ADDN ALTN REPAIR TO QTRS OF OFFRS MD ACCN AT

Amount

Demolition of cement concrete (un-reinforced) in any floor n.exc 15cm thickness ( below or above ground level ) not otherwise specially provided including removal of rubbish out side complex (MOD land), complete all as specified.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) by using diamond saw blade cutting machine without damaging adjacent RCC structures not otherwise including removal of rubbish outside complex ( MOD land), complete all as specified.

M & L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.50mm graded stone aggregate) as in sub base of tiles, surface even and rough without using extra cement, complete all as specified.

M&L for 75 mm thick cement concrete 1:3:6 type C2 (using 20mm graded stone aggregate). Plinth protection laid to a slope of 1 in 24 in alternate basis system.Surfaces even and smooth without using extra cement Each bay shall not exceed 3m in length, 12mm wide & 75mm deep joint shall be formed between the bays which shall be filled with Mastic filling to full depth comprising a mixture of 1 part of heator hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume) complete all as specified and directed.

M&L reinforced cement concrete 1:1.5:3 type A-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall,landing, balconies, shelves and like including bonding agent , complete all as specified

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping). complete all as specified and directed.

M&L form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete, complete all as specified.

Supply and fix TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified.

All as per item 08 above but 6mm to 8mm dia for stirrups

Demolition of brick work built in cement mortar in any description and position, complete all as specified.

M&L for brick work with sub class 'B' brick straight or curved on plan exc 6 metre mean radius with old size bricks, built in cement mortar 1:6, complete all as specified.

All as per item no 11 before but except bricks

M&L for brick work with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls with old size bricks, built in cement mortar 1:4, complete all as specified.

M&L for cement concrete 1:2:4 type B1(using 20mm graded stone aggregate) as in blocks for hold fast, coping, benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces, complete all as specified upto six storey height.

Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) mixed with WPC finished even and fair etc complete all as specified and directed.(Note:- WPC shall be measured and paid seperately.)

M&L rendering 10 mm thick in CM 1:6 on internal brick/concrete wall surfaces of any description, and finishing the surfaces even and fair without using extra cement complete all as specified and directed .

Supply only integral water proofing admixture of approved quality.

M&L for Preparation of old decorated surface (Plastered or unplastered) of ceiling by brooming down or steel wire brushing scraping down smook root mould moss and efforescent salts and treating oil and greasy spots as applicable and applying two coat of white wash complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and fair without using extra cement complete all as specified and directed.

M&L complete removal of existing treatment of old surface of ceiling and applying two coat of oil bound distemper over a coat of 1 to 2 mm thick waterproof wall care putty on ceiling complete all as specified and directed

M&L prepration on new plastered surfaces of ceiling with two coat of oil bound distemper over a coat of 1 to 2mm thick waterproof wall care putty on ceiling on plastered surfaces, preparatory to distempering complete all as specified and directed

M&L for Preparation of old decorated surfaces(Plastered or unplastered) of wall including cornices, pillasters etc by complete removal of existing treatment and applying two coats of white lime washing, complete all as specified.

M&L for preparation of the newly plastered surfaces of walls applying waterproof wall care putty of 1-2 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats of oil emulsion distemper (OBD), of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

M&L for preparation of the old plastered surfaces of walls applying waterproof wall care putty of 1-2 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats of oil emulsion distemper (OBD), of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

M&L resecuring or Easing and adjusing without taking down of doors for easy opening /closing ,tightening of hinges and changing its position or adjustment of tower bolts/sliding bolts etc area exc. 1sqm but not exc. 2 sqm each,complete all as specified and directed.

M&L for 2nd class hardwood plain, solid straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, complete all as specified.

Taking down chowkats or frames n.exc 1.5 sqm each with shutters (without taking off shutters from frames), complete all as specified.

Taking down chowkats or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames ), complete all as specified.

Taking down shutter of any description exc 1 sqm and not exc 2 sqm each, complete all as specified.

Taking down shutter of any description exc 1 sqm and not exc 2 sqm each, and refixing in same opening complete all as specified.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: -For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. Note:- Contractor will provide manufacturer test certificate alognwith screw out test certificate.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges shall be paid separately under relevant item). Note:- Contractor will provide manufacturer test certificate alognwith screw out test certificate.

S&F double riveted Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge.Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. Note:- Contractor will provide manufacturer test certificate alognwith screw out test certificate.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 50x 100 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge.Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. Note:- Contractor will provide manufacturer test certificate alognwith screw out test certificate.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges shall be paid separately under relevant item). Note:- Contractor will provide manufacturer test certificate alognwith screw out test certificate.

Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof,fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardwares shouldbe fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings.” Note: Fixture/fittings shall be measured & paid under relevant item Note:- Contractor will provide manufacturer test certificate alognwith screw out test certificate.

S&F mild steel work as in hold fast 25x3mm flat iron and similar articles conforming to Fe-410-0, complete all as specified.

Dismantling boarding any description (board/plywood) fixed in any position with screw, complete all as specified

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen & Cabinets.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen and Cabinets.

S&F 100 mm long (size) butt hinges, stainless steel 304 grade hinges, complete all as specified.

S&F 75 mm long (size) butt hinges, stainless steel 304 grade hinges, complete all as specified.

S&F 75 mm long L Bihari concealed type hinges incl stainless screw complete all as specified. Make: Hettich, Godrej, Ozone, Kich

S & F in repairs 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, complete all as specified.

S&F 300mm long, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified.

S&F in repair 300mm long, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified.make-

S&F 300mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and fixed, complete all as specified and directed.

S&F 250mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and fixed, complete all as specified and directed.

S&F 150mm long stainless steel barrel tower bolt of extruded section, complete all as specified.

S&F 200mm long stainless steel barrel tower bolt of extruded section, complete all as specified.

S & F in repair 200mm long (size) aluminium anodised, barrel tower bolt of extruded section and fixed, complete all as specified.

S&F 150mm size extruded aluminium alloy handle, fabricated type, anodised, complete all as specified.

S&F 150mm size stainless steel AISI 304 grade fancy type handle complete all as specified and directed.

S&F stainless steel AISI 304 grade floor door stopper with hard drawn steel spring 140mm long complete all as specified and directed.

S&F stainless steel Hasp and staple, 100mm size, safety type, brass with stainless steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified.

S&F 150x100mm concealed type SS handle for kitchen cup boards shutters, cabinets, crocery shelf drawers fixed with nuts , screw and washer of mild steel bright finished , complte all as specified.

