SPECIAL REPAIR TO COMPOUND WALL OF STP AT VIJAY BAUGH AND CERTAIN SANCTIONED WORKS UNDER GE HADDO SRI VIJAYA PURAM

M&L for cement concrete (1:2:4) Type B-2 (using 40mm graded stone aggregate) as in surface channels or drain, etc completed all as specified and as directed.

M&L cement concrete (1:2:4) type B-1 using 20mm graded aggregate as in lintle upto 1.5m clear span, steps, bed plates, kerb & coping including necessary formwork, etc completed all as specified and as directed.

M&L precast cement concrete block masonry exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6), etc completed all as specified and as directed.

M&L for pre cast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in manhole cover slab set in cm 1:6, etc completed all as specified and as directed.

M&L precast cement concrete block masonry not exc 10 cm width with solid block PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) and setting in cement mortar 1:4, etc completed all as specified and as directed.

M&L for nominal mix RCC 1:1.5:3 type A1 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajja/facia and the like , etc completed all as specified and as directed.

M&L for nominal mix renforced cement concrete type B1 1:2:4 ( Using 20 mm graded stone aggregate) as in Columns,pillars,piers,posts and struts etc complete all as specified and as directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.including grinding and polishing, etc completed all as specified and as directed.

M&L formwork for rough finished flat surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) , etc completed all as specified and as directed.

M&L formwork rough finished surface of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work n. exc 10 cm wide, etc completed all as specified and as directed.

Supply only Aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples, etc completed all as specified and as directed.

Supply & fabricate and fixing in position angle iron posts for fencing posts and struts including flat iron etc and including cutting tops to shape as directed , drilling holes, notching for wire etc flat iron fillets for securing fencing including all necessary welding , drilling, bolting or riveting,confirming to Fe-290 (Gde E-165), etc completed all as specified and as directed.

M&L for Mild steel screw bolts (machine made) with hexagonal or square head one end and screwed the other, or screwed both ends each screw-wed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long diameter of neck in exc 16mm and n.exc 20 mm, etc completed all as specified and as directed.

M&L for mild steel round bars 10 to 12mm dia as required, made to shape for securing chain link fencing etc., and similar works conforming to Fe-290 Gde E-165 and including preparation and applying two coats of synthetic enamel paint over a coat of red oxide primer before fixing, etc completed all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, etc completed all as specified and as directed.

M&L for mild steel TMT bars 6 to 8 mm dia , cut to length, bent to shape required, including cranking, ties for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

S&F in repairs for Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specifed and directed

S&F for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

S&F for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of sliding doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene asket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, auminium snap beading for glazing/ paneling, C.P. brass/ tainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.06 Sqm but n. exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4, etc completed all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 15mm thick screed bed of cement mortar 1:4 , etc completed all as specified and as directed.

M&L for 10mm thick plaster in CM 1:6 on fair face of concrete surface or brick walls finished even and smooth without using extra cement, etc completed all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 including mixing water proofing compound on concrete/block masonry surfaces and finished even and smooth without using extra cement, etc completed all as specified and as directed.

Taking down cement plaster on brick /stone masonry / concrete surfaces of wall / ceiling incl raking out joints, hacking for key, scrubbing down with water etc and deposited the debris outside the MD land complete all as specified.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified.

M&L for complete removal of exisitng treatment and applying two coats of cement base paint over a coat of primer complete all as specified.

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth, etc completed all as specified and as directed.

M&L for preparation on newly plastered external wall surface and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint complete all as specified and as directed. (Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard), etc completed all as specified and as directed.

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, etc completed all as specified and as directed.

S&F 25mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including suitable reducer for 15mm dia taps fitting as required, etc completed all as specified and as directed.

S&F 20mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including suitable reducer for 15mm dia taps fitting as required, etc completed all as specified and as directed.

S&F fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, etc completed all as specified and as directed.

S&F PVC (SWR) pipe 75mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors, etc completed all as specified and as directed.

S&F for 75 mm PVC (SWR) branch piece, single (SingleT ) of radius equal or unequal, etc completed all as specified and as directed.

S&F in repair 75mm outlet dia PVC (SWR) floor trap with grating including jointing with solvent cement to waste pipe, etc completed all as specified and as directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm , etc completed all as specified and as directed.

Demolition of Precast cement concrete block walling built in CM or Cement lime Mortar complete all as specified and as directed.

