REPAIRS TO MES INSTALLATION, PUMP HOUSE TO CERTAIN BUILDINGS AT DAMANA UNDER GE JAMMU

Amount

B/R Portion: - Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4.0 Sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for factory made pressed steel frames of size 105 x 60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete including bottom of each chowkhat to be welded with 02 no's 25x25x3mm angle iron projecting 10cm on either side including one shop coat of red oxide chrome primer and tarring back of chowkhats and holdfasts complete all as specified and as directed.

Material and labour for factory made pressed steel frames of size 125 x 60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete including bottom of each chowkhat to be welded with 02 no's 25x25x3mm angle iron projecting 10cm on either side including one shop coat of red oxide chrome primer and tarring back of chowkhats and holdfasts complete all as specified and as directed.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with mild steel square tube supplying and fixing in opening as per specification complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and as directed.

Supply and fixing mild steel butt hinges medium weight 75 mm long complete all as specified and as directed.

Supply and fixing 35mm thick second class hard wood plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 35mm thick factory made second class hard wood, glazed and skeleton shutter open, rebated and prepared to receive glass, guage, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR 2020 Part-I section 8.24 (b) supplied and fitted to chowkhats complete all as specified and as directed.

Supply and fixing mild steel butt hinges medium weight 100 mm long complete all as specified and as directed.

Supply and fixing box type steel windows / ventilator (factory made) outer frame made out of ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler / AC window complete all as specified and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3 all as directed. Notes: - The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. (ii) 4 no's MS steel lugs made of 20X5 mm Iron flat 200 mm long. (iii)10 mm Sq Bar grill/guard bar design as per drawing. (iv) PCC block for embedding lugs

Supply and fixing aluminium handle cast type, anodised size 150mm long, 'D' type complete all as specified and as directed.

Supply and fixing aluminium anodised barrel tower bolts, with bright bolt and fixed 200mm complete all as specified and as directed.

Supply and fixing 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

Supply and fixing in repairs helical door spring 150mm including roller and roller plate complete fixed with welding to existing steel chowkhats complete all as specified and directed.

Hacking out old broken glass of any thickness, size, quality or description from the wooden / steel frames glazing with putty or fixed with wooden beads complete all as specified and as directed.

Supply and fixing 3mm thick ordinary glass sheet quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane including punching or drilling out old glazing pins or spring clips and providing and fixing new clips or pins, including scaffolding to reach upto 4 storey building complete all as specified and as directed.

Description all as per Ser item No. 18.00 here-in-before but frosted glass complete all as specified and as directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 15mm complete all as specified and as directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 20mm complete all as specified and as directed.

Supply and fixing steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm complete all as specified and as directed.

Supply and fixing steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 20mm complete all as specified and as directed.

Refixing only 15mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and as directed.

Refixing only 20mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and as directed.

Supply and fixing in repair PVC low level flushing cistern valveless, syphonic action type of 10 litres capacity white with inlet, ball valve, float and handle including cast iron brackets, PVC flush pipe 32mm dia, PVC connection (15 x 450 mm) long complete all as specified and as directed.

Supply and fixing in repair vitreous china squatting pan 'Orissa' pattern size 580 x 440mm white, with integral foot rest 'P' or 'S' trap, front or back inlet including connection to trap and to flushing pipe, anti-syphonage pipe, etc. complete making good to floor as existing complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs stainless steel sink with drainage board, made of 1.00mm thick sheet for kitchen or laboratory with plug, washers, waste pipe including bedding in cement mortar to dwarf wall or including fixing cast iron cantilever brackets, connecting union to pipe, overall size 915mm x 460mm, bowl size (410x330x160mm) as in repair complete all as specified and as directed.

Supply and fixing in repairs vitreous china wash hand basin white, flat back of size 550x400mm including waste pipe and coupling, cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs pillar tap fancy type chromium plated with capstan head, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipes 15 mm bore dia complete all as specified and as directed.

Supply and fixing in repairs PVC connection 15mm, 450mm long with nuts and washers complete all as specified and directed.

Supply and fixing in repairs chromium plated bib tap 15mm size with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

Supply and fixing angle / stop valve of cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed 15 mm bore complete all as specified and as directed.

Supply and fixing swivel shower rose PTMT any colour with arm 15mm size 195mm long complete all as specified and as directed.

Supply and fixing in repairs waste coupling of PTMT (half or full threaded) of bore dia 32 mm discharge pipe complete all as specified and as directed.

Supply and fixing in repair grating doom 100mm dia without hole chromium plated complete all as specified and as directed.

Supply and fixing in repair grating doom 100mm dia with hole, chromium plated complete all as specified and as directed.

Supply and fixing PVC waste pipe 32 mm dia and suitable length straight or flexible type for wash hand basin / sink complete all as specified and as directed.

Supply and fixing in repairs tubular towel rail, 20mm dia, 'D' type 60cm long between flanges of brass chromium plated complete all as specified and as directed.

