SPECIAL REPAIR TO FTL WITH ENERGY LED FITTINGS IN CERTAIN MARRIED/OTM ,PROVN OF COMMERCIAL POWER TO NFS PKG-I SITE AT AFS SALUA UNDER GE(AF) KALAIKUNDA

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil ,complete all as specified and directed.

Supplying and Laying, un-reinforced pre-cast concrete cable cover, class LV,Type II, flat, size 300 mm X 180 mm X 40 mm complete all as specified and directed.

Supply and filling in dry sand in cable trenches before and after the cables are laid, as in sand cushioning to cables complete all as specified and directed.

Returning filling in soft/loose soil, including, spreading levelling watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 Metres and depositing where directed at a level n. exc. 1.5 M above the starting point complete all asspecified and directed.

Supply, installation, testing and commissioning of CPRI approved feeder panel outdoor cubical type factory made of size 0.75x0.75x0.60 m, front and back openable type job with locking arrangement, fabricated of CRCA sheet 3.15 mm thick, Angle Iron ( 55 mm x 55 mm x 5 mm) for support, with following accessories as per manufacturer, instruction deemed to be included in quoated rates : a) MCCB, 4 pole ,250A, 415 V, 25 KA -01 No b) Phase indicator Lamps ( RYB) - set of three c) Aluminium bus bar 4 Strip. d) PCC foundation using 1:2:4 B1 cement concerte e) internal wiring for panel incl. insulators, sleeves etc.

Material and labour for LT 1100 Volts end termination cable joint kit of size 185/300 sqmm 3.5 core with complete acessories complete all as specified and directed.

Materials and Labour for plain cement concrete (1:4:8) Type D-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

Materials and Labour for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregate in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary from work complete all as specified and directed.

Materials and Labour for pre cast reinforced cement concrete (1:1.5:3) Type A1 (using 20 mm graded aggregates) in landings, covers slabs (for man holes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar (1:4), complete all as specified and directed. Note: - Reinforcement will be measured and paid separately.

M&L for 150mm dia Salt glazed stoneware drain pipes laid in trenched and jointed complete all as specified and directed.

M & L Salt-glazed stoneware gully traps, size 125x100 mm square or round mouthed, type 'P' complete all as specified

M&L concrete bed PCC (1:3:6) type C2 to drain pipes including packing under & haunching against sides of pipe after they are laid & tested for 150mm bore pipe complete all as specified and directed

Materials and Labour for plain cement concrete (1:3:6) type C2 using 40 mm graded aggregate as in surface channels and drains complete all as specified and directed.

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:4), complete all as specified and directed.

Supply and fix mild steel TMT bars 10 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 6 to 8 mm dia., cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on other than fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound will be deemed to included in quoated rates)

Material and Labour for cutting of existing GI pipe line 40/25 mm bore and insert new Tee for branch connection complete all as specified and directed

Materials and Labour for 25 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 to walls and ceiling or laid in floor, complete all as specified and as directed.

Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Materials and Labour for,cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, in stone concrete block or slab walls, complete all as specified and directed.

Material and Labour for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I complete, all as specified and directed.

Materials and Labour for, Ball valves high pressure of PTMT (Minimum weight 210 gms) with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe, 25 mm bore and fixed complete all as specified and directed.

Supply and Fix, bib tap, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed.

Supply and Fix, stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.

Supply and Fix, stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Cat No.QQT-7053 of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, complete all as specified and directed.

S & F vitreous china squatting pan, 'Orissa" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing bolt, connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge.

Flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and as directed by Engineer-in-Charge.

Materials and Labour for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

S & F wash basins, vitreous china, white, flat back, size 550 mm X 400 mm with and including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws), 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and as directed.

S & F Vitreous China wash down water closet pan (Pedestal pattern), white (including fixing bolts, flushing cistern and flush pipe with and including PVC seat cover complete all as specified and as directed. (Make : Hindware of cat No 20012 or equivalent of Paryware/Cera)

S & F 10 litres capacity, low level, syphonic type, white, plastic flushing cistern as per IS 7231: 1994 with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed.

