GE 861EWS-60/2021-2022

Amount

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc

Demolition of brick or stone masonry built in cement mortar including all necessary arches quoins etc.

Demolition of cement concrete (unreinforced in ground floors & pavings n.exc 15 cm thick (below or above ground level)

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store.

Taking down chowkhat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each

Taking down chowkhats or frames not exc. 1.5 Sqm but with shutters (without taking off shutters from the frames)

Taking down shutter(any description) area exceeding 1 sqm but not exceeding 2 sqm each.

Taking down shutter of any description n/exc 1.00 sqm each

M&L for brick work with sub class ‘B’ brick straight or curved on plan exceeding 6m mean radius in CM 1:4 complete all as specified and directed

M&L rendering 15mm thick cement plaster on other than fair faces of brick work surfaces in cement mortar (1:6) complete all as specified and directed

M&L for rendering 15mm thick on fair face of brick work or concrete surface in CM 1:4 finished even and smooth .without using extra cement complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B0 using 12.5 mm graded aggregate as in floor to receive floor finishes etc. all as specified.

M&L Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:6) laying floor finish complete all as specified and directed.

M&L Glazed ceramic tiles,joint free, Premium class I grade, coloured of size 350mm x250mmx7mm/ 450mm x350mmx7mm as in vertical surfaces such as skirting/dado etc., set and jointed in neat cement slurry and pointed with white or coloured cement, laid over and including 10mm thick rendering in cement mortar 1:4 on surfaces of walls complete, all as specified.

M&L 2nd class hard wood, plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified.

S&F 2nd class hard wood (Sal/Hollock) 35 mm thick paneled shutter (any number of panels )with panels of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified.

Supply and fixed 35mm thick 2nd class hard wood(Sal/Hollock) glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc (internal sash bars) edges of framing plane, chamfered or rounded fitted and mitered beads for securing glass etc size of members as specified in SSR Part-I Section 8 clause 8.24(a) complete all as specified.

S&F for 30 mm thick 2nd class hard wood glazed and skeleton windows/ventilators shutters open rebated and prepared to receive glass, gauge etc , divide into square with plain chamfered or rounded, mitered and rebated sash bars any numbers , provided with stiles and rails as specified in SSR part I section 8 clause 8.24 (b) complete all as specified.

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelam PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and gap insert for top rail and bottom rail paneling of plain colour PVC to sheet to be fitted in the MS frame welded / sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

S&F aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed complete all as specified and directed.

S&F aluminium anodised barrel tower bolts extruded section of size 200 mm long , all as specified and directed

S&F aluminium anodised barrel tower bolts extruded section of size 150 mm long , all as specified and directed

S&F aluminium handle extruded fabricate type anodised of size 150 mm complete all as spd and directed.

S&F butt hinges medium weight MS cold rolled 100mm long complete all as specified and directed.

S&F butt hinges medium weight MS cold rolled 75mm long complete all as specified and directed.

S&F MS helical door spring including roller & roller plate complete 300 mm size complete all as specified & directed.

S&F 150 mm long floor door stopper of alu alloy body and tongue, anodised with hard drawn steel spring all as specified and directed.

M&L 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane including hacking out old glass panes all as spd.

M&L 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane all as spd.

M&L 4mm thick figured glass pin headed type and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane including hacking out old glass panes all as spd.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm all as specified and directed.

S&F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type B2 (using 40 mm graded aggregate ) as in sub for receiving floor finishes etc all as specified and directed.

M&L for chequerd cement concrete tiles 30cm x30cmx25mm thick with grey cement and pigment , set , jointed and pointed in neat cement slurry in floors laid over 15 mm thick screed bed in CM 1:6 all as spd & directed.

Dismantling water storage tanks of any description but exc 250 and n. exc 500 liters capacity and removing from site complete all as specified.

S&F for Rotational moulded polyethylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball complete all as specified

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connections of flush pipe to squat pattern closet including lime concrete bedding and all joint making good to the floor all as specified.

S & F in repair vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (min), with grating and union for discharge pipe including flushing system, flush pipe & waste pipe) all as specified & directed.

S&F in repairs floor stainless steel gratings , 125mm dia

S&F in repair PVC valve less 10 litres capacity symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engr-in -Charge.

