SPECIAL REPAIR TO OTM ACCN, ROOF COVERING AND PERIMETER SECURITY FENCE AT BENGDUBI MIL STN UNDER GE BENGDUBI

Amount

Demolition of cement concrete (un-reinforced) as in benching, cover fillets, roof kerbs, kerbs PCC padding over roof and of any description & in any position not otherwise specifically provided-for, including taking down existing un-servicable waterproofing treatment from roof slab surfaces, roughening of old concrete surfaces by picking, cleaning the surfaces by wire brush and also including disposing off the retrieved debris outside the premises / site, complete all as specified and as directed.

M&L for cement concrete 1:2:4 type, B1 (using 20 mm graded stone aggregates) as in copings, Chajja kerbs, benching at the junction of roof & parapet, roof kerbs, staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for 25mm thick (average thickness) cement concrete type B-0 (1:2:4) (Using 12.5 mm graded stone aggregates) mixed with liquid water proofing compound as in padding over roof etc, including finishing the exposed surfaces of the concrete even and smooth without using extra cement, complete all as specified and as directed. Note:- Payment for liquid WPC shall be measured and paid for separetely.

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications, complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying 3mm thick APP modified water proofing polymeric membrane reinforced with non woven polyester fibre using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm. (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption,% - Not more than 0.15. (ix) Cold flexibility - (-) 50C. (x) Dimentional stability % change = Maximum 1%. (xi) Heat Resistance - Does not dirp at 1200 C Note : The quoted rate shall also be deemed to include for cutting grooves of size and shape as required in the parapet wall for tackling the APP membrane in the wall including making good the surfaces of groove as well as damaged surfaces of the wall after tackling of membrane in CM 1:3 to match with the adjoining surfaces.

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane, complete all as specified and directed.

Supply only liquid water proofing compound, complete all as specified and as directed.

Dismantling posts or struts (steel or RCC), any section including taking out embedded portion from the natural ground, making good the disturbed ground, includung necessary excavation & earth work, complete all as specified and directed.

Dismantling posts or struts (steel or RCC), any section including taking out embedded in concrete portion, making good the disturbed ground, includung necessary excavation & earth work, demolition of concrete, complete all as specified and directed.

Dismantling of fencing wire of any description and in any portion, complete all as specified and directed.

Excavation in post holes and/or similar holes each not exceeding 0.50 Cum in any type of soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, removal of surplus spoil/soil to a distance not exceeding 50 metre from the premises/site, complete all as specified and as directed.

M&L for cement concrete in foundation blocks for embedding fencing posts, foundation filling and mass concrete type D-2 (1:4:8) using 40 mm graded stone aggregates, complete all as specified and directed.

S & F Galvanised, 2 strand, steel barbed wire 2.24 mm dia, barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured & paid for separately), complete all as specified and as directed.

M&L for mild steel comprising of the angle iron, flat iron etc using steel conforming to Fe-290 Gde E-165 as in posts and struts in fencing inclluding cutting tops to shape as diected, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including necessary bolting/ riveting and embeding in concrete and similar work, complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) (diameter of neck 11 to 15 mm) with hexagonal or square heads at one end or screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 05 cm but n. exc 10 cm long, complete all as specified and as directed.

M&L preparation of new steel & iron surfaces of any description exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed

S&F Mild steel bars 10mm dia round bars and over, conforming to Fe 290 (Gde - E-165), cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for holding the chain link fencing in the position etc, complete all as specified and as directed.

Fixing only chain link fencing of any size including line wires, any mesh, size and type, to any type of standards, rails, straining bolts etc, inclding provision of binding wire, complete all as specified and as directed.

Supply only of chain link fencing made of 3.15 mm dia mild steel galvanised wire and 100x100mm size mesh as in fencing, complete all as specified and as directed.

Dimantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges etc, complete all as specified and as directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

Dismantling wrought iron as in rafters, purlins, truss etc and/or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

S&F mild steel rolled sections & plates [Fe 410-W (Gde E-250) quality - B] as in main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, hold-fasts, lugs, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site outside the premises, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:6) on the surfaces of brick work or concrete, finsihed even and fair, complete all as specified and as directed.

M&L for preparing newely plastered surfaces of wall and applying two coats of cement base paint, complete all as specified and as directed

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in hold fast blocks, lugs blocks, coping, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

S&F Decorated PVC False ceiling consisting of 600mmX600mmX5mm (± 0.25mm) thick plain PVC sheet of density 600 Kg/Cbm of the specified make, used as a panel insert in a frame work made using powder coated aluminum T-section of size 25mm x 25mm of 19 guage or 1mm thick in square pattern of grid size 600mm x 600mm. The aluminum frame work shall be supported from the ceiling by providing J Hook or 4 mm dia GI wire of required size to maintain the proper levels etc as directed. The aluminum frame work shall be supported on side wall with the use of powder coated aluminum Angle section of size 25mm x 25mm of 19 gauge or 1mm thick angles etc. complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets, and existing frame work also, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), Complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position like trusses, rafters, purlins etc, complete all as specified and as directed.

