Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹20.7 LAccepted-AOC | L1 | Accepted-AOC BEING LOWEST BIDDER | |
| 2 | L2₹21.0 L+₹6,381.65 (0.30%)Rejected-Finance 00 JAI BHAWANI COMPLEX MAIN ROAD SADAR WARD JAGDALPUR BASTAR CHHATTISGARH 494001 UDYAM CG 01 0003803 | BASTAR | CHHATTISGARH | 494001 | L2 | Rejected-Finance OTHER THAN LOWEST BIDDER | |
| 3 | L3₹28.2 L+₹7.3 L (34.7%)Rejected-Finance | L3 | Rejected-Finance OTHER THAN LOWEST BIDDER |
Tender Value
₹25 L
EMD Value
₹50,000
Closing Date
12 Dec 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE JABALPUR
HQ CWE JABALPUR OPPOSITE SUPPLY DEPOT SADAR JABALPUR 482001
PROVISION OF GUARD ROOM AND GATE FOR SECURITY COMPANY AT NAYA RAIPUR UNDER AGE (I) NAYA RAIPUR
2022_MES_562972_1
86047/E8
Open Tender
Civil Works
Item Rate
270 days
NAYA RAIPUR
AS PER NIT
8 documents required · 8 mandatory
₹500
Yes
AGE I NAYA RAIPUR
₹50,000
Yes
11 Jan 2023
14 Nov 2022
14 Dec 2022
14 Nov 2022
12 Dec 2022
28 Nov 2022
14 Nov 2022 - 26 Nov 2022
Amount
Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in hard / dense soil complete all as specified. and as directed.
Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed.
Ditto all as per item No. 2 above, but depth exceeding 1.50 metre but not exceeding 3.0 metre.
M & L Plain Cement Concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.
M&L for RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, etc and mass concrete complete all as specified. and directed.
M&L Formwork to flat sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter., rough finished surfaces of concrete, complete all as specified and directed.
M&L for RCC M-25 (Design mix) (using 20mm graded crushed stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.
Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square,rectangular or polygonal, rough finished surfaces of concrete, complete all as specified and directed.
M&L for RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in beams, cantilevers, bressumers, lintels over 1.5m span etc. complete all as specified and directed.
Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.
M&L for RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in Chajja complete all as specified and directed..
Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed
M&L for RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in slabs supported on walls etc. complete all as specified and directed.
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.
Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed.
Removing surplus excavated earth (soil) to a distance n. exc 50 m & depositing where directed at a level n. exc 1.5 m above the starting point complete all as specified and directed..
Removing excavated soil exceeding 250 metre but not exceeding 500 metre and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.
S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. .
Ditto all as per item No. 18 above, but 8mmdia and over upto and including 10mm dia in stirrups,spacer and binders.
M & L brick work with fly ash bricks straight or curved on planexc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.
M & L 40mm thick PCC 1:2:4 damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.
M&L for rendering 15mm thick in CM 1:4 on brick or concrete external surfaces, finishing even and smooth without using extra cement mixed with liquid water proofing compound as per Manufacturer's instructions complete all as specified and directed. ( Note : Liquid water proofing compound shall be measured and paid for separately)
M&L rendering 10mm th plaster in CM 1:6 on fair faces of brick or concrete surfaces(internal walls) finished even and smooth without using extra cement complete all as specified and as directed.
M&L for rendering 5mm thick in CM 1:3 on concrete surface of ceiling finishing even and smooth without using extra cement complete all as specified and directed.
M L for Moorum / Red bajri filling in floors or pavings, laid in layers n.exc15 cm thick spread, levelled and rammed including watering etc complete all as specified & directed.
M&L Hard core of gauge n.exc 63 mm, deposited, spread, levelled in layers not exc 15 cm thick, watered and well rammed to a true surface complete all as specified and directed..
M&L for Plain Cement Concrete (1:3:6) Type C2 using 40mm graded crushed stone aggregate, 75mm thick without using extra cement as in plinth protection complete all as specified and directed.
Forming contraction (dummy) joint 65mm deep X 10mm wide filled with sealing compoung Grade 'A', complete all as specified and directed.
M&L for 100mm thick Plain Cement Concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as sub base complete all as specified and directed.