S&F in repair Vitreous china wash hand basin, with pedestal Vitreous china white, flat back, size 550 x 400 mm with brackets, including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed. (Including 15mm bore CP pillar tap, waste coupling and 32mm dia PVC waste pipe)

S&F in repairs 15 mm size PVC connection with PTMT nuts of 600 mm long.

S&F in repairs swivel shower of PTMT any colour with arm, 195 mm long with bend of 45 degree with flange (both min wt 80 gms )

S&F 110 PVC sanitary connection for WC complete all as specified.

S&F cast iron Nahani trap 75 mm dia including jointing to pipe complete.

S&F in repairs 15 mm bore fancy type CP bib taps cast copper alloy with crutch or butterfly nuts , handle, screwed down for iron pipe.

S&F & repairs, 15 mm bore CP stop/angle valve cast copper alloy screwed down , high pressure with crutch or butterfly handle fancy type complete.

S&F & repairs, 15 mm bore CP with long shank and cup (concealed type) cast copper alloy screwed down , high pressure fancy type complete.

Taking up or down 15mm dia GI tubing and connections including cleaning for refixing or removal to store complete all as specified.

Taking up or down 20 mm dia GI tubing and connections including cleaning for refixing or removal to store complete all as specified.

S&F 15 mm bore GI tubing med grade galvanised with all ftgs and fixed complete to walls & floors etc

S&F 20 mm bore GI tubing med grade galvanised with all ftgs and fixed complete to walls & floors etc

S&F in repairs tubular towel rail, 20mm dia, D type, 60 cm long between flanges.

S&F in repair vitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and fixing to flushing cistern, brackets, flushing pipe etc complete all as specified.

S&F in repair 15 mm bore brass CP mixer for mixing hot and cold water screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes

S&F in repair Ball valve high pressure of PTMT with epoxy coated aluminium rod and high-density plastic ball screwed for 20mm dia iron pipe and fixed (minimum weight 15mm-142gms/20mm 210gms/25mm 455gms/40mm 690gms.

S&F in repair pillar taps 15mm bore of cast copper alloy with fancy type capstan heads, chromium plated screwed down high pressure for iron pipe and fixed in repair (Minimum weight 15mm-90gms/20mm- 125gms).

S&Fin repair bib taps 15mm bore of standard PTMT any colour high pressure screwed for iron pipe and fixed in repair (Minimum weight 15mm-90gms/20mm- 125gms).

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed.

S&F in repairs 75mm PVC (SWR) pipes single socketed, in any length jointed, fixed on walls/floor

S&F in repairs 110mm PVC (SWR) pipes single socketed, in any length jointed, fixed on walls/floor

S&F PVC (SWR) bends 75mm dia

S&F PVC (SWR) bends 110mm dia .

S&F 110mm PVC (SWR) vent cowl

S&F 75mm PVC (SWR) vent cowl

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs including cover fillets etc complete all as specified.

S&F for anodised aluminium snap grid of size 605 x605 mm frame work for false ceiling including straining with GI wire 4 mm thick all as specified.

S&F for 10 mm thick PVC insulation panels with EPS stuck to 1 mm thick plain PVC sheet suitably placed in false ceiling grid made of aluminum GI/MS as per specification and drawing complete all as specified.

S&F for solid PVC wall paneling decorative type consisting of 5 mm thick plain colour PVC pre-laminated sheet inclusive of solvent cement and and fixing at site on PVC frame complete all as specified.

S&F for 5 mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame complete all as specified.

S&F for 9 mm thick veneered decorative plywood , grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screw to timber frame on wall and ceiling etc complete all as specified and directed.

S&F 2nd class soft wood plain fillets square rectangular or triangular in section clean sawn fixed with nails Sectional area exc 06 but not exc 13 sqcm complete all as specified

S&F in repairs 40mm thick , 2nd class hardwood planks , planed one side with butt joints and fixed with nails fixed in any situation complete all as specified.

M&L in repairs for weather boarding in 2nd class hardwood clean swan , plain , 20 mm thick or feather edges , 15 mm to 20 mm thick and fixed with 30 mm laps joints complete all as specified.

S&F in repairs timber frame in second class hard wood as in scantling etc complete all as specified.

Dismantling plain or corrugated steel sheeting any gauge, thickness including roof covering etc complete all as specified.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers in roof etc.with grade of zinc coating 275 complete all as specified.