S&F ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed, complete all as specified.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18 mm and fixed with steel wire staples, complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18 mm and fixed stainless steel wire staple, complete all as specified and directed.

S&F 4.00 mm thick plain sheet glass with PVC beading, aluminium beads, in square n.exc 0.5 Sqm in each pane, complete all as specified.

S&F 4.00 mm thick figured glass, pin head type and glazing with glass putty, PVC beading, aluminium beads, complete all as specified

S&F 5.5 mm thick sheet glass ordinary quality in square n.exc 0.5 Sqm each including grinding of edges for crockery cupboard including taking out/ broken glass with roller, complete all as specified.

S&F mild steel 150mm ordinary rat tail , rod pattern springs including roller and roller plate complete all as specified

S&F in repair mild steel 150mm ordinary rat tail , rod pattern springs including roller and roller plate complete all as specified

S&F MS sliding arregment /roller fixed with 5.50 mm thick sheet glass "C" shape staple, chromium plated f complete allas specified

S&F Stainless steel drapery curtain rods gold or antique silver 25 mm nominal dia and minimum thickness 1.2mm of SS-304 Grade of approved quality with two number decorative brackets design as approved fixed in brick/concrete wall with same finished knobs/latto on each end of curtain rod incl taking down old pelmet complete all as required and directed.

M&L for Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

M&L for Preparation of old painted surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, all as specified.

M&L for coloured ceramic tiles of size 600x600x 7 to 8mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement over 15mm thick screed bed in CM 1:4 complete all as directed. Note : Vitrified tiles can be used in lieu of ceramic tiles as no cost basis.

All asper item No- 71 above but as in skirting etc, including 10 mm thick rendering in CM 1:3, complete all as specified.

S & F for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 600x300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick screed bed in cement mortar (1:3) complete all as specified and as directed.

M&L for double charged Vitrified tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm of size (600mm X 1200mm), in floors etc. Set jointed and pointed with Dr fixit Epoxy Tile Grout or equivalent fosroc to match the colour of tiles using 3mm thick PVC pipe spacers complete over and including 15mm thick screed bed screed bed in cement mortar (1:4) complete all as specified and as directed.

All as per item No 75 above but as skirting over and including 10mm thick rendering in CM 1:3.

M&L for 16-18mm thick granite ‘Jade black’ table rubbed and polished in Step, Jambs, Pillar, Window Cill, Cooking Platform in single piece. In cooking platform additional 75mm width of same granite patti stick with araldite or equivalent adhensive full moulding of edges to match the Coln our of granite, fixed with 15mm thick cement mortar in 1:4 complete all as specified and directed Note :- (a) Additonal 75mm width patti shall be measured separately. (b) Minimum rate of granite should not be less tan 150 Per Sqft including GST

M & L for 16-18 mm thick Machine cut kota stone single piece stone slab for riser, treads, landings over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15mm thick screed bed in CM 1:4 and rounding of edges, rubbing and polishing complete all as specified and directed.

M&L for 15 mm thick Full body vitrified tiles of size 800 x 2400 mm of approved shade in floor set jointed and painted with Dr Fixit Epoxy Tile Grout or equivalent fosroc to match the Colour of tiles complete over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for 15 mm thick Full body vitrified tiles of in single piece of approved shade including 15mm thick screed bed in CM 1: 4 as in treads/risers of steps in one piece including cutting, jointing, or step grooveing if required and full moulding complete all as specited and directed. Note: Step grooving shall be factory made and factory moulded

Taking up or down 15 mm dia GI tubing and connections complete all as specified.

Taking up or down 20 mm dia GI tubing and connections including cleaning for re-fixing, complete all as specified.

Supplying and laying of CPVC 20mm OD pipes SDR 11 & Plain/brass CPVC SDR 11 fittings & fixtures on walls/ceiling or laying in floors complete all as specified complete with fitting as required.

Supplying and laying of CPVC 25 mm OD pipes SDR 11 & Plain/brass CPVC SDR 11 fittings & fixtures on walls/ceiling or laying in floors complete all as specified complete with fitting as required.

S&F in Soft closing ball bearing telescopic channel of size 22 inch long fixed with screws in cupboards incl all fittings complete all as spd and directed by Engr in charge.Note : Runner/ Channel should be SS 304 grade and load capacity should not be less than 45 kgs Makes : Hettich, Godrej, Ozone

S&F Modular Cabinet Kitchen accessories of Stainless Steel grade-304,6mm size rod thickness including :- (i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket, (iv) Cup & saucer basket, (v) Glass basket, (vi) Plate basket, (vii) Premium magic corner (viii) Oil Pull out Tray ( Triple basket layer) , (ix) Dust bin, (x) Cleaning kit rack of size as per site requirement all spd and directed by Engr in charge

S & F 50 mm dia Galvanised Iron steel tubing, medium grade as in spout in short length, complete all as specified.

Dismantling of cast iron pipe of any dia (soil/waste/vent) with fittings etc fixed to walls,ceiling, on floors & from trenches if required including taking out any type of joints complete all as specified.

S & F 75 mm dia (bore of pipe) cast iron (sand cast) soil, waste, Vent hubless pipe as per IS-15905 : 2011 in any length with or without ears with cement joint fixed to walls, complete all as specified.

S & F 100 mm dia (bore of pipe) cast iron (sand cast) soil, waste, Vent hubless pipe as per IS-15905 : 2011 in any length with or without ears with cement joint fixed to walls, complete all as specified.

S&F 110mm dia (bore of pipe) cast iron hubless bends as per IS-15905 : 2011 (any radius), diminishing pieces or tapers (larger bore measured) jointed with stainless steel shielded SS-304 coupling double screw system with EPDM Rubber, complete all as specified.

S&F 75mm dia (bore of pipe) cast iron hubless bends as per IS-15905 : 2011 (any radius), diminishing pieces or tapers (larger bore measured) jointed with stainless steel shielded SS-304 coupling double screw system with EPDM Rubber, complete all as specified.

S&F 110mm dia (bore of pipe) cast iron hubless tee as per IS-15905:2011 (any radius), diminishing pieces or tapers (larger bore measured) jointed with stainless steel shielded SS-304 coupling double screw system with EPDM Rubber, complete all as specified.

