REPAIR/ MAINT TO ROOF, WATER TANKS, CLEANING OF EXISTING SEWAGE SYSTEM AND CERTAIN E/M WORKS AT AF STATION DADRI AND AOR OF GE (AF) FARIDABAD

Amount

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

M&L for RCC 1:2;4 B0 (using of 12.5 mm Stone Aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and chajjas complete all as specified and directed by Engineer-in-Charge.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge.

M&L for 10 mm dia and over TMT bar cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends binding with MS wire n.exc 0.9mm or with securing clips etc complete all as specified and directed by Engineer-in-Charge.

M&L for 6 to 8 mm dia TMT bar cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends binding with MS wire n.exc 0.9mm or with securing clips etc complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster from brick or stone masonry or concrete surfaces and hacking for key and scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in CM 1:4 on stone/brick masonary or surface other than fair face of brick works etc or similar surfaces complete all as specified and directed by Engineer-in-Charge.

M&L 15 mm thick rendering in cm 1:6 on brick surfaces or concrete surfaces finished even and smooth without using extra cement incl mixing of water proofing liquid of Dr. fixit as per manufactrer instruction complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10mm thick in CM 1:3 on concrete surface in ceillings etc including with mixing of water proofing liquid of Dr. fixit as per manufactrer instruction complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint on walls over a coat of alkali resistant priming paint complete all as specified and directed by Engineer-in-Charge.

M&L two coat of oil bound distemper after 3mm Birla/JK wall care putty on new plastered surfaces including necessary prepararion complete all as specified and directed by Engineer-in-Charge.

M&L three coat of white wash on new surfaces on ceiling including necessary prepararion complete all as specified and as directed by Engr-in-Charge..

Taking down existing water proofing treament any nos of layers and of any description, incl.demolition and taking off PCC padding/plaster on RCC slab,also including removing of bitument coating to show the concrete surface to its true colour and roughening etc and also removing the debris outside the MOD land complete all as specified and directed by Engineer-in-Charge.

Taking down existing mud puska any nos of layers and of any description, including removing of the debrisoutside the MOD Land up to distance 250 mtr complete all as specified and directed by Engineer-in-Charge.

Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 including macthing existing surfaces complete all as specified and directed by Engineer-in-Charge.

M&L Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) on roof padding avg. thicknessof 40mm in slope finished even and fair complete all as specified and directed by Engineer-in-Charge.

M & L for 20 mm thick Screed bed in cement mortar 1:3 mixed with integral water proofing compound @ 3% by weight of cement complete all as specified and directed by Engineer-in-Charge.

M & L for laying APP modified membarane with non woven polyester reinforcement mat (concrete core) not less than 3 mm thick & not less than 3.5 kg /sqm, the over the lap otching shall be 100 mm on length side & 100 mm on widthe side over a tack coat of Industrial bitumen of 1.20 kg / Sqm over Bituminious based primer IS No. 3383@ 250 gms/sqm including apply of Aluminium colour synthetic enamel paint @ 200 gms/sqm all as per manufacture's instruction complete all as specified and directed by Engineer-in-Charge. Note: Supply only integral water proofing compound shall be measured and paid separately.

Supply only integral water proofing liquid ( ISI marked) complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel water tubing and connection incl cleaning for refixing or removal to stores for following bore complete all as specified and directed by Engineer-in-Charge :- (a) 15mm

All as per item No 20 above but 20mm complete all as specified and directed by Engineer-in-Charge

Refixing old steel tubing and connections in new or old position on wall, ceiling, floor etc of 15 mm dia complete all as specified and directed by Engineer-in-Charge

Refixing old steel tubing and connections in new or old position on wall, ceiling, floor etc of 20 mm dia complete all as specified and directed by Engineer-in-Charge

S&F GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floor in following bore of tube complete all as specified and directed by Engineer-in-Charge :- (a) 15mm

All as per item No 24 above but 20mm complete all as specified and directed by Engineer-in-Charge

S&F in repair 20 MM Gun-metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed in repair and complete all as specified and directed by Engineer-in-Charge

S& Fix in repair 15 mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair and complete all as specified and directed by Engineer-in-Charge

S&F in repair 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair and complete all as specified and directed by Engineer-in-Charge

S&F in repair rotational moulded polyethylene water storage tanks (cylinderical, vertical with closed top) of 1000 Ltrs capacity hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge

S&F rotational moulded polyethylene water storage tanks (cylinderical, vertical with closed top) of 500 Ltrs capacity hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge

Cleaning and removal all scale and dirt, etc, from tanks and mouth of circulating pipes, etc exc 250 & n.exc500 litres capacity including to be write the date of cleaning with synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Cleaning and removal all scale and dirt ,etc ,from tanks and mouth of circulating pipes ,etc exc 500 & n.exc 1000 litres capacity including to be write the date of cleaning with synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Demolition & breaking up drain pipes (salt glazed stone ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 100 mm complete all as specified and directed by Engineer-in-Charge

All as per item No 33 above but bore of pipe 150 mm complete all as specified and directed by Engineer-in-Charge

All as per item No 33 above but bore of pipe 200 mm complete all as specified and directed by Engineer-in-Charge

M&L 100 mm internal dia salt glazed stone ware drain pipes laid in trenches and jointed complete all as specified and directed by Engineer-in-Charge

All as per item No 36 above but bore of pipe 150 mm complete all as specified and directed by Engineer-in-Charge

All as per item No 36 above but bore of pipe 200 mm complete all as specified and directed by Engineer-in-Charge

S & F in repair PVC 110 mm (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamps and for sewage line complete all as specified and directed by Engineer-in-Charge

S & F in repair PVC 110 mm (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge

S & F in repair PVC (SWR), junction single, (Single T) equal or unequal 110 mm complete all as specified and directed by Engineer-in-Charge

M&L concrete bed to 100 mm bore drain pipes in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregates including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engineer-in-Charge

All as per item No 42 above but bore of pipe 150 mm complete all as specified and directed by Engineer-in-Charge

All as per item No 42 above but bore of pipe 200 mm complete all as specified and directed by Engineer-in-Charge

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50 m in depth for manholes & sewage lines and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge

Demolition of brick work built in cement mortar of any description complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete of any description and in any position as in bed of drain pipes etc complete all as specified and directed by Engineer-in-Charge

M&L cement concrete type C-2 1:3:6 ( 40 mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge

M & L for brick work with sub class 'B' Bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 as in manholes and drain complete all as specified and directed by Engineer-in-Charge

M&L for providing cement concrete 1:2:4, type B1, using 20 mm graded stone aggregates as in coping complete all as specified and directed by Engineer-in-Charge

M&L PCC 1:2:4 type B2 as in surface channels and drains & benching of manholes and finishing even and smooth with out using extra cement complete all as specified and directed by Engineer-in-Charge

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed by Engineer-in-Charge

Removing excavated materials to a distance not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed by Engineer-in-Charge

Cutting into existing manholes for connecting new drains, making good to pipes and rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required, Internal dia of pipe 150mm complete all as specified and directed by Engineer-in-Charge

All as per item No 54 above but bore of pipe 100 mm complete all as specified and directed by Engineer-in-Charge

All as per item No 54 above but bore of pipe 200 mm complete all as specified and directed by Engineer-in-Charge

S&F in repairs cast iron Nahani trap with grating including jointing to waste pipe, fixed in cement concrete 1:2:4, type B-1, using 20 mm graded stone aggregate, dia of outlet 100 mm complete all as specified and directed by Engineer-in-Charge

S&F in repairs for Vitreous China squatting pan,"Orissa" pattern,size 580 X440 mm white,withintegral foot rests (excluding flushing cistern and flush pipe) including connection to flushing pipe anti syphonage pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repair vitreous China wash down water closet (EWC) pedestal pattern coloured incl P or ‘S’ trap coloured ,seat cover & cement concrete bedding complete all as specified and directed by Engineer-in-Charge

S&F PVC valveless,symphonic action type,flushing cistern ,low level white,with inlet,ball valve,float and handle including brackets of 10 ltrs complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC flush bend 32mm dia with two Nos check nuts for conencting low level flushing cistern to European type water closet or India type water closet incl cement joint complete all as specified and directed by Engineer-in-Charge

Dismantling floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge

M&L for coloured printed non skid tiles area of each tile exceeding exc 0.06 sqm but n.exc 0.11 sqm in floors etc set and jointed with neat cement slurry pointed with colour cement to match the floor, and including 15 mm thick screed bed cement mortar in CM 1:4 and including the chipping of the existing PCC floor complete all as specified and directed by Engineer-in-Charge