S&F of GI frame work (size of grid 600mm x 600mm) for seamless ceiling comprising GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including provision of Hangers of 4mm dia G.I wire (length as required at site), complete all as specified and as directed.

S & F 4mm thick Non-asbestos fibre cement building boards (4mm thick pre-painted designed type E-Board) to frame work with screws in ceiling (flat and/or slopping) and in jointless finish with & including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Note :- The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in Beams, cantilevers, bressumers, lintels over 1.5 metre span, complete all as specified and directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L TMT bars 8mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

Use and waste of formwork to Beams, cantillevers, bressumers, lintels, shelves and similer items for rough finished flat surface of concrete, complete all as specified and as directed.

M&L for Brickwork with fly ash Bricks, straight or curved on plan exc 6m mean radius built in Cement morter 1:6, complete all as specified and directed

M&L for brick work with fly ash Bricks, straight or curved on plan to any radius built in CM 1:4 as in half brick thick walls, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection etc, surfaces finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregates) as in sub-base of floors etc, finished even & rough, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

All as per Item No 45 above but for vertical surfaces such as skirting etc, over and including 10mm thick back coat in CM 1:4.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, also including disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, also including disposing off the debris outsite the premises, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates includings necessary provision of lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

S&F factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates includings necessary provision of lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

S&F Factory made 35mm thick flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both sides including provision of 4mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

S&F factory made IInd class Hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35mm thick plain framed, panelled shutters ( Two panels),with lock rail and penel of 9mm BWP commercial ply or 12mm veneered particles board with commercial veneering on both faces. the size of rail and stile as per IS 1003 (Part-I), complete all as specified and as directed.

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt 200 mm long of extruded section, complete all as specified and as directed.

S&F 100mm size butt hinges, medium weight, cold rolled, mild steel, complete all as specified and as directed

Taking down of steel windows, vents (including grills/guard bars, where occurs), including cutting holes for removing the lugs etc, also including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

S & F factory made steel windows with side hung shutters including box type hinges with steel handle, and peg stay, complete with glazing bars, dovetaild or welded, also including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

All as per item No 58 above but steel window without glazing bars.

S&F Factory made, steel ventilator with top hung shutter including hinges, steel peg stay, including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

M&L for the Framed work such as gratings, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality, glazing for steel surrounds with & including oil putty, in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

All as per item No 62 above but sheet glass frosted on one side.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with and including stainles steel wire staples etc, complete all as specified and as directed.

M&L for complete removal of existing treatment from the external surfaces of wall etc, thereafter prepartion the surfaces and applying two coats of cement base paint, complete all as specified and as directed.

M&L preparing new wooden surfaces of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L for applying two coats of Birla/Asian wall care Putty (total thickness not less than 2mm) after preparation of old/new wall/ceiling surfaces, complete all as specified and directed.

M&L for preparing new surfaces of walls duly applied with wall care putty, applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for complete removal of existing treatment of walls, preparing the surfaces of walls duly applied with wall care putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for factory fabricated Hydraulically machine pressed cement concrete chequered tiles of size 300x300X25mm thick (with grey cement and pigment), set in neat cement slurry including provision of 15mm thick cement screed bedding layer in CM 1:4, tiles joints shall be grouted and immediately after grouting, the joints shall be pointed flush in separate process in CM 1:3 mixed with pigments to match the colour of the Tiles, complete all as specified and directed.

S&F in repairs stainless steel decorative curtain rod of 25 mm bore with wood finishes, complete all as specified and as directed.

S&F brackets and funnel caps suitable for the curtain rod to be provided under item No 71 above, complete all as specified and as directed.

M&L preparation of new steel & iron surfaces of any description not exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Taking down carefully existing aluminium/copper point wiring (light / fan / socket or power point) complete, with all unserviceable fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Taking down existing unserviceable distribution board, switch fuse unit, enclosure for MCB / DB (inclusive of MCBs etc of any type and capacity),metal plug socket DB(incl MCBs etc) and making good the disturbed surfaces, complete all as specified and as directed.

Material and labour for point wiring for one light point/one fan point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 77 above but for one switch socket outlet, 5 Amp on independent board, complete all as specified and as directed.

