceiling including connection with 1.5 sq.mm FRLS PVC insu;ated copper conductor etc. as required. each #REF! 521 #REF!

113 8.16 Supplying and fitting and fixing of 1400 mm sweep with service value (CM/MM) minimum 4.10, Air delivery minium 245 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FRLS PVC insuleted copper conductor etc as required each #REF! 2838 #REF!

114 5.9 Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required. each #REF! 2663 #REF!

115 5.11 Supplying and fixing wall mounted light bracket/ fixture made with polycarbonate suitable for single 9/10 watt LED lamp directly on wall including connections etc as required. ( But without lamp) each #REF! 1340 #REF!

D Total cost of Electrical Work #REF!

Part-I ( Bihar SOR 2022)

116 23.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts. 100Sqm #REF! 3418.2 #REF!

117 2.30.1 Ploughing the existing ground to a depth ot 15 cm to 25 cm and watering the same:All kinds of soil. 100Sqm #REF! 1348 #REF!

118 23.4.3 Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of l.S. designation 4.75 mm Cum #REF! 315.8 #REF!

119 23.9 Mixing earth and sjudge or manure in porportion specified or directed. Cum #REF! 20.9 #REF!

120 23.8 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). Cum #REF! 30.1 #REF!

121 23.10.3 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction. 100 Sqm #REF! 1027.4 #REF!

122 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) Cum #REF! 126.9 #REF!

123 23.14 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

123.1 23.14.1 Holes 1.2 m dia, and 1.2m deep Each #REF! 536.5 #REF!

123.2 23.14.2 Holes 60 cm dia, and 60 cm deep Each #REF! 69.3 #REF!

NS Carraige of material

124 Stone chips (114Km) Manpur Cum #REF! 2430.87 #REF!

E Total Cost of Part-I With 12% GST #REF!

F Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 #REF!

G Total (E+F) of Part-I With 18% GST #REF!

Part II (DSR Horticulture 2020 and NSR Item)

125 DSR 2.57 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

125.1 DSR 2.57.1 Tree Plant Each #REF! 7.3 #REF!

125.2 DSR 2.57.2 Shrubs Plant Each #REF! 3.65 #REF!

125.3 DSR 2.57.3 Hedge Plant Each #REF! 2.45 #REF!

126 Horticulture DSR 2020 7.72 Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. Each #REF! 65 #REF!

127 Horticulture DSR 2020 7.50 Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm.in big poly bag of size 25 cm as per direction of the officer-in-charge. Each #REF! 120 #REF!

128 Horticulture DSR 2020 7.9 Providing and stacking of Bombax ceiba of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. Each #REF! 70 #REF!

129 Horticulture DSR 2020 7.44 Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge. Each #REF! 650 #REF!

130 Horticulture DSR 2020 6.12 Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each #REF! 121 #REF!

131 Horticulture DSR 2020 8.30 Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3 4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge. Each #REF! 50 #REF!

132 Horticulture DSR 2020 8.53 Providing and stacking of Nerium oleander variegated of height 60-75 cm., multibranched in earthen pots of size 25 cm as per direction of the officer-in-charge. Each #REF! 60 #REF!

133 Horticulture DSR 2020 8.63 Providing and stacking of Tabernaemontana coronaria (Chandni single) veriegated of height 105-120 cm., multibranched, bushy in big size HDPE bag as per direction of the officer-in-charge Each #REF! 110 #REF!

Seasonal Plants

134 Horticulture DSR 2020 4.90 Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. Each #REF! 150.7 #REF!

135 Horticulture DSR 2020 4.90 Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. Each #REF! 150.7 #REF!

136 Horticulture DSR 2020 4.6 Providing and Displaying Asiatic lilly hybrid variety (3 in one) in each pot having in full bloom 3 to 5 flowers 30 to 45 cm ht. well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. Each #REF! 129.15 #REF!

137 Horticulture DSR 2020 4.49 Providing and Displaying Petunia hybrid different colour single well developed in full bloom in 20 cm Earthen/Plastic Pot and as per direction of the officer-in-charge. Each #REF! 43.05 #REF!

138 Horticulture DSR 2020 4.29 Providing and Displaying Dianthus in different colour well developed with fresh & healthy foliage 30 cm ht., in full bloom with stacking in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in charge. Each #REF! 54.35 #REF!

139 Horticulture DSR 2020 6.9 Providing and stacking of Chlorophytum-variegated, full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge Each #REF! 20 #REF!

140 Horticulture DSR 2020 6.31 Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each #REF! 20 #REF!

141 Horticulture DSR 2020 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. Each #REF! 20 #REF!

142 Horticulture DSR 2020 6.31 Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each #REF! 15 #REF!

143 Horticulture DSR 2020 6.2 Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each #REF! 20 #REF!

144 Horticulture DSR 2020 6.17 Providing and stacking of Iresine herbstii, of height 25-30 cm., full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge Each #REF! 20 #REF!

145 Horticulture DSR 2020, 2.28 Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. Cum #REF! 456.35 #REF!

146 Horticulture DSR 2020, 2.50 Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. Per Qtl. #REF! 610.7 #REF!

D Total Cost Without GST #REF!

E Add 18% GST #REF!

F Total Cost with GST #REF!

J Total Cost of Horticulture #REF!

Total Project Cost #REF!

Vivekanand marg , Boring Road, Patna

BOQ FOR IMPROVEMENT OF MAIN ENTRANCE GATE (GATE NO. 1) WITH SECURITY GUARD ROOM, IMPROVEMENT OF GATE NO. 3 & IMPROVEMENT OF MAIN ENTRANCE TO UNIVERSITY ADMINISTRATIVE BUILDING OF CHANAKYA LAW UNIVERSITY , MITHAPUR, PATNA

Detailed Measurment

Si.no. Rate Source Item Unit Qty Rate Amount

CIVIL - PART 1A

1 15.12 Dismantiling doors window sand clere storywindows (steel or wood) shutters including chowkhats, architrage, holdfasts etc. complete and stacking within 50 metres lead:

1.1 15.12.1 Of area beyond 3 sqm each 142.01 151.8 21557.12

1.2 15.12.2 Of area beyond 3 sqm each 5 208.8 1044

2 15.18 Dismantling steel work inbuilt up sections in angles, tees, flats and channels including all gusset plats,bolts,nuts,cutting hvets, welding etc. including dismem bering and stacking within 50 metres lead. kg 1021.21 2.3 2348.78

3 15.23 Dismantling tilework in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

3.1. 15.23.1 For thickness of tiles 10 mm to 25 mm Sqm 871.97 30.7 26769.48

4 15.25 Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. Sqm 13.49 106.7 1439.38

5 15.7 Demolishing brick work including stacking of serviceable material and disposal of unserviceable material within 50 meters lead:

5.1 15.7.4 In cement mortar Cum 87.86 823.7 72370.28

6 15.58A Demolishing R.C.C.work by mechanical means and stockpiling at designated location sand disposal of dismantled materials upto a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars. Cum 244.93 1397.8 342363.154

7 20.3 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).

7.2 20.3.2 400 mm dia piles Meter 288 2691 775008

8 20.4 Extra over single under ream for providing additional bulbs in under reamed piles, under specified diameter(only the nos. of extra bulbs are to be paid)300 mm dia piles

9 2.29 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m all Kind of Soil 100 Sqm 11.25 1355.4 15248.25

10 2.6.1 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.All Kind of Soil Cum 1242.86 314.9 391376.61

CC and RCC Work

11 4.1.6 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 40 mm nominal size) Cum 91.66 3279.8 300626.47 #NAME?

12 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l, Sqm 1239.18 283.3 351059.69 156706.41

13 2.28 Supplying and Filling in plinth with local sand and under floors including,watering, ramming consolidating and dressing complete. Cum 1046.78 287.3 300739.89

14 5.33A Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete

14.1 5.33A.1 All work upto plinth level. Cum 360.38 4756.9 1714291.62

14.2 5.33A.2.1 Walls columns, pillars, posts cind struts Cum 38.31 5293.5 202793.99

14.3 5.33A.2.2 Beams, planth beams, girders, bressumers, contilevers,Suspended floors lintels roofs and staircases including spiral staircases, shelves etc. Cum 100.65 5677.2 571410.18

15 5.33B Add or deduct for providing richer or leaner mixes respectively at all floor levels.

15.1 5.33B.1 Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C. Cum 499.34 164.5 82141.43

16 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete

16.1 5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. Kg 6820.95 94.5 644579.78

16.2 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. Kg 16091.719328 92.6 1490093.21

16.3 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. Kg 8950.24 90.8 812681.79

16.4 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia. Kg 21381.41 91.7 1960675.30

16.5 5.22.7E Thermo-Mechanically Treated bars (FE-500) 20mm dia. Kg 10444.24 91.7 957736.81

16.6 5.22.7F Thermo-Mechanically Treated bars TMT Fe-500-25rnm dia. Kg 11402.26 91.7 1045587.24

17 22.11 Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area respectively, second and fourth courses of roofing felt type 2 grade I (fibre base self finished bitumen felt) six and final courses of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm including preparation of surface, excluding grading, compete. Sqm 174.04 604.6 105224.58

18 22.23 Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in- Charge.

18.1 For vertical surface two coats @0.70 kg per sqm Sqm 22.33 406.2 9070.45

18.2 For horizontal surface one coat @1.10 kg per sqm. Sqm 155.62 311.5 48475.63

Centring and Shuttering and DPC

19 5.9 Centring and shuttering including strutting,propping etc. and removal of form for.

