Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹13.1 CrAccepted-Finance 3RD FLOOR PLANT 11 ALTERNATE MOBILE NO 98749 32329 GITESH VERMA AIR CONDITIONER REFRIGERATOR VIKHROLI WEST MUMBAI MAHARASHTRA 400079 | MUMBAI SUBURBAN | MAHARASHTRA | 400079 | ₹13.1 Cr | L1 | Accepted-Finance Lowest rate found. |
| 2 | L2₹13.4 CrAccepted-Finance | ₹13.4 Cr | L2 | Accepted-Finance High rate found. |
| Sl No | Description | Qty | Unit | Anand Associates | GODREJ AND BOYCE MFG. CO . LTD |
|---|---|---|---|---|---|
| 1.00Civil works others | |||||
| 1.01 | Providing, supplying and placing of ANTI VIBRATION TABLE FOR BALANCE 600mmL x 600mm Dx 900mm H
The table consists of following parts:
Tubular frame - Completely modular type tubular frame, which carries the load of granite, kept on it. High-tension Pan head M6 Zinc black-coated screws (for better corrosion resistance) are used for the fastening. The material used is: 40 mm x 40 mm x 1.6 mm thick ERW tube and the overall load carrying capacity of tubular frame is 250 kgs of uniform distributed load.
Cover Panels – They are 0.8 mm thick CRCA MS sheet and pre-treated and epoxy powder coated for better corrosion resistance. The thickness of powder coat is 45-50 microns which passes the test of Salt Spray for 1000 Hours and having the Scratch Hardness of 3 Kgs.
Work Surface – granite
inner granite thickness- 115 mm
outer granite thickness -20 mm.
Inner granite dimensions: for 600W Table: 300Wx380D
Vibration Isolating Rubber pads - The objective of using these rubber pads is to absorb the pulsating vibrations coming from the floor. The pads are made up from combination of nitrite rubber, cork particles and cross-linked polyester fibre. This high-grade compound material possesses all the physical and mechanical properties required to minimize the dampening effect.
Levelling screws - The Tubular frame has the provision for 4 height adjusters or Levelling Screws that take care of all levelling aspects (Make as Per Selection of Architect Or Selection Of Higher Authority) | 13 | Nos | 5,16,452.3 ₹5.2 L | 5,04,803 ₹5.0 L |
| 1.02 | Providing supply, Installtion of PP/FRP Blower of Centrifugal Fan with Housing in PP Construction & suitable stand in MS Zinc Plating with Powder Coating.
Model No.: PP25-1014
Non FLP Motor: 1HP 1400 RPM
Inlet/Outlet Dia: 250mm
Impeller Dia: 315mm
Maximum CFM: 1100 @ 0 WCMM Static Pressure
Minimum CFM: 400 @ 35 WCMM Static Pressure
DB level: 70Motor
Description: IP55, 3 Phase, 440 Volt , 50 Hz.
Weather cover for motor
Anti-Vibration Pads & M10x100 pin type Anchor Fasteners
Blower Weather Cowl (FRP Outlet) & MS Stack Support with required Clamps PP25
10” (250mm) 100% Injection Molded PP Damper with Two Side Flange MODEL NO:DD/02 (Make as Per Selection of Architect Or Selection Of Higher Authority) | 8 | Nos | 4,63,664.64 ₹4.6 L | 4,53,206 ₹4.5 L |
| 1.03 | Providing supply, Installtion of PP/FRP Blower of Centrifugal Fan with Housing in PP Construction & suitable stand in MS Zinc Plating with Powder Coating.
Model No.: PP25-1014
Non FLP Motor: 1.5 HP 1400 RPM
Inlet/Outlet Dia: 250mm
Impeller Dia: 315mm
Maximum CFM: 1100 @ 0 WCMM Static Pressure
Minimum CFM: 400 @ 35 WCMM Static Pressure
DB level: 70Motor
Description: IP55, 3 Phase, 440 Volt , 50 Hz.
Weather cover for motor Anti-Vibration Pads & M10x100 pin type Anchor Fasteners
Blower Weather Cowl (FRP Outlet) & MS Stack Support with required Clamps PP25
10” (250mm) 100% Injection Molded PP Damper with Two Side Flange MODEL NO:DD/02 (Make as Per Selection of Architect Or Selection Of Higher Authority) | 1 | Nos | 61,283.08 ₹61,283.08 | 59,900.75 ₹59,900.75 |
| 1.04 | Providing Supply, Installtion of PP/FRP Blower of Centrifugal Fan with Housing in PP Construction & suitable stand in MS Zinc Plating with Powder Coating.
