CONSTRUCTION OF UPGRADED 50 BEDDED SUB

Amount

Item No.1 :- Excavation for foundation in earth, soils of all types, sand gravel and soft murum including removing the excavated materials upto a distance of 50 meters beyond the building area including all leads and lifts upto 1.5 metre, stacking and spreading as directed including dewatering, unless provided elsewhere preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete.

Item No.2 :- Excavation for foundation in laterite rock (soft or hard) including trimming and levelling the bed for the foundation, removing the excavated material up to a distance of 50 metres beyond the building area, stacking as directed, dewatering and back filling with available murum, watering, ramming etc. complete. (Lift upto 1.5 m.).

Item No.3 :- Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift upto 1.5 metre).

Item No.4 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No.5 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Item No.6 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) treatment by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrifos per square metre of vertical surface area covering 10 years guarantee on bond paper.

Item No.7 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper.

Item No.8 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30-60 cm. deep at 15 cm. c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper.

Item No.9 :- Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No.10 :- Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

{ B } For First floor

{ C } For Second floor

Item No.11 :- Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

{ B } For First floor

{ C } For Second floor

Item No.12 :- Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

{ B } For First floor

{ C } For Second floor

Item No.13 :- Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

{ B } For First floor

Item No.14 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap metal for R.C.C. pardi of required thickness including centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

{ B } For First floor

Item No.15 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

{ B } For First floor

{ C } For Second floor

Item No.16 :- Providing and fixing during laying in RCC Slab rectangular 2 millimeter thick M.S. sheet fan hook box of size 180 x100 millimeter with required depth with holes or notches as required, bottom and top sides of 1.6 millimeter M.S. sheet fixed with 3.5 millimeter diameter round headed screws together with 12 millimeter diameter M.S. bar bent to shape with hooked ends for fan hook and painting to exposed surface etc. complete. ( Ground Floor )

{ B } For First floor

Item No.17 :- Providing and fixing in position TMT (Thermo Mechanically Treated) FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (For Ground Floor)

{ B } For First floor

{ C } For Second floor

Item No.18 :- Filling in plinth and floors with contractor's murum in 15 to 20 centimeter layers including watering and compaction as directed by Engineer-in-charge with all leads and lifts etc. complete.

Item No.19 :- Filling in plinth and floors with approved excavated materials in 15 to 20 centimeter layers including watering and compaction as directed by Engineer-in-charge with all leads and lifts etc. complete.

Item No.20 :- Providing dry trap rubble stone soling 15 centimeter to 20 centimeter thick including hand packing and compacting etc. complete.

Item No.21 :- Providing laterite stone masonary in cement mortar 1:6 in foundation and plinth including striking joints on the unexposed faces and watering complete.

Item No.22 :- Providing and constructing laterite stone masonry in cement mortar 1:6 in superstructure including raking out joints where plastering is to be done watering , scaffolding with all leads and lifts etc. complete. (Laterite stone 6 sides cut and thickness of morter joints shall be 12 millimeter miximum) ( Ground Floor )

{ B } For First floor

Item No.23 :- Providing Autoclaved Aerated Concrete Block masonry of Ecolite or equivalent make conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) ( Ground Floor )

{ B } For First floor

Item No.24 :- Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. on cement mortar 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete. ( Ground Floor )

{ B } For First floor

Item No.25 :- Providing and fixing in position Double shuttered aluminium extruded powder coated openable door of specified size with aluminium door frame of powder coated section 101.60 x 44.75 millimetre, 3.18 millimetre thick and shutter comprising of powder coated section having bottom and lock rail of size 150 millimetre x 44.5 millimetre x 3.00 millimetre thick top rails 47.62 x 44.45 millimetre x 3.00 millimetre thick , vertical style 47.62 x 44.45 millimetre, 3.00 millimetre thick and for shutter plain glass panes 5 millimetre thick for top panels and 12 millimetre thick both side laminated phenol bonded particle board panels for bottom panels etc., I.S.I. mark, heavy duty, Hydraulic floor spring of 150 kilogram capacity , having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250 millimetre length aluminium tower bolts, 150 millimetre diameter pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials, labours, and equipment etc. complete. ( Ground Floor )

{ B } For First floor

Item No.26 :- Providing and fixing solid core flush door shutter in single leaf 32 millimeter thick decorative type of exterior grade as per detailed drawings approved face veneers 3 millimeter thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. ( For Ground Floor )

{ B } For First floor

Item No.27 :- Providing and fixing fiber glass reinforced polyster door shutter 30 millimetre thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc. complete. ( Ground Floor )

{ B } For First floor

Item No.28 :- Supplying and fixing in position Aluminium extruded section Four track sliding windows upto 1.2 metre height, outer frame made from section of over all size 80 millimetre x 45 millimetre, bottom section with or without drain section, track weighing 0.90 kilogram per metre and top and side section weighing 0.838 kilogram per running metre with shutter or sections made of 19 millimetre x 40 millimetre size having average weight of 0.6 kilogram per running metre (or as required size) with change in proportionate weight fixed with 5 millimetre thick High performance Single Glaze Unit (SGU) - Glass, new neoprene gasket shutters to be provided with nylon encased stainless rollers, necessary locks and handles complete. , and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. ( Ground Floor )

{ B } For First floor

Item No.29 :- Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 millimetre at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 millimetre at weight 1.070 kg/Rmt. Top and side track section 92 x 31.75 x 1.30 millimetre at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 millimetre at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 millimetre thick High performance Single Glaze Unit (SGU) - Glass , and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising without box. ( Ground Floor )

{ B } For First floor

Item No.30 :- Providing and fixing in position anodised (as per IS 1868/1982) Aluminium fixed staggered ( Z Type ) Ventilator with aluminium rectangular pipe 63 mm x 38.10 millimetre x 1.22 millimetre at weight 0.650 Kg/Rmt, Aluminium angle of size 15 millimetre x 15 millimetre x 1 millimetre, aluminium channel of 9 millimetre sizes, S. S. mosquito net of 304 Grade, 4 millimetre thick float glass per detailed drawing and as directed by Engineer in charge etc. complete. ( Ground Floor )

{ B } For First floor

Item No.31 :- Providing and fixing in position aluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineerincharge with all necessary alluminium sections including necessary fixtures and fastening such as 5 mm thick clear float glass etc. complete. With powder coating ( Ground Floor )

{ B } For First floor

Item No.32 :- Providing and fixing mild steel grill work for windows, ventilators etc. 20 kilogram per square metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. ( Ground Floor )

{ B } For First floor

Item No.33 :- Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 millimetre x 1.22 millimetre box type, 5 millimetre thick sheet glass louvers, of approved quality etc. complete. ( Ground Floor )

