Construction of 50 Bedded Prefabricated field Hospital at Bokaro, Gumla, Jamtara, Khunti, Latehar and Garhwa District.

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. (a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

Providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. (a) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete

Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete. 100x70x4 mm (ordinary type)

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses

Providing & Applying weather proof sealant on outer joints of approved make confirming to IS & directed by Engineer-in charge.Sealant 25mmx10mm at joints

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Dark shade pigment using ordinary cement

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade,in wall tiles, skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm make Kajaria/ Restile/Johnson or equivqlent (Basic cost of tile - Rs.85/sft).Any difference in basic price and OHP at the time of approval shall be adjusted for the laid area.No extra shall be payable for forming any pattern in the flooring like border, cut tiles,etc.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joint treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab over 0.50 sqm

Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

CARRAGE OF MATERIALS

Sand 8 Km

Local Sand 3Km

Stone Chips 22 Km

Metal - 22km

Brick 1k+7p

Earth

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc:150 mm diameter

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia

Providino and fixinq Gun metal full way valvc of tpprovod quality, all (c) 25mm dia and weiqht not less than 500gms. Each

Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating.

Providing and fixing male ended 1Smm dia brass bib cock of lappror"d quality (Wt. not less than 350gms.) with extra socket all complete as per specification and direction of E/1.

Suppling, fitting and fixiilS40mm high-vitreous white glaz-dd earthen E.W.C. with 'p' trap of parry hindustan or any other approved l.S.S. make including supplying and fixing l5litres C.l. mosquito proof low down flushing cistern of approved make with complote fittings with C.l.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 1Smm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other LS.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and dlrection of E/|. E.W.C. with'S' trap 10lit. low level PVC clstem

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 :15mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 32 mm nominal outer dia Pipes

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour. weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT extension nipple for water thank pipe, fittings of approved quality and colour .20 mm nominal bore, weighing not less than 40 gms

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:20 mm nominal bore

Providing and fixing CP Brass 32mm size Bottle trap of approved quality & make and as per the direction of Engineer in charge.

Point wiring in PVC conduit with modular type switch. Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for circuit/submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.

2X1.5 sq.mm + 1X1.5 sq.mm earth wire

2X2.5 sq.mm + 1 X2.5 sq mm earth wire

2X4 sq.mm + 1X4 sq.mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire(for ups incomer and outgoing wiring)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.(ISI Make)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Modular type blanking plate: Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Modular boxes, bases & cover plate: Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required.

4 module

6 module

Supplying Modular type switch/socket: nd fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.

5/6 Amps switch

3 pin 5/6 Amp socket outlet

15/16 Amps switch

6pin 15/16 Amps (universal) socket outlet

Bell push

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

ITC Fluroscent fittings: Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door(for ups incomer and outgoing isolation)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator)

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

4 way (4 + 12), Double door

8 way (4 + 24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testingand commissioning etc. as required.

Single pole

6/32 AMPS TPN

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth,metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, onsurface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providingmasonry enclosure with cover plate having locking arrangement and watering pipe etc. withcharcoal/ coke and salt as required

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earthelectrode, including connection/ terminating with nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

LAYING OF LT CABLES Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 25/40x3mm MS flat clamp)

HT CABLE LAYING Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required Above 120 sq. mm and upto 400 sq. mm

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 200 mm dia (OD-200 mm & ID-175 mm nominal)

LT CABLE TERMINATION Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 300 sq. mm (70mm)

3½ X 185 sq. mm (50mm)

3½ X 150sq. mm (50mm)

3½ X 35 sq. mm (32mm)

4 X 25 sq. mm (28mm)

4 X 16 sq. mm (28mm)

4 X 10 sq. mm (25mm)

3 X 10sqmm(22mm)

HT CABLE TERMINATION Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required. 300 SQ MM

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 300 SQ MM

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray(Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as require

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width x 62.5 mm depth x 2 mm thickness

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and Drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 4 PAIR

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.1 or 2 Module (75mmX75mm)

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required(other areas & above ceiling)

Supplying, installation, testing & commissioning of manual call box of ABS type in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in A.B.S. box with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 ZONE

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 100mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing 6 amps to 32/63 amps rating, 240 volts, 10 kA, "C" curve, miniature circuit breaker suitable for.inductive load of following poles in the existing MCB DB complete with connections, esting and commissioning etc. as required. 40 amps, TPN

SITC of following ratings recess or surface mounted LED round or square shaped down light luminaire with pressure die cast housing for single phase supply voltage.Luminare shall be conform to IS:10322/PART 5/Section 2 or IEC 62722 with all necessary accessories as required. 2'x2' LED Panel ligbt

S.I.T.C of following rating surface mounted LED tube light fitting suitable for 230V 50H2, single phase supply etc. complete as required. 20/22W LED Tube light

SITC of following ratings recess or surface mounted LED round or square shaped down light luminaire with pressure die cast housing for single phase supply voltage.Luminare shall be conform to IS:10322/PART 5/Section 2 or IEC 62722 with all necessary accessories as required.2W LED Round Down ligbt

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to13:374,.2019 including wiring the down rods of standard length (upto 30cm) with l.Ssq.mm. FR PVC insulated, copper wire suitable for 230V 50H2, single phase supply etc. complete as required. 1200mm (48") BLDC 5star rating 32W Ceiling Fan

Supply of wall fan 400 mm sweep, 230V, 1Ph, plastic body and blades, pull cord for speed regulation, complete with all accessories as required.

