GE/863/EWS-T-45 OF 2024-25

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level), complete all as specified and directed.

M &L for 25 mm thick PCC 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) as in sub base of floors, etc., complete all as specified and directed by Engr-in-charge.

M&L for screed bed or bedding layer of morter 15 mm thick cement mortar 1:6 for laying floor finishes to receive floor tiles/granite complete all as specified and directed.

M&L for Vitrified Ceramic tiles Light shade 10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the color of tiles, complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 Type C-1 using 20mm crushed stone aggregate as in plinth protection, laid to a slope of 1 in 12 in a manner that top face shall conform to the finished level of PCC adjacent to the edging. PCC shall be laid in alternate bays (not exc. 2.5 meters length) and finished even and smooth without using extra cement. 6 mm wide joints shall be provided throughout the thickness of plinth protection in concrete bays at corners and turning points and also in between walling and plinth protection. All joints in bays, as well as between walling and the concrete in plinth protection shall be filled in with mastic filling comprising 1 part of heated bitumen 85/25 grade and 3 parts of sand (all by weight) complete all as specified and directed.

Dismantling plain or corrugated roof sheeting any gauge, thickness, including Naintal or similar pattern roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets, complete all as specified and directed.

M&L for 6mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face; fixed with screws to timber frame work in ceiling complete all as specified & directed.

M&L for 9mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work in wall panelling complete all as specified & directed.

Dismantling Unframed timber scantlings under 40 sq. cm in section as in fillets, rails, posts, rafters, purlins, etc. in any position complete all as specified and directed.

M&L 2nd class hard wood for Plain fillets exc 13 sq.cm but n.exc 25 sq.cm, rectangular or triangular in section, clean sawn, secured with nails or brads including applying two coats of synthetic enamel paint over and incl a coat of red oxide primer complete all as specified and directed by Engr-in-charge.

M&L 2nd class hard wood for Plain fillets n.exc 3 sq.cm, rectangular or triangular in section, clean sawn, secured with nails or brads including applying two coats of synthetic enamel paint over and incl a coat of red oxide primer complete all as specified and directed.

All as per item no-13 here-in-before, having cross-sectional area exc 6 sq.cm but n.exc 13 sq.cm but bull nosed, splayed, chamfered or rounded on one edge or face for corner, complete all as specified and directed.

Dismantling Unframed timber scantlings 40 Sq. cm and over in section and in any position complete all as specified and directed.

M&L for clean sawn 2nd class hard wood in scantling timber framed work fixed with screws/ nails complete all as specified and directed by Engr-in-charge.

Taking down shutters of any description area n exc 1 sqm each complete all as specified & directed.

Taking down shutters of any description area exc 1 sqm and n exc 2 sqm each complete all as specified & directed.

S&F 30 mm flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 300mm long aluminum anodised sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and incl minimum of 6 nos. of bolts and nuts ,four on bolt plate and two on staple, complete all as specified and directed.

S&F 100mm long Aluminum butt hinges of extruded aluminum alloy with galvanized mild steel hinge, pin anodized complete all as specified and directed.

S&F 150mm long aluminum anodised handle fabricated type complete all as specified and as directed by Engineer-In-Charge.

S&F 150mm long aluminum anodized barrel tower bolt of extruded section complete all as specified and directed by Engineer-In-Charge.

S&F Anodised aluminum window and ventilator shutters, fixed type without sash bar, aluminum section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc., incl 4 mm thick glass pane / GI wire cloth of 0.56 mm nominal dia in opening complete all as specified and directed.

Hacking out old broken glass (any thickness, size quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified & directed.

M&L for 5.5mm thick sheet glass in squares exceeding 0.50 Sqm in each pane with oil putty in complete all as specified & directed.

S&F in repair for galvanised M S Wire cloth of 0.56 mm nominal dia of wire and average width of aparture 1.18 mm fixed with tinned tack for galvanized wire staple complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L for rendering 15mm thick in cement plaster 1:4 on stone masonry surfaces or surface other than fair face of brickwork or concrete work on one side of lathing finishing even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying two coats of cement base paint over and including a coat of alkali resistant priming paint complete all as specified and directed.

M & L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote oil complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

M & L for cement concrete Type C2 1:3:6, (40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

S & F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-16 complete all as specified and directed.