M&L for digital glazed ceramic tiles coloured size 300 x 200 x 7mm thick as on vertical surfaces, of walls as in skirting, dado etc set and jointed in neat cement slurry & pointed with coloured cement to match complete all as specified and directed by Engineer-in-Charge

Dismantling of stone slabs & tiles of any description or thickness (except ceramic tiles) in floors, aprons etc laid bedded & pointed in any mortar complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete unreinforced in groundfloors and pavings not exc 15cm thickness below or above ground level etc complete all as specified and directed by Engineer-in-Charge

M&L 75 mm thick PCC 1:4:8 type D-2 (using 40mm grade stone aggregate) as in Sub floors,Sub bases ,flooring etc complete all as specified and directed by Engineer-in-Charge

M&L cement concrete 75 mm thick type C-2 1:3:6 ( 40 mm graded agg ) as in plinth protection etc complete all as specified and directed by Engineer-in-Charge

M & L for Rubber moulded Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick set , jointed and pointed in neat cement slurry in floors with gray cement and pigment with screed bed 15 mm CM 1:6 complete all as specified and directed by Engineer-in-Charge

M & L for Machine pressed precast concrete interlocking paver block any shape and size with grey cement and coloured pigment confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade over 25mm thick coarse sand complete all as specified and directed by Engineer-in-Charge

M&L for Sand filling under floors or in foundation including watering and consolidating complete all as specified and directed by Engineer-in-Charge

Providing, precast cement concrete1:2:4 type B1 (20 mm graded aggregate) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc. and setting in mortar complete with joints to match complete all as specified and directed by Engineer-in-Charge

Dismantling wrought iron or mild steel / structural steel of any description not otherwise provided complete all as specified and directed by Engineer-in-Charge

Cleaning of pipe drains by jet mechine 100mm internal dia drain pipe upto 1.50 m in depth and removal of sludge/silt/liquid/mud and sand (in foul position) etc out side the MOD land including testing of drains by filling the pipes with water complete all as specified and directed by Engineer-in-Charge

All as per item No 74 above but cleaning of 150mm internal dia drain pipe not exceeding 1.5m in depth complete all as specified and directed by Engineer-in-Charge

Cleaning of manhole upto 1 m depth and removal of sludge silt/liquid/mud/sand/water etc in foul position to out side the MOD land complete all as specified and directed by the Engineer-in-Charge.

All as per item No 76 above but exceeding 1m and not exceeding 2m in depth complete all as specified and directed by Engineer-in-Charge

Dewatering/desilting of septic tanks,soak wells etc cleaning of all sludge,silt residue of both organic and inorganice nature by manual labour or mechnical scrappers etc and disposal of the same out side the defence land incl dumping the material to any depth complete all as specified and directed by Engineer-in-Charge

Taking down carefully aluminium point wiring/sub main wiring light, fan socket or power complete fitting such as switches, ceiling rose, fan regulator, socket including light fitting etc complete with MS conduit and T/W battern and depositing to MES store yard complete all as specified and directed by Engineer-in-Charge

M&L for Re wring with Modular /single core PVC insulated unsheathed 1100 volt grade cable with multistranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit / cassing capping / concelled as per ground requirement medium duty ISI marked not less than 20mm dia, fixed in wall, on roof with GI saddles GI screws, rawal plugs (concealed conduit in wall wiring) with all fittings including Tee, junction boxes and provision of pressed steel terminal box of suitable size with 3 mm thick hylam laminated white sheet cover for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC insulated unsheathed 1100 volts grade cable with multistranded coper conductor of size 1.5 Sq mm (Nominal area) complete all as specified and directed by Engineer-in-Charge

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade cable with multistranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, fixed in wall, on roof with GI saddles GI screws, rawal plugs (concealed conduit in wall wiring) with all fittings including Tee, junction boxes and provision of pressed steel terminal box of suitable size with 3 mm thick hylam laminated white sheet cover for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC insulated unsheathed 1100 volts grade cable with multistranded coper conductor of size 1.5 Sq mm (Nominal area) complete all as specified and directed by Engineer-in-Charge for following (Color coding to be followed) :- (a) One light/fan point controlled by one switch.

All as per item as per item No 81 but One socket point on same board with other switches complete all as specified and directed by Engr -in- Charge.