19.1 5.9.1 Foundations, footings, bases of columns etc. for mass concrete Sqm 170.29 211.6 36033.36

19.2 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts Sqm 375.56 494.4 185676.86

19.3 5.9.14 Extra for shuttering in circular work (20% of respective centring and shuttering items) Sqm 83.78 20.2 1692.36

19.4 5.9.21 Lintels, beams, plinth beams, girders, bressumers andcantilevers with water proof ply 12 mm thick. Sqm 832.74 518.9 432108.79

19.5 5.9.9 Arches,domes,vaults upto 6m span Sqm 143.31 558.1 79981.31

19.6 5.9.117 Cornices and mouldings Sqm 1.68 625.2 1050.34

19.7 5.9.20 Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick. Sqm 317.71 544.6 173024.87

20 DSR 25.2 Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be tiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge.(1) The elevational area of the scaffolding shall be measured for payment purpose.(2)The payment will be made once only for execution of all items for such works. Sqm 494.54 176.2 87137.95

21 4.2.3 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters,columns,piers, abutments, pillars,post. struts, buttresses, string or lacing courses,parapets, coping,bed blocks, anchor blocks, plin window sills, fillets etc. upt floor five level excluding the cost of centring,shuttering and finishing:1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) Cum 0 5128.3 0.00

Brick, Plaster and Painting work

22 6.1A Brick work with bricks of class designation 100A in foundations and plinth in :

22.1 6.1.12/1 Cement mortar 1 .:4 (1 cement: 4 coarse sand ) Cum 91.42 5017.9 458736.42

23 6.3A Extra for Brick work in superstructure above plinth level upto floor V cum Cum 17.29 842.2 14561.64

24 6.18A+6.19A Half brick masonry with bricks of class designation 100A in foundations and plinth in :Extra for half Brick masonry in superstructure above pinth level upto floor V level Sqm 28.39 711.2 20190.97

25 6.21A Extra for half Brick masonry in superstructure above pinth level upto floor V level Sqm 28.39 113.6 3225.104

26 6.1.12C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in Cement mortar 1.:4 (1 cement: 4 coarse sand ) Cum 188.28 5116.3 963296.96

27 6.3C Extra tor Brick work in superstructure above plinth level upto floor V Cum 17.29 842.2 14561.64

28 6.45.2 Half brick masonry with non modular fly ash bricks of class designation 10, conforming IS :12894, in superstructure above plinth and upto floor V level.Cement mortar 1 : 4 (1 cement : 4 coarse sand) Sqm 33.27 700.8 23315.62

29 6.38 Providing and laying Autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand).The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. Sqm 17.81 6233.2 111013.29

30 13.11 Cement plaster in course sand, 12 mm cement plaster of mix:

31 13.13 Cement plaster in course sand, 15 mm cement plaster of mix: #REF!

32 13.24 6 mm cement plaster to ceiling of mix :1:3(1 cement: 3 coarse sand) Sqm 337.77 131.3 44349.20

33 13.38.2 Extra for plastering on circular work not exceeding 6 m in radius :In two coats Sqm 337.77 29.1 9829.11

34 13.26 Neat cement punning Sqm 23.9 40.5 967.95

35 13.80 A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Sqm 1818 105.4 191617.20

36 13.78 Applying one coat of cement primer of approved brand and manufacture on wall surface:Distemper primer Sqm 1818 38.7 70356.6

37 13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications.

37.1 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Sqm 1818 117.3 213251.40

Same As Putty Work

38 13.45.1 Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm Sqm 1480.23 215.2 318545.50

Steel Work and Flooring Work

39 10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Kg 3050 123.9 377895.00

40 12.52.2 Grading roof for water proofing treatment with Cement concrete 1:2:4(1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) Sqm 1.71 3932.2 6724.06

41 8.13 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in Charge.

41.1 8.13.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. Sqm 170.08 3605.2 613172.42

42 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite m 241.37 260.1 62780.34

43 11.4 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. Sqm 1.44 1414 2036.16

44 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Sqm 16.7 789.9 13191.33

45 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm Sqm 41.52 1638.8 68042.98

46 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Sqm 5.33 1191.8 6352.29

47 7.33.2 Providing and fixing stone jaii 40 mm thick throghout(without sunking or moulding in jali slab) in cement mortar 1:3(1 cement: 3 coarse sand ) including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc.White sand stone Sqm 187.87 985.4 185127.10

47.1 16.3.9 Supplying and stacking at site. Good earth Cum 593.17 187.7 111338.01

48 8.12 Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm (avearage) thick base of cement mortar 1:4(1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. Sqm 821.36 2147.7 1764034.87

Door Window Work

49 26.86 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm, modulus of elasticity 900 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for Separately).

0 Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

50 26.88 Providing and fixing factory made single extruded WPC {Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers {wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm', modulus of elasticity 850 N/mm' and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk 5.5 screws, all as per direction of Engineer-In- Charge. {Note: stainless steel butt hinges and necessary 5.5 screws shall be paid separately)

51 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). Sqm 1.12 401.4 449.57

52 9.7 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :

52.1 9.7.7.1 Float glass panes 4 mm thick glass pane (weight not less than 10kg/sqm). Sqm 0.81 1242.4 1006.34

53 9.62 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

54 9.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

55 9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. Each 13 108.1 1405.30

56 9.81 Providing and fixing bright finished handle with necessary screws etc. complete :

57 9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. Each 2 639.4 1278.80

58 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Each 5 810.1 4050.50

59 9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). Each 30 130 3900.00

60 9.147D.1 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Gate 1 -6windowsindow Gate 2 -4windows

60.1 9.147d.2 Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm). Sqm 25.92 9471 245488.32

61 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). Sqm 18 5143 92574.00

62 9.78 Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete. Each 2 920.4 1840.80

63 21.8 Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

21.8.1 Upto 5mm depth and 5 mm width Mtr. 80 85.2 6816.00

UPVC Ventilator

64 9.147B Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable

64.1 9.147B.1 Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) Sqm 0.54 6690.7 3612.98

Plumbing Work 0

Sanitary Installations

65 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid Each 1 4230 4230.00

66 17.8 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre &post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Each 0 6534.2 0.00

67 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever requireWhite Vitreous China Wash basin size 630x450 mmwith a pair of 15 mm C.P. brass pillar taps Each 1 2764.4 2764.40

68 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Each 1 1068.5 1068.50

69 17.7 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

69.1 17.70.2 Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms. Each 1 325.1 325.10

70 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Ltr 1000 9.7 9700.00

71 18.17.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 32 mm nominal bore. Each 1 589.9 589.90

72 18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore

72.1 18.18.2 20mm nominal bore Each 1 397.4 397.40

72.2 18.18.3 25mm nominal bore Each 1 399.2 399.20

73 18.19.2.1 Providing and fixing gun metal non- return valve of approved quality (screwed end) :32 mm nominal bore Horizontal Each 2 677.6 1355.20

74 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in Charge.Internal work - Exposed on wall.

74.1 18.7.4 32 mm nominal outer dia Pipes Rmt. 30 395.2 11856.00

74.2 18.7.5 40 mm nominal outer dia Pipes Rmt. 0 538.4 0.00

75 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

75.1 18.8.1 15 mm nominal outer dia Pipes Rmt. 15 278.2 4173.00

75.2 18.8.2 20 mm nominal outer dia Pipes Rmt. 10 350.8 3508.00

76 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore.15mm nominal bore. Nos 2 500.4 1000.80

77 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore.15mm nominal bore. Nos 2 708.4 1416.80

78 18.58.1 Providing and fixing PTMT grating of approved quality and colour.Circular type.

78.1 18.58.1.1 100 mm nominal dia Each 1 33.2 33.20

79 12.78 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

(i) Single socketed pipes.

80 12.79 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

100mm dia Each 1 120 120.00

Single pushfit Coupler

Single tee with door

110 mm bend Each 5 132 660.00

110 mm Shoe Each 1 115.95 115.95

81 19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

81.1 19.3.1 100 mm diameter S.W. pipe Rmt. 30 192.1 5763.00

82 19.30.1 Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

82.1 19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 2 4266.8 8533.60

83 19.31.1.1 Inside dimensions 455x 600 mm and 45 cm deep for pipe line with three or more inlets :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 extra beyond 45cm if brick masonary chamber Mtr. 1 3946.2 3946.20

84 12.80.2 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (110 mm) Each 72 182.72 13155.84

85 19.21 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete

85.1 19.21.1 For pipes 100 to 250 mm diameter Each 1 375.9 375.90

86 19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. Each 1 33603.4 33603.40

87 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in charge. (Glazing, paneling and dash fasteners to be paid for separately) : 78.92 24.05

87.1 21.1.1.1 For fixed portion, Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

88 12.60.3 Extra for providing 3 mm thick translucent white acrylic plastic sheets of approved quality in false ceiling instead of 12 mm thick plain/or with design particle board ceiling tiles in item above.