S&F 75mm dia (bore of pipe) cast iron hubless tee as per IS-15905:2011 door with ovel access (any radius), diminishing pieces or tapers (larger bore measured) jointed with stainless steel shielded SS-304 coupling double screw system with EPDM Rubber, complete all as specified.

All as per item 92 above but fitted with hubless oval access door as per IS-15905 : 2011 for 110mm dia (bore of pipe).

All as per item 93 above but fitted with hubless oval access door as per IS-15905 : 2011 for 75 mm dia (bore of pipe)

S & F 75mm dia (bore of pipe) hubless cast iron branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door jointed with stainless steel shielded SS-304 coupling double screw system with EPDM Rubber, complete all as specified.

S & F 100mm dia (bore of pipe) hubless cast iron branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door jointed with stainless steel shielded SS-304 coupling double screw system with EPDM Rubber, complete all as specified.

S&F repair 75mm dia of outlet cast iron floor trap fixed with stainless steel shielded (SS-304) coupling double screw system with EPDM rubber to waste pipe fixed in cement concrete type B1 (1:2:3) complete all as specified and directed

S&F in repair Salt Glazed Stone Ware (SGSW) gully traps square or round mouthed type size 150x150mm including excavation/earth work, bed concrete, surrounding concrete and CI grating, complete all as specified.

S&F in repair vitreous pedestal pattern WC with ‘S’ trap fixed in position with necessary cement work complete all as specified and directed”. Makes : Jaquar : CNS-WHT-551SSPP, Hindware : 20079, Cera : S1053104S as approved by GE.

S&F in repair PVC valve less symphonic action type flushing cistern low level 10 ltr capacity (ISI marked) white with inlet ball valve float and handle including brackets complete all as specified and directed”. Makes : Jaquar : WHT-184 ANL, Hindware : 516366, Cera : B1020106 as approved by GE.

BLANK

S&F mortice lock of size 100mm with Brass fancy type and vertical type 4 levers with key in triplicate complete all as specified and directed.

S&F sinks made of stainless steel 1mm thick kitchen with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm all as specified and directed.

S & F in repair Brass CP health faucet hand shower type with 8mm dia 1.2 Meter long Flexible Tube and Wall Hook screwed for iron pipe fancy type long body all as specified and directed. Makes: Jaquar Cat No : ALD 573, Cera Cat No : F8030107AB, Hindware : F160023 & Kohler Cat No K-98100IN-CP as approved by GE.

Supply & fix in repair PVC connection pipe of 15mm x 600mm long with 2 Nos brass check nuts with washers, complete all as specified.

Supply & fix in repair CP connection pipe of 15mm x 600mm long with 2 Nos brass check nuts with washers, complete all as specified.

S&F in repairs vitreous chinaware coloured wall hung wash hand basin with full pedestal of size 550mm x 400mm complete including , CP Brass Waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed by Engr in charge.

S&F in repair vitreous china squatting pan of orissa pattern long pan size 580 x 440 mm white with "p"or "S" trap front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified.

S & F in repairs 10 ltrs PVC (White) valve less syphonic action type, flushing cistern low level with inlet ball valve float, handle, fixing with gitties embeded in wall with drilling machine etc complete all as specified.

S&F fancy type brass chromium plated toilet paper holder, complete all as specified. Makes : Cera Cat No: F5004110, Jaquar Cat No CPA-CHR-1153, Hindware Cat No. F-880003CP, Kohler Cat No K-5633IN-CP as approved by GE.

S&F in repair fancy type brass chromium plated soap dish, complete all as specified. Makes: Jaquar Cat No: ACN-CHR-1131N, Cera Cat No: F5007106, Hindware : 880011GRT as approved by GE.

S&F in repair SS cockroach trap with jali 125mm dia, complete all as specified.

S&F in repair stainless steel peg set of 6 peg, 45 centimeter long, complete all as specified.

S&F in repair fancy type 15mm dia brass chromium plated quarter turn basin mixer with braided hose for mixing hot and cold water screwed down for iron pipe and fixed to WHB complete all as specified. Makes : Jaquar Cat No: FLR-CHR-5167NB, Cera Cat No: F-2008461, Hindware : F570014 & Kohler Cat No K-29928IN-4ND-CP as approved by GE.

S&F in repair 15mm dia chromium plated quarter turn wall mixer hot & cold L bend 3 in 1 pattern fixing and connection to pipes, complete all as specified and directed. Make Jaquar FLR5281N, CERA F2008401, Hindware F570022 as approved by GE.

S&F in repair fancy type 15mm dia brass chromium plated quarter turn fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as directed. Make Jaquar FLR5309N ,CERA F1003501,Hindware F570027

S&F in repair fancy type chromium plated quarter turn brass angle valve type suitable for 15mm bore pipe complete all as specified Make: Jaquar FLR 15053PM, CERA F1001201, Hindware F570043”

S & F in repair Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union all as specified. Make : Cera Cat No F-7010609AB & F-7040207, Jaquar Cat No OHS-CHR-1663 & SHA-CHR-479L600, Hindware Cat No F-160219CP & F-160024CP, Kohler Cat No K-23657IN-CP & K-16346-IN-CP as approved by GE.

S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP brackrt gaurd and railling 60 cm long complete all as specified.

S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified .

S&F in repair fancy type glass corner 250mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified .

S&Fin repair fancy type stainless steel towel rack size 600mm X 300mm including apair of brass bracket Make : Cera Cat No F-5003101, Jaquar Cat No CPA-CHR-1181FH, Hindware Cat No F-580008CP, Kohler Cat No K-17529T-CP as approved by GE.

S&F stainless steel of AE - SI 316 grade tubular towel ring including apair of CP brass bracket complete all as specified .

S&F in repairs bib tap with crutch or butterfly handle, quarter turn screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium plated long body with flange complete all as specified Makes : Jaquar Cat No: FLRCHR-5047N, Cera Cat No : F-2008152, Hindware : F460003 & Kohler Cat No K-16093IN-4-CP as approved by GE.

S&F in repair Brass CP bib tap fancy type with flange 15mm dia screwed for iron pipe or for brass ferrule complete all as specified.

S&F in repair rectangular stainless steel sink with drainage board of 1mm thick sheet for kitchen with plug, washers, waste pipe including connecting union overall size minimum of 910mm x 450mm with bowl size of minimum of 410mmx 330mm x 160mm including taking out existing sink with waste fittings complete al as specified and directed

S&F in repairs Stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plat rack, complete all as specified and directed.