{ B } For First floor

Item No.34 :- Providing internal cement plaster 6 milimeter thick in single coat in cement mortar 1:4 with neeru finish to concrete surface in all position including scaffolding and curing etc. with all leads and lifts etc. complete. ( Ground Floor )

{ B } For First floor

Item No.35 :- Providing internal cement plaster 12 millimeter thick in single coat in cement mortar 1:4 with neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. ( Ground Floor )

{ B } For First floor

Item No.36 :- Providing internal cement plaster 20 milimeter thick in a two coat in cement mortar 1:4 with neeru finish to concrete, brick surface in all positions including scaffolding and curing with all leads and lifts etc. complete. ( Ground Floor )

{ B } For First floor

Item No.37 :- Providing and applying Texture plaster with finishing with Purlina/ Rustic texture material (with texture material of Asian/ Renava/ Nitco/ Temtex or equivalant company make) in 3 to 4 millimeter thickness on previously finished plastered surface including plaster Groove 6 millimeter thick or Tape Grooves 35 to 45 millimeter thickness or as required in all postion including preparing the surface scaffolding etc. complete. ( including texture Paint and Texture Paint Finishing) ( Ground Floor )

{ B } For First floor

Item No.38 :- Providing internal cement plaster 20 milimeter thick in single coat in cement mortar 1:3 without neeru finish to stone masonry surface in all positions including scaffolding and curing with all leads and lifts etc. complete. ( Ground Floor )

{ B } For First floor

Item No.39 :- Providing internal cement plaster 20 milimeter thick in two coats in cement mortar 1:5 without neeru finish to concrete, brick surface in all positions including scaffolding and curing with all leads and lifts etc. complete.

Item No.40 :- Providing fine cement finish 1.5 millimetre thick over green plaster surface including scaffolding curing etc. complete.

Item No.41 :- Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 to 605 millimetre x 590 to 605 millimetre of 8 to 10 millimetre thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. ( Ground Floor )

{ B } For First floor

Item No.42 :- Providing and laying vitrified mirror / glossy finish tiles having size 590 to 605 millimetre x 590 to 605 millimetre of 8 to 10 millimetre thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for skirting in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curign and cleaning etc. complete. ( Ground Floor )

{ B } For First floor

Item No.43 :- Providing and laying 18 millimetre thick ADONI BROWN LEATHER FINISH stone for flooring, machine cut in required size, approved shade, colour and texture laid using white cement slurry over 20 millimetre (average) thick base of cement mortar 1:4 followed by laying, fixing and jointed with white cement slurry mixed with matching pigment, including rubbing and curing moulding and polishing to edge to give high gloss finish etc. complete. The application rate for tile adhesives shall be as per manufacturer's recommendations. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels and as directed by Engineer in charge etc. complete. ( Ground Floor )

{ B } For First floor

Item No.44 :- Providing and laying 18 millimetre thick ADONI BROWN LEATHER FINISH stone for skirting, machine cut in required size, approved shade, colour and texture laid using white cement slurry over 20 millimetre (average) thick base of cement mortar 1:4 followed by laying, fixing and jointed with white cement slurry mixed with matching pigment, including rubbing and curing moulding and polishing to edge to give high gloss finish etc. complete. The application rate for tile adhesives shall be as per manufacturer's recommendations. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels and as directed by Engineer in charge etc. complete. ( Ground Floor )

{ B } For First floor

Item No.45 :- Providing and laying ceramic tiles of having size 30 centimetre x 30 centimetre confirming to I.S.15622/2006 (group D II-A) and 7 to 8 millimetre thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/colour cement slurry cleaning curing etc. complete. ( Ground Floor )

{ B } For First floor

Item No.46 :- Providing and laying ceramic tiles of having size 30 centimeter x 30 centimeter and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. ( Ground Floor )

{ B } For First floor

Item No.47 :- Providing and laying vitrified stone effect finish tiles having size 590 to 605 millimetre x 590 to 605 millimetre of 8 to 10 millimetre thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. ( Ground Floor )

{ B } For First floor

Item No.48 :- Providing and laying Antiskid Ceramic tiles of approved quality of size 30 centimetre x 30 centimetre and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. ( Ground Floor )

{ B } For First floor

Item No.49 :- Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength,thickness and size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 millimetre thick compacted bed of fine aggregate (natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocks into the fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer specifications and direction of Engineer-in-Charge. 60 millimetre thick Cement Concrete paver block of M-35 grade concrete with approved colour and design and pattern.

Item No.50 :- Providing and fixing on walls/ ceiling/ floor 15 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. ( Ground Floor )

{ B } For First floor

Item No.51 :- Providing and fixing on walls/ ceiling/ floor 20 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.52 :- Providing and fixing on walls/ ceiling/ floor 25 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.53 :- Providing and fixing on walls/ ceiling/ floor 32 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.54 :- Providing and fixing on walls/ ceiling/ floor 50 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete.

Item No.55 :- Providing and fixing screw down for 15 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete. ( Ground Floor )

{ B } For First floor

Item No.56 :- Providing and fixing Chromium Plated 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge. ( Ground Floor )

{ B } For First floor

Item No.57 :- Providing and fixing screw down for 32 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete.

Item No.58 :- Providing and fixing screw down for 50 millimetre diameter wheeled stop tap of brass including necessary sockets/union nut complete.

Item No.59 :- Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195 millimetre size with pillar cock, Chromium Plated Angular stop cock, long thread of approved make continental including Stainless Steel bottle trap of necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 millimetre thick fixed on Black Kadappa Framework, etc. complete. ( Ground Floor )

{ B } For First floor

Item No.60 :- Providing and fixing Jaquar or equivalent make wall hung white wash basin of size 470 x 575 x 190 millimetre - code no. OPSWHT-15801, with Jaquar or equivalent make half pedestal, code no. OPS-WHT-15305 with Jaquar or equivalent make pillar cock, code no. CON-021KN / 021KN G / 021KN GA / 021KN GB / 021KN GD, C. P. Angular stop cock long thread jaquar or equivalent make continental (Cat.No. CON-059) including Stainless Steel bottle trap of jaquar or equivalent make having code no. ESS-773 NB and necessary pipe connection up to the outside face of the wall etc. complete. ( Ground Floor )

{ B } For First floor

Item No.61 :- Providing and fixing white glazed earthenware sink 600 millimetre x 200 millimetre x 450 millimetre including all connection of the galvanised iron supply and Poly Vinyl Chloride waste pipes up to the outside face of the wall, cold water chromium plated screw down bib tap, rolled steel or Cast Iron brackets, rubber plug with chain and stop tap complete. ( Ground Floor )

