Development of Park adjoining Barat Ghar (Chanchal Park) at village Bakkarwala in Distt. West.

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Supply of earth at site including excavation royalty of earth carriage by mechanical transport including loading, unloading and banking the same in layers not exceeding 20cm in deptt, breaking clods rolling each layer with ½ tonne roller of wooden of steel rammers and dressing up in embankment for road, flood banks, marginal banks and guide banks or filling up ground depressions with a lead of 5.00 Km. and lifts 1.5 m./loose soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering,shuttering and finishing : 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) Red sand stone - Exposed face fine dressed with rough backing 30 mm thick

12 mm cement plaster finished with a floating coat of neat cement of mix 1:4 (1 cement: 4 fine sand)

Supply of Precast reinforced cement concrete Bench ( Chair type bench with hand rest). The bench consist of 2 Nos. L- shape base support in cement co lour of thickness 80 mm back height 890 mm and front height 450 mm base width 690 mm as per sketch and 1 No reinforced concrete plank in the red colour of size 1500x320x50 mm and 1 No. of reinforced concrete plank in red colour of size 1500x425x50 mm . Manufactured by using M- 30 grade of concrete and reinforced suitably to prevent damage during handling, transportation, erection and long use. All parts are joined together with galvanized nuts and bolts of suitable size. All bolts are to be sealed after assembly. Seating length of the bench 1500 mm and seating height of the bench 450 mm. Total height of the bench 890 mm Bench top and back planks are treated with special anti corrosive water proof coating so as to make surfaces glossy and water proof.

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in- Charge. 60mm thick Cement concrete paver block of M-35 grade with approved colour, design & pattern

Providing and laying cement concrete pavement of M-10 with ready mixed concrete from batching plant of reputed cement manufacture and transported to the site of work in transit mixer having continuous agitated mixer, manufacture as per mixed design of M-10 grade of cement concrete work including pumping of RMC from transit mixer to site. Placing in required camber compulsory with plate/screed vibrator with wire brush etc. and curing including cost admixer in recommended proportions as per IS:9103 to accelerate/retard setting of concrete, improve workabilty witthout impairing strength and durabiltity as per specification and direction of Engineer-in-Charge. Note-1) Excess/less cement used than specified in this item is payable/recoverable seprately.M-10 Grade plain cement concrete by using 220 kg of cement per cum of concrete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 15m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1½:3 (1 Cement: 1½ coarse sand: 3 graded stone aggregate 20 mm nominal size).