S&F in repair 1000 ltr capacity rotational moulded polyethylene white colour water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position with 20mm Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule Minimum wt 20mm-210grm and s&f in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed incl Dismantling of PVC water tanks of exc 500 litres and n.exc 1000 litres capacity of any condition or type incl complete all as specified and directed.

S&F in repairs of 25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F for steel windows / ventilators fabricated from roll formed sections made of galvanized steel colour coated powder coated (Base steel as per Sqm IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM with total coated thickness of 0.60mm. The coated section shall be with primer coated of primer of -7 microns thick, finish painted with a polyster paint of 12.16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure plyster powder upto 50-60microns thick with the following specifications (a) Main frame 72mm x 55mmx0.58mm (b) Mullion 72mmx50mm x0.58mm(c) Glazed/guazed shutter frame 47mmx20.20mmx0.58mm (d) Glass beads size 12mmx12mmx0.58mm Accessories. Each shutter shall be provided the following fittins (a) Stainless steel pipe of hinges 01 set (b) Alumminium powder coated handle-04 Nos. Glass panes Glazed shutter and fixed glass provided with glass of 5.00mm thick float glass. WIRE MESH -Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperature 1.40mm. Grills window shall be provided with grill made of 10mm square MS bars welded to 12mmx6mm thick MS plate. Distance between bars should not be more than 12cm c/c. Total grill unit shall be enamel painted and fixed to window frame with screw. Note: The glazed/Guaged shutter includingguard bars shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof and guard bars shall be made. Area of shutter shall be the area of opening. The rate quoted by the contractor is deemed to inclusive of all aspects as specified in Drg No- CEDZ/TD/289 sheet 1 R/2 and 2R/2.

Dismantling of floor of size not exceeding 4.00 Sqm mtr for EWC water closet and removing out the cinder/concrete from sunken protion, , grinding any sharp edges etc all as specified and directed with following: (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (d) M&L for providing 25 mm dia GI medium grade pipe spout projecting at least 150 mm beyond outer face of wall. (e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion is n.exc 4.00 Sqm each. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. (h) 72 hrs Ponding test shall be carried out for sunken treatment before payment.

Dismantling of floor of size not exceeding 1.50 Sqm mtr for EWC water closet and removing out the cinder/concrete from sunken protion, , grinding any sharp edges etc all as specified and directed with following: (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (d) M&L for providing 25 mm dia GI medium grade pipe spout projecting at least 150 mm beyond outer face of wall. (e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion is n.exc 1.50 Sqm each. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. (h) 72 hrs Ponding test shall be carried out for sunken treatment before payment.

M&L for 16 to 18mm thick granite stone of size 3' x 2' fixed on wall over 15mm thick screed bed in cm (1:4) and ingraved Bldg Nos and border over the stone for building insignia (letter size 3" to 2") complete all as specified and directed.

M&L for 10mm thick Glazed coloured tiles of size 200mm x 300mm fixed on wall over 10mm thick in cm (1:4) and ingraved Quarter Nos and border over the stone for building insignia (letter size ht 100mm and 50 mm width) for numbering Qtrs complete all as specified and directed.

Cutting shrubs wild growth, plants not exc 30 cm girth grown on permanet structures and removing same growth right from roots and stopping the recurrence by injecting herbicide Glyphosphate 4+ solution (04 % concentrate) into plant root to eliminate further growth. Application shall be as per manufactureres intructions. The disturbed area shall be repaired with PCC (1:2:4) Type B0 mix and surface finished even and smooth in cm 1:4 incl applying two coats of matching finish i.e. Exterior acrylic emulsion paint of same shade & finish. Likely minimum number of shrub/plants in each Building is not less than 50 nos . Work in high rise building upto six storiey height complete all as specified and directed at site

Dismantling of brick tiles or terracing tiles single layer on roof and removing the rubbish outside complex (MOD land),incl removal of vagitation if any complete all as specified.

Demolition of mud in roof, any thickness, including mud plastering and mud phuska under brick tiles at any situation and height, complete all as specified.

Roughening surfaces of old concretefloor by picking, sweeping clean andwashing down with water to removedust, etc

M &L for Brushing neat cement slurry with 3 Kg of cement per square metre complete all as specified and directed .

M&L for cement concrete 1:2:4 type B1 (using 12.5mm graded stone aggregate) on roof padding surface finished even and smooth without using extra cement complete all as spd & directed.

M&L for rendering 10mm thick on top of roof concrete in cement mortar 1:4 with water proofing compound at the rate of 3% by weight of cement to have a smooth surface for laying of water proofing membrane. Note: Water proofing compound will be measured and paid seprately.

M&L for APP based polymeric membrane with granular finish to receive tile, minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints

S & F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 9 to 10 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner complete all as specified.

M & L Cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof kerbs or mud stops etc including weathering slightly rounded or chamfered edges, finished even and smooth without using extra cement complete all as specified.

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M & L for Post Construction anti termiteTreatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same.

M & L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor sall as specified and directed.

M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. Supply & applying of rust removing chemical to remove rust from existing reinforcements. (The Engr-in-charge may order sand blasting if rust is visible) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for parapet railing, balconies, metre rooms shaft area any description complete as specified and directed upto six storey height..

S&F MS Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

M&L for Preparation of new steel and iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of redoxide primer, complete all as specified.

M&L for Preparation of old painted surfaces of steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint, complete all as specified.

S&F Steel work in tubular section for handgrip in balcony railing and roof terrace including painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication conforming to IS 1161-1979 grade St-240 complete.

S&F in MS Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe -290 Gde E-165 (Brackets over 10 kg each to be measured under ‘Structural Steel')

M&L for chipping out spilled and loose concrete cover and derusting steel reinforcement of concrete column, beam, slab, chajjas, parapets and the like as directed up to 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforcement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part of sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guiniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out up to 10 metre height) complete as directed at site Note :- (a) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guiniting is done with polycrete admixture @ 2% by weight of cement all as per manufacturers instructions (polycrete admixture shall be procured from chemical adhesive Pvt Ltd Co or their authorised dealer). (c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account.

Taking down existing steel rolling shutter incl hood cover pull & push type not exc 12 Sqm area of clear opening and cleaning the sides of shutters suspensions shafts,anti-guide channels and greasing all the moving parts of rolling shutters and straightening rolling shafts and replacement of bolts and nuts as required for smooth functioning of shutters and refixing the same incl hood cover complete all as specified and as directed.