19.21.1 Carraige of material

89 a Coarse Sand (42 KM Koilwar) 349.17 1194.92 417230.22

90 b Stone Chips(114 KM) Manpur 0 2430.87 0.00

91 c Aggregate (114 KM) Manpur 393.86 2430.87 957422.46

A Total Cost of Part-I With 12% GST ₹ 24,175,405.68

B Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 ₹ 1,295,801.74

C Total (A+B) of Part-I With 18% GST ₹ 25,471,207.00

CIVIL - PART 1B- SALVAGE

96 a Steel Quintal 50.62 5860 296633.20

97 b Brick Work 1000 nos 20 3800 76000.00

98 c Brick Bat cum 26.36 987 26017.32

99 d Door Window Below 3 Sqm nos 6 300 1800.00

100 e Glass Panel sqm 34 1750 59500.00

D Total Salvage (deduction) ₹ 459,950.52

E TOTAL CIVIL (C-D) ₹ 25,011,256.48

Horticulture - PART 2

1 2.30.1 Ploughing the existing ground to a depth ot 15 cm to 25 cm and watering the same:All kinds of soil. 100Sqm 0.3155 1348 425.29

2 23.4.3 Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of l.S. designation 4.75 mm Cum 4.73 315.8 1493.73

3 23.9 Mixing earth and sludge or manure in porportion specified or directed. Cum 29.0214 20.9 606.55

4 23.8 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). cum 31.55 30.1 949.66

5 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) Cum 4.73 126.9 600.24

F Total Cost of Part-I With 12% GST ₹ 4,075.47

G Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 ₹ 218.45

H Total (E+F) of Part-I With 18% GST ₹ 4,294.00

Part 2B (DSR Horticulture 2020 )

6 DSR 2.57 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

6.1 DSR 2.57.1 Tree Plant Each 14 7.3 102.20

6.2 DSR 2.57.2 Shrubs Plant Each 322 3.65 1175.30

7 Horticulture DSR 2020 7.72 Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. Each 4 400 1600.00

8 Horticulture DSR 2020 3.86 Providing and displaying of Schefflera green 3 in 1 well developed with fresh healthy and attractive foliage from having 45-60 cm height., in 25cm size eathen pot/plastic pot & per direction of the officer-in-charge Each 30 205 6150.00

9 Horticulture DSR 2020 3.45 Providing and displaying of Dracaena song of india (three in one) having ht. 60 cm and above, well developed, fresh and healthy with good foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 30 141.5 4245.00

10 Horticulture DSR 2020 8.53 Providing and stacking of Nerium oleander variegated of height 60-75 cm., multibranched in earthen pots of size 25 cm as per direction of the officer-in-charge. Each 20 60 1200.00

11 Horticulture DSR 2020 8.27 Providing and stacking of Ficus panda of height 60-90 cm, with 8-10 branches, and healthy foliage, bushy in big size HDPE bag as per direction of the officer-in-charge. Each 242 180 43560.00

Ornamental Plants

12 Horticulture DSR 2020 5.22 Providing and Displaying Ficus Nuda topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180to 210cm ht in 40 cm Cement Pot as per direction of the officer-in-charge. Each 10 2593.25 25932.50

13 Horticulture DSR 2020 6.25 Providing and stacking of Syghonium (Butterfly)variegated with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20cm. as per direction of the officer-in-charge. Each 250 30 7500.00

14 Horticulture DSR 2020 6.4 Providing and stacking of Asparagus sprengeri of ht.30cm to 45 cm full of leafy branches in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 250 20 5000.00

15 Horticulture DSR 2020, 2.28 Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. Cum 60 456.35 27381.00

16 Horticulture DSR 2020, 2.33 Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge. Sqm 31.55 214.4 6764.32

I Total Cost Without GST ₹ 130,610.32

K Total Cost with GST ₹ 154,120.00

L Total of Horticulture Work (H+K) ₹ 158,414.00

Electrical -PART 3

1 1.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with piano type switch, phenolic laminated sheet, suitable size M.S./PVC box etc as reouired.

2 1.7 Wiring for circuit / submain wiring along with earth wire with the following sizes of FR PVC Insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2.1 1.7.1 2x1.5 sq.mm +1x1.5 sq.mm earth wire each 104 201 20904.00

2.2 1.7.2 2x2.5 sq.mm +1x2.5sq.mm earth wire each 310 246 76260.00

2.3 1.7.3 2x4 sq.mm+ 1x4 sq.mm earth wire each 720 309 222480.00

3 1.21 supplying and fixing of following size of medium class PVC conduit along with acceries in surface /recess including cutting the wall and making good the same in case of recess conduct as required.

4 1.16 supplying and fixing of following pair 0.5 sq.mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required.

5 1.24 Supplying and fixing following modular switch/ socket on the exiting modularplate & switch box including connections but excluding moduar plate etc. As require.

5.1 1.24.1 5/6 amps switch each 60 82 4920.00

5.3 1.24.4 3 pin , 5/6 amps socket outlet each 6 112 672.00

5.4 1.24.5 6 pin, 15/16 amps socket outlet each 8 183 1464.00

5.5 1.24.6 Telephone socket outlet each 2 131 262.00

6 1.25 Supplying and fixing two modular stepped type electronic fan requlator on the existing modular plate switch box including connections but excluding modular plate etc.as required. each 4 358 1432.00

7 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. each 16 34 544.00

8 1.27 Supplying and fixing following size /modules , G.I box alongwith modular base &cover plate for modular switches in recess etc. As required.

8.1 1.27.1 1 or 2 module 75mm x 75mm) each 4 234 936.00

1.27.6 12 Module (200mmx150mm) each 6 501 3006.00

9 1.28 supplying and fixing following modular base and cover plate on existing modular metal boxes etc. as required

9.1 1.28.1 1 or 2 module 75mmx 75mm) each 4 105 420.00

9.2 1.28.2 3 Module (100mmx75mm) each 4 125 500.00

9.3 1.28.4 6 Module (200mmx75mm) each 6 158 948.00

1.49 Numberning of ceiling fan/ Exhaust fan/ florescent fitting as required. each 76 38 2888.00

10 1.49 Numberning of ceiling fan/ Exhaust fan/ florescent fitting as required. each 76 38 2888.00

11 1.5 Installation of exhaust fan in the exiting opening, including make good the damage, connection, testing, commissioning etc.as required. each 1 296 296.00

12 2.9 Supplying and fixing following way, Horizental type three pole 7 neutral, sheet steel, MCB distributation board, 415V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar,earth bar, din bar, interconnections, power painted including earthing etc. as required. (but without MCB/RCCB/Isolator)

12.1 2.9.1 4 way (4+12),Double door Horizental type each 2 4148 8296.00

12.2 2.9.2 6 way ( 4 + 18 ), Double door, horizontal type each 3 5132 15396.00

13 2.12 Supplying and fixing 240/415V, 10 KA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. As require

13.1 2.12.1 Single pole (6 A to 32A) each 60 237 14220.00

14 2.13 Supplying and fixing following rating, 2401475 volts, "C" curve, miniattlre circuit breaker suitable for lnductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

14.1 2.13.1 6 A to 32 A, double pole each 24 667 16008.00

15 8.17 Supply and fixing of following sweep/sizes metallic blades, heavy duty, single phase, 230 V a.C Exhaust fan in exisiting opening including making good the damage, connection, testing and commissioning etc as required.

16 6.1 Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

16.1 6.1.4 9/10 watt LED Lamp each 16 161 2576.00

17 5.1 Supplying and fix 4'x18 watt LED batten with minium effective 100 IM/w in ploycarbonet housing and complets with integrated electrinic driver etc directly on wall/ ceiling including connection with 1.5 sq.mm FRLS PVC insu;ated copper conductor etc. as required. each 8 521 4168.00

18 8.16 Supplying and fitting and fixing of 1400 mm sweep with service value (CM/MM) minimum 4.10, Air delivery minium 245 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FRLS PVC insuleted copper conductor etc as required each 4 2838 11352.00

19 5.7 Supplying and fixing recess mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

20 5.15 Supplying and fixing fotrlowing types LED Flood light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on poleibuilding including connection earthing the body etc as required.

21 7.4.1 Upto 35 sq. mm (CIamped with 1 mm thick saddte) each 600 43 25800.00

22 7.7 Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

23 9.14.1 Supplying and laying of following size DWC HDPE pipe lSl marked along with all accessories like socket, bend, couplers etc. conforming to lS 14930, Part ll complete with fitting and cutting, jointing etc. In the existing trench, complete as required.63 mm dia (OD-63 mm & lD-51 mm nominal) each 60 128 7680.00

M Total Cost of Electrical Work ₹ 852,406.00

GRAND TOTAL (E+L+M) ₹ 26,022,076.00

Name of Department Chanakya National Law University, Patna

Name of the Firm

Name of the Bidder

NIT No. Description of Works Estimated Cost Above / Below in Percentage Rate Quoted on Estimated Cost

25/2026-27 Dated 14.07.2026 Improvement of Main Entrance Gate (Gate No. 01) with Security Guard Room, Improvement of Gate No. 03 and Improvement of Main Entrance to University Administrative Building of CNLU, Patna. Rs. 2,60,22,076/-

Vivekanand marg , Boring Road, Patna

Bill of Quantity

Si.no. Rate Source Item Unit Qty Rate Amount

1 2.29 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m all Kind of Soil 100 Sqm 11.25 1355.4 15248.25

2 2.6.1 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.All Kind of Soil Cum 643.27 314.9 202565.72

CC and RCC Work

3 4.1 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

3.1 4.1.3 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) Cum 19.71 3998.1 78802.55

4 4.1.8 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size) Cum 15.89 2975.2 47275.93

5 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l, Sqm 160.52 283.3 45475.32

6 2.28 Supplying and Filling in plinth with local sand and under floors including,watering, ramming consolidating and dressing complete. Cum 1970.79 287.3 566207.97

7 5.1 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

7.1 5.1.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) Cum 42.48 4688.3 199158.98

8 5.2 Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

8.1 5.2.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) Cum 3.34 5670 18937.80

9 5.3 Reinforced cement conrete work in beams, suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size). Cum 26.52 5335.9 141508.07

10 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete

10.1 5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. Kg 2374.85 94.5 224423.14

10.2 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. Kg 0.00 92.6 0.00

10.3 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. Kg 0.00 90.8 0.00

10.4 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia. Kg 0.00 91.7 0.00

10.5 5.22.7E Thermo-Mechanically Treated bars TMT Fe-500-20mm dia. ky 91.70 Kg 0.00 91.7 0.00

Centring, Shuttering and DPC Work

11 5.9 Centring and shuttering including strutting,propping etc. and removal of form for.

