CERTAIN REPAIR TO SEPTIC TANKS SOAKAGE WELL MANHOLES SEWAGE LINE AND DRAIN IN TECH AREA AT AF STN SURATGARH

Amount

BOQ (CERTAIN REPAIR TO SEPTIC TANKS SOAKAGE WELL MANHOLES SEWAGE LINE AND DRAIN IN TECH AREA AT AF STN SURATGARH)

M & L for cleaning of all blockages of Nahani traps/floor traps/bottle traps, blockages of WC's, 100 mm dia CI pipe upto 1st manhole/GT in shafts, vertical CI soil/waste pipe stacks, CI Tee/door bends etc to maintain uninterrupted sewage system by employing Safaiwala from 0900 hours to 1700 hours with permissible lunch break on daily basis with manual/pressure cleaning pump and flexible rods and other necessary mechanical equipments all as directed by Engr-in-Charge. Note : (i) Supervisors should received everyday complaint through MES Complaint register. (ii) Penalty in case not attending to each complaint during same working day will be recovered from contractor @ Rs.50 per complaint. (iii) Rate included for all necessary T&P for Mechanical cleaning / manual cleaning shall be provided by Contractor. (iv) The Disposal of mud/silt, sludge & other debris retreived from cleaning should remove outside of MOD premises complete all as specified and directed by Engr-in-Charge (v) If necessitated by JE/Engr-in-Charge/ GE, contractor will provide to attend the complaints as required on Sunday/ holidays.

Cleaning of pipe drains by rodding 150 mm internal dia of drain pipe upto 2.0 mtr in depth and removal of sludge/silt/liquid mud sand (in foul conditions) etc out of MOD premises including testing of drains by filling the pipe with water. (Depth to be measured from existing level to invert level of pipe) complete all as directed and specified by Engr-in-Charge.

All as per item No 2 above but cleaning of 200 mm internal dia of drain pipe depth upto 2.5 metre complete all as directed and specified by Engr-in-Charge.

Cleaning of manholes upto 1.5 metre depth and removal of sludge/silt etc in foul conditions to outside MOD land including testing of manholes by filling with water complete all as specified and directed by Engr-in-Charge.

Cleaning of manholes depth exc 1.50 m and not exc 3 metre complete all as specified and directed by Engr-in-Charge

Cleaning of Grease trap tank by taking out the sludge mud/silt etc and removing to outside of MOD premises complete all as specified and directed by Engr-in-Charge

Removing the drain cover set in CM and cleaning the drain including desilting the mud/debries etc and resetting the drain cover in cm (1:4) of any width of drain n exc 60cm and depth n exc 5m and removing the garbage out side the defence premises at the discretion of Engineer-in-Charge complete all as specified and directed.

De-watering of septic tanks/soakage wells and sewage line by pumping with trolley mounted pump sets including carrying the waste water in closed containers and unloading it out side the MoD land at location shown by Engr-in-Charge at a distance n. exc 5 km from the starting point including removing the existing manholes cover and replacing the same, septic tanks/soakage wells of any size/depth complete all as specified and as directed by the Engr-in-Charge

Cutting and grubbing of bushes, grass and tree surrounding manholes, gully trap, bend, wall pipe and overhead tank etc and levelling of ground around the manholes and finish the surface of wall and removing the waste material to distance exc 50m and n exc 250m and clearing the site complete all as specified and directed

Demolition in cement concrete (unreinforced) in ground floor and pavings n. exc 15cm thickness (below or above ground level) complete all as specified and directed

M&L for PCC 1:3:6 type C2 (using 40mm graded aggregate) as in foundations or mass concrete complete all as specified and as directed by the Engr-in-Charge

M&L for PCC 1:2:4 type B2 (using 40mm graded aggregate) in surface channels and drains complete all as specified and as directed by Engr-in-Charge

M&L for PCC 1:2:4 type B1 (using 20mm graded aggregate) as in coping including necessary form work complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed by the Engr-in-Charge

Excavation in trenches in soft/loose soil, n exc 1.5m wide and n. exc 1.5m in depth, for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm in soft/loose soil

Removing excavated soil exc 250m but not exc 500m and depositing where directed at a level n. exc 1.5m above the starting point

Demolition and breaking up drain pipes 150mm bore set in cement mortar, complete all as specified and directed.

Demolition and breaking up drain pipes 200 mm dia set in cement mortar complete all as specified and directed.