Dismantling PVC water tank / demolition of RCC water storage tanks of capacity upto 1000 litres and removing from site complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water storage tank including plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 litres including making connections, 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gram) complete all as specified and as directed in SSR Part - I.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water and removing unserviceable material outside cantt area all as specified and directed by Engineer-in-Charge. Note: - Plaster work may be in patches upto triple storey.

Material and labour for rendering 10 mm thick in cement mortar (1:6) on fair faces of brick surface finished even and smooth without using extra cement upto height of four storey building complete all as specified and as directed.

Material and labour for rendering 5 mm thick in cement mortar (1:3) on fair faces of concrete surface of ceiling, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick surface finished even and smooth without using extra cement etc. complete all as specified and as directed (including all necessary scaffolding, lifting arrangement for external surfaces).

Material and labour for applying two coats of oil bound distemper to newly plastered surfaces including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying two coats of cement based paint over a coat of primer including preparation of new plastered surface complete all as specified and as directed.

Material and labour for applying three coats of white wash on ceiling including preparation of newly plastered surface complete all as specified and as directed.

Material and labour for applying two coats of synthetic enamel paint on wooden surface over one coat of pink primer including preparation of new surface over 10cm width or girth complete all as specified and as directed.

Material and labour for applying two coats of synthetic enamel paint on new steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surface complete all as specified and directed.

Dismantling floors, hearth or wall tiling including cement mortar bedding (but not backing) removing unserviceable materials outside MOD area and rubbish off the premises complete all as specified and as directed.

Material and labour for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles 300x450x7 to 8 mm thick on vertical surface as in skirting, dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and 10 mm thick screed in cement mortar (1:4) complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

Supply and fixing machine cut kota stone slab flooring 18-20mm thick over 20 mm thick cement screed bed in cement mortar (1:4) laid and jointed with grey cement slury mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer–in-Charge.

Supply and fixing machine cut kota stone slab 18-20mm thick over 10 mm thick as in vertical surface over rendering in cement mortar (1:3) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

Dismantling asbestos cement (corrugated or semicorrugated etc) sheets in roof covering complete all as specified and directed.

Material and labour for pre-painted galvalume aluminium zinc coating galvanised iron based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for pre-painted galvalume aluminum zinc coating galvanised iron based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section framed work of any description complete all as specified and directed.

Supply and fixing for structural steel works of Fe 410W (Grade 'E' 250) quality 'A', as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate / red oxide primer paint (including preparation of surface) before fabrication complete all as specified and directed.

Dismantling boarding in any description fixed in any position with nail complete all as specified and directed.

Supply and fixing for frame work for ceiling with specification as under mentioned: - (i) GI section frame work (Powder coated) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmX19mmX0.45mm, cross 'Tee' 28.6mm (web) X 24mm flange 0.33mm thick powdered coated main tee 38mm (Web) X 24mm flange 0.33mm thick. Wall angle shall be screwed / fixed to brick wall / partition wall / concrete / RCC with the help of nylon sleeves and screws @ 610 mm centre to centre, then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm centre to centre to soffits. To from grid of 610 X 610mm cross Tee shall be provided @ 610mm centre to centre in both directions and all suitable provisions shall be made for fixing the recessed / surface mounting light fittings if any complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing for 4mm thick of size 605 X 605 mm, white pre-premiered, self embossed, reinforced designer board for false ceiling conforming to IS-14862 and ISO-8336:1993 fixed / laid / inserted to galvanised iron framework at ceiling with screws complete all as specified and directed.

Supply and fixing in repair stainless steel curtain rod, with fixing brackets, side ball stops, rollers, etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing unserviceable material outside cantt area complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Material and labour for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed.

Description all as per Ser item No 69.00 here-in-before but except bricks complete all as specified and directed.

Material and labour for 75mm thick cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in floor/plinth protection laid in suitable panels finished even and fair. 6mm joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 grade and three parts of sand (all by weight) complete all as specified and directed.

Material and labour for 75 mm thick cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc complete all as specified and directed.

Supply and fixing chequered coloured cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in cement slurry in floors with grey pigment cement and pigments including and over 15mm thick screed bed or bedding layer of cement mortar (1:4) set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles finish complete all as specified and directed.

Material and labour for 60 mm thick machine pressed precast concrete interlocking paver block with grey / coloured cement and pigment, any shape and size confirming to IS : 15658-2006, M-35 grade complete all as specified and as directed.

Material and labour for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

Material and labour for plain cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregates) as in copings etc and in similar works including weathering, slightly rounded or chamfered angles and throating and necessary form works complete all as specified and as directed.

Supply and fixing in repair 110 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall complete all as specified and as directed.

Supply and fixing in repair 75 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall complete all as specified and as directed.

Supply and fixing in repairs PVC (SWR) bends of bore 110mm dia complete all as specified and directed.

Supply and fixing in repairs PVC (SWR) bends of bore 75 mm dia complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out in soft / loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

Material and labour for plain cement concrete type (1:3:6) C-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

Supply and fixing posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire; flat iron fillets (for securing wire mesh) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Grade E-165 complete all as specified and as directed.