11.1 5.9.1 Foundations, footings, bases of columns etc. for mass concrete Sqm 175.56 211.6 37148.50

11.2 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts Sqm 259.53 494.4 128311.63

11.3 5.9.21 Lintels, beams, plinth beams, girders, bressumers andcantilevers with water proof ply 12 mm thick. Sqm 100.93 518.9 52372.58

11.4 5.9.20 Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick. Sqm 150.30 544.6 81853.38

12 4.2.3 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters,columns,piers, abutments, pillars,post. struts, buttresses, string or lacing courses,parapets, coping,bed blocks, anchor blocks, plin window sills, fillets etc. upt floor five level excluding the cost of centring,shuttering and finishing:1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) Cum #REF! 5128.3 #REF!

12.1 4.16A Extra for using 12.5/10 mm nominal size graded/single size stone aggregate instead of 20 mm nominal size graded stone aggregate in cement concrete/reinforced cement concrete 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size) Cum #REF! 56.1 #REF!

Brick, Plaster and Painting work

13 6.1A Brick work with bricks of class designation 100A in foundations and plinth in :

13.1 6.1.12/1 Cement mortar 1 .:4 (1 cement: 4 coarse sand ) Cum 103.58 5017.9 519754.08

14 6.3A Extra for Brick work in superstructure above plinth level upto floor V cum Cum #REF! 842.2 #REF!

15 6.18A+6.19A Half brick masonry with bricks of class designation 100A in foundations and plinth in :Extra for half Brick masonry in superstructure above pinth level upto floor V level Sqm #REF! 711.2 #REF!

16 6.21A Extra for half Brick masonry in superstructure above pinth level upto floor V level Sqm #REF! 113.6 #REF!

18 13.11 Cement plaster in course sand, 12 mm cement plaster of mix:

19 13.13 Cement plaster in course sand, 15 mm cement plaster of mix:

20 13.24 6 mm cement plaster to ceiling of mix :1:3(1 cement: 3 coarse sand) Sqm 168.25 131.3 22091.23

21 13.80 A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Sqm 250.30 105.4 26381.62

22 13.78.2 Applying one coat of cement primer of approved brand and manufacture on wall surface:Distemper primer Sqm 250.30 38.7 9686.61

23 13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications.

23.1 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Sqm 250.30 117.3 29360.19

24 13.45.1 Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm Sqm #REF! 215.2 #REF!

Steel Work and Flooring Work

25 10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes Kg #REF! 123.9 #REF!

26 16.3.3 Supplying and stacking at site.53 mm to 22.4 mm size stone aggregate Cum #REF! 883.7 #REF!

26.1 RA 1 Laying, spreading and stone aggregate of specified sizes to in uniform thickness, hand picking, in stages to proper grade and camber. As per direction of Engineer in Charge. Only Stone aggregate paid separatel. Cum #REF! 340.3 #REF!

A 11.4 52 mm thick cement concrete flooring with metallic concrete hardener topping under layer 40 mm thick cement concrete 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick metallic concrete hardener consisting of mix 1:2 (1 cement hardener mix:2 stone aggregate 6 mm nominal size) by volume @ 2 liter per 50 kg of cement or as per manufacture specification. This includes cost of cement slurry, etc. but excluding the cost of nosing of steps etc. complete. Sqm 0.00 472 0.00

27 8.13 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in Charge.

27.1 8.13.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. Sqm 12.62 3605.2 45497.62

28 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite m 21.03 260.1 5469.90

29 11.4 be specified by the manufacturer) of 1st quality conforming to IS : 13755 of NITCO , ORIENT , SOMANY , KAJARIA or equivalent make in colours except white , Ivory , Grey , Fume , Red , Brown , laid on 20 mm thick cement motar 1:4 (1 cement: 4 Coarse sand) including grouting the joints with white cement and matching pigments etc, complete Sqm #REF! 1414 #REF!

30 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Sqm #REF! 789.9 #REF!

31 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm Sqm #REF! 1638.8 #REF!

32 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Sqm 0.00 1191.8 0.00

33 11.19.2 Chequered terrazo tiles 22 mm thick with marble chips of sozes upto 6 mm in floors jointed with neat cement slurry mixed with pigement to match the shade of the tiles, including rubbing and polshing complete on 20 nm thick bed of cement mortar 1:4 (1 cement:4 coarse sand)Medium shade using 50% white cement and 50% ordinary cement Sqm 492.70 985.4 485506.58

Door Window Work

34 9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately)

34.1 9.1.2 .Sal wood Cum #REF! 95670.7 #REF!

35 9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

35.1 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Sqm #REF! 2845.6 #REF!

36 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). Sqm #REF! 401.4 #REF!

37 9.7 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :

37.1 9.7.7.1 Float glass panes 4 mm thick glass pane (weight not less than 10kg/sqm). Sqm #REF! 1242.4 #REF!

38 9.62 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

38.1 9.62.1 300x16 mm Each #REF! 169 #REF!

39 9.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

39.1 9.74.1 250x10mm Each #REF! 369.4 #REF!

40 9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. Each #REF! 108.1 #REF!

41 9.81 Providing and fixing bright finished handle with necessary screws etc. complete :

42 9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. Each #REF! 639.4 #REF!

43 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Each #REF! 810.1 #REF!

44 9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). Each #REF! 130 #REF!

45 9.117.2 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge Extruded section profile size 42x50 mm metre #REF! 251.8 #REF!

46 9.118 Providing and fixing to existing door frames.

46.1 9.118.3 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places Sqm #REF! 2450.5 #REF!

47 9.147D.1 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

48 9.147d.2 Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm). Sqm #REF! 9471 #REF!

49 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). Sqm #REF! 5143 #REF!

50 9.78 Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete. Each #REF! 920.4 #REF!

UPVC Door with Ventilator

51 147C Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

52 147C.2 Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm) Sqm #REF! 9892.7 #REF!

53 21.8.1 Filling the gap in between aluminium frame& adjacent RCC/Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width Sqm #REF! 85.2 #REF!

54 10.38.2 Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows all complete with. 5.5 mm thick glass panes. Sqm #REF! 1179.1 #REF!

UPVC Ventilator

55 9.147B Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable

56 9.147B.1 Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) Sqm #REF! 6690.7 #REF!

57 5.18 Providing,precast cement concrete Jali 1:2:4(1 cement:2 coarse sand:4 stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement:3 fine sand) etc.complete excluding plastering of the jambs, sills and soffits.40 mm thick Sqm #REF! 936.2 #REF!

Sanitary Installations

58 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. Each #REF! 4470.9 #REF!

59 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid Each #REF! 4230 #REF!

60 17.80 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre &post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Each #REF! 6534.2 #REF!

61 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever requireWhite Vitreous China Wash basin size 630x450 mmwith a pair of 15 mm C.P. brass pillar taps Each #REF! 2764.4 #REF!

62 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Each #REF! 1068.5 #REF!

63 17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

63.1 17.70.2 Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms. Each #REF! 325.1 #REF!

64 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Ltr #REF! 9.7 #REF!

65 18.17.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 32 mm nominal bore. Each #REF! 589.9 #REF!

66 18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore

66.1 18.18.2 20mm nominal bore Each #REF! 397.4 #REF!

66.2 18.18.3 25mm nominal bore Each #REF! 399.2 #REF!

67 18.19.2.1 Providing and fixing gun metal non- return valve of approved quality (screwed end) :32 mm nominal bore Horizontal Each #REF! 677.6 #REF!

68 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in Charge.Internal work - Exposed on wall.

68.1 18.7.4 32 mm nominal outer dia Pipes Rmt. #REF! 395.2 #REF!

68.2 18.7.5 40 mm nominal outer dia Pipes Rmt. #REF! 538.4 #REF!

69 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

69.1 18.8.1 15 mm nominal outer dia Pipes Rmt. #REF! 278.2 #REF!

69.2 18.8.2 20 mm nominal outer dia Pipes Rmt. #REF! 350.8 #REF!

70.0 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore.15mm nominal bore. Nos #REF! 500.4 #REF!

71 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore.15mm nominal bore. Nos #REF! 708.4 #REF!

72 18.58.1 Providing and fixing PTMT grating of approved quality and colour.Circular type.

72.1 18.58.1.1 100 mm nominal dia Each #REF! 33.2 #REF!

73 12.78 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.