Supply of 300 mm sweep, 1325 - 1380 rpm, metal blade & bird guard, Epoxy powder coated, exhaust fan complete with all required accessories including mounting accessories.

100kVA DIESEL GENERATOR WITH AMF PANEL (DG provided only for critical equipment loads, emergency lights, fire system and alternative air conditioners.) Supply & installation of Silent type D.G Set of capacity 100 KVA With AMF Panel IS/IEC-60034- 1 IS: 1460 IS: 13018

Supply of 20 KVA online UI€ three phase input and three phase output power system of input Voltage range 110V AC +/- 5% - 300V AC +/- 5%, Frequenry range 40Hz - 60Hz, Power Factor > 0.90 @ full load, and output Voltage range 200 V /208/220/230/240V AC, Voltage regulation +/-1%, Frequency range 50Hz +/- 0.25Hz or 60Hz +/- .30HZ Harmonic disbortion - < 2% THD (Linear load) : 4% THD (non-linear load) efficiency -88/83%

MS battery rack suitable for 15 to 20 UPS Battery installatio

12V, 65Ah sealed maintenance free (SMF) battery with 24 month replacement zuaranty. 15:1652:1991

Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date.

3½ X 185 sq. mm

3½ X 240 sq. mm

3½ X 150sq. mm

3½ X 35 sq. mm

4 X 25 sq. mm

4 X 16 sq. mm

4 X 10 sq. mm

total cost of 131 nos of schedule items of work

Supply and fixing of PUF panel Doors, windows, partitions, roof made up of GI powder coated 0.47mm thick sheet on both sides, with 50 mm thick class 'O' PUF of min.38kg/m3 density sandwiched in between. The GI sheet shall have 80 micron thick powder coating by hot dip galvanizing with zinc coating not less than 180gm/sqm on both sides of the panel. Scope includes bottom runner, inter connecting profiles, fixing arrangements, silicon sealant application and all other accessories required to complete the work as per site requirement. Colour: Powder coated, complete with all necessary hardware, accessories, fittings and fixtures, as per description in individual items, technical specifications, drawings and instructions of the Engineer-Incharge. including GI Frames.

Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10 Kgf/cm2- External work - Exposed on wall

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10 Kgf/cm2 - External work- Exposed on wall

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10Kgf/cm2 - External work - Exposed on wall

Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC soil, waste and vent pipe to IS : 13592 of SWR quality including all fittings, like : Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring / solvent cement by application of leak proof adhesive like FRP paste including cutting holes in walls and floors and making good.50mm dia <

:Providing and fixing C.P. brass shower with 3 Flow Ultra Slim Shower (8 Inch X 8 Inch) Stainless Steel 304 Grade + 18 Inch Shower Arm + Square Flange Complete Set.

Providing and fixing M.S. Fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or square tube during laying, including painting the exposed portion of loop, all as per standard design complete as required.

DOUBLE POLE STRCTURE Supply and Erection of Double pole structure using 10.5 mtr 200 x 100mm RS joist with required quantity of 100 x 50mm MS channel for mounting AB switch, DO fuses, Lightning arrestors,etc with Ms flats clamps,base plate, bolts nuts etc., including cutting, welding, aluminium painting all as per standard requirements of Electrical inspectorate, complete including supply and installation of following overhead line accessories as required.

11KV pin insulators

11KV Disc insulators

11KV, 400A, 3 phase gang operated , vertical single make/break type off load Air breake switches complete with all hardwares like insulators, fixing channels, operating rods, handle locking arrangements, bolts nuts and complete

9kv, 5kA lighting arrestor

11kV, 400A dropout fuse sets, complete with all hard ware like supporting insulators, fuse rods, bolts and nuts complete.

4 Nos.Pipe earth electrode for the DP structure & LA Earthing, 6 SWG Copper for Lightning arrestor earthing including all round fencing

160 kVA OUTDOOR UNITISED SUBSTATION WITH HT METERING Supplying, Installation, Testing and Commissioning of following capacity Cast Resin Dry Type, 160 KVA, 11/0.415 KV,350 MVA, 3 Phase, 50Hz, Dyn11 vector group, copper wound, outdoor Transformer having class H insulation with 11 KV, 630A, 26.2kA Load Break Switch Panel with CT,PT and provision for fixing HT TOD meter associated with winding temperature indicator/controller actuated by means of resistance temperature detector embedded in LV windings along with supporting channels at bottom with brought out neutral complete with automatic ON Load tap Changing Gear (with vacuum interrupters) for tap range + 5% to -15% in steps of 2.5% on H.V. side with HT cable chamber suitable for Heat shrinkable joint with XLPE cable (cable entry from Bottom) and LT connection chamber suitable for connecting Bus duct arrangement and equipped with other essential accessories including providing and fixing of neutral CT in brought out neutral for low set standby earth fault relay unit etc. as required. The transformer losses shall be within the limits prescribed as per ECBC 2009 norms or higher. % Impedance and Temp Rise of Winding and shall be as per IS: 11171

Supply and providing of one number HT TOD meter with test certificate obtained from T.M.R Dn. of Electricity Board (CTs,PTs also shall be tested and certificate obtained) This include the dismantling of CTs and PTs from the L.B.S.F.U getting it tested by Electricity Board and refixing them in the unit.