Supply and Fix sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. Make Cat no. CAN-CHR-1171N of Jaquar or equivalent make of Kohler/Marc

Supply and Fix, in repair soap dish, fixed in wall, complete all as specified and directed.Make Catpart no.AQN-7731 of Jaquar or equivalent make of Kohler/Marc

Supply and Fix, brass chromium plated, towel rail, 20mm dia, D type, 60cm long between flanges, including taking down existing one complete all as specified and directed.Make Cat no.AKP 35711P of Jaquar or equivalent of Marc/Kohler

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified and directed.

Supply and Fix, waste coupling of PTMT (half or full threaded) (Minimum weight 45gms), for 32 mm bore discharge pipe,complete all as specified and directed.

M&L cast iron soil, waste and vent pipe any length with or without ears with cement joints laid in trenches or in floors 100mm dia ,complete all as specified and directed.

S & F Cast iron branch pieces double 100mm dia (equal or unequal) ordinary or inverted (spigot or socket type or with parallel branches) with oval access door as in repair complete all as specified and directed by Engr-in-Charge

S&F Gun-metal, globe or gate valves 25mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

S & F PVC-U, type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 110 mm dia, laid in trenches complete all as specified and directed by Engineer- in- charge .

S & F PVC-U, type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 75 mm dia, laid in trenches complete all as specified and directed by Engineer- in- charge .

S & F UPVC bends without inspection door (any angle), 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge

Supply and Fix, 50 mm bore, low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm fixed complete to walls, ceilings or in floors etc., complete all as specified and directed.

S&F grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms complete all as specified and directed.

Supply and fix PVC SWR Nahani/ Floor trap plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 75 mm, complete all as specified and directed by Engineer in charge.

S&F PVC (SWR) 'P' trap of 125/110 mm bore complete all as specified and directed.

Supply,laying, jointing and testing of , LT, XLPE insulated, galvanised steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor 1100 Volts grade of size 185 Sqmm 3.5 core including connecting/testing incl lugs, cable gland etc complete as directed.

S & F in repair LED tube light fittings(T8 TYPE) with LED tube lamp nominal power 20 Watt, LED of Make Osram; Everlight; Philips; Nicha; Cree; Samsung, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts. frequency of 50 Hz, lumen output of minimum 2100Lumen efficacy of minimum 110 lumens per watt, integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 3 KV, protection grade IP 20, CRI greater than 80%, beam angle of 1200 (120 degree) clear, THD below or less than 15%, CW available CCT of 6500K, power factor of minimum 0.95 polycarbonate housing with aluminium, life span of minimum 50000 working hours as per Make :- Century (Batten Cat No.KCCF0200 box type batten suitable for 18/20 watt retofit LED tube single side connection type). LED lamp : Make : Century Cat No. TWPP020C (retrofit LED tube lamp 20 Watt, Single end connection) OR BAJAJ (Batten Cat No. BLRB DB 118 box type batten suitable for 20 watt retofit LED tube ). LED lamp : Make : BAJAJ Cat No. BLRB 18W CWI (retrofit LED tube lamp 20 Watt with AL Heat sink),) OR equivalent of CG/Philip/Wipro complete all as specified and as directed. Note : Make of batten and LED tube lamp shall be same make.

S & F in repair LED tube light fittings with LED tube lamp nominal power 9/10 Watt, LED of Make Osram; Everlight; Philips; Nicha; Cree; Samsung, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts. frequency of 50 Hz, lumen output of minimum 900Lumen efficacy of minimum 110 lumens per watt, integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 3 KV, protection grade IP 20, CRI greater than 80%, beam angle of 120o (120 degree) clear, THD below or less than 15%, CW available CCT of 5700K, power factor of minimum 0.95 polycarbonate housing with aluminium, life span of minimum 50000 working hours complete all as specified and directed MAKE: Century/CG/BAJAJ/SYSKA LED

Supply and fix in repair LED bulb 7 watt operational voltage of 170 volts to 270 volts. frequency of 50 Hz, lumen output of minimum 700 Lumen efficacy of minimum 110 lumens per watt CRI greater than 80%, CCT of 6500K, , life span of minimum 50000 working hours complete in existing fitting / batten holder complete all as specified and directed by Engr-in-Charge. Make :- Century Cat No. LUMA007C or equivalent make Havells/CG/Bajaj

BUILDCON

STAR ENTERPRISES

Ganguly Construction