IMPROVEMENT TO BLDG NO P 412, ADDN ALTN AND IMPROVEMENT TO BLDG NO P116 MENAKA AUDITORIUM AND SPECIAL REPAIRS TO BLDG NO P 49 COE AT INS SHIVAJI LONAVLA

Amount

S&F coloured aluminium composite panel, 4mm thick, fixed on projected frame work , joints sealed with and including silicon sealing agent etc complete all as specified and as directed. Notes for Item Nos :- (i) Make of aluminium composite panels- Cat No A-45 with colour shade AP-02 (Metalic silver) manufactured by Alupan plus or equivalent cat manufactured by "Eurobond/National bond". (iii) The grid work and panelling works as required shall be executed all as specified above and as per manufacturers instructions of the makes specified in the description of the item. The decision of the Garrison Engineer in this regard shall be final and binding. (iv) Makes of various materials required for above items shall be as under :- (a) Aluminium section- Jindal/Hindal Co. (b) Sealing agent - GE/Wacker/Dow Corning. (v) Almn frame work will be paid seperately. Note: Item No 1,2 is required to be fixed at height upto 8 m above FFL. Rate quoted is deemed to be included for scaffolding required to work at above mentioned height.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Rendering 10 mm thk in CM (1:4) as in backing coat of cement plaster for laying of wall tiles

Glazed ceramic tiles in Dado/ Skirting in vertical surface 350x250mmx7mm/450x350x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match with surface

Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6

M& L for Dark shade Vitrified ceramic tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with surface

Taking down chowkats with shutters( without taking off shutters from the frame) exc1.5 sqm and n.exc 4 sqm each

S&F powder coated aluminium section in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed (Aluminum section shall be of make Jindal / Hindalco / Indalco). Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

Taking down chowkats or frames with shutters not exc 1.5 Sqm with shutters (without taking off shutters from the frames wooden/Aluminium) complete all as specified and directed

Supply only 5mm thick glass ordinary quality in plain of any size including rubber beading or gasket for aluminium section complete all as specified. complete all as specified.

Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in kitchen platform and similar work laid, bedded and pointed in cement mortar complete all as specified and directed.

M&L for granite 18 to 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,jambs,cooking platforms, door frames and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade

Rounding to edges of granite stone slabs edge, such as in steps, cooking platform and other similar situations

S&F framework of aluminium box pipe of size 70 x 40 mm made out of 16 gauge aluminium sheet projected not exceeding 50 cm away from wall columns/corners/turnings and spacing not exceeding 90 cm c/c (both ways) etc complete all as specified and as directed.

M&L for complete removal of existing treatment of old painted wall surfaces and applying two coats of oil bound distemper over a coat of primer over 3mm thick wall care putty of approved make & shade on walls and other places as directed by Engr-in-Charge. (Rate including the required scaffolding & other accesories required for painting)

Dismantling of CGI/PGI /TCT sheet in roofing any gauge and any thickness including ridge, valley/gutter etc.

M&L for prefabricated puf roofing panel with one side trapezodial sheet & other side plain sheet with slight rib of 0.50mm TCT PPGI (Off white RAL 9002) with 60mm core of polyurethene foam of density 40kg/M3 (+2Kg/M3) fixed with self tapping screws all as manufacturer's instructions including all cutting as required as per site conditions having following specifications complete all as specified and as directed. (a) Top Sheet - Profile as approved by GE (b) Bottom sheet - Plain sheet with slight ribs (c) Panel thickness - 50mm (d) Facing material - 300 Mpa Galvalume steel with 150cms Aluminium Zinc (e) Facing material thickness - 0.5mm TCT (f) Facing material coating - DFT 20 microns colour coated Rmp/Smp/PVDF coating over 5 microns primer.

Pre painted galvalume aluminium zinc coating GI based plain sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated sheet trapezodial pattern matching with existing profile, 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets/Aluminium snap grid

M&L for GI frame work of seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall and using nylon sleeves and screws at 450mm center to center/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.50mm fixed to intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and as directed.

S&F Gypsum beard 12mm thick in ceiling fixed with screws as per manufacturer instruction including applying two coats of oil bound distemper over a coat of alkali resistance primer complete all as specified and as directed.

M&L for cutting ,grooves or rebates n.exc 15cm girth and triming surface for inserting pre-painted galvatume sheet with or without reinforcement.

M&L for PCC 1:2:4 type B0 (12.5mm graded agg) as in roof kerbs coving over chajjas and similar locations rounded or chamfered on edges.