73.1 12.78.2 110 mm diameter Mtr. #REF! 257.5 #REF!

74 12.79 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

12.79.1 Coupler

12.79.1.2 100mm dia Each #REF! 120 #REF!

12.79.2 Single pushfit Coupler

12.79.2.2 110 mm Each #REF! 374.6 #REF!

12.79.3 Single tee with door

12.79.5.2 110 mm bend Each #REF! 132 #REF!

12.79.6 Shoe (Plain)

12.79.6.2 110 mm Shoe Each #REF! 115.95 #REF!

75 19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

75.1 19.3.1 100 mm diameter S.W. pipe Rmt. #REF! 192.1 #REF!

76 19.30.1 Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

76.1 19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each #REF! 4266.8 #REF!

77.0 19.31.1.1 Inside dimensions 455x 600 mm and 45 cm deep for pipe line with three or more inlets :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 extra beyond 45cm if brick masonary chamber Mtr. #REF! 3946.2 #REF!

78.0 19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

78.1 19.6.3 250 mm dia. RCC pipe metre #REF! 677.4 #REF!

79.0 12.80.2 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (110 mm) Each #REF! 182.72 #REF!

80 19.21 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete

80.1 19.21.1 For pipes 100 to 250 mm diameter Each #REF! 375.9 #REF!

81 19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. Each #REF! 33603.4 #REF!

19.21.1 Carraige of material

83 a Coarse Sand (42 KM Koilwar) Cum 906.21 1194.92 1082848.45

84 b Stone Chips(114 KM) Manpur Cum 0.00 2430.87 0.00

85 c Aggregate (114 KM) Manpur Cum 879.38 2430.87 2137658.46

86 d Stone Cum 0.00 0.00 0.00

A Total Cost of Part-I With 12% GST #REF!

B Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 #REF!

C Total (A+B) of Part-I With 18% GST #REF! 12794159.06

Wiring Switches and Accessories

89 1.7 Wiring for circuit / submain wiring along with earth wire with the following sizes of FR PVC Insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

89.1 1.7.1 2x1.5 sq.mm +1x1.5 sq.mm earth wire metre #REF! 201 #REF!

89.2 1.7.2 2x2.5 sq.mm +1x2.5sq.mm earth wire metre #REF! 246 #REF!

89.3 1.7.3 2x4 sq.mm+ 1x4 sq.mm earth wire metre #REF! 309 #REF! ₹ 0.00 ₹ 3,875,218.8

89.4 1.7.12 2x10 sq.mm+ 1x6 sq.mm earth wire metre #REF! 925 #REF!

90 1.1 Wiring for light point / fan point / exhaust fan point/ call bell point with 1.5 sq.mm CU. FR PVC insulated copper conductor single core cable in surface /recessed PVC conduit, with modular switch, modular plate, suitable PVC Box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required. g c

90.1 1.1.1 Group-A each #REF! 756 #REF!

91 1.21 supplying and fixing of following size of medium class PVC conduit along with acceries in surface /recess including cutting the wall and making good the same in case of recess conduct as required.

91.1 1.21.1 20 mm meter #REF! 102 #REF!

91.2 1.21.2 25 mm meter #REF! 120 #REF!

92 1.16 supplying and fixing of following pair 0.5 sq.mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required. meter #REF! 42 #REF!

92.1 1.16.2 2 Pair meter #REF! 31 #REF!

93 1.17 supplying and drawing co-axial Tv cable Rg-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid snd protected with PVC sheath in the existing surface/ recessed PVC conduct as required.

93.1 1.1.1 Group A point #REF! 756 #REF!

94 1.28 supplying and fixing following modular base and cover plate on existing modular metal boxes etc. as required

94.1 1.28.1 1 or 2 module 75mmx 75mm) each #REF! 105 #REF!

94.2 1.28.2 3 Module (100mmx75mm) each #REF! 125 #REF!

94.3 1.28.4 6 Module (200mmx75mm) each #REF! 158 #REF!

94.4 1.28.5 8 Module (125mmx125mm) each #REF! 189 #REF!

94.5 1.28.6 12 Module (200mmx150mm) each #REF! 254 #REF!

95 1.24 Supplying and fixing following modular switch/ socket on the exiting modularplate & switch box including connections but excluding moduar plate etc. As require.

95.1 1.24.1 5/6 amps switch each #REF! 82 #REF!

95.2 1.24.3 16/20 A Switch each #REF! 139 #REF!

95.3 1.24.4 3 pin 10 amp socet outlet each #REF! 112 #REF!

95.4 1.24.5 6 pin 16/20 A socket outlet each #REF! 183 #REF!

95.5 1.23.6 Telephone socket outlet each #REF! 89 #REF!

95.6 1.23.7 TV antenna socket outlet each #REF! 74 #REF!

96 1.25 Supplying and fixing two modular stepped type electronic fan requlator on the existing modular plate switch box including connections but excluding modular plate etc.as required. each #REF! 358 #REF!

97 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. each #REF! 34 #REF!

98 1.27 Supplying and fixing following size /modules , G.I box alongwith modular base &cover plate for modular switches in recess etc. As required.

98.1 1.27.1 1 or 2 module 75mm x 75mm) each #REF! 234 #REF!

98.2 1.27.2 3 Module (100mmx75mm) each #REF! 266 #REF!

98.3 1.27.4 6 Module (200mmx75mm) each #REF! 345 #REF!

98.4 1.27.5 8 Module (125mmx125mm) each #REF! 402 #REF!

98.5 1.27.6 12 Module (200mmx150mm) each #REF! 501 #REF!

99 1.32 supplying and fixing suitable size G.I/PVC Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socketoutlet and 15/16 A modular switch, connections etc. As required each #REF! 531 #REF!

100 1.33 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box /wooden block including connections etc. As required. each #REF! 64 #REF!

101 1.34 Supplying and fixing brass battle/ angle holder including connection etc. As required. each #REF! 80 #REF!

102 1.35 Installation ,testing , Commissioning of wall bracket / ceiling fitting of all sizes and shapes containing upto two GLS/CFL/LEDlampper fitting , complete with all accessories including connections etc as required. each #REF! 72 #REF!

103 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230V, complete as required. each #REF! 351 #REF!

104 1.23.8 Bell Push each #REF! 61 #REF!

105 1.41 Installation, testing and commissioning of pre-wired ,fluresent fitting/ compact florescent fitting of all types, completes with all accessories and tube/lamp etc. Directly on ceiling /wall, including connections with 1.5 q.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. each #REF! 134 #REF!

106 1.49 Numberning of ceiling fan/ Exhaust fan/ florescent fitting as required. each #REF! 38 #REF!

107 1.5 Installation of exhaust fan in the exiting opening, including make good the damage, connection, testing, commissioning etc.as required. each #REF! 296 #REF!

108 2.9 Supplying and fixing following way, Horizental type three pole 7 neutral, sheet steel, MCB distributation board, 415V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar,earth bar, din bar, interconnections, power painted including earthing etc. as required. (but without MCB/RCCB/Isolator)

108.1 2.9.1 4 way (4+12),Double door Horizental type each #REF! 4184 #REF!

109 2.1 Supplying and fixing 5 to 32 A rating , 240/415V, 10 KA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. As require

109.1 2.12.1 Single pole (6 A to 32A) each #REF! 237 #REF!

109.2 2.12.2 32 A TPN each #REF! 1282 #REF!

110 8.17 supply and fixing of following sweep/sizes metallic blades, heavy duty, single phase, 230 V a.C Exhaust fan in exisiting opening including making good the damage, connection, testing and commissioning etc as required.

110.1 8.17.1 300 mm sweep each #REF! 2572 #REF!

111 6.1 Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

111.1 6.1.4 9/10 watt LED Lamp each #REF! 161 #REF!

112 5.1 Supplying and fix 4'x18 watt LED batten with minium effective 100 IM/w in ploycarbonet housing and complets with integrated electrinic driver etc directly on wall/ ceiling including connection with 1.5 sq.mm FRLS PVC insu;ated copper conductor etc. as required. each #REF! 521 #REF!

113 8.16 Supplying and fitting and fixing of 1400 mm sweep with service value (CM/MM) minimum 4.10, Air delivery minium 245 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FRLS PVC insuleted copper conductor etc as required each #REF! 2838 #REF!

114 5.9 Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required. each #REF! 2663 #REF!

115 5.11 Supplying and fixing wall mounted light bracket/ fixture made with polycarbonate suitable for single 9/10 watt LED lamp directly on wall including connections etc as required. ( But without lamp) each #REF! 1340 #REF!

D Total cost of Electrical Work #REF!