Supply,Installation & Commissioning of 200/5 A, 15VA, 5P10 cast resin moulded bar type CT for the Transformer neutral in metallic enclosure with gasketed openable screwed covers, including the supply of the enclosure-1 No.

Supply, fabrication and Erection of Exhaust piping up to Building Roof top,using 4" Class BMS Pipe including Painting including Supply, Fabrication and Erection of MS Angle Support for Exhaust Piping up to roof top.

Charges for Preparation of all drawings submitting and getting approval from Electrical Inspectorate, submitting of Completion certificates and arranging inspection, getting sanction and energisation certificates from Electrical Inspectorate ,CPWD& EB, obtaining power allocation & power connection etc. for commissioning of the whole installation in the premises including generator etc.

Contractor has to arrange load test at site or at factory without any additional cost or claim. Including First fill of lube oil and Engine safeties – LLOP, HWT, Initial filling of diesel for standard testing procedure up to 6 hours minimum and 12 hours maximum.

LT PANELS Supply, installation, Testing and Commissioning of dust, damp and vermin proof free floor /wall mounted, Indoor type factory built sheet steel enclosed compartmentalized cubicle panel board , suitable for operation on 415 ±10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of with CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, complete with Aluminium/copper bus bars as below, inter-connection with copper conductor wires / aluminium strips, neutral links, earth bus etc. including control wiring with 1.5sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor single core cable for voltage & current respectively, cable alleys, cable gland plates in two half, etc. necessary metering protections & indications and mounted with the following switch gears etc. complete as required. (Each MCCB will have variable current setting for over current, front extended lockable handle, pad lockable in off position, indication light for ON, shrouding on incomer side, termination shall be suitable for aluminium bus bars. . Current density of aluminium and copper busbars shall not be more than 0.80 A per sq.mm. and 1.2A per sq.mm respectively. MSB

Supply installation testing and commissioning of 250A,LT floor mounted type, dust and vermin proof, free standing cubical type construction, made out 16SWG CRCA sheet painted with approved colour after decrea sing pickling, phosphating etc consisting of the following:

(a) Incomer :

250A, 4P 35 KA MCCB with MCCB set at 213 A of specified make and having external 3xO/C, S/C & E/F setting facility. Terminal shrouds shall be provided at the incoming and outgoing terminals. The MCCB shall have AC shunt trip coil - 1 No.

(b) Bus bar: 250A Aluminium bus bar.

(c) Outgoings

1. 160A 4P 25kA Thermal magnetic type MCCB - 1 Nos

2. 200A 4P 25kA Thermal magnetic type MCCB - 1 Nos

3. 100A 4P 25kA Thermal magnetic type MCCB - 1 Nos

Meters :

All meters shall be of 96 mm square, panel mounting type and accuracy class 1.0 or better with finger-proof terminals.

1. Multi-Function Meter : CT operated, 3 x 240 V, 3 x -/5 A, 3-Phase 4 wire, Cl. - 0.5 meter to read voltage, current, p.f., power etc. - 1 Nos.

Indication Lamps :

LED type R, Y, B coloured indication lamps with 2 A HRC control fuses mounted on 32 A Bakelite fuse carrier & base - 3 set

Earthing :

Main earth bus : Copper flat of size - 25 x3 mm

Sub panel-SSB Supply installation testing and commissioning of 200A,LT floor mounted type, dust and vermin proof, free standing cubical type construction, made out 16SWG CRCA sheet painted with approved colour after decrea sing pickling, phosphating etc consisting of the following:

(a) Incomer :

200A, 4P Isolator - 1 No.

(b) Bus bar: 200A Aluminium bus bar.

(c) Outgoings

1. 63A 4P 25kA Thermal magnetic type MCCB - 6 Nos

Meters :

All meters shall be of 96 mm square, panel mounting type and accuracy class 1.0 or better with finger-proof terminals.

1. Multi-Function Meter : CT operated, 3 x 240 V, 3 x -/5 A, 3-Phase 4 wire, Cl. - 0.5 meter to read voltage, current, p.f., power etc. - 1 Nos.