S&F Rolled mild steel section as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc quality conforming to Fe 410-W (Gde E250) quality-A.

Preparing new steel Surfaces of any des-cription, over 10cm in width or grith, not otherwise described and applying two coats of Synthetic enamel paint over a coat of red oxide

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for Rendering 15 mm thick CM 1:6 on fair faces of brick work or concrete surfaces and to be finished even and smooth(without using extra lime or cement)

M&L for Preparing newly plastered surface and primng with alkali resistant priming paint and applying 2 coats of oil bound distemper on walls over 3 mm thk wall care putty

Dismantling of existing water proofing treatment treatment consisting of cement mortar,tarfelt and foreign materials etc incl cleaning the surface and removal of dismantled materials outside MD land as direted by the Engr-in-charge.

M&L for screed bed or bedding layer 15mm thick in cement mortar (1:4) with water proofing compound for laying membrane (Note:- Water proofing compound shall be measured seperately

M&L for water proofing treatment to RCC roof slab all as specified below and as directed:- (a) Apply one coat of bituminous primer @ 0.25 Kg/Sqm. (b) Apply a coat of blown type bitumen grade 85/25 heated to working temperature of 180 degree centigrade and applied at 1.20 Kg/Sqm of the surface area. (c) Laying APP polymer modified membrane 4mm thick with non woven polyster reniforcement weighing not less than 4.00 Kg/Sqm applied by torch application method. (d) Apply a coat of blown type bitumen grade 85/25 heated to working temperature of 180 degree centigrade and applied at 1.20 Kg/Sqm of the surface area. (e) Apply a coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm.

M&L for 50 mm thick (average) cement concrete 1:3:6 C-0 mix (12.5 mm graded stone aggregate) in padding over roof.

Disconnecting existing tanks,exc.500 ltrs and n.exc.1000 ltrs capacity,setting aside (or lowering if required)for repairs,cleaning etc,removing all scale and dirt etc.from mouth of circulating pipe etc and hoisting if required,reconnecting and refixing in position.

Taking up or down steel tubing 20mm bore and connections including cleaning for refixing or removing from site.

All as per item 38 above but for 15mm bore.

Supply and laying 20mm dia tubes galvanized steel,medium grade,with all fittings and fixed to walls/celling or laid in floors all as spceified and directed.

All as per item 40 above but for 15mm dia.

Taking down existing steel /aluminium ventilator/ window of any size or any description

M&L for powder coated aluminium two track, two to four shutters (of equal width), sliding type windows without sash bars including necessary jointing clips, rubber packing, neoprene rubber gasket, aluminium snap beading, screws, aluminium fittings, handles, locking arrangement (star lock), bearings (two No's for each sliding shutters) & 4.00mm thick plain glass for glazing with & including following powder coated sections as given in 'JINDAL' catalogue complete all as specified and as directed (i)Frame (Bottom)-20956 (ii) Frame (Top & Side)-20966 (iii) Shutter vertical (Handle lock)-20846. (iv) Shutter vertical (Int lock)-20845. (v) Shutter (Top)-20844. (vi) Shutter (Bottom)-20847. Note :- (i) The window opening shall be provided with two to four shutters of equal width. (ii) The shutters shall be placed in such a manner that at a time the entire width of window can be utilized as fully glazed window. (iii) The thickness of the powder coating shall not be less than 0.5 micron & the tint shall be as decided by GE. (iv) Unit rate quoted shall be deemed to include for sealing the gap of frame with Jamb and Cill (alround) using silicon gel at the rate of 0.05 lit/m for both faces of window.

Supply and fix aluminium powder coated ventilator partly fixed and partly louvered type without sash bar, section as per designation 63400 of IS 737 , frame and intermediate made out of aluminium section of size 50.80 x 25.4x 0.95 mm (catalouge No 14027 of M/s Jindal) including necessary jointing clip, rubber packing, anodised snap beading srews alongwith 4.00 mm thick pin headed glass for louvers and glazing etc complete all as specified and as directed

M&L for Machine cut green marble slab, 18-20mm thick, single piece in full length of window cill/jamb over and including cement mortar screed/backing coat, 15 mm thick in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations

Rendering 15 mm thick of fair faces of brick work or concrete surfaces in CM 1:6 using water proofing compound

Supply only integral water proofing compound.

Rendering 15mm thick cement plaster in CM 1:4 as brick concrete or stone surfaces finished even & smooth without using extra cement .