Part-I ( Bihar SOR 2022)

116 23.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts. 100Sqm 5.578 3418.2 19066.72

117 2.30.1 Ploughing the existing ground to a depth ot 15 cm to 25 cm and watering the same:All kinds of soil. 100Sqm 5.578 1348 7519.14

118 23.4.3 Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of l.S. designation 4.75 mm Cum 27.89 315.8 8807.66

119 23.9 Mixing earth and sjudge or manure in porportion specified or directed. Cum 83.67 20.9 1748.7

120 23.8 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). Cum 83.67 30.1 2518.47

121 23.10.3 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction. 100 Sqm 5.578 1027.4 5730.84

122 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) Cum 10.125 126.9 1284.86

123 23.14 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

123.1 23.14.1 Holes 1.2 m dia, and 1.2m deep Each 0 536.5 0

123.2 23.14.2 Holes 60 cm dia, and 60 cm deep Each 0 69.3 0

NS Carraige of material

124 Stone chips (114Km) Manpur Cum 20.38 2430.87 49541.13

E Total Cost of Part-I With 12% GST 96217.52

F Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 5157.26

G Total (E+F) of Part-I With 18% GST 101375

Part II (DSR Horticulture 2020 and NSR Item)

125 DSR 2.57 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

125.1 DSR 2.57.1 Tree Plant Each 23 7.3 167.9

125.2 DSR 2.57.2 Shrubs Plant Each 265 3.65 967.25

125.3 DSR 2.57.3 Hedge Plant Each 0 2.45 0

126 Horticulture DSR 2020 7.72 Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. Each 5 65 325

127 Horticulture DSR 2020 7.50 Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm.in big poly bag of size 25 cm as per direction of the officer-in-charge. Each 7 120 840

128 Horticulture DSR 2020 7.9 Providing and stacking of Bombax ceiba of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. Each 6 70 420

129 Horticulture DSR 2020 7.44 Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge. Each 5 650 3250

130 Horticulture DSR 2020 6.12 Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 40 121 4840

131 Horticulture DSR 2020 8.30 Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3 4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge. Each 90 50 4500

132 Horticulture DSR 2020 8.53 Providing and stacking of Nerium oleander variegated of height 60-75 cm., multibranched in earthen pots of size 25 cm as per direction of the officer-in-charge. Each 95 60 5700

133 Horticulture DSR 2020 8.63 Providing and stacking of Tabernaemontana coronaria (Chandni single) veriegated of height 105-120 cm., multibranched, bushy in big size HDPE bag as per direction of the officer-in-charge Each 40 110 4400

Seasonal Plants

134 Horticulture DSR 2020 4.90 Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. Each 30 150.7 4521

135 Horticulture DSR 2020 4.90 Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. Each 20 150.7 3014

136 Horticulture DSR 2020 4.6 Providing and Displaying Asiatic lilly hybrid variety (3 in one) in each pot having in full bloom 3 to 5 flowers 30 to 45 cm ht. well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. Each 25 129.15 3228.75

137 Horticulture DSR 2020 4.49 Providing and Displaying Petunia hybrid different colour single well developed in full bloom in 20 cm Earthen/Plastic Pot and as per direction of the officer-in-charge. Each 36 43.05 1549.8

138 Horticulture DSR 2020 4.29 Providing and Displaying Dianthus in different colour well developed with fresh & healthy foliage 30 cm ht., in full bloom with stacking in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in charge. Each 40 54.35 2174

139 Horticulture DSR 2020 6.9 Providing and stacking of Chlorophytum-variegated, full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge Each 150 20 3000

140 Horticulture DSR 2020 6.31 Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 220 20 4400

141 Horticulture DSR 2020 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. Each 110 20 2200

142 Horticulture DSR 2020 6.31 Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 165 15 2475

143 Horticulture DSR 2020 6.2 Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 190 20 3800

144 Horticulture DSR 2020 6.17 Providing and stacking of Iresine herbstii, of height 25-30 cm., full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge Each 120 20 2400

145 Horticulture DSR 2020, 2.28 Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. Cum 60 456.35 27381

146 Horticulture DSR 2020, 2.50 Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. Per Qtl. 10 610.7 6107

D Total Cost Without GST 91660.7

E Add 18% GST 16498.926

F Total Cost with GST 108160

J Total Cost of Horticulture 209,535

Total Project Cost #REF!

Vivekanand marg , Boring Road, Patna

Detailed Measurment

Si.no. Rate Source Item N N L B/W H/D Qty Unit Rate Amount

15.25 Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

On Riser of step 1 1 4.57 0.17 0.78 Sqm 1.39 0.05

15.2 Demolishing cement concrete including disposal of material within 50 metre lead:

15.2.2 1:4:8 or leaner mix

15.7 Demolishing brick work including stacking of serviceable material and disposal of unserviceable material within 50 meters lead:

15.7.3 In lime mortar

15.7.4 In cement mortar

1 2.29 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m all Kind of Soil

Cost for per 100Sqm 11.25 100 Sqm 1355.4 15248.25

2 2.6.1 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.All Kind of Soil

Excavation of Soil/ Sand from ramp and Stair 1 2 41.45 3.86 0.82 262.4 Cum

Ramp and Planter Coloumn 6 7 1.2 1.2 1.2 72.58 Cum

Stair column 2 3 1.2 1.2 1.2 10.37 Cum

Circuler Column 1 6 1.5 1.5 1.2 16.2 Cum

For Brick Work below plinth 0 Cum 209

Excavation for Septic Tank 0 Cum

For Brick Edging 0 Cum

For Brick Edging 0 Cum

CC and RCC Work

3 4.1 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

3.1 4.1.3 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

4 4.1.8 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size)

Ramp and Planter Coloumn 6 7 1.2 1.2 0.1 6.05 Cum

Stair column 2 3 1.2 1.2 0.1 0.86 Cum

Circuler Column 1 6 1.2 1.2 0.1 0.86 Cum

Below Stair beam 1 1 14.4 0.35 0.1 0.5 Cum 4.39

Beam At Semi Circle 1 1 22.38 0.35 0.1 0.78 Cum 6.82

5 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Ramp and Planter Coloumn 6 7 1.2 1.2 60.48 Sqm

Stair column 2 3 1.2 1.2 8.64 Sqm

Circuler Column 1 6 1.5 1.5 13.5 Sqm

Below beam 2 7 4.42 0.35 21.66 Sqm

Below Stair beam 1 1 14.4 0.35 5.04 Sqm 4.39

Beam At Semi Circle 1 1 22.38 0.35 7.83 Sqm 6.82

6 2.28 Supplying and Filling in plinth with local sand and under floors including,watering, ramming consolidating and dressing complete.

Ramp and Planter Coloumn 6 7 1.2 1.2 0.1 6.05 Cum

Stair column 2 3 1.2 1.2 0.1 0.86 Cum

Circuler Column 1 6 1.5 1.5 0.1 1.35 Cum

Below beam 2 7 4.42 0.35 0.1 2.17 Cum

Below Stair beam 1 1 14.4 0.35 0.1 0.5 Cum 4.39

Beam At Semi Circle 1 1 22.38 0.35 0.1 0.78 Cum 6.82

On Room 0 0 0 0 0 0 Cum

7 5.1 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

7.1 5.1.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Ramp and Planter Coloumn 6 7 1.2 1.2 0.25 15.12 Cum

Stair column 2 3 1.2 1.2 0.25 2.16 Cum

Circuler Column 1 6 1.5 1.5 0.25 3.38 Cum

Ramp Coloumn 1 1 0.25 0.25 0.88 0.06 Cum 0.27

Planter Coloumn 2 1 0.25 0.25 1.23 0.15 Cum 0.37

Stair column 1 3 0.25 0.25 1.55 0.29 Cum

Circuler Column topi 6 3.14 0.225 0.225 2.45 2.34 Cum

Below beam 2 7 4.42 0.25 0.25 3.87 Cum

Below Stair beam 1 1 14.4 0.25 0.25 0.9 Cum 4.39

Beam At Semi Circle 1 1 22.38 0.25 0.25 1.4 Cum 6.82

8 5.2 Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement. 72.34

8.1 5.2.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) 8518.035

Circuler Column 6 3.14 0.225 0.225 3.5 3.34 Cum

9 5.3 Reinforced cement conrete work in beams, suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

roof Beam of Semi Circle 1 1 14.76 0.25 0.46 1.7 Cum 4.5 0.08 0.14

10 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete U.W.

10.1 5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Take 1.5% of the RCC Qty & multiply with sp Denesity 7850 1 1736 1.368 2374.848 Kg

10.2 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Total 0.00 Kg 92.6 0.00

10.3 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia.

Total 0.00 Kg 90.8 0.00

10.4 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia.

Total 0 Kg 91.7 0.00

10.5 5.22.7E Thermo-Mechanically Treated bars (FE-500) 20mm dia.

Total 0 Kg 91.7 0.00

Centring and Shuttering and DPC

11 5.9 Centring and shuttering including strutting,propping etc. and removal of form for.

11.1 5.9.1 Foundations, footings, bases of columns etc. for mass concrete

For Footing N N N

Ramp and Planter Coloumn 6 7 1.2 4 0.55 110.88 Sqm

Stair column 2 3 1.2 4 0.55 15.84 Sqm

Circuler Column 1 6 1.5 4 0.55 19.8 Sqm

Septic Tank 0 Sqm

For PCC below Brick Edging 0 Sqm

11.2 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts

Ramp Coloumn 1 1 0.25 4 0.88 0.88 Sqm 0.27

Planter Coloumn 2 1 0.25 4 1.23 2.46 Sqm 0.37

Stair column 1 3 0.25 4 1.55 4.65 Sqm

Circuler Column topi 6 3.14 0.45 4 5.95 201.78 Sqm

5.9.14 Extra for shuttering in circular work (20% of respective centring and shuttering items) Sqm 20.2

11.3 5.9.21 Lintels, beams, plinth beams, girders, bressumers andcantilevers with water proof ply 12 mm thick.

roof Beam of Semi Circle 2 1 14.76 0.71 20.96 Sqm 4.5 0 0.22

Guard Room Slab 2 2 5.79 0.71 16.44 Sqm 1.76 0 0.22

11.4 5.9.20 Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick.