Indication Lamps :

LED type R, Y, B coloured indication lamps with 2 A HRC control fuses mounted on 32 A Bakelite fuse carrier & base - 3 set

Earthing :

Main earth bus : Copper flat of size - 25 x3 mm

Capacitor Cubicle : The capacitor cubicles shall be provided on the rear side of the panel in properly segregated, well ventilated compartments having louvers and thermostat controlled ventilation fan on the top of the chamber. Each capacitor cubicle shall be suitable for mounting 25kVAr, 440 V heavy duty capacitors. Each capacitor shall be fully segregated with metal partition from the adjacent capacitor in order to limit the damage to other sections in case of a capacitor failure. Suitable LED illuminated ON & OFF push buttons indication lamp shall be provided on the door of switchgear compartment.

Incomer :

160 A, 415 V, TPN MCCB with door interlock and ROM - 1 No.

Outgoings :

i. 63 A, TP 25kA MCCB - 1 No

ii. 40A TP 25kA MCCBs - 7 Nos

i.63 A, AC3 Capacitor Duty type Contactor - 1Nos.

ii.40 A, AC3 Capacitor Duty type Contactor - 7Nos.

3. One 10 kVAr Capacitor is connected with out switching contactor for remaining permanently connected to compensate the magnetising current of the transformer.

APFC RELAY:

L&T/Beluke make APFC relay - 1 No.

Current Transformers :

All CTs shall be of 5 VA, Cl. - 1.0 for metering.

1. 160/5 A, 5 VA, Cl. 1.0 - 1 set.

Meters :

CT connected Ammeters

Indication Lamps :

1. LED type R,Y,B coloured indication lamps on the incoming side - 3 Nos.

2. LED illuminated Green coloured ON PB on the capacitor side - 8 Nos.

3. LED illuminated Red coloured OFF PB on the capacitor side - 8 Nos.

32A Bakelite fuse carrier & bases with 2A HBC Fuses :

1.For Indication Lamps at the incomer- 1 set (3 nos.)

2.For Voltage leads of APFC Relay - 1Set(2 Nos.)

3.For ON/OFF LED Illumination Push Buttons - 10 Nos.

4.Neutral Links on 32A bakelite fuse carrier & bases- 2 Nos.

Ventilation :

Thermostat ( 50° - 80° C) controlled ventilation fan 200 mm sweep - 1 No.

Bus bar :

250A aluminum Busbar

Earth bus : 25 x 5 mm Copper.

Capacitors :

Heavy duty two layer dielectric type (film + paper + foil), 440 V capacitors of the following ratings.

1. 415 V, 20 kVAr - 1 Nos

2. 415 V, 10 kVAr - 5 Nos

2. 415 V, 5 kVAr - 1 Nos

Supply of 3 core 300 sqmm , XLPE Armoured aluminium conductor cable of 11 kV grade as required.

Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. 3X10sqmm

7X2.5sqmm Cu with termination(for DG control cable)

Providing & fixing in position 1000 mm wide , Electrical Insulating Mats as per IS 15652:2006, 2.0mm thick, suitable for 1.1 KV , fire retardant,no effect of acids, alkalies and transformer oils, moisture proof, high tensile strength and texture finish / cloth impression (Anti slip,marking on top) .

Providing & fixing in position 1000 mm wide , Electrical Insulating Mats as per IS 15652:2006, 2.5mm thick, suitable for 11 KV , fire retardant,no effect of acids, alkalies and transformer oils, moisture proof, high tensile strength and texture finish / cloth impression (Anti slip , marking on top) .

Supply of Rubber gloves of 11KV grade as per IS 4770-68.

Supply and fixing of Shock treatment chart duly mounted on a wooden frame with glass on front as required in 2 languages (Hindi & English)..

Supply and fixing of First aid box as approved by St. John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963.

Providing and fixing of 4 Nos. 9.5 Litre capacity GI bucket painted in post office red colour with prior coat of red oxide paint and written with white paint ‘FIRE’ and mounted on MS angle iron frame with bracket of appropriate size & capacity I/c filling sand etc.

Supplying & Installation of suitable 2Hp Monobloc pump B.S or K.S.B or equivalent make with finolex cable 1x3x2.5 squmm(upto 50mtr) with flexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as MCB of 0-25Amp (Havell or Indocopp or MDS make), Volt & Ampere meter (AE make), single phase preventer (Minilac or VSP -1 make) starter (L&T or BCH make) etc of approved make, 40mm HDPE Pipe (25 mtr) and all accessories complete as per requirement of site.

Supply, Laying, Testing & Commissioning of CAT6 (RJ-45) I/O Ports

Supply, Laying, Testing & Commissioning of CAT6 Patch Panel

Supply,Installation,Testing &Commissioning of CAT6 Patch Cord with Moulded boots Over-moulded boot at each end provide strain relief and maintains minimum bend radius of the cable.- 1 Meter

Supply,Installation,Testing & Commissioning of CAT6 Patch Cord with Moulded boots, Over-moulded boot at each end provide strain relief and maintains minimum bend radius of the cable - 2 Meter

Supply, Installation, Testing & Commissioning of 6U Network Rack with below specifications as minimum and all the necessary accessories - Height - 9U - Dimensions - 550 x 450 - PDU 6 point - 1 Nos's - Mounting Hardware Kit (1 lot) - Tray - Front glass doors and back steel door and side panels

Supply, Installation, Testing & Commissioning of 16 Port Network Switch with 16 No's of 10/100/1000 ports and 2 Gigabit Copper/ SFP Combo ports for uplink

Supply, Installation, Testing & Commissioning of Ethernet RJ45 SFP Module

Supply, Installation, Testing & Commissioning of Digital PBX with 4 Trunks and 16 Analog Extensions

Supply of User Phone- Analog phone

Supply and installation of Co2 Fire Extinguisher (Trolley Mount - Wheel Operating) Type 4.5KG with MS clamps etc. for fixing on wall/wooden partition with 01 year warranty. I.S. No. 13849.