Model No.: PP35-2014
Non FLP Motor: 2 HP 1400 RPM
Inlet/Outlet Dia: 350mm
Impeller Dia: 400mm
Maximum CFM: 2550 @ 5 WCMM Static Pressure
Minimum CFM: 1175 @ 50 WCMM Static Pressure
DB level: 75
Motor make : IE2 (Non FLP), Crompton Greaves/Bharat Bijlee make whichever is available
DB Level: 85 Approx
Motor Description: IP55, 3 Phase, 440 Volt , 50 Hz.
Weather cover
Anti-Vibration Pads & M10x100 pin type Anchor Fasteners
Blower Weather Cowl (FRP Outlet) & MS Stack Support with required Clamps PP25
12” (300mm) 100% Injection Molded PP Damper with Two Side Flange MODEL NO:DD/02 (Make as Per Selection of Architect Or Selection Of Higher Authority) | 6 | Nos | 4,37,164.38 ₹4.4 L | 4,27,303.5 ₹4.3 L |
| 1.05 | Providing Supply, Installtion of PP/FRP Blower of Centrifugal Fan with Housing in PP Construction & suitable stand in MS Zinc Plating with Powder Coating.
Model No.: PP35MD-3014
Non FLP Motor: 3 HP 1400 RPM
Inlet/Outlet Dia: 350mm
Impeller Dia: 400mm
Maximum CFM: 4350 @ 10 WCMM Static Pressure
Minimum CFM: 1200 @ 70 WCMM Static Pressure
DB level: 75
Motor make : IE2 (Non FLP), Crompton Greaves/Bharat Bijlee make whichever is available
Motor Description: IP55, 3 Phase, 440 Volt , 50 Hz.
Weather cover for motor
Anti-Vibration Pads & M10x100 pin type Anchor Fasteners
Blower Weather Cowl (FRP Outlet) & MS Stack Support with required Clamps PP25
12” (300mm) 100% Injection Molded PP Damper with Two Side Flange MODEL NO:DD/02 .(Make as Per Selection of Architect Or Selection Of Higher Authority) | 17 | Nos | 12,87,447.4 ₹12.9 L | 12,58,407.15 ₹12.6 L |
| 1.06 | Providing Supply, Installtion of PP/FRP Blower of Centrifugal Fan with Housing in PP Construction & suitable stand in MS Zinc Plating with Powder Coating.
Model No.: PP35-5028
Non FLP Motor: 5 HP 2800 RPM
Inlet/Outlet Dia: 350mm
Impeller Dia: 400mm
Maximum CFM: 4850 @ 35 WCMM Static Pressure
Minimum CFM: 270 @ 210 WCMM Static Pressure
DB level: 100
Motor make : IE2 (Non FLP), Crompton Greaves/Bharat Bijlee make whichever is available
Motor Description: IP55, 3 Phase, 440 Volt , 50 Hz.
Weather cover for motor
Anti-Vibration Pads & M10x100 pin type Anchor Fasteners
Blower Weather Cowl (FRP Outlet) & MS Stack Support with required Clamps PP25
12” (300mm) 100% Injection Molded PP Damper with Two Side Flange MODEL NO:DD/02 (Make as Per Selection of Architect Or Selection Of Higher Authority) | 1 | Nos | 1,27,680 ₹1.3 L | 1,24,800 ₹1.2 L |
| 1.07 | Providing supply installation of Chemical Storage Base Cabinet (1000mm Wide x 1500 mm H ) with Ventilation , Storage cabinets are designed to safely store highly corrosive acids. With a full PP construction, the cabinets are completely protected from corrosion, making them the preferred choice in labs and workspaces dealing with aggressive chemicals. cabinet provides you with a storage solution that easily outperforms the metal and wooden storages.
All safety claims of this product are backed by third party certification for Chemical Spot Test for 49 chemicals listed in SEFA standards, the product must be 3rd party tested as per SEFA 8P and used across various industries. The cabinet has been designed to be fully ventilated ensuring air circulation and preventing a build-up of dangerous fumes within the cabinet. The shelves comprise of removable height adjustable collection trays that are leak-proof, enhancing the safety factor of the storage units.