{ B } For First floor

Item No.62 :- Providing and fixing sink cock with regular swinging spout ( Wall Mounted Model ) with wall flange with approved make incluidng other necessary fitting, etc. complete as directed by Engineer in charge. ( Ground Floor )

{ B } For First floor

Item No.63 :- Providing and fixing 10 centimeter Poly Vinyl Chloride nahani trap with grating etc. complete. ( Ground Floor )

{ B } For First floor

Item No.66 :- Providing, constructing and fixing Supreme make or equivalent make Ultra 250 millimetre diametre Inspection chamber made up of UPVC material of thickness 3.5 millimetre and height of 259 millimetre with inlet and outlet of 110 millimetre diametre with 75 millimetre diametre U Trap, Ultra shaft pipe of Upvc material having height of 470 millimetre and fixing Ultra 250 millimetre diametre UPVC cover and frame in 150 millimetre thick in cement concrete1:2:4, having crushed sand bed of 100 millimetre thick of size 550 millimetre diametre. Including excavation and refilling the sides of chamber by crushed sand cushioning 150 millimetre thickness, connecting all required UPVC fittings with rubber lubricant etc. complete.

Item No.67 :- Providing , constructing and fixing Supreme make or equivalent make Ultra 450 milimetre diametre Inspection chamber made up of Polypropylene / polyethylene material of thickness 3.5 millimetre and height of 388 millimetre with 160 or 200 millimetre main inlet (s) outlet and 110 and / or 160 millimetre branch inlets, with 450 millimetre diametre Ultra shaft pipe of HDPE material having height of 460 millimetre, having Reinforced Cement Concrete cover and frame fixing in 150 millimetre thick in cement concrete 1:2:4, having crushed sand bed of 150 millimetre thick of size 750 millimetre diametre. Including excavation and refilling the sides of chamber by sand crushed cushioning 150 millimetre thickness, connecting all required UPVC fittings with rubber lubricant etc. complete.

Item No.68 :- Providing , constructing and fixing Supreme make or equivalent make Ultra 600 milimetre diametre Inspection chamber Providing , constructing and fixing Supreme make or equivalent make Ultra 600 milimetre diametre Inspection chamber made up of Polypropylene / polyethylene material Having 315 millimetre diameter inlet(s)/outlets and with eccentric reducers as per requirement to connect 160 millimetre and 200 millimetre pipes having thickness of 5 millimetre and 600 millimetre in height, with inbuilt shaft achieve the invert depth as per site condition of wall thickness of 5 millimetre having Reinforced Cement Concrete cover and frame fixing in 150 millimetre thick in cement concrete 1:2:4, having crushed sand bed of 150 millimetre thick of size 750 millimetre diametre. Including excavation and refilling the sides of chamber by sand crushed cushioning 150 millimetre thickness, connecting all required UPVC fittings with rubber lubricant etc. complete.

Item No.69 :- Providing soak pit of size 120 centimeter x 120 centimeter x 120 centimeter including excavating and filling with brick-bats etc. complete.

Item No.70 :- Providing and fixing 450 millimeter x 550 millimeter size superior type Belgium mirror with 16 millimeter diameter nickel plated towel rod etc. complete. ( Ground Floor )

{ B } For First floor

Item No.71 :- Providing and fixing chromium plated towel rod 16 millimeter diameter and 75 centimeter in length including all accessories complete. ( Ground Floor ) (for toilets)

{ B } For First floor

Item No.72 :- Providing and fixing machine cut mirror polished 18 millimetre to 20 millimetre thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with rounding / moulding the edges etc. complete. Both side polish. ( Ground Floor )

{ B } For First floor

Item No.73 :- Providing and fixing H.D.P. container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres.

Item No.74 :- Providing and fixing P.V.C. Rain water pipes of 160 millimeter outer diameter and having wall thickness of 2.2 to 2.7 millimeter confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (The contractor shall give 3 yrs guarantee bond for payment) ( BRAND FINOLEX / SUPERME / PRINCE) ( For Ground Floor )

{ B } For First floor

Item No.75 :- Providing and fixing 75 millimeter diameter stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. ( BRAND FINOLEX / SUPERME / PRINCE) ( Ground Floor )

{ B } For First floor

Item No.76 :- Providing and fixing 100 millimeter diameter stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. ( BRAND FINOLEX / SUPERME / PRINCE) ( Ground Floor )

{ B } For First floor

Item No.77 :- Providing and fixing white European type wall-hung, of size 360 mm. x 360 mm x 575 mm with approved make flush valve including soil pipe, vent pipe upto outside face of wall, 100 millimetre diametre Cast Iron plug bend inlet pipe all fittings, cutting and making good walls, floors etc. complete. ( Ground Floor )

{ B } For First floor

Item No.78 :- Providing and fixing Orissa Pan of size 580 x 445 x 260 millimetre with approved make flush valve including trap, C.I. soil and vent pipe upto outside face of wall including 100mm dia. C.I. plug, bend and necessary pipe connection, etc complete. ( Ground Floor )

{ B } For First floor

Item No.79 :- Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 millimetre diametre and vertical pipe of 38 millimetre diametre at 0.60 metre c/c or as required and horizontal pipes of 25 millimetre diametre in three rows, all pipes of 2 millimetre thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75millimetre diametre above newel post of 75 millimetre diametre etc. complete. ( Ground Floor )

{ B } For First floor

Item No.80 :- Providing and fixing 40 milimeter diameter and 1.5 milimeter thick Stainless steel hand railing in S.S. 304 grade including fabricating, fixtures, errecting necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete. ( Ground Floor )

{ B } For First floor

Item No.81 :- Providing and fixing 45 centimeter wide steel ladder of 40 x 6 milimeter mild steel flat stringers and steps of 18 milimeter diameter mild steel bar including fixing it in M-15 cement concrete block 60 x 30 x 30 centimeter and painting the ladder with antirust primer and two coats of oil painting including all leads and lifts etc. complete.