M&L double wall corrugated drain pipe ' DWCPE' (SN8) 180 mm (OD)/ 152 (ID) mm diameter, (ISI marked)laid in trenches and tested including fittings of same grade complete all as specified and directed .

M&L double wall corrugated drain pipe ' DWCPE' (SN8) 200 mm (OD)/ 175 (ID) mm diameter, (ISI marked)laid in trenches and tested including fittings of same grade complete all as specified and directed .

M&L for salt glazed stoneware drain pipes grade 'A' 150mm internal dia laid in trenches and jointed complete all as specified and directed.

M&L for cement concrete 1:3:6 type C2 (using 40 mm graded aggregate ) concrete bed to drain pipes with thickness of bed below the barrel of pipe as 100mm and width of bed as 450mm to drain pipes of 150mm internal dia including packing under, and completely surrounding pipes with concrete after they are laid and tested complete all as specified and as directed by Engr-in-Charge

M&L for cement concrete 1:3:6 type C2 (using 40 mm graded aggregate ) concrete bed to drain pipes with thickness of bed below the barrel of pipe as 150mm and width of bed as 500mm to drain pipes of 200mm internal dia including packing under, and completely surrounding pipes with concrete after they are laid and tested complete all as specified and as directed by Engr-in-Charge

Cutting into existing Manholes for connecting new drains , 150mm dia, making good to pipes and rendering , cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required complete all as specified and as directed by Engr-in-Charge

Demolition of Brickwork or stone/boulders masonry built in cement mortar complete all as specified and as directed by the Engr-in-Charge

M & L for Brick work with sub-class `B' bricks, straight or curved on plan to for any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 (except bricks) complete all as specified and as directed by Engr-in-Charge. Note- Bricks retrieved from items No 26 shall reused after proper cleaning.

M&L for brickwork with subclass 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified and directed

Taking down cement or cement lime plaster on brick or stone walls including racking out joints/hacking for key, scrubbing down with water etc complete all as specified and as directed by Engr-in-Charge

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surfaces finishing even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge

M &L for applying two coats of exterior acrylic emulsion (weather proof treatment), in camouflaging patterns , including preparation over new plastered surfaces complete all as specified and directed.

M&L for 1.5 mm thick birla/JK wall care putty to receive smooth finishes complete all as specified and directed.

M&L for preparation of old surfaces of walls including brooming down or steel wire brushing scraping down smoke soot, moulds mass and efflorescent salt and trading oil and greasy spots applying two coats of distemper oil emulsion on wall complete all as specified and directed by Engr in charge.

M&L for preparation of old surfaces of ceilings including brooming down or steel wire brushing scraping down smoke soot, moulds mass and efflorescent salt and trading oil and greasy spots applying two coats of distemper oil emulsion on ceilingsl complete all as specified and directed by Engr in charge.

M&L for water proofing layer with Dr. Fixit Primeseal external wall waterproofing as per company instruction all as directed by Engr-in-Charge.

Demolition of RCC of any description in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition)

M&L for precast cement concrete 1:2:4 type B1 (using 20 mm graded aggregate) as in manhole covers set in CM 1:4 complete all as specified and as directed by Engr-in-Charge

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed

M&L for PCC 1:3:6 type C2 (using 40 mm grade aggregate) 75 mm thick as in pavings finished even and rough to receive top layer and as directed by Engr-in-Charge

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.11 but n.exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 all as specified and as directed by Engr-in-Charge

M&L for coloured Chequered cement concrete tiles 20 cm x 20 cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments over and including 15mm thick screed bed of cement mortar 1:6 complete all as specified and as directed by Engr-in-Charge

M&L for Glazed colour ceramic tiles in vertical surface 300mm x 200mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for 20mm thick Granite (of any type ) tiles machine cut, in skirting/dado over and including 10mm thick screed bed in cement mortar 1:4 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed by Engr-in-Charge

S&F in 100mm bore cast iron sand cast pipes waste and vent pipes in any lenth with or without ears, jointed with lead joints, fixed to wall or laid in trenches / in floors complete all as specified and directed.

S&F in 75mm bore cast iron sand cast pipes waste and vent pipes in any length with or without ears, jointed with lead joints, fixed to wall or laid in trenches / in floors complete all as specified and directed

S&F in 50mm bore cast iron Sand Cast pipes waste and vent pipes in any length with or without ears, jointed with lead joints, fixed to wall or laid in trenches / in floors complete all as specified and directed.