S&F 0.80mm thick plain galvanised mild steel sheeting in ridges, hips valley gutters, drip and straight flashings (length and girth as fixed)with grade of zinc coating 275 complete all as specified and directed.

Dismantling structural steel work including doors, gates, etc

S&F for Hand rails, half round or other stock section , nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe 290 gde E 165 complete all as specified and directed.

S&F framed work such as grills, grating etc with guard bars,feamed guard bars, hold fasts,, railing, framed work of water tanks and similar work confirming to Fe-290 gde-E165 complete all as specified and directed.

M &L for preparing plastered or un plastered new surface of walls and applying two coats of Cement base paint on walls(Externally) over priming with alkali resistant priming paint on walls all as specified.

M&L for applying 3 mm thick wall care putty on wall including preparation new surfaces plastered or unplastered surfaces applying two coats of oil bound distemper over a coat of chalk primer on newly plastered surfaces of wall

M&L for two coats of synthetic enamel paint on new wooden surfaces over coat of pink primer to new surfaces including preparation of surfaces, over 10cm width or girth complete all as specified.

M&L for two coats of synthetic enamel paint on new steel surfaces over coat of red-oxide primer including preparation of surfaces, over 10cm width or girth including roof painting complete all as specified and directed.

M &L for preparing plastered or un plastered new surface of walls and applying three coats of white wash on walls complete all as specified.

M&L for applying one coat of white wash on old plastered surfaces of wall including preparation of old surfaces complete all as specified.

S&F Plain mild steel wire, galvanised class 3 in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc. dia of wire 2.50mm all as specified.

M&L for applying one coat of white wash to old treated plastered or un-plastered surfaces of ceiling including preparation of surface complete all as specified and directed by the Engineer-in-Charge.

M&L for applying one coat of cement base paint to old treated plastered or un-plastered surfaces of wall including preparation of surface complete all as specified and directed by the Engineer-in-Charge.

M&L for applying one coat of oil bound distemper to old treated surfaces of wall including preparation of surface complete all as specified and directed by the Engineer-in-Charge.

M&L for complete removal of existing treament on old plastered surfaces and applying two coats of oil bound distemper over one coat of alkaline resistant primer over chalk whiting complete all as specified.

M&L for applying one coat of synthetic enamel paint to old painted wooden surfaces of any description, not oterwise described, over 10 cm width or girth including preparaton of surfaces all as specified and direcet by the Engineer-in-Charge.

M&L for applying one coat of synthetic enamel paint to old painted steel surfaces of any description, not oterwise described, over 10 cm width or girth including preparaton of surfaces all as specified and directed by the Engineer-in-Charge.

M&L for preparation of old decorated CGI Sheet surfaces of any descrption not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (in camouflage pattern) complete all as specified and as directed.

M&L for writing of letters of figures (block, roman , Italic or Indian), not exceeding 30 cm high, with thick synthetic enamel paint ( of approved tint) all as specified and as directed by the Engineer-in-Charge.

Taking down old unsv DB and taken as credit including supply and fix sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification.

Taking down old unsv DB and taken as credit including supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Taking down old unsv DB and taken as credit including supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Taking down old unsv DB and taken as credit including supply and fixing MCCB Distribution board, TP&N , vertical , double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link,415 Volts 4 way fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete including 4 Pole V-Tec MCCB of 100 A rating & 16kA breaking capacity, MCCB pre-fitted at factory all as specified and directed.

Taking down old unsv DB and taken as credit including supply and fix MCCB Distribution board, TP&N , vertical , double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link,415 Volts 8 way fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete including 4 Pole V-Tec MCCB of 100 A rating & 16kA breaking capacity, MCCB pre-fitted at factory all as specified and directed.

M&L in replacement MCB single pole 240 volts 6 to 32 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification complete all as specified and directed

M&L in replacement MCB single pole and neutral 240 volts 6 to 32 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification complete all as specified and directed

M&L in replacement MCB single pole and neutral 240 volts 40 to 63 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification complete all as specified and directed

M&L in replacement MCB Four pole 415 volts, 40 amps 'C' Curve 10 kA Capacity complete all as specified and directed

M&L in replacement MCCB four pole , 415 Volt, 100 Amps,25 KA , adjustable thermal & fixed magnetic setting complete all as specified and directed.