Item No.82 :- Providing and fixing white glazed Jaquar or equivalent make urinal of series URS-WHT-13257 with Pressmatic auto closing valve of Jaquar or equivalent make having code PRS-077G, 32 millimetre diameter P.V.C. flush pipe with fitting and flushing arrangement including lead soil pipe, lead trap and soil pipe connection upto the outside face of wall etc. complete. ( Ground Floor )

{ B } For First floor

Item No.83 :- Providing and fixing White Glazed Earthenware Squatting plate (Ladies Urinal) with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 milimetre diametre P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall. ( Ground Floor )

{ B } For First floor

Item No.84 :- Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in cement mortar 1:3 including leather finish to receive rough matt finish curing and cleaning etc. complete. ( Ground Floor )

{ B } For First floor

Item No.85 :- Providing and fixing machine cut machine polished 18 millimetre to 20 millimetre thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. ( Ground Floor )

{ B } For First floor

Item No.86 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting, curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc). ( Ground Floor )

{ B } For First floor

Item No.87 :- Providing and fixing Jaquar or equivalent make series Hand shower (health faucet) with 8 millimetre diametre 1 Meter long flexible tube having code no. - ALD- / 573 GD / 537 GA / 573 GB and wall hook including necessary sockets/ union nut etc. complete as directed by Engineer in charge etc. complete. ( Ground Floor )

{ B } For First floor

Item No.88 :- Providing and fixing Jaguar or equivalent make Shower Head OHS-CHR-35497 / 35497 GD / 35497 GA / 35497 GB, with Jaquar or equivalent make shower arm code no. SHA-49483, Jaquar or equivalent make shower tube code no. SHA-549 D12, Jaquar or equivalent make hand shower code no. HSH-1937 / 1937 GD / 1937 GA / 1937 GB, with Jaquar or equivalent make divertor of code no. ALD-079 and FLR-5079K with Jaquar or equivalent make spout code no. SPJ-5463 / 5463 G / 5463 GA / 5463 GB / 5463 GD / 5463 GE, including all necessary pipe fittings and connections etc. complete as directed by Engineer in charge etc. complete. ( Ground Floor )

{ B } For First floor

Item No.89 :- Providing expansion joints in Reinforced Cement Concrete framed structure (interior column) with plain premoulded filler with confirming to IS : 1838-1961, 25 millimetre thick with 75 millimetre wide and 1 millimetre thick stainless steel plate finishing as directed etc. complete. ( Ground Floor )

{ B } For First floor

Item No.90 :- Providing expansion joints in Reinforced Cement Concrete framed structure (exterior column) with plain premoulded filler 25 millimeter thick with 75 millimetre wide and 1 millimetre thick stainless steel plate finishing as directed etc. complete. ( Ground Floor )

{ B } For First floor

Item No.91 :- Providing expansion joints in Reinforced Cement Concrete framed structure (at floor level) with premoulded filler 25 millimeter thick with 75 millimetre wide and 1 millimetre thick stainless steel plate finishing as directed etc. complete.

{ B } For First floor

Item No.92 :- Providing expansion joints in Reinforced Cement Concrete framed structure (at terrace level) with premoulded filler 25 millimeter thick with 40 millimetre wide and 1 millimeter thick stainless steel plate as required, bituminous poured filler and finishing as directed etc. complete.

Item No.93 :- Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. (including the primer coat) etc. complete.

{ B } For First floor

Item No.94 :- Providing and applying 2 Coats of 100% Pure acrylic water based paint with special heat reflectance property to withstand the harsh climate for period of atleast 10 years of approved make. Paint system should provide durable and long lasting finish with DFT of min 90 microns and should protect against concrete carbonation with R value of minimum 600 and equivalent concrete layer thickness value of min 150 centimetre. Paint should have breathability property and should be able to cover hairline cracks in the surface upto 0.5 millimetre. The paint has to be applied on a coat of high quality acrylic copolymer based alkali resistant primer with excellent penetrating properties including cleaning, with all leads and lifts at all levels etc. complete, as directed by Engineer in charge. ( Ground Floor )

{ B } For First floor

Item No.95 :- Providing and fixing 90 centimetre x 60 centimetre Granite plate engraving 10 centimetre height letter, figures including painting the lefters/figures with approved colour and shade complete.

Item No.96 :- Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. ( For Ground Floor )

{ B } For First floor

Item No.97 :- Providing and applying anticorrosive treatment for Thermo Mechanically Ttreated FE 500 steel bar reinforcement as per Cement polymer composite coating (CPCC) method developed by CECRI including cleaning the bar by means of any established mechnical method for removing the rust and delirious matter, applying rapid setting primer and cement polymer sealing coat of approved quality and licensed by CECRI including redoing the process if damage occurs during handling, stacking etc. complete as directed by the Engineer in charge.

Item No.98 :- Providing and fabricating Galvanised Iron Sheet box 100 x 300 millimetre in size made by CP square pipe 40 millimetre size and covered by Alluminium Alloy plate 2 millimetre thick including cutting, welding and fixing in position etc. complete.

Item No.99 :- Providing and applying three coats of synthetic enamel paint of approved colour to new structural steel work and wood work in buildings, including scaffolding if necessary cleaning and preparing the surface including primer coat etc. with all leads and lifts etc. complete.

{ B } For First floor

Item No.100 :- Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance and thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strictly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc., washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- charge.

{ B } For First floor

Item No.101 :- Providing and fixing chicken mesh of 22 gauge, with about 30 centimeter width at the junction of Reinforced Cement Concrete members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /Burnt Brick masonry and or tying by binding wire etc. complete. ( Ground Floor )

{ B } For First floor

Item No.102 :- Providing and fixing in position U.P.V.C. (Unplasticized Poly Vinyl Chloride) having multi-chambered outer frame section (73 x 50) millimetre with an outer wall thickness of 2 millimetre and steel reinforcement, multichambered slider frame (73x 60) millimetre with steel reinforcement, multichambered slider sash (46x 82) millimetre with steel reinforcement designed to give optimum strength, 5 millimetre thick toughened double glass with 12 millimetre spacer of good quality including alluminium track, Inter-locking profile, coextruded beadings, EPDM gaskets, silicon sealent, sliding handle, fixtures and fastenings (couplings, hinges) including with all required screws and nuts with all necessary U.P.V.C. sections as per the detailed drawing and as directed by Engineer-In- harge etc. complete.

{ B } For First floor

Item No.103 :- Providing, fabricating and erecting at site of work the tubular steel structure (shed) as per standard design and specifications having various spans in between trusses and in multiples of standard length of bays as specified as per standard specifications, inclusive of cost of steel tubular trusses, tubular columns, purlins, tie runners, foundation bolts, base plates, nuts and bolts, welding wherever required, etc. as per detailed drawing inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade, etc. complete.

Item No.104 :- Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand.

Item No.105 :- Providing & fixing of colour coated zincalume (R) AZ 150 (Min 150 Gms/Sqm total on each sides) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 millimetre base metal thickness (BMT) (0.5 millimetre TCT), Hi-strength steel with minium 500 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium, 43.4% zinc, 1.6% silicon) with COLORBOND (R) steel quality super durable polyster paint coat (with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nominal 950-1050 millimetre effective cover width and nominal 25-30 millimetre deep ribs with subtle square fluting in the five pan at nominal 180-250 millimetre centre to centre. The end rib shall be designed for anti capilary groove and return leg. The feed material should have coil manufacturer's product details marked at regular interval. Including fasteners with minium fatened with minium 25 um zinc-tin alloy coated, hex head, self-drilling screw, etc. complete. (Weight of profile 4.52 Kg/Sqm). (For 2nd Floor).