S & F in replacement galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails including securing or tying at crossings with provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed.

M & L for preparation of new surfaces of steel of any description over 10cm in width or girth apply two coats of black Japan paint over and incl a coat of red oxide primer (in enbedded portion) complete all as specified and directed.

M & L for preparation of new surfaces of steel of any description over 10cm in width or girth apply two coats of synthetic enamel paint over and incl a coat of Red oxide primer complete all as specified and directed.

Taking down carefully copper/aluminium point wiring from existing points (light, fan, socket or power) alongwith compete fittings such as switches ,ceiling rose, pendent holder, light fitting & regulator etc. (Schedule of credit for each item to be given separately) including making good to the disturbed surfaces of wall, roof and floor etc. to match with the existing surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring using approved colour coding as per IS with using approved colour coding as per IS 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continuous earthing in & incl PVC Casing and caping with accessories having ISI mark fixed on wall surfaces / ceiling including provision of 2mm thick sheet metal terminal box with 3mm hylam laminated sheet on top for fixing switches sockets etc. all as specified for one light point/ fan /Bell point, etc., controlled by one switch complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 40 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the independent board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 40 here-in-before but controlled with one 3 pin socket outlet 15 Amp, independent board with cable 2.5 sqmm including provision of 1.5 sqmm single core multistanded PCV insulated copper conductor as earth conducting conductor complete all as per specified and directed by Engineer-in-Charge.

Supply and fixing of switch piano type 15 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge,

Supply and fixing of socket outlet 3 pin 15 Amp 2-in-one 230 Volt flush type complete all as specified and directed by Engineer -in-Charge.

Supply and fixing of socket outlet 3 pin 5 Amp 2-in-one 230 Volt flush type complete all as specified and directed by Engineer -in-Charge.

Supply and fixing of switch piano type 5 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge,

M&L Ceiling rose, 3 terminal with ISI mark all as specified and directed by Engr-In-Charge.

Supply and fixing surface & wall mounted LED 20W tube light fitting 4 feet with high quality material and design, extruded aluminium housing enhances safety. High quality PC diffuser, reliable and robust housing structure, maximize the endurance over the life time slim integrated design, easy to install efficacy 125 limen/ watt all accessories as specified and directed by Engg-in-Charge.

Supply & Fixing LED light fitting 1x9W / 10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

S & F in replacement sheet metal enclosure double door distribution board single pole and neutral, 8 way 240 volt with 200 amps rated bus bar complete with bus and neutral link complete all as specified and directed.

S&F in replacement MCB SPN 32Amp,10 KA 'C' curve, 240V, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement MCB SP 6 Amp to 32 Amp, 10 KA rating 240V, 'C' curve complete all as specified and directed by Engineer-in-Charge.

M&L in replacement for Earthing complete with GI steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI earth wire of 4 mm dia protected by GI protection pipe light grade of 40mm bore dia from mechanical injury, 20 mm medium grade for watering with funnel, including test point up to 7.5 meter from earth pit, adequate quantity of common salt, charcoal dust, chemical and connected to test point by means of bolts and nuts washers made out of GI all as shown in Electrical plate No 3 of SSR part I including necessary earthwork and excavation in any type of soil, PCC 1:2:4 type B1 chamber with 40mm thick RCC 1:2:4 type mix cover slab with 6mm dia MS bars at 100mm dia both ways with MS hook 6mm dia MS bars etc. complete all as specified and directed by Engr-in-charge. Note: 1. Suitable quantity of charcoal, common salt, funnel, GI pipe required for watering, pit & CI pit cover etc is deemed to be included in quoted rate and lead wire used beyond 7.5m from pit cover will be measured separately. 2. On testing after completion if the desired resistance is not obtained the earthing shall be re-done at no extra cost.

Supply, laying and testing in replacement XLPE cable PVC insulated, armoured heavy duty electric cable with aluminium stranded conductor, 1100 volts grade, with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire one twin core cable flat or circular of cross-sectional area 16 Sq mm 2 core as per IS specifications complete all as specified and directed by Engr-in-charge.

Schedule of Credit

H S ENTERPRISE (BID ID -3169997)

chankaya solutions (BID ID -3164033)