All as per item No 77 here-in-before but for one socket with other switch/switch socket outlet 5 amps on the same board, complete all as specified and as directed

All as per item No 77 here-in-before but for one15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

Supply and fixing switch piano flush type, single pole, one way, 5 Amps, complete all as specified and as directed.

Supply and fixing switch socket out let multipurpose, 3 pin, 15 Amp and one 3 pin, 5 Amp, complete all as specified and as directed.

Supply and fixing switch socket outlet 5 pin, 5 Amp, flush type, complete all as specified and as directed.

Supply and fixing ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

Supply and fix electronic fan regulator, flush type, delux rotary step type, 5 step, not less than 100 watt, complete all as specified and directed.

Supply and fixing sheet metal enclosure for MCBs DBs, Double Doors, phosphatised, Powder coated , single pole and neutral (SPN), 240 Volt , 12 Ways with and including 100 Amps rated bus bar, provision of blanking plates as required, also cutting nitches/opening in the wall for accommodating the DB's, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and as directed .

S&F MCB 'C' Series, SPN, 20 to 32 Amp, 240 Volts, reputring capacity 10 KA, complete all as specified and directed.

Supply and fixing MCB,Single Pole, C series, 10kA ruputring capacity, 6 to 32 Amps, 240 Volts, complete all as specified and as directed.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation, laying of cable, pipe etc and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc, complete all as specified and directed

Removing excavated material to a distance not exc 50.00 metre and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Material and labour for well burnt Sub class 'B' old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed.

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm 2core laid in trenches /along poles/on wall etc, complete all as specified and as directed Note For item No 94 : Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately.

Materials and labour for earthing complete with galvanised earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 metre below normal ground level with top edge of the plate not less than 1.50 metre below normal ground level connected to galvanised earth lead GI wire of 4mm dia by means of bolts, nuts and washers and check nuts of galvanised iron or steel GI earth wire protected by 25 mm bore light grade galvanised iron pipe including of 20 mm dia medium grade GI water tubing sheet metal 4mm wire mash funnel, charcoal or coke and common salt in paint and testing on completion as shown on electrical plate No.5 ofm SSR Part-I. including taking out unserviceable one, complete all as specified and directed.

Material and labour for galvanized iron tubing 50mm bore light grade with all fitting for protection of cable, laid in trenches/ along poles /wall/floor incl necessary clamps, bolts/nuts, complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid separately.

Supply and Fix Lamp holder, PVC/Polycarbonate type with back plate, complete all as specified and directed.

S&F ceiling fan, 3 star rating, white in colour,1200 mm sweep, 230V, SP, complete with accessories, MS hook made out of mild steel flat iron of size 25 x 5mm of the rquired length for hanging of ceiling Fan, also making connection with and including copper conductor cable from ceiling rose to fan, also including taking down of existing Fan and depositing the same in MES store yard of GE, complete all as specified and as directed, Make : Usha model TECHNIXPLUS or Equivalent of make Havells/Bajaj as approved by the GE.

S&F street light bracket made out of 25 mm bore GI Light grade pipe 1.00 M long bent to the shape as required for steet light fittings pronded with two pairs of MS Flat Iron 50mm x 6mm clamps of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete including taking down of unserviceable one, complete all as specified and directed.

Supply and fix LED tube light fitting 1 X 20 Watts (4 Ft) 240 Volts, Ultra bright polycarbonate LED Tubelight with very high efficiency suited for installation in & including T8 tubelight with G13 lamp holders, complete with and including all accessories, internally pre-wired and including making connection by providing 3 core 1.5 Sqmm PVC insulated stranded copper conductor cable, complete all as specified and directed. Make and Cat No of T-8 Tubelight : HAVELLs Cat No PHOTONULTRAE2.01213T8SSTL20WLED865SPC or equivalent of make Crompton/PHILIPS/BAJAJ as approved by the GE. Make and Cat No of T8 Tube Light Fittings : HAVELLs Cat No Regal Batten T8UPTO1X22WSSBSWH or equivalent of make Crompton/PHILIPS/BAJAJ as approved by the GE.

S&F in repairs Building Security light 1x15 watt, presure die-cast housing with individual LEDs as light source and Lens embedded PC cover having TOP opening, separate driver compartment with IP 66 protection and impact resistance of IK-07, make BAJAJ : Cat No. BRLEP15WLED or equivalent of make HAVELLS/PHILIPS/CROMPTON as approved by the GE and provision of copper conducor cable for connection, complete all as specified and directed.

Taking down of existing Under Ground cable from trenches/ along wall/pole etc, complete all as specified and directed. Note :- Excavation & Earth work shall be measured & paid for separately.

M/S JANATA CONSTRUCTION

M/S G D CONSTRUCTION

CHAKRABORTY AND SONS

M/S AHUJA TRADING