Renovation of Bathroom beside the house of Faku Dom at Laldighirdhar under Booth No 104 in ward no 11 Apas

Page No- 11, Item No- 10, Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed.

Page No; 32; Item No; 1, Labour for chipping of concrete surface before taking up plastering work directed.

Page No; 32; Item No; 29, 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.

Page No; 189; Item No; 1(i)(c)2(ii)(a), Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](i) With 1:6 cement mortar. (c) 15 mm thick plaster

Page No; 42; Item No; 36(f), Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (f) 25 mm to 30 mm shuttering without staging in foundation.

Page No; 43; Item No; 40(a)(1), Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation, basement and upto roof of ground floor/upto 4 m. (i) Tor steel/Mild Steel I. SAIL/ TATA/RINL

Page No; 26; Item No; 10(i), Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety

Page No; 280; Item No; 1.b, Supplying and laying true to line and level Anti-Skid, full Body, Ho,ogeneous & Granular finish Vitrified Tiles conforming to IS: 15622-2006 & IS 4457-2007 and testing shall be made in accordance with IS: 13630[Non-modular sizes for tiles with skid resistance>0.5, Mohr's hardnees> 5.0, staining resistance: Class-1, water absorption: E< 0.5%], Mor> 35 N/sqmm. in Internal area of building e.g. Toilet bolck, Passage, corridor, Acessible open Terrace etc. set in 20mm sand cement mortar(1:4) and 2mm thick cement slurry at back side of tiles using cement @ 2.91 kg/sqm. ...................................................specification and direction of Engineer-in-charge. (white cement, synthetic adhesive and grout material to be supplied by the contractor) In ground floor: Sizes- 600mm X 600mm X 10mm with breaking strenght> 1500 N.

Page No; 64; Item No; 35, Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m. (i) Coloured decorative

Page No; 105; Item No; 15, Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both faces of M.S./ W.I. gate etc. with point welding at not more than 150mm apart complete in all respect as per design including cost of all labour and materials.

Page No; 111; Item No; 2(a), Welding in M.S. structural work with gas or electric: (a) Tack weld.

Page No; 115, Item No; 2, (A) Supplying fitting and fixing door frame with M.S. angle as per drawing & direction of required section.The holes for counter sunk machine screw & nuts will be such as to fit 8 to 10 mm Iron screw. The counter sunk nut to be welded . The nuts are to be welded after careful checking with screw.All welding spots should be properly filed or rounded smooth including cost of welding hinges for hinge cleats , lugs for hasp bolt, socket bolt etc. and necessary M.S. clamps of 25mm x 6mm flat 225mm long as per direction welded to the frame fitted and fixed in position excluding cost of concrete.

Page No; 104; Item No; 13, (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr

Page No; 198; Item No; 1, Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge)

Page No; 200; Item No; 1b, (a) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Page No; 200; Item No; 1 (b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Page No; 200; Item No;2(A)(a)(iv)(b)(iv), (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white)

(b) On steel or other metal surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white)

Add 9% SGST

Add 9% CGST

Add @ 1% loabour welfire cess