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness Make Elliptical Cross Trainer: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. An internal limiter is fitted inside to prevent the equipment from moving uncontrollably. The Foot restand Base plate covers are manufactured from Virgin LLDPE. Bearings : Maintenance-free ball bearings. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 1100x550×1510mm . Capacity 1 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness. Make Health Walker: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. An internal Limiter is fitted inside to prevent the equipment from moving uncontrollably.The Foot rest and Base plate covers are manufactured from Virgin LLDPE. Bearings : Maintenance-free ball bearings. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H)1064×520×1250mm . Capacity 1 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam FitnessMake SIT UP: The products must tested and certified to meet EN16630 safety standards with GS test mark.The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. The Seat and Base plate cover are manufactured from Virgin LLDPE. Bearings : Maintenance-free ball bearings. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 1480×1200×630mm . Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam FitnessMake Rider: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. The Seat and Base plate cover is manufactured from Virgin LLDPE. Bearings : Maintenance-free ball bearings. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 1263×558×1267mm . Capacity 1 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make TAI CHI spinners: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. Bearings : Maintenance-free ball bearings. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H)1245×1070×1500mm . Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make Pulldown Challenger: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. An internal Limiter is fitted inside to prevent the equipment from moving uncontrollably. Bearings : Maintenance-free ball bearings. The Seat, backrest and Base plate cover are manufactured from Virgin LLDPE. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 2310×700×1880mm . Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make Seated Chest Press: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. An internal Limiter is fitted inside to prevent the equipment from moving uncontrollably. Bearings : Maintenance-free ball bearings. The Seat, backrest and Base plate cover are manufactured from Virgin LLDPE. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 1800×698×1880mm. Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make MINI SKI: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. An internal Limiter is fitted inside to prevent the equipment from moving uncontrollably. Bearings : Maintenance-free ball bearings. The Foot rest and Base plate cover are manufactured from Virgin LLDPE. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 1050×784×1400mm. Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make BICYCLE: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. Bearings : Maintenance-free ball bearings. The Seat and Base plate cover are manufactured from Virgin LLDPE. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 853×490×1305mm Capacity 1 person.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make SELF WEIGHTED ROWER: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. An internal Limiter is fitted inside to prevent the equipment from moving uncontrollably. Bearings : Maintenance-free ball bearings. The Seat, backrest and Base plate cover are manufactured from Virgin LLDPE. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 1260×800×920mm. Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make Squat Pusher: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. An internal Limiter is fitted inside to prevent the equipment from moving uncontrollably. Bearings : Maintenance-free ball bearings. The Seat, backrest and Base plate cover are manufactured from Virgin LLDPE. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 1800×698×1884mm. Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make WAIST TWISTER: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. An internal Limiter is fitted inside to prevent the equipment from moving uncontrollably. Bearings : Maintenance-free ball bearings. The Base plate cover is manufactured from Virgin LLDPE. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) Ø1400×1350mm.Capacity 3 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness Make DOUBLE AIR SKIER:The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. Bearings : Maintenance-free ball bearings. The Foot rest and Base plate cover are manufactured from Virgin LLDPE. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain as per the maintenance guide. Size (L*W * H) 1610×500×1500mm Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make BIG SHOULDER WHEEL: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. Bearings : Maintenance-free ball bearings. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H)870×767×1940mm . Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make PUSH UP AND DIP STATION: The products must tested and certified to meet EN16630 safety standards with GS test mark.The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. Bearings : Maintenance-free ball bearings. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain as per the maintenance guide. Size (L*W * H)1800×630×1600mm . Capacity 2 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make Leg Extension: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. Bearings : Maintenance-free ball bearings. The Seat, backrest and Base plate cover are manufactured from Virgin LLDPE. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain as per maintenance guide. Size (L*W * H) 713x620x970mm . Capacity 1 persons.All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make Balance Beam: The products must tested and certified to meet EN16630 safety standards with GS test mark. The structural post of diameter 114mm and 2.5mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. ALL Other external metal components of diameters dia28/32/38/60 and thickness of 2.0mm thickness are hot dipped galvanized and baked varnish with rosin under high temperature. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using ALESTA - USA Powder Coatings to the thickness of 130 - 180 microns. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L* W * H) 3000 x 300 x 250mm. Capacity 1 persons. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & fixing of Arihant /Kompon /Landscape /Koochie /Hugo / Grandslam Fitness make Arm and pedal bike. The products must tested and certified to meet EN16630 safety standards with GS test mark. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped. Joints are Robotic Welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharp edges & burrs. Zinc Primer paint is applied at all the welding paints prior to finishing. All metal parts are powder coated using AKZO Nobel - Great Wall Powder to the thickness of 80 – 120 microns. All metal parts are tested in a 5% NaCL solution in accordance to ISO7227 to speed up corrosion for 3000 hrs. The seat is made from Rotomoulded LLDPE. Bearings : Maintenance-free ball bearings. Scope of delivery : 1 completely pre-assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Size (L*W * H) 830 MM x 500 MM x 1450 MM . Capacity 1 person. A cycling and upper arm exercise rolled into one. Co-ordination between leg and arm movement encourages balance whilst exercising too. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Providing and fixing 36mm thick EPDM (Ethylene Propylene Deine Monomer) Rubber flooring on existing surface in required color and shape. The EPDM Rubber flooring should be laid at site in dual color and pattern as per the direction of the Engineer-in-charge. All complete fixing of equipment in foundation is to done as per manufacturer specification.