All as per item No 81 above but with One 3 pin 5 Amps socket outlet independent with cables 1.5 sqmm size complete all as specified and directed by Engineer-in-Charge

All same as per item No 81 above but with One bell/buzzer point controlled by one bell push complete all as specified and directed by Engineer-in-Charge

All as per item No 81 above but with conductor of size 2.5 Sq mm (nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 1.5 Sq mm PVC insulated stranded copper conductor cable complete all as specified and directed by Engineer-in-Charge

M&L for Sub main wiring with two single core, 6 Sqmm, PVC insulated PVC unsheathed stranded FR copper conductor cable in and including PVC concealed/ surface conduit of earth wire with 1 x4 Sq mm copper cable fixed along with the sub main in PVC conduit and connecting to earth dolly complete all as specified and directed by Engineer-in-Charge

M&L for Sub main wiring with two single core, 4 Sqmm, PVC insulated PVC unsheathed stranded FR copper conductor cable in and including PVC concealed/ surface conduit of earth wire with 1 x 2.5 Sq mm copper cable fixed along with the sub main in PVC conduit and connecting to earth dolly complete all as specified and directed by Engineer-in-Charge

M&L for switch piano type 5 Amps, single pole one way complete all as specified and directed by Engineer-in-Charge

S&F Modular switch 1 way 6A, 1 module complete all as specified and directed by Engineer-in-Charge

M&L for switch piano type 15 Amps, single pole one way complete all as specified and directed by Engineer-in-Charge

S&F Modular switch 1 way 16A, 1 module complete all as specified and directed by Engineer-in-Charge

S&F Bell push 6A 1 module complete all as specified and directed by Engineer-in-Charge

S&F Modular Bell push 6A 1 module complete all as specified and directed by Engineer-in-Charge

M & L for socket outlet 5 pin , 5 Amps flush type complete all as specified and directed by Engineer-in-Charge

S&F Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed by Engineer-in-Charge

M&L for socket outlet 2 in 1, 3 pin, 5 and 15 Amps Flush type complete all as specified and directed by Engineer-in-Charge

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed by Engineer-in-Charge

S & F stepped type electronic fan regulator flush type complete all as specified and directed by Engineer-in-Charge

S & F Fan step regulator, 120W - 2 module complete all as specified and directed by Engineer-in-Charge

S & F in replacement lamp holder insulated body threaded deme, with back plate,button/ angular type with sutable for battern fitting complete all as specified and directed by Engineer-in-Charge

S&F for ceiling rose surface bakelite 65x50mm two to three terminals complete all as specified and directed by Engineer-in-Charge

S&F White cover plate with frame,1 module complete all as specified and directed by Engineer-in-Charge

All as per item No 102 above but but 3 module complete all as specified and directed by Engineer-in-Charge

All as per item No 102 above but but 6 module complete all as specified and directed by Engineer-in-Charge

All as per item No 102 above but but 8 module complete all as specified and directed by Engineer-in-Charge

S&F Metal flush box/ PVC box 1/2 module complete all as specified and as directed by Engr-in-Charge.

All as per item No 106 above but but 3 module complete all as specified and directed by Engineer-in-Charge

All as per item No 106 above but but 6/8 module ccomplete all as specified and directed by Engineer-in-Charge

S&F in repair call bell ding dong type 230 volt single phase complete set inclusive suitable size wire from ceiling rose to calling bell complete all as specified and directed by Engineer-in-Charge

S&F Exhaust fan 10"/12" sweep complete all as specified and directed by Engineer-in-Charge

S&F PVC Exhaust fan 300MM sweep complete all as specified and directed by Engineer-in-Charge

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose , complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable and tubes wit suitable size complete all as specified and directed by Engineer-in-Charge

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge

S & F Recess mounted LED Light Fitting 15 Watt pressure die-cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and incl separate replaceable electronic driver compatible for Analog/DALI Dimming complete all as specified and as directed by Engr-in-Charge.

S&F in replacement Edgelit LED slim panel light fitting 2'x2' 40 watt having powder coated extruded Aluminium body with high quality LGP and PMMA diffuser swparate HPF driver suitbale for Armstrong and grid ceilling 6000 K , including connecting up with twin core twisted flexible copper cable with suitable size complete all as specified and directed by Engineer-in-Charge

S & F Electronic drivers suitable to fix Recessed mounted LED Light Fitting 15 Watt round shaped complete all as requred on site for smooth functioning of lights complete all as specified and directed by Engineer-in-Charge

S & F Electronic drivers suitable to fix Recessed mounted LED Light Fitting 2'x2' 40Watt 6000 K/5400K completemake and model all as requred on site for smooth functioning of lights complete all as specified and directed by Engineer-in-Charge

S & F MCCB 4 pole 125 Amps 16 kA complete all as specified and as directed by Engr-in-Charge.