M&L non skid coloured ceramic tiles 7 to 8 mm thick(square/rectangular) area of each tile exceeding 0.06 sqm but n.exc 0.11sqm in floor etc,over and including 15 mm thick screed bed in CM(1:6),set and jointed in neat cement slurry and pointed in white or coloured cement, to match with the shade of tiles complete all as specified and directed.
M&L for coloured glazed ceramic tiles in vertical surface 300x200x5to6mm thick over and including 10 mm thick cement plaster in CM (1:4); set and jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed
M&L three coats of white wash on new plastered ceiling surface including preparation of surfaces complete all as specified and directed.
M&L preparing newly plastered surfaces of wall or unplastered surfaces of wall and apply two coats of Cement base paint over a coat of appropriate primer complete all as specified and directed.
M&L for three coat of white washing on internal wall surfaces including preparation of surfaces complete all specified and as directed.
M&L rendering 10 mm thick in CM 1:3 , mixed with liquid water proofing compound, on concrete surfaces of roof , surface finished even and smooth complete all as specified and directed. ( Note : Liquid water proofing compound shall be measured and paid for seperately as "Supply only")
M&L for applying evenly tack coat of hot blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm after cleaning the surfaces over & including a coat of bitumen primer @ 0.30 litre/ sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil on the top of prepared roof surfaces complete all as specified & directed.
M&L for unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum side over lap of 100mm and end over lap of 150 mm shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls, special care shall be taken in laying APP modified water proofing membrane in situations such as drain/ expansion joints etc.
M&L for applying a coat of bituminous aluminium paint @ 100gm/ sqm over non-accessible roof and blinding material such as dry sand @ 0.75Kg/ Sqm over & including a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm over polymeric membrane complete all as specified & directed. Note- Bituminous aluminium paint shall be of same manufacturer as specified for polymeric water proofing membrane.
Supply only liquid water proofing compound (ISI marked) of approved Make complete all as specified & directed.
M & L Brick work with fly ash subclass 'B' bricks straight or curved on plan to any radius half brick thick wall built in CM 1:4 complete all as specified & directed.
S&F in repair Vitreous china bowl type Urinal flat back ,size 465x355x265 with grating and Union for discharg pipe including all necessary fittings complete all as specified and directed.
S&F for vitreous china squatting pan “Orissa” pattern, size 580 X 440 mm, white with integral foot rest,and "P" or "S" trap (excluding flushing cistern and flush pipe) but including connection to trap, and to flushing pipe, anti-syphonage pipe etc. complete all as specified and as directed.
S&F PVC low level flushing cistern (white) 10 Ltrs capacity with internal fitting, push button operated type with and including bracket, PVC flush pipe etc complete all as specified & directed.
S&F for vitrious china wash basin, white flat back size 550x400mm including waste, chain & plug andporeclain stopper and bracket etc. Complete including cutting for and pinning in ends of brackets or errecting bracket and 32mm dia waste fitting brass chromium plated for sink etc;with long screwed shanks and fly nuts,flange end bedded in red lead cement including 32mm dia waiste pipe fitted complete all as specified and directed.
Supply & fix 20 mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.
Supply & fix 25 mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.
S&F 15 mm fancy type pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts all as specified and directed .
S&F 15 mm fancy(concealed) type stop valve cast copper alloy chromium plated screwed high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 15 mm GI tube complete all as specified and directed .
S&F 20 mm fancy (concealed) type stop valve cast copper alloy chromium plated screwed high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 20 mm GI tube complete all as specified and directed .
S&F 15mm bore bib tap cast copper alloy chromium plated with crutch or butterfly handle fixed to 15 mm dia GI tube complete all as specified and directed.
S & F for Brass Chromium plated shower rose 125mm size, with or without swivel joints, any size, including fixing to steel pipe or union with Shower arm 15 mm size, 195mm long with bend of 45 degree with flange complete all as specified and directed.
Supply and fix 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.
S&F Ball valves high pressure of PTMT 20 mm dia with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed, complete all as specified & directed. (Minimum weight -210 gms)
S&F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to 20mm dia GI tube complete all as specified & directed.
Supply and fix 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls/ ceiling with & including necessary clamps of requird size etc complete all as specifed & directed.
Supply and fix 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls/ ceiling with & including necessary clamps of requird size etc complete all as specifed & directed.