M&L in replacement MCCB four pole , 415 Volt, 125 Amps,25 KA , adjustable thermal & fixed magnetic setting complete all as specified and directed.

M&L in replacement MCCB four pole , 415 Volt, 160 Amps,25 KA , adjustable thermal & fixed magnetic setting complete all as specified and directed.

Supply and fixing in repair Automatic source change over with current limiter 30/20A single phase ACCL complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement off load change over switch on load 415 volts TPN in sheet metal enclosure with side handle of capacity 63Amps.

Supply and fixing in replacement off load change over switch on load 415 volts TPN in sheet metal enclosure with side handle of capacity 100Amps.

Supply and fixing in replacement off load change over switch on load 415 volts TPN in sheet metal enclosure with side handle of capacity 200Amps.

Dismantling the old unserviceable main switch and taken as credit including supply and fix new Double break Switch fuse Unit with 03 Nos HBC fuses conforms to IS/IEC 60947-1&3 metal clad Triple pole and neutral link, 415 volt 100 Amps HRC type all as directed. Make: Standard Cat Part No: ISFNTW4100 or equivalent in Havells/ Legrand

Supply and replacement of metal clad socket single pole and neutral enclosure with a two pin and earth plug top and socket complete with one single pole MCB 230 Volts 20/32 Amps all as specified and as directed.

Supply and fixing in repair Automatic source change over with current limiter 32A 3PHASE ACCL complete all as specified and directed by Engr-in-Charge. Make Havells OR Equivalent in Indoasian/L&T/legrand

Taking down carefully aluminum/copper point wiring (light fan socket or power) complete with fitting such as switches, tube lights, ceiling rose, pendants, regulators, MCB DB, MCB'S, Main switch from control board and making good disturbed surfaces of walls, floor to match with existing specification complete and all as specified keeping aside regulators/ light fitting/ MCBs serviceable/ unserviceable items for reuse with in the same bldg or deposited to MES store yard

Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and including PVC casing and capping/Conduit medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size or PVC Gang Box all as directed by Engr in Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified.

All as per srl item No119 here in above but for one 3 pin 5A socket outlet independent controlled by one switch.

All as per srl item No119 here in above but for one 5A socket outlet on the same board controlled by one switch.

All as per srl item No119 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead.

M&L in replacement submain wiring with two single core PVC insulated flexible copper conductor cable of size 4 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 4 Sqmm as earth lead in & including concealed PVC casing capping medium grade 2mm thickness ISI marked or cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification incl taking down old unsv complete all as required at site or directed by Engr-in- charge.

M&L in replacement submain wiring with two single core PVC insulated flexible copper conductor cable of size 6 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 6 Sqmm as earth lead in & including concealed PVC casing capping medium grade 2mm thickness ISI marked cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification incl taking down old unsv complete all as required at site or directed by Engr-in- charge.

M&L (in repair/replacement ) Switch piano flush button single pole one way 5 amps 240 volts

M&L (in repair/replacement ) Switch Socket combination, 6 pin 5 and 15 amps multi purpose 2 in 01 flush type, 230 volts

M&L (in repair/replacement ) Switch Socket combination 2 in 1, 5 Amps flush type, 230 volts

M&L (in repair/replacement ) Socket 2 in 1, 5 Amps flush type, 230 volts

M&L (in repair/replacement ) Socket 5/15 amps flush type, 230 volts.

M&L (in repair/replacement ) Ceiling rose surface Bakelite 2 to 3 terminals

Supply and fixing (in repair/replacement ) fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically all as required at site or directed by Engineer-in-charge.

S & F in repair Lamp holder insulated body with back plate for batten fittings,

S&F (in repair/replacement ) bell push flush type 6 Amps 240 Volt complete all as specified and directed.

S&F(in repair/replacement ) bell/buzzer AC 230 volts single pole complete all as specified and directed

Supply and fixing in repair Plug top 3 pin 15 amps 230 volts .

Supply and fixing in repair Plug top 3 pin 5 amps 230 volts Make :Cone /SSK/Anchor/Leader.

Supply & fixing in replacment Rigid non-metallic PVC conduit of size 25 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc

Supply and fix in replacement cable PVC FRLS insulated unsheathed with flexible multistranded copper conductor of size 1.5 Sqmm 1100 Volts grade as per site requirement of existing colour coding adopted .