Supplying and installing in position of 6W, 240 V, 1 ph, 50 Hz indoor type LED sign boards of size (180 X 300 mm) with battery backup. Indicating the following. Samples has to approved by the Architect/Client before procuring the same. EXIT

Supplying and installing in position self glowing sign boards of sixe (150 X 400 mm) made of luminescent safely, rigid sheet in green colour, photo luminescent ACP sheet in protective glass with two hanging chains & necessary supports to hang it on ceiling. Samples has to approved by the Architect before procuring the same of the following signs EXIT

Supplying and installing in position self glowing "FIRE ASSEMBLY POINT" sign boards of size (150 X 300 mm) made of luminescent safely, rigid sheet in green colour, photo luminescent two foam sheet fixed on the wall. Samples has to approved by the Architect before procuring the same.

AIR CONDITIONING SYSTEM Supply, installation, testing and commissioning of 2 TR, Hot and Cold, 3 star rated (as per BEE) Air Cooled High Wall mounted Inverter type Split Air Conditioner consisting of high wall mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation 4m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. Make: Voltas, Toshiba, Blue Star, Siemens, Mitsubuishi, Hitachi or equivalent or as per the approval of Engineer in Charge

Supply, installation, testing and commissioning of 1 TR, Hot and Cold, 3 star rated (as per BEE) Air Cooled High Wall mounted Inverter type Split Air Conditioner consisting of high wall mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation 4m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. Make: Voltas, Toshiba, Blue Star, Siemens, Mitsubuishi, Hitachi or equivalent or as per the approval of Engineer in Charge

Provideng & fixing of Table of size 1800mmW x 900mmD x 750mmH, table top 25mm Duck nose profile on top(front & back) by pasting 0.6mm thick flex laminate in contrast colour, rest all 2 sides covered with 2mm thick PVC edge banding in contrast colour, vertical legs & modesty panel made up of 18mm thick PLPB with 2mm thick PVC edge banding, two number of PVC wire manager hole cut out on top as per requirement, all wooden panels cleaning corner knitted finish, wooden panels, gables & modesty fix joints with minifix dowels & other fitting equipment, all wooden panels made of prime quality board with ISI marking. Mobile Pedestal of size 400mmW X 485mmD X 665mmH, top 25mm Duck nose profile on top (front side) by pasting 0.6mm thick flex laminate in contrast colour, all 3 sides covered with 2mm thick PVC edge banding in contrast colour, vertical panels & bottom made up of 18mm thick PLPB with 2mm thick pvc edge banding, back panel made up of 9mm thick PLPB, four number of castor wheel to be used, all three drawers should have S.S handle, one number of lock to be used for all three drawers.

High back revolving chair of overall dimension:- 710mm W x 710mm D x 1050mm H. Seat & Back should be made of 12mm thick hot pressed plywood pasted with PU moulded foam & fabric upholstery, back fixed with mechanism through metal powder coated spine bracket, the foam should have density 45 kg/m3. Seat size: 460mm W x 470mm D x 60mm thick & back size: 490mm W x 640mm H x 60mm thickness. Mechanism: The synchro tilt mechanism in the chair allows the person’s feet to stay flat on the floor when the chair is tilted backward, seat & back moves in 2:1 direction with multi position locking, tilt tension knob to loosen or tighten the tension according to users bodyweight. Gaslift: Gaslift should have lift of 100 mm class IV grade, plastic gas lift cover. Armrest: Injection moulded fixed Poly propylene armrest to be fixed with the seat. Chair base & wheels: Revolving pedestal metal inserted PPCP base consists of 5 prongs with 660 mm pitch circle diameter, 50mm dia. black nylon - twin wheel pin castor [Dimensonal Tolerence +/- 10mm]

Four door full height cabinet overall size 1500mm W x 486mm D x 1980mm H. The cabinet should be designed to use with 2 separate users with 2 separate locks. Top & bottom made up of 25mm thick PLPB material with 2mm thick PLPB edge banded finished with approved laminate shade, vertical panels, and shelves & under structure made up of 18mm thick PLPB material with 2mm thick PVC edge banding. Three number shelves provided in each side, doors to be made up of 18mm thick PLPB with 2 mm thick PVC edge banding, doors should have metallic hinges with all fittings. The cabinet back made up of 9mm thick PLPB material, 75mm skirting provided at the bottom, storage provided & fixed with mini-fix, screw, locks & handles, all wooden panels, shelves & shutter fix joints with mini-fix dowels & other fitting equipment, wooden panels cleaning corner knitted finish, all wooden panels to be made of prime quality board with ISI marked.