S& F in repairs mild steel lock plate & handles made of of Flat iron 35 x 5 mm incl welding and painting with two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

S & F in repairs mild steel helical wire springs (confirming) as to IS-6248-1970) for shutters not exc 9 Sqm of approved make complete all as specified.

S & F in repairs roller ball bearing (ISI marked) for 32/40 mm dia pipe shaft complete all as specified and as directed by Engineer-in-charge.

S&F in repairs if interlocking lath section formed from rolled MS strip 1,2mm thick for rolling shutters above 3.5m width complete all as specified and as directed.

S & F in repair of steel rolling shutters without ball bearing, as specified incl top cover anchoring rod hasp & staple and one shop coat of primer before erected in position as directed complete manual type thickness of lath 1.25mm.

S&F Prefabricated Factory made FRP Chajja 4mm thick of Fibre ways brand or equivalent in required size, colour and design made by Resin Transfer Moulding (RTM) machine Technology, resulting in void free compact laminate in single piece, having smooth gradual slope curvature of easy drainage of water and duly reinforced by 2nos vertically and 1 nos horizontally 50 x2 mm thick MS flat with 12mm in built hole for grouting on existing wall along with the 50mm flanges duly inserted and sealed in the wall min width not less than 450 mm complete in one single piece casted monolithically incl all necessary fittings.

Cutting holes in brick wall built in cement mortar for inserting hold fasts, depth of embedded postion of hold fast /lugs measured from the face the jambs into the wall exc half brick but n.exc one brick thick and making good the dismantaled portion in cement mortar 1:3 or in cement concrete 1:2:4 type B-1, using 20mm graded stone agg complete all as specified upto six storey height.

S & F 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl Dismantling of PVC water tanks of exc 250 litres and n.exc 500 litres capacity of any condition or type complete all as specified and directed.

S&F 20 mm Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed. Minimum wt 15 mm -142grm , 20mm-210grm ,25mm -455grm,40mm-690grm complete all as specified and directed.

S&F of 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed complete to walls, ceilings or in floors with suitable clamps/bracket to maintain the gap between wall & pipe and fixing properly including taking down old PVC/CI pipes and necessary cutting through RCC roof and brick work etc (above six storey height) and making good all as specified.

S&F of 110 mm dia PVC (SWR) bends any radius with solvent joints, complete all as specified.

S&F powder coated aluminium Door seal not less than 1.00 mtr long with fine fibres suitable for fixing in doors.

Removing building materials etc.to a distance of 5.00km beyond the land included in the rates, including loading, unloading and stacking at the destination.

S&F 50mm dia wooden magnetic door stopper catcher fixed with screw in rear side of door to arrest closing.

M&L for precast cement concrete 1:2:4 type B-0 (using 12.5mm stone graded agg) as in louvers and jallies 25mm thick designed as fort pattern (measured solid) including all moulding but exceeding frame and set in CM1:4 all as per sample shown and directed by engineer-in -charge.

M&L for preparation of newly plastered surfaces of walls and providing and applying waterproof cement base putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified as directed.

M&L for preparation of old decorated plastered surfaces of walls, complete removal of existing treatment by rubbing , brooming down, washing with water etc and providing and applying waterproof cement base putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified as directed. Note for Item No 177 & 178 : (a) Memorandum of Understanding (MoU) : All exterior emulsion weather coat shall be got executed through authorized applicators of manufacturers. The contractor shall submit MoU on non judicial stamp paper of Rs 100 with any manufacturers of Exterior paints listed at Particular Specifications from which he proposes to carry out the work of these items in BOQ. The MoU shall cover guarantee and defects rectification during the guarantee period. Such applicator shall have valied authorization letter from the manufacturers issued not older than 30 days from the bid submitted to GE immediately after placing of Work Order who will vet the agreement. (b) Periodical visit of the site shall be carried out by the manufacturer of the exterior emulsion weather coat to ascertain the quality of work. The contractor shall obtain a performance certificate to this effect from the manufacturer and submit to GE, before issue of completion. 2% amount of work done of external painting will be retained as guarantee for 5 years. (c) Scope of work contains upto G+1 storey. Mechanical scrappers & mechanical sprayers will be used for finishes by using steel props or scaffolding etc.

S&F factory made uPVC white colour fixed glazed window/ventilator made of ( small series) frame 47 x 50mm mullion 47 x 68mm both having wall thickness of 1.9 + 0.20mm and single glazing bead of appropriate dimension ( Area upto 0.75 sqmtr) comprising of uPVC multichambered frame and mullion (wherevr required) extruded profile duly reinforced with 1.60 +0.20mm thick galvanised mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropraiate dimension, EPDM gasket, G.I. fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless screw etc.Profile of frame shall be miterd cut and fusion welded at all corners, mullion (if reqd) shall be also fusion welded including 5mm thick toughened glass drilling holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of reqd size and approval quality, all complete as per approved drg and direction of Engr in charge. Note: For uPVC frame, sash and mullion extruded profiles ,minus 5% tolerance in dimension i.e depth and width of profile dimension in higher side shall be acceptable but no extra payment on this account shall be made

S&F factory made uPVC white colour three track three panels sliding window with flyproof S.S. wiremesh ( Two nos. glazed & one no. wiremesh panels ) upto 1.50m ht made of big series frame 116 x 45mm & sash 46 x 62mm both having wall thickness of 2.3 + 0.20mm and single glazing bead/ double glazing beading of appropriate dimension ( Area of window upto 2.0 sqmtr) comprising of uPVC multichambered frame and mullion (wherevr required) extruded profile duly reinforced with 1.60 +0.20mm thick galvanised mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropraiate dimension, EPDM gasket, G.I. fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless screw etc.Profile of frame & sash shall be miterd cut and fusion welded at all corners, mullion (if reqd) shall be also fusion welded including 5mm thick toughened glass and SS wire mesh fixed and drilling holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of reqd size and approval quality, all complete as per approved drg and direction of Engr in charge. Note: For uPVC frame, sash and mullion extruded profiles ,minus 5% tolerance in dimension i.e depth and width of profile dimension in higher side shall be acceptable but no extra payment on this account shall be made

BLANK

ROAD, PATH & CULVERT

Surface dressing averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed by Enginer-in-Charge

M&L cement concrete 1:4:8 type D- 2 (40mm graded stone aggregate) as in sub base, hard standing of 75 mm thick, complete all as specified.

M&L for Sand filling (sand cushioning) under floors or in foundations including watering and consolidations complete all as specified and directed.