Dismantling of cast iron pipes jointed in cement mortar & taking out of branches if required

S&F in repairs 75 mm CI bends (any radius), diminishing pieces or tapers of complete all as specified and directed .

S&F in repairs 100 mm CI bends (any radius), diminishing pieces or tapers of complete all as specified and directed by Engr-in-Charge.

S&F in repairs 75 mm bore Tee/branch piece single (Equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engr-in-Charge.

S&F 75mm cast iron floor trap, with grating including jointing to waste pipe fixed in cement concretetype B1(1:2:4), fixed in repair complete all as specified and directed.

S&F 75mm cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4), fixed in repair complete all as specified and directed.

S & F 110 mm bore PVC (SWR) Soil, pipes double socketed in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed.

M&L PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement, fixed in repair complete all as specified and directed. .

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting exc 10cm but n exc 20cm girth. complete all as specified and directed.

Taking up or down 15mm steel water tubing and connection incl cleaning for refixing or removal to stores.

Taking up or down 20mm steel water tubing and connection incl cleaning for refixing or removal to stores.

S & F 15 mm bore Galvanised teel tubes, medium grade with all fitting fixed to walls and ceilings or laid in floors complete all as specified and directed.

S & F 20 mm bore Galvanised teel tubes, medium grade with all fitting fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F 10 litres capacity PVC valveless, Syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets in repair complete all as specified and directed.

S&F Vitreous China Squatting pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe) in repair complete all as specified and directed.

S&F Vitreous China wash down water closed pan (Pedestal pattern) white , including connection to drain(or out going pipe) and to flush pipe, antisypthonic (excluding flushing cistern and flush pipe) in repair complete all as specified and directed.

S & F in repairs Vitreous chinabowl urinal flat back size 465 x 355x 265 mm white minimum with grating and union for discharge pipe , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, point complete all as specified and directed.

S&F 15mm dia Cast copper alloy, Chromium Plated Bib taps fancy type with crutch or butterfly handle, screwed for iron pipe or for brass ferrule and fixed in repair complete all as specified and directed.

S&F 15mm dia Stop valve fancy type, chromium plated with long shunk and cup (concealed type) screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed in repair complete all as specified and directed.

S & F 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe. complete all as specified and directed.

S&F Stainless steel grating 125mm dia fixed in repairs all a specified and directed.

S&F Grating doom 125mm dia with waste hole of PTMT (Minimum weight 40 gms) complete all as specified and directed.

S&F in repairs Vitreous China Wash Hand Basin white flat back of size 550x400mm excluding taps waste, chain and plug but including brackets complete all as specified and as directed by Engr-in-Charge

S&F SFRC manhole cover slabs medium duty of any shape and size required and 65mm thick complete all as specified and directed by the Engr-in-charge.

Rough Excavating over areas, n.exc 1.5m deep and getting out in soft/loose soil complete all as specified and directed.

Rough Excavating over areas, exc 1.5m and n.exc 3m deep and getting out in soft/loose soil complete all as specified and directed.

Rough Excavating over areas, exc 3 m and n.exc 4.5 madeep and getting out in soft/loose soil complete all as specified and directed.

M&L Hardcore of gauge n. exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface in broken all as specified and directed. stones or boulders all as specified and as directed by Engr-in-Charge.

M&L Cement concrete 1:4:8 Type D2 (using 40mm graded stone aggregate) as in foundations or mass concrete complete all as specified and as directed by the Engineer in Charge.

M&L for Brick work in cement mortar 1:4 using sub class B bricks straight or curved on plan exceeding 6m mean radius complete all as specified and as directed by the Engineer in Charge.

M&L for cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) in copings, cills , steps, seismic and other similar bands , plinth cources , string cources and other similar articles complete all as specified and as directed by the Engineer in Charge.

M&L for Brick work in cement mortar 1:4 using sub class 'B' bricks in one brick thick honey comb work complete all as specified and as directed by the Engineer in Charge.

M&L for loose filling with aggregate of broken stone or boulders of gauge 40 to 80mm in soakage pits, soakage wells complete all as specified and as directed by the Engr-in-charge

M&L for mild steel TMT bars 6mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works, not exceeding 200mm thick (horizontal or sloping) in flat rough finished surfaces of concrete complete all as specified and directed by Engr-in-Charge

Contract Amount shall be derived after deducting the amount of Schedule of Credit in General Summary on serial page No 17 of tender documents.

M/S Shree Ram Enterprises

PG CONSTRUCTION AND COMPANY