Item No.106 :- Providing and fixing plain zinc sheeting of 0.80 millimetre thick (22 B.W.G.) over the ridge hip or valley to galvanized iron sheet roofing including all fastening and bolt galvanised iron screws and bolts, lead and bitumen washers etc. complete. ( Weight of 6.8 kilogram / square metre )

Item No.107 :- Providing and fixing 100 millimeter diameter stabiliser pipe/ Poly Vinyl Chloride soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. ( BRAND FINOLEX / SUPERME / PRINCE)

Item No. 108 :-Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Item No.109 :- Supplying and erecting PVC trunking (PVC casing-n-capping) of size 32 mm with accessories on wall /ceiling as per specification No: WG-MA/CON.

Item No. 110 :- Supplying & erecting mains with 1x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/ trunking /inside pole/Bus bars or any other places as per specification No: WG-MA/BW & Note

Item No.111 :- Supplying & erecting mains with 2x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit /trunking /inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.112 :- Supplying & erecting mains with1x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit /trunking /inside pole/Bus bars or any other places. as per specification No: WG-MA/BW & Note

Item No.113 :- Supplying & erecting mains with 2x4 sq.mm F.R copper PVC insulated wire laid in provided conduit /trunking /inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.114:- Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Item No.115:- Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Item No.116:- Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.117:- Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.118:- Supplying and erecting ISI mark modular type 6 / 16A fuse unit, duly erected on provided plate and box with wiring connections complete

Item No.119:- Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Item No.120:- Supplying and erecting ISI mark modular type blanking plate one module, duly erected on provided plate & box.

Item No.121:- Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 modules duly erected.

Item No.122:- Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 modules duly erected.

Item No.123:- Supplying and erecting PVC Surface modular switch box with double mounting plate for 12 modules duly erected.

Item No.124:- Wiring for plug on board with Switch socket, copper wiring and earthing as per specification No: WG-PW/SW

Item No.125:- Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Item No.126:- Supplying & erecting LED 18W tube light fitting (4 feet) with polycarbonate housing, heat sink, integrated HF electronic driver complete.

Item No.127:- Supplying & erecting 5W-7W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Item No.128:- Supplying and erecting square / round shaped CRCA /die-cast aluminium powder coated housing LED panel ( slim edge-lit) light suitable for 13W to18W with provision for plane front frame with translucent cover fixed to the housing complete.

Item No.129:- Supplying and erecting five star rated energy saving Ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Item No.130:- Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.

Item No.131:- Supplying and erecting ‘B’ grade G.I. pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Item No.132:- Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Item No.133:- Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Item No.134:- Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP / TP MCBs of 24 poles/ 8 ways on iron/ GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Item No.135 :- Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP / TP MCBs of 36 poles/12 ways on iron/ GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Item No.136 :- Supplying & erecting original 1.25 mm CRCA sheet metal enclosures with 20A. 2 pin plug & earth socket and 20A. 3 pin plug top with 20A/30A single pole MCB complete erected on angle iron/ GI frame.

Item No.137 :- Supplying & erecting original 1.25 mm CRCA sheet metal enclosures with 30A, 3 pin plug & earth socket and 30 A 3 pin plug top with 30A triple pole MCB complete erected on angle iron/ GI frame.

Item No.138 :- Supplying, erecting & marking FPMCB 6A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Item No.139 :- Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Item No.140 :- Supplying & erecting CRCA sheet metal one way enclosures suitable for DP MCB /TP MCB /FP MCB erected on angle iron/GI frame complete.

Item No.141 :- Supplying & erecting mains with 1x6 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking /inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No.142 :- Supplying & erecting mains with 4x10 sq.mm F.R copper PVC insulated wire laid in provided conduit/ trunking/ inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No.143 :- Supplying & erecting mains with 4x16 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking /inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No.144 :- Supplying, erecting & terminating XLPE armoured cable 3½ core 50 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.145 :- Supplying, erecting & terminating XLPE armoured cable 3½ core 70 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.146 :- Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Item No.147 :- Supplying and erecting luminous / modular type call bell indicator with plastic body, heavy duty coil and indicator lamp working on 230V A.C. supply with resetting arrangement complete erected on double wooden/ sunmica board

Item No.148 :- Supplying and erecting fresh air cum exhaust fan of light duty250 V A.C. 50 cycles 225mm. 1400 RPM rust proof body & blades, wire mesh, duly erected in an approved manner.

Item No.149 :- Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation.

Item No.150 :- Supplying & erecting 22 SWG G.I sheet metal cawl sector shaped with 25 x 25 x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 300 mm as per specification no FG-FAS/MSC

Item No.151 :- Providing recess in brick wall suitable for erection of exhaust fan up to 450mm. sweep complete with grouting of nut, bolts, plastering and colour washing to match the colour of the wall for the wall thickness of 225 mm.

Item No.152 :- Supplying & erecting 20 SWG G.I sheet metal cawl rectangular / round shaped with 25 x 25x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 300 mm as per specification no FG-FAS/MSC

Item No.153 :- Providing fibre reinforced pvc flexible pipe upto 1m length with brass locking nuts and washers and clips at both ends suitable for hot water and cold water both (1set of 2 nos) complete

Item No.154 :- Supplying, erecting, testing and commissioning self contained water cooler 230/250 Volts 50 cycles nominal cooling capacity of 150 liters/hr and storage capacity 150 liters with partially stainless steel body complete. specification no. AP-WCR/WC

Item No.155 :- Supplying and erecting ultra violet water purifier with softener for safe drinking water consisting of UV germicidal tube of 8W capacity, choke made of copper wire, two indicator lamps, dual function cartridge with output of purified water 2 litre/min. with activated carbon filter and softener operating on 230 V single phase AC supply.

Item No.156 :- Providing & erecting 4 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Item No.157 :- Providing & erecting 4 Pole MCCB of 250A,415V capacity with short circuit rating 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Item No.158 :- Providing & erecting 4 Pole MCCB of 315/400A, 415V capacity with short circuit rating 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Item No.159 :- Providing & erecting floor / wall mounting, MCCB panel board with door suitable for three pole incoming 400A, 8 ways three pole outgoing up to 100A MCCB on iron frame in compliance of IEC 61439, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S)

Item No.160 :- Providing & erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 250A, 6 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S)

Item No.161 :- Providing & erecting incoming and outgoing cable alleys suitable for MCCB panel board with door of 250A incoming and 6 way outgoing or 400A incoming and 4 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB complete.