Three-seater waiting sofa of overall size 1800mm W x 670mm D x 785mm H. Seat height 425mm. Seat & back made of 1.2mm thick perforated CRCA sheet metal duly powder coated in silky silver base frame beam 80mmH x 40mmW x 1795mmL & 1.82mm thick, height of the seat from floor 425mm, beam made of MS ERW rectangular tube black powder coated, legs & armrest chrome plated rectangular MS structure, bow shaped 1.2mm thick sheet, Perforated seat & back fixed with MS brackets duly powder coated, beading chrome plated MS channel beading, level adjuster chrome plated MS cap with PVC inserted black colour, all pipes shall be welded properly and strongly and conformity with regulations.

Supply of Medicine Rack of Size 660 (L) x 415 (W) x 1500 (H) mm. 11 Nos of shelves, 3 nos of high quality impact resistant plastic pull out Trays in each shelf & 1 Nos kick Plate. Each Tray of (WxDxH) 415 x 220 x 135mm.

Supply of SS Revolving Stool with 100 Kg Capacity of 300mm seat dia, Height adjustable 450mm to 680mm. 3 legs tubular base, Revolving top, Legs fitted with shoes 16 & 18 Guage Pipe, 1MM Sheet.

Design, providing and fixing Digital Printed vinyl signage boards with transparent 3mm acrylic Sheet with 4 nos. SS Studs of Size 16" x 10". Complete as per the per the direction of Engineer in charge.

Design, providing and fixing Acrylic LED Sign Board of 5cm Letter Thickness 20 - 30cm Letter Height. Complete as per the direction of Engineer in charge.

Patient Cot : PLAIN 32D Mattress , 2100X930X520MM , BED FRAME 2030X900MM OR MORE 25X50MMX1.5 MM FRAME, 32X32X1.5MM HEAD AND LEG  Overall size (Approx): 200 (L) x 90 (W) x 60 (H) cms.  Tubular Bows (outer pipe) made of 30mm x 18 G CR ERW pipe.  Top made of rectangular/square frame of 50mm x 30mm and made up of 16  SWG M.S tube.  Bed top should be of 18 G MS CRCA ribbed perforated sheet.  Provision for IV attachment system (No bend hook) at the both head side of  the bed.  All metallic parts of the bed should be pre-treated to achieve rust free clean  surface prior to epoxy powder coating.  Warranty: 1year

Oxygen Concentrators 5L CE and USFDA Approved, Longfian/Qanta Make  Oxygen concentrator to provide oxygen from ambient air.  Oxygen concentration should be measured at the flow meter by oxygen sensing device (OSD)  Should have oxygen purity indicator/alarm for low oxygen concentration.  Sound level ≤55 dB  Superior grade of molecular sieve bed of minimum working hour of 15,000hrs.  Integrated Timer should be there.  Should have audio and visual alarm for Low oxygen concentration, low pressure and power failure.  The unit should be movable and should be provided with four wheels with at least two breaks.  Oxygen concentration 90% ±3% at 15LPM flow.  Oxygen output, approx.: 0.5 to 15 LPM or better.  Oxygen outlet Pressure: Minimum 15 psi.  Double outlet for oxygen Delivery controlled from two separate pressures compensated flow meter to ensure accurate flow display.  Masks: Necessary mask suitable to Adult should be provided: 2 sets.  Supplied with Spare set of tubing: 2No, Spare set of internal and external filters (bacterial): 2Nos, Humidifier bottles: 2Nos, Cabinet filters: 2Nos, Spare set of fuses: 2Nos.  Power Supply Power input to be 220-240VAC, 50Hz fitted with Indian plug.  Should be USFDA or CE or BIS approved model.  Manufacturer should be ISO 9001 & ISO 13485 certified for quality standards.  Should be comply IEC 60601-1 for electrical safety.  Warranty: 1year

Bed Side Locker S S Top, Drawer ,One storage cabinet, dimensions: 160x160x320mm Ashman/Genuine/Godrej/Durian/Geeta or equivelent Make  Should have an enclosed locker unit which is provided with 50 mm dia non rusting castors for mobility.  A stainless Steel tray top with raised borders on 3 sides forming the upper surface.  Drawer should be fitted with smooth slides.  Should be provided with shelf space for storage under the Drawer with locked Cabinet at below. Drawer and cabinet should have front door.  Should have one drawer & one cabinet box with self-space in between.  The body should be made of 20 G MS CRCA sheet.  All MS parts to be pre-treated and epoxy powder coated.  All SS to be of 304 Grade and of 16 Gauge.  Should be a ISO certified manufacturer.  Warranty: 1year