Supply and fixing of 1.8 MTR Wave Slide HPS-SAL-747:“A” shaped support posts of height 2.28 m, are to be schedule Galvanized steel with a 60mm OD {Outer Diameter}.All the posts are to be finished with a baked on powder coat finish. Powder coatings used TGIC Polyester powder. Electro - statically applied polyester powder must have a tough finish with maximum durability. Deck of size 0.80 m x 0.60 m and Staircase of size 1.84 m x 0.60 m shall be an all-PATENT welded assembly fabricated from perforated solid punched steel. Deck perimeter is precision pre punched for attachments. Decks are pre pressed, punched, and welded, powder coated to 2.2mm thickness or vinyl plastic coated to a thickness of 4mm [optional].Handrail of height 1.9 m and Dia 32 mm shall be an all-patent welded unit, fabricated from 32 O.D. galvanized steel pipes with a baked on powder coating finish.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well.Wavey Slide of size 2.95 m x 0.72 m x 1.72 m, Panels, Plastic Components [super thick plastic] shall be rotationally molded from antistatic, copolymer.ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS.PLAY EQUIPMENT DIMENSIONS: Size: L x W x H 4.18 m x 0.89 m x 2.28 m. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply and fixing of 4 Seater See saw HPS-SAL-704: The See Saw consists of 2 poles of Dia 114mm and thickness of 2.5mm which balances the horizontal rod at the center which is of size 1614 mm length and Dia 114 mm. It consists of 4 seats which is made of LLDPE virgin plastic of size 364 mm X 250 mm X 180 mm.Each seat consists of a safety stand in the horizontal balance bar which is of 500 mm X 462 mm and a thickness of Dia 32 mm.Specialized connectors such as clamps and couplings are to be cast from aluminum which is pretreated, and cured, with a baked on powder coat finish.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS. Size:( L x W x H ) 2.60 m x 0.5 m x 0.7 m All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply and fixing of 2 Seater See saw HPS-SAL-706: The See Saw consists of 2 poles of Dia 114mm and thickness of 2.5mm which balances the horizontal rod at the center which is of size 1614 mm length and Dia 114 mm. It consists of 2 seats which is made of LLDPE virgin plastic of size 363 mm X 250 mm X 155 mm.Each seat consists of a safety stand in the horizontal balance bar which is of 500 mm X 462 mm and a thickness of Dia 32 mm.Specialized connectors such as clamps and couplings are to be cast from aluminum which is pretreated, and cured, with a baked on powder coat finish.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS. Size:( L x W x H 1.91 m x 0.5 m x 0.82 m All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply & Fixing of Multiplay System HPS-MPS-506: Upright structural posts of height 2.3 m, 2.6 mand 3.2 m are to be schedule Galvanized steel with a 114 mm OD. All the posts are to be finished with a baked on powder coat finish. Powder coatings used TGIC Polyester powder. Electro -statically applied polyester powder musthave a tough finish with maximum durability. The pre treatment and curing process includes Acid wash > freshwater rinse > iron phosphate rinse > final rinse > rust prevention treatment >seal & dry-off > oven baked electro-static powder application and dual zone curing in the oven > QC Controls > Final finish. Finished products have the following typical characteristics: 0.5mm thickness, oven cured between 191oCand 220oC, to achieve Flexibility, Impact, Salt Spray {Corrosion} Resistance, Hardness, and Adhesion. Specialized connectors such as clamps and couplings are to be cast from aluminum which is pretreated, and cured, with a baked on powder coat finish. Deck of size 1.16 mx 1.16 m and Staircase of size 1.0 m x 0.60m shall be an all-PATENT welded assembly fabricated from perforated solid punched steel. Handrail of height 1.88m and Dia 32 mm shall be an all-patent welded unit, fabricated from 32 O.D. galvanized steel pipes with a baked on powder coating finish. Snake Climber, Piped walls of size 2.14 m shall be an all patent welded fabricated from 32 O.D. galvanized steel pipes for the outer pipes and 25 mm O.D. galvanized steel for the inner parallel bars with a baked on powder coat finish. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304. Roof of size 1.47 m x 1.47 m x 0.96 m, WaveySlide of size 2.38m x 0.55m x 1.20m, Panels, Plastic Components [super thick plastic] shall be rotationally molded from antistatic, copolymer, virgin linear low density UV stabilized polyethylene, with “color molded” in not “added in”. Top rails Of Monkey Bar of size 2.32m x 1.0mand Swing of size 2.55 m x 1.16m shall be fabricated from 32mm O.D. galvanized steel pipe with a baked on powder coating finish. Finished products have the following typical characteristics: 0.5mm thickness, oven cured between 191oC and 220oC, flexibility, Impact, Salt Spray resistance, Hardness, and Adhesion. Play Equipment Dimensions : 7.44 m x 4.03 m x 3.81 m All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply and Fixing of Hexa Climber HPS-SAL-708: -Upright structural posts of height 2.3 m, are to be schedule Galvanized steel with a 114 mm OD {Outer Diameter}. All the posts are to be finished with a baked on powder coat finish. Powder coatings used TGIC Polyester powder. Electro -statically applied polyester powder musthave a tough finish with maximum durability. The pre treatment and curing process includes Acid wash > freshwater rinse > iron phosphate rinse > final rinse > rust prevention treatment >seal & dry-off > oven baked electro-static powder application and dual zone curing in the oven > QC Controls > Final finish. Finished products have the following typical characteristics: 0.5 mm thickness, oven cured between 191Oc and 220oC, to achieve Flexibility, Impact, Salt Spray {Corrosion} Resistance, Hardness, and Adhesion. Specialized connectors such as clamps and couplings are to be cast from aluminum which is pre treated, and cured, with a baked on powder coat finish. Parallel Climber of size 1.9 m x 1.17 m , Horizontal Ladder 1.9 m x 1.17m, Pull up Bar, Chain climber of size 1.9 m x 1.17 m, and Gymnastic Rings of size 0.77 m x 1.17 m shall be an all patent welded fabricated from 54 mm O.D. galvanized steel pipes with a baked on powder coat finish. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. PLAY EQUIPMENT DIMENSIONS: 2.2m x 2.1m x 2.3m All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply and Fixing of Merry Go Round HPS-SAL-748: The platform Dia.1.21m, of thickness 2mm and width of 60 mm, with solid precision punched holes and reinforcement rib. After shot blasting, oil and phosphate removal, Zinc Primer Paint is applied at all the welding points using Zinc powder (Interpon PZ660) and Powder coated using Akzo Nobel powder coating.The handrails is made from Dia. 50 mm galvanized steel tubes and wall thickness of 2mm as per GB / T 700-1988. The welding used is CO2 shielded arc welding (meets with the requirement of BS1387-1985, and the technology used meets the requirement of the BS1387-1985) and welding is done by robotic welding. The Centre rod for the merry go round is made from 98mm dia, galvanized steel post and connected on to a 160mm dia pipe which is connected to the base plate at the bottom for fixing the foundation. The concealed bearings of grade 6213 and 32213 which conforms to GB-T308-2002 is used to ensure smooth movement of the equipment. The centre rod is connected to the 1.3m dia platform througha base plate of 250mm dia using M16 stainless steel anti theft screws. The installation requires the poles to be fitted using Anchor fasteners on a concrete foundation of minimum strength M-25, cement concrete blocks of required size,as per direction given by engineer incharge, finished below ground level. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Supply and Fixing of Monkey Bar HPS-SAL-711: Support posts of height 2.1 m are to be schedule Galvanized steel with a 89 mm OD {Outer Diameter}.All the posts are to be finished with a baked on powder coat finish. Specialized connectors such as clamps and couplings are to be cast from aluminum which is pretreated, and cured, with a baked on powder coat finish..Handrail of size 0.94 m and Dia 32 mm shall be an all-patent welded unit, fabricated from 32 O.D. galvanized steel pipes with a baked on powder coating finish.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. .ALL WELDING IS CARRIED OUT BY ROBOTS [SIMMILIAR TO THE ONES USED IN THE AUTOMOBILE INDUSTRY], WHICH GUARANTEES STRONG AND SMOOTH WELDS ELIMINATING ANY RAG, WELD SCARS AND ENSURES THE INTEGRITY AND STRENGTH OF THE WELDED AREAS. Size:( L x W x H)2.91 m x 1.11 m x 2.2 m. All complete as per the direction of engineer in charge or as per approved drawing & design given by manufacturer including earth work, c:c work up to plinth level, c:c block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) of required size as per department / manufacturers specifications and guidelines.

Jai Durga Construction Company

VINOD KUMAR AND CO

sunrise construction company

ASHOK BUILDERS

GOPAL CONSTRUCTION COMPANY

SUSHIL KUMAR JAIN

S P CONSTRUCTION COMPANY

DC Engineers

Ajay Kumar Singhal

Buildex Infratech

I K CHOUDHARY

KHATRI CONSTRUCTION COMPANY

S N MALHOTRA & SONS

V K Construction Co

M.S. CONSTRUCTION CO.

C P Singh

M/S SHARVAN CONSTRUCTION CO.