Material and labour for mild steel rag or lewis bolts 12 mm dia and nuts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, not exceeding 15cm complete all as specified and as directed.

Material and labour for mild steel round bars 8 mm dia and over of Fe-410 W quality 'A' or Fe-290 quality 'A', bent to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips in chain link fencing complete all as specified and as directed.

Material and labour for mild steel in flat, round or square bars, in available length 40 x 6 mm FI strip fixed to chain link fencing complete all as specified and as directed.

Dismantling fencing wire mesh in any type complete all as specified and as directed.

Supply and fixing chain link fencing of minimum 4mm dia galvanised iron wires and 100 x 100mm mesh size including rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Material and labour for 25 mm thick plain cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in levelling course mixing liquid water proofing compound as per manufacturer's instruction complete all as specified and as directed. Note: - Liquid water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and as directed.

Material and labour for cleaning the roof surfaces and applying bitumen primer @ 0.30 kg / Sqm, providing and laying 3mm thick APP modified water proofing membrane weighing not less than 3.00 kg / Sqm reinforced with non woven polyester mat weighing not less than 160 gm / Sqm having softening point not less than 800 N / Sqcm, tearing strength of 180 N, with minimum of 10 cm side laps and 15 cm end laps, laying by application of torch and applying industrial bitumen 85/25 @ 1.2 kg / Sqm on top surface complete including removal of existing old treatement from roof surfaces such as tiling, tarfelt, fungus, moss, dust etc., cleaning the surface of all foreign material by wire brushing and dusting complete all as specified and as directed.

Material and labour for laying 40mm thick brick / PCC tiles laid over 15mm thick screed bed in cement mortar (1:4) with water proofing compound and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces by scrapping down smoke dust, mould, moss and efflorescent salt and removing oily and greasy spots etc and applying one coat of oil bound distemper including wall putty on wall complete all as specified and as directed.

Material and labour for complete removal of existing treatment of external walls including cornices, pillasters by brooming down or steel wire smoke, root, moulds, moss and efflorescent salts and trading oil and greasy spots by using suitable chemical and removing nails, making good holes with chalk whiting, filling cracks and brooming to remove all dirt etc, applying two coats of weather proof paint exterior grade over one coat of primer on walls and making good the depression etc with wall putty surface even and smooth including all scaffolding arrangement upto four storeyed building complete all as specified and directed (including all necessary scaffolding, lifting arrangement upto 12 metre height).

Material and labour for preparation of old steel surface of any description exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of old wooden surface of any description exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of old plastered or unplastered surfaces of walls including cornices, pillasters by brooming down or steel wire smoke, root, moulds, moss and efforescent salts and trading oil and greasy spot by using suitable chemical and removing nails, making good holes with chalk whiting, filling cracks and brooming to remove all dirt etc and applying one coat of cement based paint on old prepared surfaces of walls complete all as specified and directed.

E/M Portion: - Taking down old unserviceable copper / aluminium point wiring concealed / batten (light, fan, socket or power) complete including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden / iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down carefully unserviceable distribution boards of any type / size with MCB's and disconnecting and making good disturbed surfaces complete all as specified and as directed.

Material and labour for point wiring for one light / fan / call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into new concealed PVC rigid / steel conduit and into existing cast iron / pressed steel sunken / terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and as directed.

Description all as per Ser item No 101.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board ISI marked complete all as specified and directed.

Description all as per Ser item No 101.00 here-in-before but for multi 5 pin socket outlet 5 amp socket on independent board ISI marked complete all as specified and directed.

Description all as per Ser item No 101.00 here-in-before but for multi 6 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green color complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair LED light fitting 1 x 20W, 220 V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.9, 100 Lumen / Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Material and labour in repair earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 metre deep below normal ground level with top edge of the earth plate not less than 1.5 metre below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 pre-cast RCC cover slab using reinforcement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and as directed.

Supply and fixing in repair LED light fitting 10W bulk head luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing in repair fan step regulator, 100W - 1 module, 240 volts ISI marked complete all as specified and directed.

Material and labour for distribution board double door made of 2mm thick stainless steel sheet, powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Material and labour for distribution board double door made of 2mm thick stainless steel sheet, powder coated for MCB with copper bus bar and neutral link earthing stud SPN 6 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Supply and fixing in repair 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in repair SPN 40 to 63 Amp rating 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in repair for switch piano, flush type single pole one way 5 Amp, 240 volts complete all as specified and as directed.

Supply and fixing in repair socket outlet 2 in 1, 3 pin, 5 A complete all as specified and as directed.

Supply and fixing in repair switch socket outlet combined 2 in 1, 3 pin 5 amp and 15 amp flush type, 240 Volts complete all as specified and as directed.

Material and labour in repair for lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Supply and fixing in repair ceiling rose, 3 Pin / PVC / polycarbonate isolated body ISI marked complete all as specified and directed.

M/s Koul & Sons (BID ID -3069950)

bushan kumar (BID ID -3070555)

Hare krishna engineering const. (BID ID -3070444)

M/S VERMA ENTERPRISES (BID ID -3071060)

GENESIS INDIA (BID ID -3070291)