Item No.162 :- Providing & erecting incoming and outgoing cable alleys suitable for MCCB panel board with door of 250A incoming and 12 way outgoing or 400A incoming and 6/8 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB complete.

Item No.163 :- Supplying, erecting & terminating XLPE armoured cable 3½ core 120 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.164 :- Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 400 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Item No.165 :- Providing & erecting Hot dipped galvanized cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) GI sheet of 400 mm width & 20 mm height complete with necessary hardware in approved manner.

Item No.166 :- Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Item No.167 :- Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no. EA-EP.

Item No.168 :- Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Item No.169 :- Supplying and erecting fire resistant mortar (20 kg) with fire resistance class S90 as per National Electrical Code (NEC) SP30-2011 suitable to seal the openings with all kinds of cables, pipes and cable support system in steel and aluminium and plastic profiles ( Except hollow core conductors). The residual openings shall be closed with filler, as per specification no. FF-FRM

Item No.170 :- Supplying, erecting & terminating XLPE armoured cable 4 core 6 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.171 :- Making trench of suitable width and depth in soft soil for laying provided LT cable up to and including 16 sq.mm complete as per specification no. CW-EXN-CTR

Item No.172 :- Supplying & erecting G.I. pipe ‘A’ class 40 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification no. CB-CE

Item No.173 :- Supplying and erecting submersible pump set suitable for erection on open well of 3.75 KW/5 HP with 415 V 50 c/s.A.C. supply, having delivery head from 24 to 13m. and discharge from 400 to 1000 Itrs. per minute (Max efficiency at 21m head & 680 Itr discharge) & pipe of Suction 50mm / Delivery 50 mm diameter erected with necessary H type clamps as per specification no. WP-OSP

Item No.174 :- Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Item No.175 :- Supplying & erecting CRCA sheet metal one way enclosures suitable for DP MCB /TP MCB /FP MCB erected on angle iron/GI frame complete.

Item No.176 :- Supplying & erecting PVC coated 5 mm dia Brass Sensor/ electrode duly wired with nut & bolts complete

Item No.177 :- Supplying and erecting four pole metal clad ON LOAD change over switch 415V, 40A erected on angle iron / GI frame complete

Item No.178 :- Supplying & erecting Water lavel controller 230/ 415V AC., Four way for under ground & Over head tank operation.

Item No.179 :- Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.c. Submersible/centrifugal pump set upto 7.5 HP consisting of DOL starter having relay range 9-14 AMP,S.P.P., Combined ammeter /voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc

Item No.180 :- Supplying and erecting flat flexible 3 core 4 sq mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Item No.181 :- Supplying and erecting high density polythene pipe ISI mark 50 mm. dia. suitable for pressure of 6 kg. / cm2 connected to jet/submersible pump with required material complete.

Item No.182 :- Supplying and erecting 50 mm dia. gun metal sluice valve at position with necessary materials complete.

Item No.183 :- Supplying and erecting non return valve 50 mm dia in position made of gun metal complete.

Item No.184 :- Supplying & erecting mains with 4x6 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking /inside pole/Bus bars or any other places as per specification No: WG-MA/BW & Note

Item No.185 :- Supplying and erecting HMS PVC conduit 25 mm dia. with PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Item No.186 :- Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Item No.187 :- Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.

Item No.188 :- Supplying and erecting 525 V 3 phase, 50 Hz., MPP type capacitor having minimum overcurrent capacity of 1.8 In, peak inrush current capacity 300 In and minimum life 150000 hours kVAr bank of metalised polypropylene condensers (MPP) with the standard capacities of 2, 3, 5, 7, 10, 12.5 and 15 kVAr units of P.F. correction for operation on 3 phase 50 Hz. with externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and provided with terminal cover box complete erected on provided iron bracket or on floor duly tested by licensee.

Item No.189 :- Supplying and erecting ISI mark GI pipe 50 mm. dia ‘C” class position with accessories complete. Specification no. CW-PLB/GP

Item No.190 :- Supplying and erecting PVC insulated PVC round sheathed 1 sq.mm (32 no. x 0.20mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Item No.191 :- Supplying & erecting LED type indicating pilot lamp with LED colours red / yellow / green, 230 / 250V on provided box / panel with necessary material, wiring & connections etc.

Item No.192 :- Supplying and erecting marine plywood 18/19 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners, supports, nut bolts etc. complete.

Item No.193 :- Supplying and erecting LED street light fitting suitable for above 70W- 75W lamp, including lamp, with PF > 0.95 class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification No FG-ODF/FLS2

Item No.194 :- Supplying and erecting ISI mark G.I. pipe pole ‘B’ grade 80 mm dia 6 m long with pole cap, base plate in provided foundation as per specification no. OH-PL/GIP

Item No.195 :- Making cement concrete foundation including excavation ( 45 x 45 x 120 ) cm deep in 1:3:6 cement concrete, 20 to 25 mm stone metal, (45 x 45 x 45) cm / 45 cm dia. x 45 cm height plinth duly plastered, with necessary curing and finishing complete. (for 6 m pole)

Item No.196 :- Supplying and erecting Street light bracket made from 40 mm. dia ‘B’ class G.I. Pipe, 0.6m. in length along with pole cap of 300 mm length and 80 mm dia duly welded with provided leads as per specification no. FG-BKT/BPC

Item No.197 :- Supplying & erecting FRP box of size 250 x 200 x 100 mm, 2.7 mm thick complete on pole/wall as per specification no. CB-SB

Item No.198 :- Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification no. EA-EP

Item No.199 :- Supplying, erecting & terminating XLPE armoured cable 3½ core 50 sq. mm. copper conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.200 :- Making trench of suitable width and depth in soft soil for laying provided LT cable up to and including 16 sq.mm complete as per specification no. CW-EXN-CTR

Item No.201 :- Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Item No.203 :- SITC of Electric Traction Passenger cum Stretcher/Hospital Lift with · Rated capacity :- 15 Passenger/1020Kg · Floors :- G+1 floor (2Stops/2 Landings) · Travel :- 3 to 4.2 mtrs · Location of Lift Machine:- MR/MRL [applicable for Passenger Lift with MRL only & Stretcher/Hospital Lift with MR & MRL] · Rated speed :- 1.0mps VS · Doors type :- COPO/TOPO Doors with frame having clear opening of 900 mm wide x 2000mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves /frames · Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. · COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor · Clear Car size of 2400 mm wide x1000mm deep x 2200mm high · LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings · Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port, control panel duly wired with proper size & strength copper wire for power & control circuit, with provision for addition of floor/ control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class · ARD complete with necessary SMF VRLA batteries · Fireman controller having fireman switch at fire Landing, · CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for 60 days with 18" FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. · Lift Machine of Gearless PMSM of suitable kW with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength · Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work. · Minor civil work for alteration if any and erection of door frames and accessories, erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails fixing of girders for mounting lift machine etc. complete as per specification no. LFT. · Lift shaft available having clear size of 3000 mm wide x 2200mm deep, 1500mm Pit depth, 2500mm Overhead. Add ON : (1) F For vision panel having Size 100mm wide x 200mm high covered with fire rated laminated glass, having punched Jali as a part of the door panel SS sheet itself. ( 2 landing + 1 Car ) Rs 3424.05 X 3 = 10272.15