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors all as directed.

S&F Machine pressed precast concrete interlocking coloured paver block of approved pattern shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with greay cement and pigment complete all as directed.

M&L for Providing cement concrete type B1 1;2;4 (20mm graded stone aggregate) as in kerbs or mud stops, rounded or chamfered on edges.

Removing excavated materials to a distance not exc 50 Mtr and depositing where directed.

SEWAGE DISPOSAL

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified.

Returning filling in, incl spreading levelling watering and well ramming in layers n exc 25cm (after the pipes have been laid and tested) in soft/loose soil complete all as specified.

Removing excavated materials to a distance n.exc 50 m and depositing where directed.

M&L PCC 1 : 4 : 8 type D2 using 40mm graded stone aggregates as in foundation of manholes, posts etc complete all as specified.

M&L for PCC 1 : 2 : 4 type B2 using 20mm graded aggregates as in surfaces channels and drains complete all as specified.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/stoped ends etc complete all as specified.

S&F Cast iron soil, waste and vent pipes in any length with or without ars, with cement joints, laid in trenches or in floors complete all as specified.

M&L for Brick work sub class ‘B’ bricks state or curved on plan built in cement mortar 1:4 using old size bricks complete all as specified and directed.

M&L PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregates in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed.

M&L for precast factory made manhole cover, area of each cover n.exc 0.60 Sqm, 75 mm thick with SFRC concreting including grove and hook arrangement for lifting and placing in position and sides covered by MS sheet complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 100mm internal dia pipe, complete all as specified.

M&L for rendering 15mm thick on top of roof concrete in cement mortar 1:4 with water proofing compound at the rate of 3% by weight of cement to have a smooth surface for laying of water proofing membrane. Note: Water proofing compound will be measured and paid seprately.

Supplied only integral water proofing for water proofing purposes

Demolition and breaking up drain pipes (glazed stone ware, AC or reinforced concrete),150 mm dia pipe of any description and in any position set and jointed in cement mortar complete all as specified and directed by Engr-in-Charge

AREA DRAINAGE

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified.

M&L PCC 1 : 4 : 8 type D2 using 40mm graded stone aggregates as in foundation of manholes, posts etc complete all as specified.

M&L for Cement concrete 1:3:6 type B-2 as in surface channals or drains all as specified and directed.

Removing excavated materials to a distance n.exc 50 m and depositing where directed.

Returning filling in, incl spreading levelling watering and well ramming in layers n exc 25cm (after the pipes have been laid and tested) in soft/loose soil complete all as specified.

M&L for brick work with sub class 'B' brick straight or curved on plan exc 6 metre mean radius with old size bricks, built in cement mortar 1:4, complete all as specified.

M&L for rendering 15mm thick in cement mortar (1:4) on concrete/ fair surfaces of block masonry, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

S&F DWCPE(SN8) 150mm dia (Internal Dia) pipes,snap fit coupler and rubber ring incl testing and laid and properly jointed laid in trenches to a level on concrete bed complete all as specified.

FENCING/GATE & COMPOUND WALL

Excavating in post holes (or similar holes) each not exceeding 0.50 cu m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/loose soil complete all as specified.

S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

M&L for Cement concrete 1:3:6 type C2 using 40mm aggragate in foundations, filling and mass-concrete

Supply only Chain link MS galvanisd fencing, any size or type

Fixing only Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire

S&F Mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged, and jagged or lewised, n exc 15cm long

S&F Mild steel in flat, round bars, in available lengths Fe 410 W (Gde E-250 quality A)

S&F in repairs pre painted galvalume aluminum ZINC coating GI base corrugated steel 0.5mm thick of any Colour having tensile strength of 550 MPA as in roof covering/cladding to wall fixed with self tapping screw with minimum 150mm end lap and one corrugation side lap including dismantling the existing sheets complete all as specified and directed.

S&F stainless steel grill(Grade-304) using 10mm thick square bars (100mm C/C) of weight not less than 0.62 kg/Rm including necessary frame and accessories for window and ventilator grill complete all as specified and directed.

M &L for Brushing neat cement slurry with 3 Kg of cement per square metre on chajja complete all as specified and directed.

M&L for rendering 15mm thick on top of roof chajja concrete in cement mortar 1:4 mixed with water proofing compound @ of 3% by weight of cement to have a smooth surface for laying of water proofing including taking down complete all as specified

M & L for applying Dampproof coating, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on top of roof surface in multiple coats @2 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and other coats needs to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. When the 2nd coat is wet, the EPDM tape (at corners and edges)shall be inserted between second and third coat to secure corners & edges, let the material ooze out from the tapes corner. Same treatment of Dampproof shall be continued to the parapet walls to better envelope the whole area. The coating shall be terminated carefully to the other side of the parapet wall.

Description of Work / Item(s)

Amount

Taking down carefully copper/aluminium point wiring (light/fan/ socket/power) complete from the wall by cutting/ chasing including fittings and fixtures such as switches, ceiling roses, pendants holder, regulators,sockets,light fittings etc for credit and making good the disturbed surfaces of wall, floor etc complete all as specified and directed.

Taking down carefully sub main wiring of any description.

Disconnecting electric & water supply connections, nuts-bolts & taking down Geyser different capacity and shifting to MES store yard.

Disconnecting elect connection and taking down of ceiling fan/Exhaust fan of any make and any height, dismantling blade and removing fan alongwith blade for depositing in MES store yard complete all as specified.

Taking down defective DB SPN with MCBs of any capacity and make including wooden board etc complete all as specified and directed.

M & L for Point wiring (concealed) complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded copper conductor drawn through in and including non metallic medium grade rigid PVC conduit, ISI marked not less than 20 mm dia including all accessories concealed in wall by cutting chases and including provision of 1.5 sqmm PVC insulated unsheathed copper cable FRLS as earth continuty conductor including fabricated branded modular metal flush box duly make embossed, concealed in walls and making the adjacent surfaces smooth through POP work & painting as per site requirement and with suitable modular inner and outer plate for housing switches , socket out let and fan regulators etc, complete all as specified and as directed for the followings:- One light /Ceiling fan/exhaust fan point controlled by one, one way switch .

All as per item No 6 above but for One bell point controlled by one bell push.

All as per item No 6 above but for One light point controlled by two Nos two way switches

All as per item No 6 above but for One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent but not below the switch board of light point.

All as per item No 6 above but for One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent but not below the switch board of light point.