Finger tip pulse oximeter PI% and Perfuson Index, Auto Rotation CE AND USFDA approved  Should have automatic multi directional display format and should display spo2%, PR, PI and plethysmograph.  Should haveSpO2 measuring range of 0-100%.  Should have measuring range of Pulse rate 30bmp to 250 bmp.  Should have measuring Accuracy - +/- 2 bpm or +/-2%.  Should work in low perfusion and PI should be displayed.  Default Alarms for lower and higher limits of spO2 and Pulse Rate.  Should have facility for auto shut off if finger is not inserted.  Should consume low power <30mA.  Optical wave length of sensors should be: Red: 660nm, 6.65mW, Infrared: 880nm, 6.75mW.  Should work continuously on batteries with a backup of 20hrs.  Should be certified CE or USFDA or BIS  Warranty: 1year

Suction apparatus - Foot SUPREME/ANAND  High performance suction pump for pharyngeal and tracheal suction  Double acting piston pump provides a combination of large airflow and high vacuum  See-saw movement of pedal generates suction every time one side of the pedal is depressed  Pump chassis complete with valve diaphragms, manifold pipe, bottom cover, cylinder with draw link and valve diaphragm, piston O-ring, pedal with retaining springs, aspirating tube with angle connector and combination suction tip  Pump can be totally disassembled, is easy to clean and disinfect  All parts can be autoclaved at 121°C  Vacuum, max: 400 mmHg  Free airflow at two pumping strokes per second, approx: 30 to 40 L/min  All parts made of high-strength, long-life materials, not requiring specific maintenance or storage  Transparent polycarbonate collection container capacity, approx: 1 L  Bottom cover: thermoplastic rubber  Manifold pipe: polypropylene  Gasket, O-rings and valve diaphragm: silicone rubber  Piston rings: Teflon  Foot pedal: Aluminum  Device is produced by ISO 9001 certified manufacturer  Device is safety certified according CE 93/42, FDA 510k or equivalent Supplied with: • 1x set of silicone rubber suction tubing, approx: diam. 10 mm, length 1.5 m • 1 x angle connector and combination actual suction tip • 1 x spare valve diaphragms • 1 x spare piston O-ring • 1 x spare retaining springs, • User manual with trouble shooting guidance, in English • Assembly, Installation and Training at end-user site Warranty: 1year

Glucometer with 500 strip 20 12% 900 11,200 STRIP NISCOMED/DR MOREPEN  Should be a hand held meter  Should require no routine maintenance  Should have reading range/linearity from 10 to 600 mg/dl  Should have a maximum reading time of less than 10 seconds  Should use electrochemical technology  Should use a minimum blood sample less than 1.5µl  Should have a LCD display  Should have measuring unit in mg/dl.  Should have wide operating temperature  Should have a minimum memory of 50  Should have life time replacement offer  Should have automatic code entry technique  Battery should be replaceable without using any tools.  Should have facility to ensure accuracy of measurements.  Should be supplied with 100 strips  Device is produced by ISO certified manufacturer.  Warranty: 1year

AMBU bag Adult  Resuscitator for manual ventilation of Adult  Ventilation can be done with ambient air or with oxygen  Resuscitator can be totally disassembled, is easy to clean, disinfect and sterilize  All parts can be autoclaved at 120°C (except O2 reserve bag)  Manufactured from durable high-strength synthetic not requiring special maintenance or storage  Resuscitator is supplied as a complete set in a box  Compressible self-refilling ventilation bag, capacity, approx. 500 ml  With non-re breathing patient valve with pressure limitation  Intake valve with nipple for O2 tubing  O2 reserve bag complete, capacity approx.: 2000 ml  2 Nos of cushioned neonate size masks, translucent of each (Size “0”, approx: 50 mm)  Device is produced by ISO certified manufacturer  Device is safety certified according BIS/CE/USFDA or equivalent  Warranty: 1year

Oxyge Cylinder (D Type) with Trolley  For carrying 47 kg  To Carry big size Cylinder  It shall carry load of 50-60 kgs Its dully powder coated and shall have 2 castor wheels  Trolley base shall be a non-strip rubber mat  ISO certified manufacturer.  One year warranty  Warranty: 1year

Flow meter with humidifier GHL PRODUCTS/SD PROCESS / Pii Healthcare Make  Back Pressure Controlled Flow Meter.  Sturdy and reliable Flow Meter Unit for an accurate measuring of flow of gases.  Chromium plated Brass Body.  Metering tube and cover made of unbreakable Poly carbonate.  Flow rate range 0 – 10 litres / minute.  Inlet pressure suitable for the cylinder.  Should be supplied humidifier bottle and mask.  Warranty: 1year

Wheel chair- MS Weight Capacity upto 250 LB Foldable  Size: 790 mm (L) x 600mm (W) x 780 (H)  Structure: made of 22x1.2 mm SS 304 grade  Finish: Chrome finish  Crossbar: 25.4x 1.2mm thick  Material: S.S Tubular framework fitted with S.S Seat and back of grade SS 304.  Wheels: Two solid PU wheels and self-propelling S.S Loops. Two swivel castors 100 mm diameter in front.  Arm rest: ABS plastic  Foot rest: Aluminium die cast  Should have cushion for seat.  Should be an ISO certified manufacturer.  Foldable  Warranty: 1year