S&F, in repair, grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gm) complete all as specified and directed.
S&F 75mm PVC (SWR) floor trap(S/P), plain with grating including jointing with solvent cement complete all as specified and directed.
M&L brass chromium plated tubular towel rail 20mm dia D type 600 mm long between flanges fixed complete all as specified and directed.
Supply and fix 110mm bore PVC (SWR) bends of any radius complete all as specified & directed.
Supply and fix 75mm bore PVC (SWR) bends of any radius complete all as specified & directed.
Supply and fix 110mm bore PVC (SWR) vent cowl complete all as specified & directed.
S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall pipe complete all as specified and directed.
S & F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed.
S&F PTMT waste coupling of 32mm dia for wash basin/urinal complete all as specified and directed.
S&F PTMT waste coupling of 40mm dia for wash basin/urinal complete all as specified and directed.
S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified & directed.
S & F Brass CP wall mixer(40 mm bore dia) formixing hot & cold water screwed down for iron pipe and fixed
S & F for Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified & directed.
S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet, reinforced with MS square tube, fixing in the opening complete as all as specified and directed.
S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top, bottom and side rails, MS frame shall be covered with heat molded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fixed in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement and fixing in the frame at site complete all as specified and directed.
S&F Sheet glass 3mm thick, ordinary quality frosted and glazing fixed with aluminium/ Steel section in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.
S&F Sheet glass 3mm thick, ordinary quality and glazing fixed with aluminium section in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.
S&F in repairs, galvanised steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed.
Supply and Fix aluminium handles 100mm size, cast type, anodised complete all as specified & directed.
Supply and fix 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.
Supply & fix 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.
Supply & fix 250mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.
S&F Pressed steel frames for doors, size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.
M & L PCC 1:3:6 type C-1 using 20mm graded stone aggregate for hold fast blocks, including necessary form work for rough finished surfaces etc complete all as specified and directed.
M&L for factory made 35mm thick second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, framed, panelled shutter (two or three panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stiles as per IS: 1003 (Part-I), kiln seasoned complete all as specified & directed. Note:- Butt hinge will be measured and paid for separately .
M&L for factory made second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all as specified & directed. Notes:- (i) glazing will be measured and paid for separately. (ii) Butt hinge will be measured and paid for separately .
M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat synthetic enamel paint of colour as approved by AGE(I) over and including a coat of pink primer complete all as specified & directed.
S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.
S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.
S&F factory made steel ventilators with top hung shutter including hinges,steel peg stay complete all as specified and directed.
S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe- 290 ( Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts). No claim whatso ever shall be entertained by Govt on this account.
S&F for Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.
M&L for preparation of new surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer as approved by AGE(I) complete all as specified & directed.
S&F in repair 20 mm dia decorative type curtain rod with rings and brackets complete and all as specified and directed
S&F 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and direcetd.
M & L machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid over & including 20 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including moulding, rubbing and mirror polishing, laid in floors or window cills complete all as specified and directed.
S&F framed work as in iron enclosure, doors or gate of angle iron or other section with gussets plate, rails, braces etc drilled for fixing of steel seating other covering, door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel handing door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account.
M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of distemper, oil emulsion, white or tinted, over one coat of appropriate primer complete all as specified and directed.
M & L for Roof tiles, Mangalore pattern,interlocking at side joints, laid in Roof etc, & Section of fillet n. exc. 25 sq cm and to any shape in cement mortar 1:3 including all mitres, stops, etc and cement screed base laid over & including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.
M& L for finishing new work on wall external surfaces with textured exterior paint of required shade, two or more coats applied @ 3.28 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/10 sqm complete all as specified and directed.
M & L for Granite (of any type) tiles 20mm thick, machine cut, in skirting/dado laid over cement screed and jointed with grey cement slurry and & pointed in white or coloured cement to match with the shade of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed.
M& L for bold metalic stainless steel letters or alphabets made with 2mm thick sheet , 25 mm wide and 10mm thick(hollow) fixed on wall tiles/ granite elevated from surface, letters of size 30 x 20 cm complete all as specified & directed.
Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.
Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.
Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.
M&L for 300mm dia Reinforced concrete pipes,class NP2, laid and jointed complete with collars complete all as specified and directed.