All as per item No.6 herein before but with 4 Sqmm cable for one 3 pin 15 Amp switch socket outlet and using 4 sqmm PVC single core copper conductor cable multistranded as earth wire complete all as specified and directed. Note for Item 6 & 7 : (i) In case the wiring is encountered with any beam/column, then the wiring will run on PVC casing&caping/Existing conduit to avoid any damage to the RCC portion. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling fan point wiring, in this specified portion wires shall run through the surface new conduit shall be provided as mentioned in note (i) above. (iii) Proper colour code will be used for wiring as per the electrical rule and as directed by EIC.

M&L switch Modular type 6 Amps SP 230V AC complete all as specified and directed.

M&L switch modular type 6 amp two way complete all as specified and directed.

M&L Modular socket outlet 5 pin 6 Amp socket 2 module complete all as specified and directed.

M&L switch bell push Modular type 6 Amps 1W-1 module, 230V AC complete all as specified and directed.

M&L switch Modular type 16 Amps SP 230V AC complete all as specified and directed.

M&L Modular socket outlet 5 pin 6/16 Amp universal socket 2 module complete all as specified and directed.

S&F ceiling rose, PVC / Polycarbonate, isolated body with three terminals.

M&L bell electric operated (ding dong) 230 volt, SP Electric grade in polycarbonate material having audible range of min 50 mtr for 3 sec duration all as specified and directed.

S&F of modular AC Box consisting of 20 Amp multipower socket including MCB SP of capacity 25 Amp mini MCB, ‘C’ curve, single phase 240 V, AC including modular box, frame, cover plate including plug top with indicator complete all as specified and directed .

Supply in replacement and fix Slim LED T-5 batten luminaire surface mounted with aluminium extruded housing & polycarbonate diffuser, 4 feet system wattage of 20 Watts with lifetime of 25000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 20%, colour temperature - 6500K, surge protection 4 KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 Degree C, system efficency at luminaire level >110 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed by Engr-in-charge. Note- All the above mentioned specs will be verified through LM 79 and LM 80 report of NABL accredited lab before supply of LED fixtures.

S&F in replacement of Slim LED T-5 batten luminaire surface mounted with aluminium extruded housing & polycarbonate diffuser 2 feet system wattage of 10 watts and not less than 1000 lm with life time of 25000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.95, THD < 10%, color temperature > 6500 K , surge protection 4 KV in CM IP- 20 protected meets LED IS specifications, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, system efficiancy at luminarie level ≥100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed.

S&F in replacement of decorative type wall mounted luminaire (comet type) with unbreakable poly carbonate materials with 1x14 watt LED bulb B22 Base having lumen efficiency 100lm/w, 6500K complete all as directed.

S&F in replacement of LED 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 100 lm/W with a life class of25000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<20%, CRI>80, Color Temperature-6500K, Surge protection of 2.5 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed complete all as specified and directed by Engr-in-charge. Note :- All the above mentioned specs will be verified through LM 79 and LM 80 report of NABL accredited lab before supply of LED fixtures

S & F in replacement of surface ceiling mounted, round LED down light fitting 12 watts with die cast aluminium housing and system wattage of 12W, system efficacy at luminary level ≥ 100 Lumens/watt,25000 burning hours, 6500K color temperature with CRI >80, Power Factor > 0.95, Driver should meet IEC compliant for safety with multi stage high Isolate CC-CV operated driver with voltage variation range - 150 to 270 Volts AC, and surge protection of 2.5 KV, and including connecting up with PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed.

M&L for angle Lamp holder with metalic ring, pvc/ polycarbonate type back plate with LED bulb 09 watt, 900 lumens out put, 6500K suitable for B-22 base all as per directed

S&F 36 W High efficient LED Street light fitting with pressure die cast Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover. System level efficacy of the Luminarie should more than 100lm/W. The color temperature is around 6500 K with a color rendering index of 70. The luminaire is IP:66 protected. It has an electronic driver complaint to IEC safety standards with a power factor>.0.95, voltage variation range 120-270V, THD<20%, High and low voltage protection along with a surge protection of 5 KV internal including provision of sutable dia GI light grade pipe1.2 meter length bend to shape and necessary clamps etc for fixing the light fittings on wall fixed complete as specified and directed.

S & F water heater storage type (Geyser) vertical type ABS body maximum operating pressure 8 bar with safety valve nickle coated element with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection, having adjustable knob for temperature control and inner tank should be glass line coated complete all as specified of capacity 25 ltr having heating element 2 KW and not less than 5 star rating.

Re-fixing carefully existing serviceable Geyser of any size along with all fittings & fixture and make good its position .

Supply and fixing ceiling fans complete three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220cum/min, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible copper cable pvc insulated of suitable length, down rods, Remote of Ceiling fan and accessories complete.

Supply and fixing of wall mounted fan 400 mm sweep, aerodynamic designed, air delivery ≥ 70 CMM, thermal over load protected motor, 3 blade white colour, 230 volts, 50 Hz, 1300 RPM with 90 degree oscillation and having speed & oscillation control by two pull cords system complete all as specified

Supply and fixing Ventilating Fan 250 mm sweep, 1250 RPM, non metallic resin body, single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of copper cable 3 core of size 0.5 sqmm and making necessary opening in brick wall/window as per site condition complete all as specified and as directed.

Supply and fixing heavy duty exhuast Fan 300 mm sweep, 1400 RPM, metallic body, single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of copper cable 3 core of size 0.5 sqmm and making necessary opening in brick wall/window as per site condition complete all as specified.

S&F MCB DB SPN 04 way, double door 240 V AC 50Hz, MCB SPN as incomer / out going complete. Note:-(i) MCB shall be measured & paid separately (ii) make of DBs & MCB should be same

S&F MCB DB SPN 12 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete Note:-(i) MCB shall be measured & paid separately (ii) make of DBs & MCB should be same

S&F MCB SPN 40 Amps 240 volts 10 KA 50 HZ 'B' curve complete.

S&F MCB SPN 16 Amps 240 volts 10 KA 50 HZ 'B' curve complete.

S&F MCB SP 6 - 32 Amps 240 volts 10 KA 50 HZ 'B' curve complete.