S& F Triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB complete all as specified and directed by Engineer-in-Charge

S&F MCB DB double door Single pole & neutral 8 way with 200 amps rated bus bar complete all as specified and directed by Engineer-in-Charge

S&F MCB DB double door Single pole & neutral 12 way with 200 amps rated bus bar complete all as specified and directed by Engineer-in-Charge

Supply and fixing amp rating 240V, SP 5 To 32 AMP 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge

Supply and fixing amp rating 240V, SPN 40 To 63 AMP 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge

M&L for Taking down carefully water heater storage type 25/50 Ltrs capacity for repair and over hauling and opening to gysers and comprising of heating element , thermostate switch, electric connetions cleaning and descaling with descaling solution the geyser tank and checking of leakage on pressure at 150 PSI and testing for smooth fuctioning complete all as specified and directed by Engineer-in-Charge

S & F in Replacement of heating element suitable for geysers any type as site requirement ISI mark complete all as specified and directed by Engineer-in-Charge (a) 2.00 KW Capacity 230 Volts

All as per item ser No 125 above but 1.50 KW Capacity 230 Volts complete all as specified and directed by Engineer-in-Charge

S & F in replacement thermostat switch any type suitable for geyser of any size/model complete all as specified and directed by Engineer-in-Charge

S & F Geyser assy ( rupturing plate or U assembly) any make and type for 50 Ltrs capacity water heater incl replacement of rubber seal nuts and bolts complete all as specified and directed by Engineer-in-Charge

All as per item No 128 above but for 25Ltrs capacity complete all as specified and directed by Engineer-in-Charge

S & F in replacement of indcation lamp (pilit type ISI marked) for 50 / 25 Ltrs water heater complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement of PVC insulated flexible copper conductor cable 40/0.0076 size 3 core suitable for 650 volts grade complete all as specified and directed by Engineer-in-Charge

S & F in replacement of glass wool in any capacity of geyser complete all as specified and directed by Engr - in- charge.

S & F in replacement of water storage tank of geyser suitable for 50 Ltrs capacity complete all as specified and directed by Engr - in- charge.

All as per item ser No 133 above but for 25 Ltrs capacity complete all as specified and directed by Engineer-in-Charge

M & L for repair welding brazing of copper tank upto 25 mm to 10mm long leak proof complete all as specified and directed by Engineer-in-Charge (Capacity 25 / 50 Ltrs).

S & F in Replacement of bottom cover suitable cylindrical type geyser as per existing ad required at site for the following size complete all as specified and directed by Engineer-in-Charge (a) 50 Ltrs capacity

All as per item No 136 above but 25 Ltrs Capacity complete all as specified and directed by Engineer-in-Charge

M&L for servicing,Taking down ceiling fan 56"/48" sweep removing cleaning of dust, properly cleaning greasing of bearing including replacing and painting connecting up complete all as specified and directed by Engineer-in-Charge

Supply and fixing capacitor, capacity 2.5 mfd in replacement complete all as specified and directed by Engineer-in-Charge

Supply and fixing capacitor, capacity 3.15 mfd in replacement complete all as specified and directed by Engineer-in-Charge

M&L for rewinding of burnt ceiling fan motor 1200/1400 mm sweep with super enamelled copper winding wire of suitable guage as per details of any make /model complete all as sepecified and directed by Engr -in-Charge.

Supply and replacement of ball bearing of ceiling fan of any size complete all as specified and directed by Engineer-in-Charge

Supply and fixing and connecting flexible copper twisted twin core of size 23/00076 complete all as specified and directed by Engineer-in-Charge

M&L for servicing of wall mounting fan motor 400 mm sweep with super enamelled copper winding wire of suitable guage as per details details of any make /model complete all as specified and directed by Engineer-in-Charge

S&F wall mounting fan motor for 400 mm sweep complete all as specified and directed by Engineer-in-Charge

M&L for servicing of Exhaust fan of any size complete all as specified and directed by Engineer-in-Charge

M&L for Exhaust fan motor for 300 mm sweep complete all as specified and directed by Engineer-in-Charge

B S ENTERPRISES

36SHRI RADHEY ASSOCIATES

NAVEEN KUMAR TYAGI

MAA BHAWANI CONSTRUCTION