M&L for preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash on wall. All as directed by Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, Fan, Socket or power) fitting such as switches, ceiling roses, pendents, regulators, sockets etc complete removing material to store for keeping in safe custody and making good disturbed surfaces of walls, floors etc all as specified as directed.

M & L for point wiring with 1.5 sq mm single core PVC insulated cable 1100 V grade with multistranded copper conductor drawn through PVC casing and capping with all accessories fixed to wall /roofs ceiling etc and incl provision of 1.5 sq mm PVC insulated and unsheathed copper conductor as earth continuity conductor and connected to common earth dolly incl fabricated steel terminal box made out of 1.6 mm thick MS sheat concealed in the wall with 3 mm thick laminated sheet top cover/PVC fiber board of suitable size for mounting the modular switches , socket outlets , fan regulators etc all as specified and directed for One light/fanpoint controlled by one way switch.

Supply and fix in repairs modular switch 6 Amps, 1 module complete all as specified and as directed.

Supply & fix in replacement LED Bollard (TETRIS) of 9 watt in rectangular shaped victorian design with opel acrylic diffuser and IP 65 protection including taking down old U/S light fitting complete all as specified and directed .Make:Bajaj Cat No-BZRSQL 36W XL NW or equivalent to CG/Philips/Wipro/Shakti

Supply & fix in replacement Recess mounted LED (DELTA) designer delite unique designed high efficiency LED Recessed 2 x2 luminaire including taking down old U/S light fitting complete all as specified and directed .Make:Bajaj BZRSQL 36W GZ1 WH (skylux led) or equivalent to CG/Philips/Wipro/Shakti

Supply & fix in replacement LED Flood light (AMAZE LED)200 watt warm white including taking down old U/S light fitting complete all as specified and directed .Make:Bajaj Cat No-BJFL 200W LED I WW or equivalent to CG/Philips/Wipro /Shakti

Supply & fix in replacement LED downlighters(RADIANCE LED) with low depth round & larger dia 18 watt warm white including taking down old U/S light fitting complete all as specified and directed .Make:Bajaj Cat No-BPSLR 18W WW or equivalent to CG/Philips/Wipro/Shakti

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 2 core

Supply & fix exhaust fans metal body complete with and accessories 230 V,300 mm sweep complete all as specified and as directed. Note-Rates for making hole for exhaust fan is deemed to be included in coated rates no extra payment shall be done in this account.

M&L for earthling complete with galvanized GI earth plate electrode of size 600x600x6.00 mm, buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanized earth lead wire 4.0 mm dia by means of volts, nuts, check nut and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate as shown in electrical plate No 3 of SSR Part I 2009,20 mm dia watering pipe medium grade 1.50 mtr long GI protection pipe light grade 15 mm dia from earth pit to main board (NOTE:- maximum length of GI protection pipe with each earth shall not be less than 7.5 mtrs) including necessary pit with cover , including testing on complition.

S&F submain wiring with unsheathed multi-stranded copper conductor cable 1100 volts grade drawn through PVC Casing capping for two runs of 6 Sqmm single core and one run of 4 Sqmm PVC insulated copper conductor for earth continuity wire complete all as specified and as directed. Note :- Two run of single core cable with one run of earth continuity conductor and PVC conduit and accessories will be measured as one length including cutting chasing in wall complete.

Excavation in trenches n. exc. 1.5 M in width and 1.5 M in deep for laying of pipes and getting out in Soft / loose Soil

All as per item No.63 Herein before but in hard dense soil

Returning, filling in, including spreading, leveling, watering and well ramming in layers n. exc. 25 cm.

Removing excavated material n. exc. 50 M away and depositing where directed at a level n. exc. 1.5 M above the starting point complete all as specified and as directed.

M&L for providing dry river sand / crush stone dust for cushioning to UG cable including punning down of sand in layers all as specified. Note :- Cushioning will be measured and paid after punning down.

Supply and laying factory cast, unreinforced precast concrete cable cover factory made embossed the mark “LT CABLE” class LV type1 flat size 250x150x40 mm laid in trenches as specified and as directed.

Supply and lay in trenches / along the wall / floor pipes GI light grade of size 100 mm dia with and including all fittings and accessories including taking down old U/S pipe complete all as specified and directed for cable protection

M&L for preparation of new plastered wall and applying two coats of weather proof anti fungal paint after applying a priming coat of alkali resistant priming paint complete all as specified and as directed.

SHAILENDRA B TULSANI

RK AND SONS CREATION

DWARKESH STRUCT-CON

seema enterprises

M/s S.D Construction Co