Weighing Scale digital WEIGHING SCALE DIGITAL Weighing Scale have high precision strain gauge sensors with a capacity of 180 kg and denominations up to 0.1 kg Additionally, weighing scale comes  Weighing capacity should be up to 200kgs.  Reading time max 5 seconds.  Display should be wide window for clear & better visibility.  Should be robust construction and platform type.  Should provide accurate reading.  Device is produced by ISO certified manufacturer.  Warranty: 1year

Clinical Thermometers(Digital) -  Digital thermometer Celsius scale with switch to Fahrenheit  Safe to use, atraumatic, no glass, no mercury  Measurement range: 32°C to 43°C  Accurate measurement: +/- 0.10°C between 35°C to 41°C  Liquid crystal display, easy to read  Beep sound and switch off  Water proof for ease of cleaning  Battery powered  Low battery indicator  Device is produced by ISO certified manufacturer  Supplied withSuitable battery  Warranty: 1year

BP Apapratus(Digital)  Display: LCD Digital display  Measurement range: Pressure 0 to 300 mmHg pulse40-180 beats / min  Accuracy / calibration: Pressure: + 5% of reading  Battery life :Approx 1500 uses when used twice a day  Main unit weight: Approx 340g excluding batteries  Cuff size: 3 cuffs - adult, paediatric &neonatal size(one each)  Cuff should be highly durable  Cuff circumference: Should Fit arm circumference around 220mm to 320mm  Battery with charger: One charger & four rechargeable batteries  Should be supply additional cuff for adult, paediatric and neonatal (each one)  Warranty: 1year

Stethoscope  Chest piece in aluminium.  Fixed Diaphragm approx: 25 mm.  Should be of soft sealing ear tip type  Y tube: treated rubber with large diameter.  Removable plastic ear-pieces  Approximate length should be 70 cm.  Total weight should be less than 200 gms  Device is produced by ISO certified manufacturer  Warranty: 1year

Nebulizer(Ultrasonic) CITIZEN/EASYNEB MaKE  Method of Nebulization - Piston Driven power 240v 50Hz  Max Pressure (Compressor -30 psi or better  Flow range - 0 -14 litres/min or better  Particle size - 0.5 to 5 microns or better  Capacity - 5 ml or better  Mask combatable - Adult,Paediatric, Neonatal  1year warranty

Syringe destroyer with Needle Cutter S GMPL/ASHMAN MAKE  Cuts the syringe within seconds  Low power consumption  Can destroy syringes from 18 gauge to 28 gauge  On/off switch with a pilot lamp  Comes with a shock-proof main circuit breaker  Very portable, compact and handy to use  Warranty: 1year

Patient trolley- MS GMPL/ASHMAN MAKE  Size: 2000mm (L) x 660mm (W) x 830mm (H)  Main frame: 32mm OD x 1.6 mm Thick M.S ERW  Supporting frame: 25mm OD x 1.6 mm Thick M.S ERW  Castor wheels with 200 mm dia.  locking castor wheels  Stretcher top frame 25mm OD x 1.6 mm Thick M.S ERW  Sheet should be made of CRCA of 1.2mm thickness  Provision for IV pole.  Max. Load of 500Kg  Finish: powder coated with antimicrobial epoxy polyester powder.  Should supply with Stainless Steel stretcher and removable mattress (washable)  Should be an ISO certified manufacturer.  Warranty: 1year

Equipment Trolly EQUIPMENT TROLLEY GMPL/ASHMAN MAKE  SS tubular frame work made of 25.4 mm OD x18G verticals mounted on 125mm dia. Non rusting castors two with brakes  Castors to be made of high grade non floor staining synthetic materials with integrated thread guards. Wheel centres having precision ball bearing to run smoothly  Two stainless steel shelves of 20G thickness with protective railings on 3 sides. The railings shall be made of dia. 10mm SS rod  Only 304 grade SS should be used for trolley frame work and burr free SS shelves  SS parts finished with Matt polish and must be supplied in SKD condition  All process parameters to be as per documented IMS procedures for quality assurance must be compliant to ISO 9001:2008  Manufacturer should be ISO and/or 9000:1 and/or 14000:1 and/or 18000:1 and/or BIFMA certified  Warranty: 1year

Crash cart EQUIPMENT TROLLEY GMPL/ASHMAN MAKE  Overall size shall be more than 900mm L x 500mm W x 1500 mm H.  The crash cart should be made of SS grade tabular frame and SS sheet grade.  Should have push handles  Should have SS Shelves, Six colour removable bins & two polystyrene lockable storage units with three drawers each.  Facility to carry any Monitors or Defibrillators, etc. On open areas at top and bottom shelves.  Should have Stainless rods fixed with.  Two accessory mounting brackets to mount accessories anywhere without the need of pre-threaded holes.  Crash cart should be mounted on 12.5cms dia non-rusting swiveling castor wheels, two having locking arrangement.  It should be robustness in quality.  Device is produced by ISO certified manufacturer  Warranty: 1year

Add 18% GST

Add 1% Labour cess 1%

HEIGHTEN CONSTRUCTIONS