Exhaust Provision: There is an air-duct at the back, inside the cabinet that effectively extracts fumes when connected to exhaust. Louvers are provided on the front doors to allow inward Low of fresh air.
Zero-Corrosion: Full Polypropylene Body, with no exposed metal hardware, ensures there is no corrosion
Closing mechanism: The cabinet has a latch to ensure proper shutting of the doors.
Removable & Height- Adjustable PP Trays as Shelves: the PP Collection Trays can be removed easily, and can be height-adjusted as required.
Load Bearing Capacity & Spill Containment: Each shelf can take up to 30 kgs (approx) of uniformly distributed load. The shelves are leak-proof and fully contain accidental spillages.
Locking Provision: The door has provision for using a padlock to safeguard the contents of the cabinet. (Make as Per Selection of Architect Or Selection Of Higher Authority) | 11 | Nos | 9,15,794.11 ₹9.2 L | 8,95,137.1 ₹9.0 L |
| 1.08 | Providing supply installation of CORNER SINK TABLE -Size :-1100mm L x 1100mm D x 900mm H
construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.
Dimensions: W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos
MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk •
Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.
Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch.
PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm.
Faucet - 3-way type faucet as per approved make
WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority) | 11 | Nos | 4,40,853.16 ₹4.4 L | 4,30,909.05 ₹4.3 L |
| 1.09 | Providing supply installation of CORNER SINK TABLE -Size :-1100mm L x 1100mm D x 900mm H with Eye wash
construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation.
Dimensions: W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos
MOC: MSCRCA: IS – 513 (1994)•Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk •
Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pretreatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating.
Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch.
PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make
DECK-MOUNTED EYE-WASH - Deck mounted drench hose units should have a single outlet head with a rubber protective collar and should deliver an aerated flow of water. The valve should be forged brass self-closing type with a stainless steel squeeze handle. Units should be furnished with a deck flange and an 8 ft. reinforced PVC hose
WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority) | 2 | Nos | 91,433.52 ₹91,433.52 | 89,371.1 ₹89,371.10 |
Tender Value
₹12.2 Cr
EMD Value
₹22.2 L
Closing Date
25 Mar 2026, 2:00 pmClosed
The Exe., Engg., PWD, WD-I, Daman.
O/o the Ex. Eng., P.W.D., 2nd floor Multi office complex, near Veg. Market, Moti Daman.
Interior and Furnishing Work of Government College Daman.
2026_DAMAN_4636_1
Tender Notice No.141/2025-26
Open Tender
Civil Works
90 days
Daman District.
Please refer Tender documents.
2 documents required · 2 mandatory
₹10,000
The Exe., Engg., PWD, WD-I, Daman.
₹22.2 L
The Exe., Engg., PWD, WD-I, Daman.
8 May 2026
28 Feb 2026
25 Mar 2026
28 Feb 2026
25 Mar 2026
28 Feb 2026
13 Mar 2026
Civil works others
Providing supply installation of WALL TABLE Size :-11630mm L x770mm D x 900mm H with PP sink and Eye wash Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=750/900 mm, D = 530mm, H = 875 mm Configurations: storage 750 W 2 Shutter + 1 Drawer - 7 Nos, 900 W 2 Shutter + 1 Drawer - 2 Nos , storage 750 W 2 Shutter - 4 Nos , sink units 750 w 2 shutter – 2 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL TRUNKING: Electrical trunking is made up of 0.8mm thick CRCA MS Sheet. Electrical provision for socket to be provided every 2 feet. ELECTRICAL ACCESSORIES (6/16 ASWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make - 2 Nos DECK-MOUNTED EYE-WASH - Deck mounted drench hose units should have a single outlet head with a rubber protective collar and should deliver an aerated flow of water. The valve should be forged brass self-closing type with a stainless steel squeeze handle. Units should be furnished with a deck flange and an 8 ft. reinforced PVC hose.- 2 Nos WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.
Providing supply installation of WALL TABLE Size :-12040mm L x770mm D x 900mm H , PP sink & Gas valves Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W= 750 W mm, D = 530mm, H = 875 mm Configurations: Storage - 750 W 1 Drawer + 2 Shutter - 8 Nos ,Storage - 750 W 1 Drawer + 2 Shutter - 7 Nos sink units 750 w 2 shutter – 1 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make - 1 Nos Gas Valves : 1 way - Gas Valve 180 degree Laboratory Push/Turn Gas Valve Fitting Deck Mounted With Pop - Up Indicator Disc For LPG gases. - 1 Nos WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.