0 0 Brick, Plaster and Painting work

13 6.1A Brick work with bricks of class designation 100A in foundations and plinth in :

13.1 6.1.12/1 Cement mortar 1 .:4 (1 cement: 4 coarse sand )

Brick Work For Planter

Planter Coloumn 2 1 21.03 0.25 0.98 10.3 Cum 6.41

18 13.11 Cement plaster in course sand, 12 mm cement plaster of mix:

18.1 13..11.2 1:4(1 cement :4 coarse sand)

Planter Coloumn 2 1 21.03 0.98 41.22 Cum 6.41

19 13.13 Cement plaster in course sand, 15 mm cement plaster of mix: 2 2 5 2.85 57

13.24 6 mm cement plaster to ceiling of mix :1:3(1 cement: 3 coarse sand) 1 3.14 7.32 7.32 168.25 Sqm 131.3 22091.23

21 13.80 A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

circular column 6 3.14 0.45 5.95 50.44

22 13.78 Applying one coat of cement primer of approved brand and manufacture on wall surface:Distemper primer 250.3 Sqm 38.7 9686.61

23 13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications.

23.1 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm.

Same As Putty Work 250.30 Sqm 117.3 29360.19

0 0 Steel Work and Flooring Work

11.4 52 mm thick cement concrete flooring with metallic concrete hardener topping under layer 40 mm thick cement concrete 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick metallic concrete hardener consisting of mix 1:2 (1 cement hardener mix:2 stone aggregate 6 mm nominal size) by volume @ 2 liter per 50 kg of cement or as per manufacture specification. This includes cost of cement slurry, etc. but excluding the cost of nosing of steps etc. complete. Sqm 472 0.00

27 8.13 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in Charge.

27.1 8.13.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

At Planter 1 2 21.03 0.3 12.62 Sqm

28 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite

32 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Total 0.00 Sqm 1191.8 0.00

33 11.19.2 Chequered terrazo tiles 22 mm thick with marble chips of sozes upto 6 mm in floors jointed with neat cement slurry mixed with pigement to match the shade of the tiles, including rubbing and polshing complete on 20 nm thick bed of cement mortar 1:4 (1 cement:4 coarse sand)Medium shade using 50% white cement and 50% ordinary cement

16.3.9 Supplying and stacking at site. Good earth 1 2 21.03 0.75 0.92 29.02 Cum 187.7 5447.05

0 19.21.1 Carraige of material

83 a Coarse Sand (42 KM Koilwar)

In Brick Work 26.31 Cum

Plaster 12mm 2.87 Cum

Plaster 15mm 3.58 Cum

Stone Work 1:4 10.27 Cum

Stone/Tile Work 1:3 12mm base 0.00 Cum

84 b Stone Chips(114 KM) Manpur Cum

Stone Chips 0 Cum

Brick bats 0 Cum

85 c Aggregate (114 KM) Manpur Cum

Total 0.00 0.00

Brick in Soiling 18.46 Cum

Brick Work 176.38 Cum

88 0 Local Sand

0 A Total Cost of Part-I With 12% GST ₹ 7,512,918.86

0 B Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 ₹ 402,692.45

0 C Total (A+B) of Part-I With 18% GST ₹ 7,915,611.00

116 23.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts.

117 2.30.1 Ploughing the existing ground to a depth ot 15 cm to 25 cm and watering the same:All kinds of soil.

118 23.4.3 Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of l.S. designation 4.75 mm

119 23.9 Mixing earth and sludge or manure in porportion specified or directed.

120 23.8 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

121 23.10.3 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction.

122 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

123 23.14 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

123.1 23.14.1 Holes 1.2 m dia, and 1.2m deep 0 Each

123.2 23.14.2 Holes 60 cm dia, and 60 cm deep 0 Each

124 b Stone Chips(114 KM) Manpur Cum

Stone Chips 20.38 Cum

E Total Cost of Part-I With 12% GST ₹ 96,217.53

F Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 ₹ 5,157.26

G Total (E+F) of Part-I With 18% GST ₹ 101,375.00

Part II (DSR Horticulture 2020 and NSR Item)

125 DSR 2.57 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Each

125.1 DSR 2.57.1 Tree Plant 23 Each 7.3 167.90

125.2 DSR 2.57.2 Shrubs Plant 265 Each 3.65 967.25

125.3 DSR 2.57.3 Hedge Plant 0 Each 2.45 0.00

126 Horticulture DSR 2020 7.72 Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. 5 Each 65 325.00

127 Horticulture DSR 2020 7.50 Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm.in big poly bag of size 25 cm as per direction of the officer-in-charge. 7 Each 120 840.00

128 Horticulture DSR 2020 7.9 Providing and stacking of Bombax ceiba of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. 6 Each 70 420.00

129 Horticulture DSR 2020 7.44 Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge. 5 Each 650 3250.00

130 Horticulture DSR 2020 6.12 Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 40 Each 121 4840.00

131 Horticulture DSR 2020 8.30 Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3 4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge. 90 Each 50 4500.00

132 Horticulture DSR 2020 8.53 Providing and stacking of Nerium oleander variegated of height 60-75 cm., multibranched in earthen pots of size 25 cm as per direction of the officer-in-charge. 95 Each 60 5700.00

133 Horticulture DSR 2020 8.63 Providing and stacking of Tabernaemontana coronaria (Chandni single) veriegated of height 105-120 cm., multibranched, bushy in big size HDPE bag as per direction of the officer-in-charge 40 Each 110 4400.00

Seasonal Plants

134 Horticulture DSR 2020 4.90 Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. 30 Each 150.7 4521.00

135 Horticulture DSR 2020 4.90 Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 20 Each 150.7 3014.00

136 Horticulture DSR 2020 4.6 Providing and Displaying Asiatic lilly hybrid variety (3 in one) in each pot having in full bloom 3 to 5 flowers 30 to 45 cm ht. well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 25 Each 129.15 3228.75

137 Horticulture DSR 2020 4.49 Providing and Displaying Petunia hybrid different colour single well developed in full bloom in 20 cm Earthen/Plastic Pot and as per direction of the officer-in-charge. 36 Each 43.05 1549.80

138 Horticulture DSR 2020 4.29 Providing and Displaying Dianthus in different colour well developed with fresh & healthy foliage 30 cm ht., in full bloom with stacking in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in charge. 40 Each 54.35 2174.00

139 Horticulture DSR 2020 6.9 Providing and stacking of Chlorophytum-variegated, full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge 150 Each 20 3000.00

140 Horticulture DSR 2020 6.31 Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 220 Each 20 4400.00

141 Horticulture DSR 2020 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. 110 Each 20 2200.00

142 Horticulture DSR 2020 6.31 Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 165 Each 15 2475.00

143 Horticulture DSR 2020 6.2 Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 190 Each 20 3800.00

144 Horticulture DSR 2020 6.17 Providing and stacking of Iresine herbstii, of height 25-30 cm., full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge 120 Cum 20 2400.00

145 Horticulture DSR 2020, 2.28 Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. 1 2 20 1.5 60 Cum 456.35 27381.00

146 Horticulture DSR 2020, 2.50 Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. 1 1 100 1 0.1 10 Cum 610.7 6107.00

G Total Cost Without GST ₹ 91,660.70

I Total Cost with GST ₹ 108,160.00

J Total of Horticulture Work (F+I) ₹ 209,535.00

K GRAND TOTAL (C+D+J) ₹ 8,125,146.00

Laying, spreading and stone aggregate of specified sizes to in uniform thickness, hand picking, in stages to proper grade and camber. As per direction of Engineer in Charge. Only Stone aggregate paid separatel.

Code Description Unit Quantity Rate Amountl

Details of cost for 1cum LABOUR

114 Beldar day 0.26 306 79.56

115 Coolie day 0.26 318 82.68

101 Bhisti day 0.26 332 86.32

Sundries L.S. 2.73 2.12 5.79

Add 1 % Water charges on "W" 2.54

Add 1 % Water charges on "W" 36.09

Add 15% CPOH on "Y" 43.95

Add Cess @ 1% on "Z" 3.37

Cost for 1 cum 340.3

Chanakya National Law University Nyaya Nagar, Mithapur, Patna-800001

Bill of quantity for landscaping work between Gate 2 to Gate 3, NW part of Libraray & near Playground

Si.no. Rate Source Item Unite Qty Rate Amount

Part-I ( Bihar SOR 2022)

64 23.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts. 100Sqm 62.72 3418.2 214389.5

65 23.2 Supplying and stacking of good earth at site including royalty and carriage for all leads. (earth measured in stacks will be reduced by 20% for payment). Cum 499 143.5 71606.5

66 23.4.3 Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of l.S. designation 4.75 mm Cum 313.6 315.8 99034.88

67 23.9 Mixing earth and sjudge or manure in porportion specified or directed. Cum 940.8 20.9 19662.72

68 23.8 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). Cum 940.8 30.1 28318.08

69 23.10.3 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction. 100 Sqm 62.72 1027.4 64438.53

70 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) Cum 225 126.9 28552.5

71 23.14 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

71.1 23.14.1 Holes 1.2 m dia, and 1.2m deep Each 0 536.5 0

71.2 23.14.2 Holes 60 cm dia, and 60 cm deep Each 0 69.3 0

NS Carraige of material

73 Stone chips (114Km) Manpur Cum 20.38 2430.87 49541.13

A Total Cost of Part-I With 12% GST 780977.15

B Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 41860.38

C Total (A+B) of Part-I With 18% GST 822838

Part II (DSR Horticulture 2020 and NSR Item)