Demolition of cement concrete un-reinforced in any position and paving not exc 15cm thick above or below ground level complete all as specified and as directed.

Demolition of reinforced cement concrete in of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for chain link fencing , etc completed all as specified and as directed.

Dismantling existing barbed wire/plain wire/ chain link fencing any type from RCC/Steel/Wdn posts, etc completed all as specified and as directed.

S&F 100mm size stainless steel butt hinges medium weight, etc completed all as specified and as directed.

S&F for MS Galvanized with 1.00mm thick PVC coated chain link fencing 50mm x 50mm over 3.15mm GI wire including fixed to any type of fencing posts with straining bolts, stiffener rods etc including provision of binding wire if required, etc completed all as specified and as directed.

Supply & Fixing Floor stand consisting of 19 mm square pipe MS powder coated base frame with a number of meshes. Each mesh has 6 rods of 202 Grade Each mesh has 6 rods of 202 Grade SSSS /; eMacSh p roowd doefr dia 5 mm and length 740 mm. Each mesh has total length of 4400 mm (approx 15 ft) of drying space, etc completed all as specified and as directed. Make : Easy Dry or any equivalent approved by Accepting Officer.

Supply and fixing Cross Arms, bracings, supports, clamps, eye hook etc structural ateel sections including pole clamps stay clamps, D clamps nuts, bolts, washers welding bending cold or hot drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coar and one finishing coat of aluminium paint complete all as specified and as directed.

M&L for Point wiring two single core 1.5 sqmm size PVC insulated, unsheathed FRLSH multistranded copper conductor cable and one single core 1.5 sqmm size green colour PVC insulated FRLSH multistranded copper conductor cable as earth continuity conductor, 1100 volt grade (with proper colour coding Red/Blue/yellow for phase, black for neutral and green for earth) complete drawn through and including PVC casing and caping not less than 25 mm width with all fittings, surface on wall/roof /floor including including sunk pressed steel terminal boxes flush mounting in the wall for mounting switches/switch socket combinations/ fan regulators etc., covered with suitable size of modular cover plates complete in making good the existing surface with existing colour coding as required at site complete all as specified for the following :- Note :- The unit rate quoted shall deemed to include the cost of following :- Make of wire : Polycab/ Gloster/ Anchor/ Havells/ Finolex/ V-Marc and Make of PVC Conduit or Casing & caping : Modi/ Precision/ Supreme/ Finolex/ Polycab. (a) GI metal flush box of minimum thickness of 1.6mm and modular cover plate with frame of any module complete. (b) Proper colour coding is to be followed as per IS specification. (c) Wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (d) Cutting chases in wall/floor /beam/ceiling to be concealed conduit and making good the disturbed surfaces.

All as per item Ser No 53 above but for One light/fan point controlled by one modular switch 5 Amps one way complete all as specified and directed

All as per item Ser No 53 above but for one modular 3 pin 5 Amps socket outlet on same Board complete all as specified and directed

All as per item Ser No 53 above but for one modular 3 pin 5 Amp socket out let on independent board complete all as specified and directed

All as per item Ser No 53 above but point wiring with 4.0 sqmm PVC FRLSH insulated multistranded copper conductor suitable for one 3 pin 16 Amps socket out let and one run of 4.0 sqmm cable for earth in green colour on independent board complete all as specified and directed

S&F for switch modular type, 6 Amps 1 module, 230 volts AC circuit complete all as specified and directed. Make : Roma (Anchor)/ Legrand/ Havells

ࠀ♓⁆潦⁲睳瑩档†潭畤慬⁲琠灹ⱥㄠ‶流獰ㄠ洠摯汵ⱥ㈠〳瘠汯獴䄠⁃楣捲極⁴潣灭敬整愠汬愠⁳灳捥晩敩⁤湡⁤搠物捥整⁤䴊歡⁥›潒慭⠠湁档牯⼩䰠来慲摮 慈敶汬潳ഀ猀؀鬀ࠀ♓⁆潦⁲潳正瑥漠瑵敬⁴潭畤慬⁲祴数ㄠ眠祡㘠䄠灭ⱳ㌠瀠湩

S & F high speed air ventilating fan 300 mm sweep single ph, 230 volt, steel body with louvers incl all fixing arrangement complete all as specified and as directed.

Each Job

Please Enable Macros to View BoQ information