Item No.204 :- Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Item No.205 :- Supplying & erecting mains with 1x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking /inside pole/Bus bars or any other places as per specification No: WG-MA/BW Note

Item No.206 :- Supplying & erecting mains with 2x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking /inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.207 :- Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Item No.208 :- Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW for light

Item No.209 :- Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW for Fan

Item No.210 :- Supplying & erecting LED 18W tube light fitting (4 feet) with polycarbonate housing, heat sink, integrated HF electronic driver complete.

Item No.211 :- Supplying and erecting bulkhead fitting suitable for upto LED upto 12W fixed on wall. As per specification no. FG-IDF/BHF

Item No.212 :- Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Item No.213 :- Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation.

Item No.214 :- Supplying and erecting five star rated energy saving Ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Item No.215 :- Supplying and erecting ‘B’ grade G.I. pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Item No.216 :- Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Item No.217 :- Supplying, erecting & marking DPMCB 6 A to 32 A B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Item No.218 :- Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Item No.219 :- Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 poles for incoming and 6 poles for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Item No.220 :- Supplying & erecting CRCA sheet metal one way enclosures suitable for DP MCB /TP MCB /FP MCB erected on angle iron/GI frame complete.

Item No.221 :- Supplying & fixing CRCA sheet Box with earthing terminals for housing 2 Pole RCCB on iron frame/laminated board complete.

Item No.222 :- Supplying & fixing CRCA sheet Box with earthing terminals for housing 4 Pole RCCB on iron frame/laminated board complete.

Item No.223 :- Supplying, fixing and commissioning 2 pole,RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6/10/16/20/25A, as per specification no SW-RCCB/RCBO

Item No.224 :- Providing, erecting & commissioning 4 pole, 40A RCCB with added immunity which can avoid nuisance DC pulse tripping with 30/100/300 mA sensitivity complete as per specification no. SW-RCCB/RCCB

Item No.225 :- Supplying, erecting & terminating XLPE armoured cable 2 core 2.5 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Item No.226 :- Supplying, erecting & terminating XLPE armoured cable 2 core 4 sq mm copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Item No.227 :- Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Item No.228 :- Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Item No.229 :- Supplying and erecting Annealed bare copper wire of high purity of different sizes used for earthing on wall with necessary copper clamps fixed on wall/cable /conduit with screws in an approved manner..( For size 8 swg 0.1155 kg/ mtr total 25mtrx 2 run = 50 mtr for each lift total 50x 0.1155=5.775= 5.8 x3 = 17.4 kg

Item No.230 :- Supplying, installing, testing & commissioning 3 phase, 11/0.433 kV, 50 Hz., 200 kVA, oil immersed and naturally cooled outdoor type, copper wound transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40oC by thermometer in oil and 45oC by the resistance in winding at full load rating, with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5%, with standard accessories complete with test certificate with losses below 780 Watts at 50% load, 2300 Watts at 100% load as per IS:1180 - 2014 energy efficiency level II, with necessary permissions of Electrical Inspector, as per specification no SS- TR.

Item No.231 :- Supplying and erecting approved make 11 kV outdoor type gang operated air break, triple pole switch 200 A capacity with 3 post pin type insulator per phase, mounted in horizontal or vertical position with necessary channels on provided cross arm with adequate length of "C" class G.l. pipe for operating handle erected on extended square shaft. The operating handle provided with lock and key at suitable height from ground level with necessary clamp.

Item No.232 :- Supplying and erecting approved make, 11 kV outdoor type drop out fuse with insulator complete with fuse holders, fuse barrel with metal fitting, fuse element mounted on M.S. channel with working current of 15A capacity complete erected on provided cross arm.

Item No.233 :- Supplying and erecting 11 kV fuse barrel with metal fittings complete.

Item No.234 :- Supplying and erecting extra thick alkathene pipe 10mm. dia erected to enclose bare conductor wires. (use shall be restricted to H.T.)

Item No.235 :- Supplying and erecting rolled steel joist (girder) pole 100 x 116 mm (23 kg/m) with provided base plate in provided foundation as per specification no. OH-PL/RSJ (DP Structure = 2 x 11mtr = 22 Mtr) Total=22mtr

Item No.236 :- Supplying and erecting G.I. stay set for poles, including loop insulators at inaccessible height complete with anchor plate 300 x 300 x 6 mm., straining screws, G.I. stay wire 7/8 SWG, G.l. stay rod 20 mm x 1.8 m length and pole clamps duly erected in provided cement concrete foundation.

Item No.237 :- Supplying and fixing MS round base plate 25 cm dia meter and 10mm. thick fixed to pole by set screws or welded and fixed at position.

Item No.238 :- Supplying and erecting distribution class, 11 kV thyrite type lightning arrester with nut bolts, on provided MS channel as per specification no. OH-INS/LA

Item No.239 :- Supplying & erecting 100 x 50x6 mm with 4.7 mm thick web and 7.5 mm thick flange channel iron cross arm of suitable length for 2.4m wide DP structure and erecting on DP with 50x6 mm clamp as per approved method of construction and complete as per specification no. OH-PL/BKT.

Item No.240 :- Supplying & erecting MS pole bracket,for OH conductor fabricated from ISM channel, 75x40x6mm, 550 mm long for two insulators and welded with extension channel pieces of same size 300 mm in length and erecting on pole with 50x6 mm clamp as per approved method of construction and complete as per specification no. OH-PL/BKT

Item No.241 :- Supplying and erecting bracket for guarding of HT OH Line, made from channel iron 1600 mm in length and 75x40x6 mm. erected on pole complete as per specification no. OH-PL/VCA

Item No.242 :- Supplying and erecting pole clamp made from 50 x 6 mm MS flat for pole or pipe, post complete erected with 15 mm bolts and nuts, complete duly painted with one coat of red oxide and two coats of aluminium paint.