Providing supply installation of WALL TABLE Size :12090mm L x770mm D x 750mm H with MDF Worktop with KBPT Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=450/750 mm, D = 530mm, H = 875/725 mm Configurations: Storage 450 W - 1 shutter - 10 Nos , Legspace 600 W - 10 Nos , Storage 750 W - 1 Drawer + 2 shutter - 1 Nos , Corner Leg space - 1 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. KBPT - keyboard tray to be provided in legspace - 20 Nos.along with cable manager ( grommet cut) ELECTRICAL TRUNKING: Electrical trunking is made up of 0.8mm thick CRCA MS Sheet. Electrical provision for socket to be provided every 2 feet. ELECTRICAL ACCESSORIES (SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. WORKTOP : The MDF worktop shall consist of a high-density industrial-grade Medium Density Fiberboard (MDF) sheet, preferably with a thickness of 18mm to 25mm for optimal strength, rigidity, and resistance to sagging, or a laminated, double-layered, 3/4-inch (approx. 19mm) construction for enhanced durability. The board must have a smooth, uniform texture, with exposed edges sealed or banded to prevent moisture ingress, as raw MDF degrades when wet. For heavy-duty use or increased impact resistance, a 1/4-inch hardboard or tempered masonite sacrificial top layer should be considered, which also conceals attachment points. The MDF top should be mechanically fastened to the metal understructure (minimum 1.5mm box section steel) using self-drilling, self-tapping, or wing-tip "Tek" screws inserted from underneath through pre-drilled holes in the frame to ensure a clean surface.
Providing supply installation of WALL TABLE Size :-3880mm L x770mm D x 900mm H WITH PP sink & Eye wash Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=750 mm, D = 530mm, H = 875 mm Configurations: Storage 750 W 2 Shutter + 1 Drawer - 3 Nos , sink units 750 w 2 shutter – 2 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL TRUNKING: Electrical trunking is made up of 0.8mm thick CRCA MS Sheet. Electrical provision for socket to be provided every 2 feet. ELECTRICAL ACCESSORIES (6/16 ASWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make - 2 Nos DECK-MOUNTED EYE-WASH - Deck mounted drench hose units should have a single outlet head with a rubber protective collar and should deliver an aerated flow of water. The valve should be forged brass self-closing type with a stainless steel squeeze handle. Units should be furnished with a deck flange and an 8 ft. reinforced PVC hose.- 1 Nos WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.
Providing supply installation of WALL TABLE Size :-4564mm L x770mm D x 900mm H WITH KBPT Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=450 mm, D = 530mm, H = 875/725 mm Configurations: Storage 450 W 1 Shutter + 1 Drawer - 3 Nos , Leg spaces 750W – 3 Nos , Corner Legspace 750 W - 1 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. KBPT - keyboard tray to be provided in legspace - 20 Nos.along with cable manager ( grommet cut) COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL TRUNKING: Electrical trunking is made up of 0.8mm thick CRCA MS Sheet. Electrical provision for socket to be provided every 2 feet. ELECTRICAL ACCESSORIES (SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.
Providing supply installation of WALL TABLE Size :4580mm L x770mm D x 900mm H Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=750 mm, D = 530mm, H = 875 mm Configurations: Storage 750 W 2 Shutter + 1 drawer - 3 Nos , Storage 750 W 2 Shutter - 3 Nos Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. ELECTRICAL TRUNKING: Electrical trunking is made up of 0.8mm thick CRCA MS Sheet. Electrical provision for socket to be provided every 2 feet. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. WORKTOP : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.
Providing ,Supplying and fixing of Confernece Table10 seater od sice MINGLE UNITIZED PLT_10 seater ST-3000 X 1150 X 740. with Laminate with Siam Teak color.Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Soft closing dual access flap provided for access to power supply and data cables.The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables(eg. HDMI,VGA-A,etc).
Providing ,Supplying Key Hanger Board for 30Keys Hanger Board Made fromgi steel material, it has 7 layered powder coated black finish, which is durable & long lasting.for Hanging Keys with openable able door with lock & keys The Size of this key storage box is – (l) 33 x (w) 5.5 x (h) 60.5 cm.Complete with installation as per direction of Engineer in charge.
Please Enable Macros to View BoQ information
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 27.58 MB
BOQ_4812.xls
BOQ • 13.07 MB
Download all tender documents and submit your bid