M&L for Sub main wiring complete with two runs of 4 Sqmm single core PVC insulated FRLS unsheathed cable 1100 volts grade, multistranded copper conductor cable with one run of 4 sqmm single core PVC insulated FRLS unsheathed cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 20 mm dia non metallic rigid PVC conduit and conduit accessories concealed in walls all as specified and as directed. Note:- (1) Two runs of cable, one run of earth continuity conductor and one run of PVC conduit shall be measured as unit length. (2) The damaged surfaces to be made good with plastering will be carried out by contractor and cost of the same deem to be included in the quoted rates. Nothing extra in this account will be admissible.

M&L for Sub main wiring complete with two runs of 6 Sqmm single core PVC insulated FRLS unsheathed cable 1100 volts grade, multistranded copper conductor cable with one run of 6 sqmm single core PVC insulated FRLS unsheathed cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 20 mm dia non metallic rigid PVC conduit and conduit accessories concealed in walls all as specified and as directed. Note:- (1) Two runs of cable, one run of earth continuity conductor and one run of PVC conduit shall be measured as unit length. (2) The damaged surfaces to be made good with plastering will be carried out by contractor and cost of the same deem to be included in the quoted rates. Nothing extra in this account will be admissible.

M&L for Sub main wiring complete with two runs of 10 Sqmm single core PVC insulated FRLS unsheathed cable 1100 volts grade, multistranded copper conductor cable with one run of 10 sqmm single core PVC insulated FRLS unsheathed cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm dia non metallic rigid PVC conduit and conduit accessories concealed in walls all as specified and as directed. Note:- (1) Two runs of cable, one run of earth continuity conductor and one run of PVC conduit shall be measured as unit length. (2) The damaged surfaces to be made good with plastering will be carried out by contractor and cost of the same deem to be included in the quoted rates. Nothing extra in this account will be admissible.

Dismantling and taking out old unserviceable Earthing and M&L earthing complete with GI electrode 600x 600 x 6mm, thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below normal ground level (with top edge of earth plate not less than 1.50 mtr below normal ground level connected to GI wire 4.0 mm as earthing lead by means of bolt nuts, check nuts, and washers of brass connected including gun metal or phosphorus bronze drilled and screwed all as specified including excavation and earth work and disposal of surplus soil incl 15 mm GI tubing light grade and necessary fitting for protection of GI wire incl laying of alternate layer of charcoal dust and common salt PPC (1:2:3) type C-1 (using 20mm graded stone aggregate) for earth pit with 40 x 40 x 6mm MS angle iron frame for cover 40 mm thick (1:2:4) type B20 using 12.5 mm graded stone aggregate reinforced with 8 mm dia round bar @ 75mm C/C both way with MS handle 20mm dia plastering 15mm thick CM (1:6) internally and upto 150mm below ground level externally PGL funnel with ground wire mesh 20mm dia GI pipe Medium grade for watering complete all as shown on electrical plate No 3 of SSR Part-1 2009 and connected in earth test incl testing completed all as specified and directed. Note:- Galvanised wire and protection light grade GI pipe upto 7.5 mtr shall be deemed to be in the rates.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recessed or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc of size 4.0 mm thick galvanised wire with duly fixed on suitable size complete

M&L for fixing of suitable size of fan hook/ clamp made mild steel 6 mm thick in round shape fixing in 40mm GI pipe, load carrying capacity not less than 6 kg and necessary accessories as per site requirement complete all as specified and directed.

S&F wall mounted angular Electric chimney of size 900mm and suction power not less than 1200Cum/Hr, Al casette with stainless steel outer layer ,touch control panel,3 speed motor with 250 watt with decorative smart cooker hood SS and glass ,energy efficent Led light with digital display , including ducting not less than 20 feet as per site required complete all as specified and as directed. Make – GLEN, LIVPURE, HINDWARE. Cat Part No.- GLEN-CH6061 BL BLDC AC. Cat Part No. – LIVPURE - ELICA FL 600 SLIM HAC Cat Part No. – HINDWARE - HOOD VENICE in HS SC FL LG 60.

Supply, laying in repairs of PVC under ground XLPE insulated heavy duty electric cables armoured with aluminium conductor, 1100 volts grade, cross sectional area 10 sqmm 2 core laying in trenches, fixed along wall, through GI pipe under floor complete all as specified.

Excavation in trenches n.exc 0.45 m wide and n.exc 0.60 m depth for laying of LT cables etc. and getting out in hard/dense soil soil soil complete all as specified

Returning filling in including spreading, levelling, watering and well ramming in layers n. exc. 25 cm complete all as specified and directed.

Removal of excavation material not exc 50 Meter and depositing where directed at a level not exc. 1.5 M above the starting point complete all as specified and directed.

M&L for dry river sand filling in trenches as cushioning to under ground cable provided with a layer of 8 cm deep before laying and 15 cm covering above the top edge of cable after laying complete all as specified and as directed by EIC. Note :- Punned thickness only shall be measured and paid.

Supplied & fixing GI tubing medium grade 40 mm dia with required fittings and fixed to wall/ceiling for hanging of ceiling fan complete all as specified and directed of following

Supplied & fixing GI tubing light grade 40 mm dia with required fittings laid along with poles/walls/Roads/Paths for incoming and outgoing of cable complete all as specified and directed of following

Supplying laying sub class ‘B’ bricks old size with axis of the bricks perpendicular to the axis of the cable as in cable protection complete all as specified and directed.

S&F Instant Hot Water Geyser 3 Ltrs capacity,3 KW with corrosion proof thermoplastic external body ,ISI approved with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection complete all as specifiedand directed by Engineer -in-charge.

M&L for TV Point wiring (concealed) complete with all accessories & provide for TV cable drawn through in and including non metallic medium grade rigid PVC Conduit, ISI marked not less than 20 mm dia for TV socket outlet on independent modular TV board etc all as specified and directed.

S&F delux TV socket outlet with 1 module on phenolic laminated sheet etc as required.

L G BUILDERS (BID ID -3138872)

M/S Chhavi Constructions Co (BID ID -3138970)

ASSOCIATED CONSTRUCTION CO. (BID ID -3139044)

M/s Innovative Coolings and Constructions (BID ID -3145857)

Global Enterprises (BID ID -3138822)

JYOTI ENTERPRISES (BID ID -3138452)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3133326)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3133326)

Adhunik Builders (BID ID -3146129)

M/S Chhavi Constructions Co (BID ID -3138970)

L G BUILDERS (BID ID -3138872)

JYOTI ENTERPRISES (BID ID -3138452)

Global Enterprises (BID ID -3138822)

M/s Innovative Coolings and Constructions (BID ID -3145857)