Item No.243 :- Supplying and erecting Iron, sheet metal work consisting of CRCA Sheets, Various sections of iron, Plates, Chequered Plates, Rods, Bars, MS pipes, etc. for panel board or any other purposes complete with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority 1) Equal Size 50 x50x5 mm Wt /kg= 3.8 Kg/mtr For Distribution Box Support 1.5 mtr x3 nos= 4.5 mtr For Transformer Support 3.5 mtr x2 nos= 7 mtr For Gaurding 2mtr x4 nos = 8 Mtr Total = 19.5 Mtr Total Wt = 19.5 x3.8 = 74.1 kg ----(I) 2) ISMC chaannel = 50x10 mm wt /kg 3.9 kg per mtr Total Length = 3 mtr Total Wt = 3 mtr x 3.9 kg/mtr = 11.70 kg------(II) Total Wt.= I +II =74.1 + 11.70 = 85.8 Kg

Item No.244 :- Supplying and erecting porcelain pin type insulator with G.I. pin suitable for 11kV line, complete as per specification no. OH-INS/PN (DP structure=3Nos)

Item No.245 :- Supplying and erecting porcelain disc type insulator with necessary hardware suitable for 11kV line, complete as per specification no. OH-INS/DI I (Tapping Pole = 9 Nos)

Item No.246 :- Making cement concrete foundation including excavation (60 x 60) cm x deep 1/6 of pole length in 1:3:6 cement concrete 20 x 25 mm stone metal, 45 cm x 45 cm x 45 cm /45 cm dia. x 45 cm. height plinth duly plastered, with necessary curing and finishing complete. (for above 9 m poles)

Item No.247 :- Making cement concrete foundation including excavation (60 x 60 x 150) cm deep in 1:3:6 cement concrete, (20 to 25) mm stone metal with necessary curing and finishing complete.(for stay).

Item No.248 :- Providing earthing with Galvanised cast iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification No. EA-EP (Detail are given in Drawing)

Item No.249 :- Supplying, erecting & terminating XLPE armoured cable 1100 V. 3½ core 185 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.250 :- Supplying and erecting GI sheet 1.6mm (16 SWG) caution board of size 250 x 200 mm duly painted with red oxide and enamel paint in Marathi and Hindi erected at position for HV/EHV installation.

Item No.251 :- Supplying & erecting barbed wire two ply with 12 SWG ply and 12 SWG barb with a gap between two bars of 75 mm. firmly fixed on provided angle supports with necessary materials. (6.044 meters/kg.)

Item No.252 :- Making transformer plinth (1.5 x 1.5 x 1.5) m in size with necessary excavation in ground with 150 mm. thick M- 10 PCC at the bottom and top and 250 mm. thick, burnt brick wall constructed at periphery and remaining hollow portion shall be filled with 40mm hard broken aggregate. External surface duly plastered by 12 mm thick including watering etc complete.

Item No.253 :- Supplying and erecting fencing of section having size 2450 mm in height from ground level and 1200 mm width with angle iron frame work erected in CC foundation and painted complete as per specification no SS-AS/FSG total length of fencing = 18.5m/1.25=14.8=15 nos

Item No.254 :- Supplying and erecting 50 x 50 x 6 mm angle iron as corner support 2m long fixed at the middle of the fencing frame and the other side inclined at 30 degree angle, in cement concrete foundation of 15 x 15 x 40 cm complete duly painted with one coat of red oxide and two coats aluminum paint complete.

Item No.255 :- Supplying and erecting double leaf hinged door each 1500 mm in width x 1850 mm in height using B class, GI pipe with angle iron supports, chain link wire mesh (jali) complete supported on channel iron, erected in foundation, and painted complete as per specification no SS-AS/DLD

Item No.256 :- Making trench of suitable width and depth in hard murum / tar road for laying provided LT cable of 16 sq. mm & above and covered with half round hume pipe complete as per specification no. CW-EXN-CTR

Item No.257 :- Supplying and erecting LT/CT multifunction DLMS compliance energy meter of accuracy of class 0.5 , 3x240V,50 Hz with optical & RS232 port, backlit LCD, measures & Displays Trivector Energy, load survey, TOD, tamper detection & logging, power ON /OFF events, instaneous parameters of Rating -/5 Awithdisplay in absence of power complete with zero adjustment & test certificate from manufacturer erected on provided M.S. box and connected to CTs.

Item No.258 :- Providing and erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio with 15VA burden erected in providedCRCA box duly secured with insulating materials connected to the meter with test certificates.

Item No.259 :- Supplying and erecting GI sheet 1.6 mm (16 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. 1) For Distirbution Box Size 1.5 x 1.5 x 2 nos =4.50sq mtr 1.5 x 0.46 = 0.69 x 2 = 1.38sq mtr 1.5 x 0.46 = 0.69 x 2 = 1.38sq mtr Total = 4.50 +1.38+1.38= 7.26 sqmtr x 2 nos =14.52 sqmtr (1. Distribution Box at tranformer 2 distribution board near building ) 2) DTC Metering Box 0.6x0.6x2 nos = 0.72 sqmtr 0.6 x0.3x2 nos = 0.36 sqmtr 0.6 x0.3x2 nos = 0.36 sqmtr Total = 0.72+0.36+0.36 = 1.44 sqmtr Total = I+II = 14.52 +1.44 =15.96 sqmtr

Item No.260 :- Providing & erecting 4 Pole MCCB of 250A,415V capacity with short circuit rating 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB & Note

Item No.261 :- Supplying & erecting of required size Electrolyte Copper Flexible Braided bus Patti or bar in bus bar chember/in panel or any other purpose, suitable for 500 volt with require capacity with 99.9% copper purity with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as per specification no. BCPBB size 50x6 mm flat wt/kg-2.60kg, total length-4 mtr , total wt= 4x2.68=10.72 kg x 2 = 21.44 Kg (1. Distribution Box at tranformer 2 distribution board near building )

Item No.262 :- Supplying & erecting 415V 200A porcelain base neutral link complete erected in provided MS box complete.

Item No.263 :- Supplying and spreading stone metal 25 mm size for 100 mm depth above the ground level complete.

Item No.264 :- Supplying and erecting ACSR conductor of size 6/1-3.66 mm complete.(Mink) (255 kg/km) as per specification no. OH-CON/ACSR

Item No.265 :- Supplying , erecting & terminating 3 x 95 sq. mm. aluminium 11 kV(E), XLPE armoured cable on wall/ceiling or laid in provided trench / pipe in an approved manner as per specification no. CB-HT

Item No.266 :- Providing and erecting Heat shrinkable indoor termination kit for 11 kV ( E ) XLPE HT cable 3x up to 95 sq. mm. with necessary material as per specification no. CB-JT/HT

Item No.267 :- Supplying & erecting G.I. pipe ‘A’ class 50 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification no. CB-CE

K.S.POWAR

M/s Kranti Construction