78 DSR 2.57 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

78.1 DSR 2.57.1 Tree Plant Each 92 7.3 671.6

78.2 DSR 2.57.2 Shrubs Plant Each 4433 3.65 16180.45

78.3 DSR 2.57.3 Hedge Plant Each 0 2.45 0

79 Horticulture DSR 2020 7.72 Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. Each 27 65 1755

80 Horticulture DSR 2020 7.50 Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm.in big poly bag of size 25 cm as per direction of the officer-in-charge. Each 32 120 3840

81 Horticulture DSR 2020 7.9 Providing and stacking of Bombax ceiba of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. Each 15 70 1050

82 Horticulture DSR 2020 7.44 Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge. Each 18 650 11700

83 Horticulture DSR 2020 6.12 Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 1481 121 179201

84 Horticulture DSR 2020 8.30 Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3 4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge. Each 1120 50 56000

85 Horticulture DSR 2020 8.53 Providing and stacking of Nerium oleander variegated of height 60-75 cm., multibranched in earthen pots of size 25 cm as per direction of the officer-in-charge. Each 550 60 33000

86 Horticulture DSR 2020 8.63 Providing and stacking of Tabernaemontana coronaria (Chandni single) veriegated of height 105-120 cm., multibranched, bushy in big size HDPE bag as per direction of the officer-in-charge Each 1282 110 141020

Seasonal Plants

87 Horticulture DSR 2020 4.90 Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. Each 120 150.7 18084

88 Horticulture DSR 2020 4.90 Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. Each 215 150.7 32400.5

89 Horticulture DSR 2020 4.6 Providing and Displaying Asiatic lilly hybrid variety (3 in one) in each pot having in full bloom 3 to 5 flowers 30 to 45 cm ht. well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. Each 475 129.15 61346.25

90 Horticulture DSR 2020 4.49 Providing and Displaying Petunia hybrid different colour single well developed in full bloom in 20 cm Earthen/Plastic Pot and as per direction of the officer-in-charge. Each 385 43.05 16574.25

91 Horticulture DSR 2020 4.29 Providing and Displaying Dianthus in different colour well developed with fresh & healthy foliage 30 cm ht., in full bloom with stacking in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in charge. Each 376 54.35 20435.6

92 Horticulture DSR 2020 6.9 Providing and stacking of Chlorophytum-variegated, full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge Each 3120 20 62400

93 Horticulture DSR 2020 6.31 Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 1600 20 32000

94 Horticulture DSR 2020 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. Each 900 20 18000

95 Horticulture DSR 2020 6.31 Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 985 15 14775

96 Horticulture DSR 2020 6.2 Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 520 20 10400

97 Horticulture DSR 2020 6.17 Providing and stacking of Iresine herbstii, of height 25-30 cm., full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge Each 400 20 8000

98 Horticulture DSR 2020, 2.28 Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. Cum 328.08 456.35 149719.31

99 Horticulture DSR 2020, 2.50 Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. Per Qtl. 6.46 610.7 3945.12

D Total Cost Without GST 892498.08

F Total Cost with GST 1053148

Grand Total (C+F+G) Cost With 18% GST 1,875,986

Vivekanand marg , Boring Road, Patna

Detailed Estimate for landscaping work of Chankya National Law University, Patna

Si.no. Rate Source Item N N L B/W H/D Qty Unit Rate Amount

83 23.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts.

Lawn- Gate 2 to Gate 3 1 1 259.7 10 2597 Sqm

Lawn- Vip 1 1 16 6 96 Sqm

Lawn_ Hostel 1 1 370 8 2960

84 23.2 Supplying and stacking of good earth at site including royalty and carriage for all leads. (earth measured in stacks will be reduced by 20% for payment).

Lawn- Gate 2 to Gate 3 1 1 259.7 10 0.121391 315.25 Cum

Lawn- Vip 1 1 16 6 0.05 4.8 Cum

Lawn_ Hostel 1 1 370 8 0.05 148 Cum

Deduction of remaining earth 0 Cum

85 23.4.3 Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of l.S. designation 4.75 mm

Lawn- Gate 2 to Gate 3 1 1 259.7 10 0.05 129.85 Cum

Lawn- Vip 1 1 16 6 0.05 4.8 Cum

Lawn_ Hostel 1 1 370 8 0.05 148 Cum

86 23.9 Mixing earth and sludge or manure in porportion specified or directed.

Lawn- Gate 2 to Gate 3 1 1 259.7 10 0.15 389.55 Cum

Lawn- Vip 1 1 16 6 0.15 14.4 Cum

Lawn_ Hostel 1 1 370 8 0.15 444 Cum

87 23.8 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Lawn- Gate 2 to Gate 3 1 1 259.7 10 0.15 389.55 Cum

Lawn- Vip 1 1 16 6 0.15 14.4 Cum

Lawn_ Hostel 1 1 370 8 0.15 444 Cum

88 23.10.3 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction.

Lawn- Gate 2 to Gate 3 1 1 259.7 10 2597 Sqm

Lawn- Vip 1 1 16 6 96 Sqm

Lawn_ Hostel 1 1 370 8 2960 Sqm

89 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) Cum

Gate 2 to Gate 3 1 1 150 10 0.15 225 Cum

90 23.14 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

90.1 23.14.1 Holes 1.2 m dia, and 1.2m deep 0 Each

90.2 23.14.2 Holes 60 cm dia, and 60 cm deep 0 Each

92 b Stone Chips(114 KM) Manpur Cum

Stone Chips 20.38 Cum

A Total Cost of Part-I With 12% GST ₹ 780,977.15

B Add 6% GST beyound 12% GST (Multiplying factor- 0.0536 ₹ 41,860.38

C Total (A+B) of Part-I With 18% GST ₹ 822,837.53

Part II (DSR Horticulture 2020 and NSR Item)

97 DSR 2.57 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Each

97.1 DSR 2.57.1 Tree Plant 92 Each 7.3 671.60

97.2 DSR 2.57.2 Shrubs Plant 4433 Each 3.65 16180.45

97.3 DSR 2.57.3 Hedge Plant 0 Each 2.45 0.00

98 Horticulture DSR 2020 7.72 Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. 27 Each 65 1755.00

99 Horticulture DSR 2020 7.50 Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm.in big poly bag of size 25 cm as per direction of the officer-in-charge. 32 Each 120 3840.00

101 Horticulture DSR 2020 7.9 Providing and stacking of Bombax ceiba of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. 15 Each 70 1050.00

102 Horticulture DSR 2020 7.44 Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge. 18 Each 650 11700.00

103 Horticulture DSR 2020 6.12 Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 1481 Each 121 179201.00

104 Horticulture DSR 2020 8.30 Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3 4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge. 1120 Each 50 56000.00

105 Horticulture DSR 2020 8.53 Providing and stacking of Nerium oleander variegated of height 60-75 cm., multibranched in earthen pots of size 25 cm as per direction of the officer-in-charge. 550 Each 60 33000.00

106 Horticulture DSR 2020 8.63 Providing and stacking of Tabernaemontana coronaria (Chandni single) veriegated of height 105-120 cm., multibranched, bushy in big size HDPE bag as per direction of the officer-in-charge 1282 Each 110 141020.00

Seasonal Plants

107 Horticulture DSR 2020 4.90 Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. 120 Each 150.7 18084.00

107.1 Horticulture DSR 2020 4.90 Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 215 Each 150.7 32400.50

108 Horticulture DSR 2020 4.6 Providing and Displaying Asiatic lilly hybrid variety (3 in one) in each pot having in full bloom 3 to 5 flowers 30 to 45 cm ht. well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 475 Each 129.15 61346.25

109 Horticulture DSR 2020 4.49 Providing and Displaying Petunia hybrid different colour single well developed in full bloom in 20 cm Earthen/Plastic Pot and as per direction of the officer-in-charge. 385 Each 43.05 16574.25

110 Horticulture DSR 2020 4.29 Providing and Displaying Dianthus in different colour well developed with fresh & healthy foliage 30 cm ht., in full bloom with stacking in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in charge. 376 Each 54.35 20435.60

111 Horticulture DSR 2020 6.9 Providing and stacking of Chlorophytum-variegated, full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge 3120 Each 20 62400.00

112 Horticulture DSR 2020 6.31 Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 1600 Each 20 32000.00

113 Horticulture DSR 2020 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. 900 Each 20 18000.00

114 Horticulture DSR 2020 6.31 Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 985 Each 15 14775.00

115 Horticulture DSR 2020 6.2 Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 520 Each 20 10400.00

116 Horticulture DSR 2020 6.17 Providing and stacking of Iresine herbstii, of height 25-30 cm., full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge 400 Cum 20 8000.00

117 Horticulture DSR 2020, 2.28 Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. 1 2 54.68 3 328.08 Cum 456.35 149719.31

118 Horticulture DSR 2020, 2.50 Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. 1 3 22.65 0.95 0.1 6.46 Cum 610.7 3945.12

D Total Cost Without GST ₹ 892,498.08

F Total Cost with GST ₹ 1,053,147.73

G GRAND TOTAL (C+F) ₹ 1,875,985.26

Ar. Anand Saurabh