M&L for Hardcore of guage exceeding 63mm but n exc 100mm of broken stone aggregate, deposited,spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified and directed.
M&L for 150mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as sub base complete all as specified and directed.
Supply and fix machine pressed precast concrete interlocking paver block any shape and size with grey cement & pigment conforming to IS 15658-2006 of 60 mm thickness M-35 Grade over and including 50mm thick sand cushioning complete all as specified and as directed.
M&L for providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges, of cement concrete 1:2:4 type B-0 using 12.5 mm garded stone aggregate complete all as specified and directed.
M&L for PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.
M & L brick work with sub class B fly ash bricks, straight or curved on planexc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.
M&L for rendering 15mm thick in CM 1:4 on brick or concrete surface, finishing even and smooth without using extra cement complete all as specified and directed.
M & L PCC 1:2:4 types B-1 (using 20 mm graded crushed stone aggregate) as in coping including necessary formwork etc complete all as specified and as directed.
M&L for cement concrete in 1:3:6 type C2, using 40 mm graded stone agg as in surface channel and drain, complete all as specified and directed.
Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds,mitred/stopped ends etc. complete all as specified and directed.
Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.
Supply,laying & fixing Double Wall Corrugated (DWC) pipes made of High Density Polyethylene (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc.. complete all as specified and as directed , outer dia 175 mm and inner dia 147 mm complete all as specified and directed. ( Make :- Telerex/Tirupati or Eqivalent Make as approved by AGE)(I)
M&L for concrete bed to drain pipes in PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate including packing under, and haunching against the sides of pipe after they are laid and tested for 150mm bore of pipe complete all as specified and directed.
Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm internal dia of pipe complete all as specified and directed.
Point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 sqmm (nominal area), single core, flame retardant low smoke(FRLS), PVC insulated and unsheathed cable 1100 volts grade, ISI 694 marked TEC and FIA approved in and including PVC conduit concealed type and its fittings ISI marked, with mild steel sunken/Modular metal boxes suitable for modular/normal switch/sockets etc with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer internally, including covered with suitable module cover plate with frame including flame retardant low smoke (FRLS) PVC insulated unsheathed stranded copper conductor 1.5 sqmm (nominal are) single core cable as earth continuity conductor to common earth and connected to earth dolly complete all as specified for the followings :-
(a) One light point controlled by one switch 5 Amp
(b) One Fan point controlled by one switch 5 Amp
(c) One socket outlet 3 pin 5 Amp on independent board
(d) One socket outlet 3 pin 5 Amp on same board
All as per item No 118 above but using 4.0 Sqmm cable for one 15 A socket outlet point with 2.5 Sq mm PVC insulated, unsheathed copper conductor cable as earth continuity conductor.
S & F modular switch 1 way 6A 1 module complete all as specified and directed.
S & F modular socket 6A 2/3 Pin combined 2 module complete all as specified and directed.
S & F modular socket 6A/16A 2/3 Pin combined 2 module complete all as specified and directed.
S & F modular switch 1 way 16A 1 module complete all as specified and directed.
S & F modular Fan step regulator, 120W - 2 module complete all as specified and directed.
S & F White cover plate with frame with modular metal box, 1 module complete all as specified and directed.
S & F White cover plate with frame with modular metal box, 3 module complete all as specified and directed.
S & F White cover plate with frame with modular metal box, 4 module complete all as specified and directed.
S & F White cover plate with frame with modular metal box, 6 module complete all as specified and directed.
S & F for ceiling rose 3 phase/PVC/polycarbonated isolated body complete all as specified and directed.
S & F for Tele socket RJ 11 double without shutters (Make Anchor Model woods code No-60220 or equivalent in Wipro/Havells as approved by AGE(I)) complete all as specified and directed.
S & F rigid non metallic PVC conduit 20mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles pipe hooks etc complete all as specified and directed.
Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.
Supply and fix building security light of 35/36 watt, IP 66, LED die cast aluminium with LED street optic lenses ,efficacy of skyline plus is upto 120lm/w, with pea nut lenses LED type with bracket arrangement complete all as specified and directed. (Make - Wipro Cat No LR13-241-XXX-57-XX or equivalent in Philips/Oshram as approved by AGE(I))
Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.
S & F for lamp holder, PVC/Polycarbonate type with cord grip cap suitable for batten fittings with and including 12 Watt LED bulb retrofit type complete all as specified and directed.