Supply and fix in replacement cable PVC FRLS insulated unsheathed with flexible multistranded copper conductor of size 2.5 Sqmm 1100 Volts grade as per site requirement of existing colour coding adopted .

Supply and laying in replacement 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed twin core 4 sq. mm nominal cross section in service connections

Supply and laying in replacement 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed twin core 6 sq. mm nominal cross section in service connections

Supply and laying in replacement 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed twin core 10 sq. mm nominal cross section in service connections

Supply and laying in replacement 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed twin core 16 sq. mm nominal cross section in service connections

S & F in replacement decorative box type mirror light LED 8W fixture with in built electronic driver complete with all accessories prewired and connecting electrically to ceiling rose using PVC FRLS insulated and overall sheathed cable Make-Havells Cat Part No LUMILINEBS9WLED830SPCWH or equivalent in /Philips/Surya

Supply and fixing in replacement Wall mounted LED Batten, extruded Aluminium heat sink provided for efficient heat dissipation & integrated electronic driver of Lamp type: 18W LED life time of 30000* hours including lamp all as specified and as directed. Make: Philips, Cat Part No: TMC 501 p 1 X T-LED 22W P3241 & ESSENTIAL LED TUBE 1200 MM 18W865 T8 AP 1 or equivalent /Havells/C&S

Supply and fixing in replacment Slim surface mounted 18 Watt LED panel ( 6500 K) with premium diffuser to ensure glare free & even light distribution with necessary connection of suitable twisted copper flexible wire complete all as specifed and directed . Make : Havells cat Part No LHEAAHP7IL1W018/ Philips/ Bajaj

Supply and fixing in replacement Decorative wall light fixture made up of Polycarbonate, suitable for 9 W retrofit LED lamp B22 base including 9 watt LED lamp with necessary connection of suitable twisted copper flexible wire complete all as specifed and directed . Make : Havells cat Part NoLHDL02160099/ Philips/ Bajaj

Supply and fixing in replacement Efficient LED 36Watt (neutral white) recessed mounting 2x2 luminaire to enhance the delight of occupants with comfortable experience through its classic design and glare free illumination. Deep drawn CRCA housing with seamless front frame with flat non-yellowish diffuser with minimum 70 % lumen maintenance, CRI should be greater than 80, Electronic Driver should be in-built , power factor >0.9 with THD <10%. with necessary connection of suitable size of flexible copper cable complete all as specified and directed . Make : Bajaj Cat Part No BZRSQL 36W GZ1 NW or equivalent in Havells /Philips

Supply and fixing in replacement recessed Square shaped non integral downlighter 18Watt LED ( warm white) for soft down lighting made up with polycarbonate body for better heat disspiation with high efficient constant current driver.this comes with pre assembled SS Clips for easy installation with necessary connection of suitable size of flexible copper cable complete all as specified and directed . Make : Bajaj Cat Part No BPSLR 18W WW PRO SQ or equivalent in Havells /Philips

Supply and fixing in replacement Efficient LED 36 watt surface 2x2 luminaire to enhance the delight of occupants with comfortable experience through its classic design & glare free soft illumination. Deep drawn CRCA housing with seamless front frame with flat non-yellowish diffuser with minimum 70 % lumen maintenance, CRI should be greater than 80, Electronic Driver should be in-built , power factor >0.9 with THD <10%. with necessary connection of suitable size of flexible copper cable complete all as specified and directed . Make : Bajaj Cat Part No BZSSQL 36W LED WH i or equivalent in Havells /Philips

Supply and fixing in replacement LED 25 Watt (WW) post top in spherical shape polycarbonate diffuser & IP 65 protection,electronic Driver should be in-built , power factor >0.9 with THD <10%. with necessary connection of suitable size of flexible copper cable complete all as specified and directed . Make : Bajaj Cat Part No BLPTSP 25W LED WW or equivalent in Havells /Philips

Supply and fixing in replacemnet LED Bulk Head light fitting ,System consumption should be between 6-10 Watt. Similar to Philips Cat No : WT202W LED 6S NW PSU S2 PC or Havells cat part No RUGBYNE ONFT 10W LED 760 SSYMBOPC

Material & labour for repair of earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based onSSR rates adjusted (-)14.5%(Minus). (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

Javeed And Co

M/S LATIF AHMAD BABA CONSTRUCTION

M/s Pall Constructions

FG CONSTRUCTION