Supply and fix, Single phase, ceiling fan 1200 mm sweep, permanent magnet Brushless Direct Current(BLDC) Motor 230 Volt, 50 Hz, 5 Star rated , 26-30 Watt, rated current 0.16 amp, pf 0.98, 370/360 rpm, minimum air delivery 210 CFM with service value greater than 6.00 BEE, number of blades three, type of blade leaf 1.05 mm thick aluminium sheet, remote control, radio frequency, 5 speed +off timer option speed regulation, class of insulation 'B' with two nos bearings including connecting wire from ceiling rose to fan terminal complete with all as required and directed at site by Engr -in charge
Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm including electric connection with PVC flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.
S & F for MCB DBs 12 Way SPN for mounting MCBs/RCBOs/ ELCBs etc. as per IS specification, factory made, fabricated out of CRCA sheet 1.2 mm thick, powder coated, fitted with DIN Channel neutral link and 200 Amps rated bus bar.The DB's shall double door type . Inner door fixed on spring loaded hinges with locking arrangement & outer door openable hinged with locking arrangement having IP-43 protection complete all as specified and as directed. .
All as per item No 139 above but 4 way SPN (for gate/post lights/security eqpt)
S & F for MCB/Isolator DP 40 Amps 240 Volts, 'B' Curve, 10 KA breaking capacity complete all as specified and as directed.
S & F for MCB/Isolator SP 6-32 Amps 240 Volts, 'B' Curve, 10 KA breaking capacity complete all as specified and as directed.
M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 6 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .
S & F flood lights 50W LED 6500K, with best in class design & robust heat sink along with class leading IP, IK & Surge protections complete with all clamps, Nuts & bolts as speicifed and directed. (Make : Havells Model- CENTURA NEO / or equivalent in Wipro/Bajaj/Phillips/ Crompton as approved by AGE(I))
S & F post top lantern 25W LED,IP 65, energy saving, environment friendly, long life, aesthetically designed with symmertical light distribution, spun aluminum landscape luminaire with high power including pole 300mm long, 76mm outer dia, for fixing the light complete all as specified and directed. (Make : Havells Model- CORAL (OPAL) or equivalent in Philips/Crompton Greaves/Bajaj/ Wipro as approved by AGE(I))
Earthing complete with galvanised steel earth plate electrode of size 60cm X 60cm X 6mm buried directly in ground (earth pit not less than 2.25 metres deep below the normal ground level) with top edge of the plate not less than 1.5m below normal GL connected to GI earth wire 4 mm dia by means of GI bolts, nuts, check nuts and washers and earth wire protected by 25 mm dia GI pipe medium grade and connected to main distribution board/earthing test point all as shown on electrical plate No.3 of SSR Part I and all as specified including testing on completion. (Notes: (a) The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 mix, Type C1, pit 40mm thick RCC 1:2:4 mix, type B1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe for earth lead upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II and also refer Plate No-03. Earth wire and protection pipe beyond 7.5m shall be measured and paid separately. (b) Earthing will be redone if desired earth result not found during testing of the same at site.)
Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 16sqmm, 2core including jointing materials such as cable glands & lugs etc Complete all as directed. ( Note : Excavation and earth work, sand cushioning and cable protection will be measured and paid for separately.)
Supplying and fixing Galvanised mild steel pipe /tubing, of size 40 mm bore dia, light grade complete with all fittings, laid in trenches/under roads, drain, paths, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers complete all as specified and as directed.
Supply and laying Sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed . ( Note : Punned thickness shall be measured for payment)
Supply and laying Brick covering with width equal to length of brick as mechanical protection to cable with well burnt sub class ‘B’ fly ash bricks, laid dry, flat complete all as specified and directed .
Cutting existing steel tubing for alterations or additions ( Each cut measured) done in position without taking down , bore of pipe 40mm or 50mm, complete all as specified and directed .
S & F Tubes, 'medium grade' galvanised, with all fitting and fixed complete, laid in trenches, 25mm dia complete all as specified and directed.
S& F Gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed in 25mm dia GI pipe complete all as specified and directed.
Schedule of credit amount of Rs. 22,800.00 to be deducted during AOC
sanjay enterprises
M/S INDIA ENTERPRISES
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .