ADDL/ ALTN TO TRAINING DITCH, ADDL/ ALTN TO BLDG NO P-264 AND PROVN OF PANELLING, CABLING IN DUCT, RE-FLOORING AND LEVELLING IN TWCC AT AF STN BKT

Dismantling floor, hearth or wall tiling including cement mortar bedding/rendering complete all as specified and directed.

Dismantling paver block of any thickness laid dry in floor and removing to store and rubbish off the premises. Complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoin, arches pillars but excluding ashlar facing dressed stone work and precast concrete article complete all as specified and directed.

Demolition of cement concrete (reinforced) chajjas at ground floor not exceeding 15cm thickness below or above ground level and removing demolished material from site complete all as specified and directed.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M deep and getting out in soft/loose soil complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified.

Excavating in post holes (or similar holes) each not exceeding 0.5cum, getting out in hard/dense soil, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25cm thick, complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cms thick in hard / dense soil complete all as specified and directed.

M&L for removing excavated material not exc. 50 m and depositing in soft/hard soil, where directed. complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 (Using 40mm graded stone aggregates) in foundation, filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C-2 using 40 mm graded mechanically crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks (Except Bricks), straight or curved on plain exceeding 6 metre mean radius, built in cement mortar (1:6) , complete all as specified and directed.

M&L for 25 mm thick Damp proof course of PCC (1:2:4) type B-0, using 12.50 mm graded stone aggregate with and encluding liquid water proofing compound and necessary formwork etc. complete all as specified and directed.

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cum/ sqm complete all as specified and directed.

M&L for PCC (1:3:6) type C1 using 20 mm graded stone aggregate as in copings, bed plate, plinth courses etc. rounded or chamfered on edges including necessary form work complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar (1:4) surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of old plastered or unplastered decorated surface of walls and applying one coat of cement base paint by air less spray machine (Machanical means) of any colour complete all as specified and directed.

M& L for wall care putty 1mm thick on new or old plastered surface of walls complete all as specified and directed.

M&L for preparation of surfaces and applying two coats of oil emulsion distemper over one coat of primer on newly puttied surfaces of walls complete all as specified and directed.

M&L for Vitrified out door tiles of size 300 mm x 300 mm or 400mm x 400mm x 10-12 mm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including 20 mm thick screed bed or bedding layer of mortar Cement Mortar (1:6). complete all as specified and directed.

M&L for Providing & fixing of glass mosaic pool tiles of size 200mm x 200 mm or 300mm x 300 mm on walls of swimming pool etc or any other suitable location with approved colour of random mix with standard colour of approved size 4mm thick with approved high performance epoxy grout as per manufacturers' instrution and pointed in white or coloured epoxy grout to match the tiles and heat water proof, UV stablized complete all as specifed and directed.

M&L for providing & fixing of glass mosaic pool tiles size 200 mm x 200mm or 300 mm x 300mm in flooring of swimming pool etc or any other suitable location with approved colour of random mix with standard colour of approved size 4mm thick with approved high performance epoxy grout as per manufacturers' instrution and pointed in white or coloured epoxy grout to match the tiles and heat water proof, UV stablized complete all as specifed and directed.

M&L for rolled mild steel sections or MS pipe round/square as in posts, rafters and purlins or trusees etc . where connected to common rafters and runnuing rails fixed with angle cleats or other connecting plates, nut bolts etc. confirnimg to Fe-290 Gde E-165). complete all as specified and directed.

S&F 10-12 mm thick coloured polycarbonate sheets as in roof covering and fixing on stainless steel truss/ tubular truss with sufficient and compactable washer and bolts including bending as required. complete all as specified and directed.

M&L for two coat of synthetic enamel pinting over a coat of pink primer including preparation of steel new surface over 10 cm width as girth complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed.

Taking down cement plaster from brick walls masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and directed.

M&L for Brick work using old size bricks with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

Taking down chowkats or frames area not exceeding 1.50 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1 using 20mm graded stone aggregate complete all as specified and directed. Note: – The quoted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Taking down chowkats or frames area exceeding 1.50 Sqm and not exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC (1:2:4) type B1 using 20mm graded stone aggregate complete all as specified and as directed. Note: – The qouted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

M&L for Vitrified digital double charge light coloured tiles of 8-9 mm thick ( square or rectangular) polished, area of each tiles exc. 0.34 sqm & not exc. 0.72 sqm, in floors etc. set and jointed with Balendura adhesive or equivalent as approved GE in writing and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM (1:4) all as specified and directed.

Ditto all as per item no 32 but in skirting to walls including 10mm thick cement plaster in ement mortar (1:4) as backing coat on fair faces on stone surface complete all as specified and directed.

M&L for coloured Glazed ceramic tiles of light coloured tiles 8-9 mm thick ( square or rectangular) polished, area of each tiles exc. 0.40 sqm & not exc. 0.72 sqm,in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick cement plaster in ement mortar (1:4) as backing coat on fair faces on stone surface complete all as specified and directed.

M&L for 8 mm thick readymade wooden laminated flooring, scratch and water resistant grade AC 3, AC-4 or AC-5, with and including levelling of flooring upto 2 mm high using grinding machine or other equipment, 200 micron (0.2 mm) thick polythene sheet using for as vapor barrier and 200 micron polyethylene sheet etc complete all as specified and directed. List of make.

M&L for Jet south black granite slab work of 18 to 20mm thick (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types over and including 15mm thick screed bed in CM (1:6) set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window & other Frames/ Chowkhat of size 75mm x 50mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction.

S & F factory made WPC single extruded 100% lead free ISO certified board of 18mm thick pre laminated both side, shutter for kitchen cabinet and cupboard. The laminated shutter should be .12 microne pre laminated side with different design and other side plain white of density not less than 650 kg / cum manufactured by an ISO 9001:2015 certified company. The 18mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity and complete all as specified and directed.

S&F factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47mm x 50 mm mullion 47mm x 68mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, (Glass shall be measured and paid separately under respetive item of Sch 'A' given here-in-after).

S&F factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116mm x 45 mm & sash 46mm x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100mm x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed (Glass shall be paid separately)

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc.etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in Charge. Glass shall be measured and paid separately under respetive item of Sch 'A' given here-in-after).

S&F factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48mm x 40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19mm X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified and directed.

S&F 5.50 mm thick sheet glass, ordinary quality plain or tinted and glazing with rubber gasket in square exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F 10 mm thick sheet glass, ordinary quality plain or tinted and glazing with rubber gasket in square exceeding 0.5 Sqm in each pane, complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:6) on brick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified and directed.

Dismantling of wall and ceiling boards, any thickness including cover fillets complete all as specifed and directed.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at 900 mm (approx) centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. leat 40mm x 3 mm size and 60mm long, expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M&L for PVC insulation panels 10 mm thick with EPS stuck to 1mm printed PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. Complete all as specified and directed.

S&F magnetic ball catches with 8mm dia steel ball brass body and striking plate including letting in over all lenth of cover plate should be 140mm long complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and directed.

S&F in repairs stainless steel type curtain rod of 22 to 25mm dia including brackets & finials etc. Complete all as specified and directed.

M&L for mild steel iron steel gate with CNC Cutting Design as approved of angle or other section frame with gusset plates, rails, braces, tower bolts, sliding bolts/locking arrangements etc. complete to be prepared for hanging with and including either hooks and hinges or steel hanging door fittings including two coats synthetic enamel painting over one coat of red oxide primer etc. Complete all as specified and directed.

S&F 12 mm toughened glass in partion, sliding door & shelves etc.area not exc. 2.5 sqm each in any shape with and including stianless steel cleat for fixing to jambs/cill or flooring etc. Complete all as specified and directed.

M&L for 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC Frame complete all as specified and directed

M&L for Solid PVC Wall Lining thickness of wall lining 40 mm consisting of 5mm thick with wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed.

S&F wooden decorative type teak wood beading reqd in top portion of wall panelling fixed with nails sectional area exc. 5 Sqcm & not exc 8 sqcm including polshing complete all as specified and directed.

S&F in repair 20 mm bore tubes medium grade galvanized with all fitting such as Tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length Complete all as specified and directed.

S&F of 20 mm dia CPVC pipes SDR 11 and with all required fittings on walls/ceiling or laying in floors complete all as specifed and directed.

Supplying and laying of 15 mm dia CPVC pipes SDR 11 and with all reqd fittings on walls/ceiling or laying in floors complete all as specified and directed.

M&L for complete removal of existing treatment of walls, roof projection, fins and fascia etc. with wire brush or any manul other mechanical method by manual and reaching upto old plastered surface complete all as specified and directed.

M&L for applying 1 mm thick white wall care putty in two layers on walls complete all as specified and directed.

M &L for preparing of newly puttied surfaces of finishing walls with paint of required shade applying two or more coats of 100% Premium acrylic interior emulsion paint of having VOC less than 50 gm/litre and UV resistace as per IS 15489:2004. Alkali & Fungal resistance, dirt resistance interior paint of required shade (Company Depot tinted) with silicon additives @1.43 ltr/ 10 sqm over and including priming coat of interior primer applied @ 0.90 ltr/ 10 sqm on putty surfaces complete all as specified and directed. Note:Emulsion to be carried out through air less spray machine (Mechanical Means) (Make:- Asian Paint Apcolite Premium Emulsion/ Berger Easy Clean/Nerolac Impression Emulsion).

M &L for preparing of old painted surfaces of walls with paint of required shade applying one coat of 100% Premium acrylic exterior emulsion paint of having VOC less than 50 gm/litre and UV resistace as per IS 15489:2004. Alkali & Fungal resistance, dirt resistance exterior paint of required shade (Company Depot tinted) with silicon additives @1.43 ltr/ 10 sqm complete all as specified and directed. Note: Primer and Emulsion to be carried out through air less spray machine (Mechanical Means)(Make:- Asian Paint Apex Ultima/Berger Weather Coat Long Life 10/Nerolac Excel Everlast).

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar complete all as specified and directed.

S&F for 100 mm bore cast iron spun pipe in any length including jointing with cement joint fixed to wall complete all as specified and directed.

S&F for 75 mm bore cast iron spun pipe in any length including jointing with lead joint on wall/flooring complete all as specified.

S&F cast iron spun Bends (any radius) size 100mm bore complete all as specified and directed.

Supply & Fixed cast iron spun Bends (any radius) size 75 mm bore complete all as specified and directed.

S&F in repair 15mm bore bib tap cast copper alloy CP with crutch or butterfly handles screwed down for iron pipes or for brass ferrule complete all as specified and directed. (Make: Jaquar Opal Prime Series, CAT No. OPP-15037PM

S&F in repair 15mm bore bib tap two way cast copper alloy CP with crutch or butterfly handles screwed down for iron pipes or for brass ferrule all as specified and directed . (Make: Jaquar Opal Prime Series, CAT No. OPP-15041PM/ Jal/ Plumber as approved by GE in writting.

S&F in repair chromium plated mixer for wash hand basin for mixing hot and cold water screwed down for iron pipes suitable for 15mm bore pipe complete all as specified and dircted. (Make: Jaquar Opal Prime Series, CAT No. OPP-15441PM / Jal/ Plumber as approved by GE in writting.

S & F in repair shower panels glassy black size 1400mm x 250 mm thermostatic mixer etc. suitable 15mm bore of pipe and fixed. (Make: Jaquar, CAT No.or JPL-SSF-ST86112/ Jal/ Plumber as approved by GE in writting.

S&F in repair 15mm bore angle valves/stop valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union complete all as specified and directed. (Make: Jaquar Opal Prime Series, CAT No. OPP or-15053PM/ Jal/ Plumber as approved by GE in writting.

S&F in repair vitreous china wash hand basin table top white of size 480 mm x 480 mm with 32 mm dia chromium plated waste coupling including flush pipe etc complete all as specified and directed. (Make: Jaquar Opal Prime Series, CAT No.or OPS- WST-15901N/ Jal/ Plumber as approved by GE in writting.

S&F in repair , vitreous China Rimless Single piece with UF soft close seat cover, Hinges, fixing Accessories, Accessories Set and Cistern fittings Size: 360x675x750mm with ‘P’ or ’S’ trap complete. (Make: Jaquar Opal Prime Series, CAT No. OPS- WST-15851SN/ Jal/ Plumber as approved by GE in writting.

S & F health faucet (hand shower) (ABS body) 80mm round shape with 1.2 mtr long flexible tube and wall hook etc complete all as specified & directed.(Make: Jaquar, CAT No. ALD -573/ Jal/ Plumber as approved by GE in writting.

S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed by Engr-in-charge. (Make: Jaquar, CAT No. CAN-1111SM/ Jal/ Plumber as approved by GE in writting.

S&F in repair brass chromium plated soap tray/dish fixed with CP screws etc complete all as specified.(Make: Jaquar, CAT No. ACN-1131N / Jal/ Plumber as approved by GE in writting.

S&F in repair brass chromium plated Tumbler holder fixed with CP screws etc complete all as specified.(Make: Jaquar, CAT No. ACN-1141N / Jal/ Plumber as approved by GE in writting.

S&F in repair brass chromium plated Soap dispenser wi+E67:R84th glass bottles etc complete all as specified.(Make: Jaquar, CAT No. ACN-1135N / Jal/ Plumber as approved by GE in writting.

S&F in repair toilet paper holder of brass chromium plated fixed to walls with chromium plated (CP) brass screws etc. complete all as specified and directed. (Make: Jaquar CAT No. ACN-1151N / Jal/ Plumber as approved by GE in writting.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed (Make:Coronet/Cera/plumber / Jal/ Plumber as approved by GE in writting.

S&F Corner glass shelf with bracket and glass complete set etc. complete all as specified and directed. (Make: Jaquar, CAT No. ACN-1173 / Jal/ Plumber as approved by GE in writting.

S&F in repair brass chromium plated tubular towel rack with tower hanger (Stainless Steel) with hook complete all as specified and directed. (Make: Jaquar, CAT No. CAN-1111SM / Jal/ Plumber as approved by GE in writting.

S&F in repair brass chromium plated double coat hook complete all as specified and directed. (Make: Jaquar, CAT No. ACN-1161N / Jal/ Plumber as approved by GE in writting.

S&F Antique zinc finish metal door handles size 150 mm, polished bright complete all as specified and directed.

S&F Antique zinc finish metal barrel tower bolts of size 200mm with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of aluminium, bright finished complete all as specified and directed.

S&F in repair self closing drawer metal under mount full extension drawer sliding channel for kitchen cupboard of size 18''/20'' complete all as specified and directed. (Make: Haffle/Godrej/Hettich)

Supply & fixing self closing/auto Casement type hinges 90/180 degree. complete all as specified and directed. (Make: Haffle/ Dorma/Hettich)

S&F in repair 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore complete all as specified and directed.

M&L for providing reinforced cement concrete (1:2 :4) type B1 using 20mm graded stone aggregate as in cooking platform slab supported on wall, beam, cantilevers and kitchen cooking platform including necessary formwork complete all as specified and directed.

M&L for mild steel TMT bars, 8 mm dia , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

S&F in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified and dirceted.

S&F in repairs 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm quoted brick aggregate complete all as specified and directed.

Taking down copper/aluminium point wiring for (light, fan, socket or power) complete including unserviceable fittings such as switches, ceiling rose, holders, sockets,light fittings etc. and making good the disturbed surfaces on wall/floor etc complete all as specified and directed. Note- (i) Dismantled serviceable light fitting shoud be kept in safe custody for reuse. (ii) Refixing of serviceable fitting shall be paid seperately under relevant items-

Refixing of serviceable light fittings upto 22 watt obtained form item no 1 including connecting up with 3 core flexible cable copper conductor of suitable size from ceiling rose complete all as specified.

Taking down fans/meter/Geyser/Exhaust fan from existing position and removing the same and deposited to MES store and will installed after completion of work.

Taking down old and unserviceable sub main wiring any size/type /core incl earth wire complete with batten conduit etc all as soecified and directed.

M & L for point wiring with two single core PVC insulated & PVC unsheathed FRLS-H multistranded copper conductor cable of size 1.5 sqmm 1100 volt grade in non metallic rigid PVC concelled conduit medium grade 25 mm dia with all accessories mounting all the surface of wall/ceiling/roof/etc with suitable size of module metal flush boxes and including modular front cover plate & back plate for mounting modular type switches /socket/fan/ regulator etc including provision of one single core PVC insulated and unsheathed multi stranded copper cable of size 1.5 sqmm 1100 volt grade as earth continuty conductor connected to common earth dolly switch board complete for following- Make- Polycab/Havells/RR kables/plaza Make of PVC conduit :- AKG/ Plaza/ Jindal / Finolex One light/fan point controlled by one switch SP 5 Amps ,240 V

One bell/buzzer point controlled by bell push

One 3 pin 5 amps switch socket outlet point on independent board

One 3 pin 5 amps socket point on same board

All as per the item no 120 herein before but with 2.5 sqmm conductor for 5 pin 15 Amps switch socket outlet.

All as per item No 120 above but for one light point controlled by two 2 way switches.

S&F switch modular type 1 module single pole, one way 5 Amps. Make - Goldmedal/cabtree(havells)/L&T / Legrand.

S&F switch modular type 1 module single pole, one way 15 Amps. Make - Goldmedal/cabtree(havells)/L&T/ Legrand.

S&F s socket outlet 2 in 1, 5 pin, 15 Amps modular type 2 module Make - Goldmedal/cabtree(havells)/L&T/ Legrand.

S&F socket outlet 5 Amps modular type 2 module Make - Goldmedal/cabtree(havells)/L&T/ Legrand.

Ditto all as per item no 5 but Bell push 5 Amps Make - Goldmedal/cabtree(havells)/L&T / Legrand.

Ditto all as per item no 5 above but 5 Amps 2 way switch Make - Goldmedal/cabtree(havells)/L&T/ Legrand.

M&L ceiling rose,PVC/polycarbonate, isolated body Make - Goldmedal/cabtree(havells)/L&T / Legrand.

S&F stepped type electronic fan regulator modular type 1 module Make - Goldmedal/cabtree(havells)/L&T / Legrand.

S&F bell, ding dong type AC, 230 Volt, single pole. Make - Goldmedal/cabtree(havells)/L&T / Legrand.

S&F Sheet metal enclosure 8 way double door distribution board when MCB to be used SPN 240 volt sheet complete all as specified and directed . Make :- Havells / Legrand / Seimens/ L&T.

S&F Sheet metal enclosure 8 way double door distribution board when MCB to be used SPN 240 volt sheet complete all as specified and directed . Make :- Havells / Legrand / Seimens/ L&T.

S&F MCB SPN 32 to 40 Amps 240 volt,50 hz,10 KA breaking capacity :C" curved type complete all as specified and directed. Make :- Havells / Legrand / Seimens / L&T.

S&F MCB SPN 32to Amps 240 volt, 50 hz, 10 KA breaking capacity 'C' curved type complete all as specified and directed.

S&F socket outlet 5 pin 20 amp modular type 2 module with suitable size of module metal flux boxes and including modular front cover plate and back plate for mounting modular type switch & socket with one single pole one module MCB of 20 amp including electrical connection all as specified and directed by Engineer-in-Charge. Make :- Havells / Legrand / Seimens / L&T.

S&F batten holder backlite with 1x9 watt LED bulb includig all fixing accessories and making connection with copper conductor all a s specified and directed. Make : Havells / Philips / Bajaj / L&T.

S&F LED light fittings 1x18/20 watt ,220 volt AC decorative box type with driver holder including 18 watt LED tube light connecting up with 3 core flexible cable copper conductor of suitable size from ceiling rose complete . Make : Havells / Philips / Bajaj / L&T.

M&L for Sleek LED mirror light 10 watt rating with diffuser 2ft long twisted flexible copper wire (approx 0.5 mtr long) complete all as specified & approved by EIC. Make : Havells / Philips / Bajaj / L&T.

S&F exhaust fan made of sturdy engineering plastic complete with louvers shutter volt 230 V 50 Hz RPM 1200 copper winding of sweep 250 mm. Make : Havells / Philips / Bajaj / L&T.

Demolition of cement concrete of any description and in any position and complete removal of demolished material exc. 500 m and upto total distance of 1.5km to outside Defence land complete all as specified and as directed.

M&L Brick work with fly ash old size bricks, straight or curved to any radius in half brick thick walls, built in CM 1:4 complete all as specified and as directed. .

M&L for preparation of surface and applying two coats of oil emulsion distemper over and including 1 mm thick one coat of wall care putty, on new plastered surfaces of walls complete all as specified and directed.Note: Putty, Primer and Emulsion to be carried out through air less spray machine (Mechanical Means.

M&L for providing, cement concrete type B1 1:2:4 (12.5mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including all necessary from work complete all as specified and directed.

M&L for 100mm thick PCC (1:4:8) type D-2 ussing 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for Plates (Plain or chequered) channels in duct cover, square cut or notched (ordinary and counter sunk) forming holes for steel bar handle, without any attachment complete of Gde Fe 410-W(Gde-E-250) Quality -B complete all as specified and as directed.

M&L for arrangement of soil from out side of MoD land and forming embankement including raising (or lowering) earth, spreading in layess at site watering ramming/ rolling and finisning to required size & shaps etc not exceding 5 meter high from base as scope complete all asspecified & directed.

S&F in repair soild PVC wall lining consisting of 5mm thick prelam PVC sheet in strips & channel feathered at the edges for fixing on soild PVC Wall lining,insulated PVC wall lining and soild PVC Partitions inclusive of solvent cement complete all as specified and directed.

M&L for Disconnecting ,dismanteling and Taking out functional split AC and reassembling fixing and testing including installation of AC in new position/location after making necessary cutting/opening in wall including welding and brazing of copper pipe including charging of gas (if required) testing and making good to match with existing surface complete all as specified and directed Note;- (i) the rate for above item are deemed to include for necessary servicing cleaning & replacement of necessary unservicable screw/nut/bolt/washer etc with new one,brazing of cooper pipe,transportation to any location inside AF campus. (ii) cost of Additional copper pipe will measured and paid separately under respective items of Sch 'A' given here-in-after.

Supply only of Copper Pipe size 1/4"( with sleeves)

Supply only of Copper Pipe size 1/2"( with sleeves)

M&L for Taking down old unsericabel MS bracket and S&F MS factory made bracket with powder coated, fixed on wall with necessary grouting MS bolt washer duly painted suitable for stalling outdoor unit of 1.5/2 tr AC complete all as specified and directed

S&F in repair for submain wiring with two run of single core PVC FRLS-H insulated unsheathed multi stranded copper conductor cable of size 4 Sqmm 1100 volts grade and one run of PVC insulated unsheathed multi standed copper conductor cable of size 4 Sqmm 1100 volts grade as earth continuity conductor drawn through into and including rigid non metallic PVC concealed / surface conduit of suitable size on roof/wall/ceiling including making good the disturbed surfaces of wall etc complete all as directed. (Note : Two run of single core cable and one run of earth wire will be measured as one length and conduit and its accessories is deemed to be included in the quoted unit rate). Make- Polycab/Havells/RR kables/plaza. Make of PVC conduit :- AKG/ Plaza/ Jindal / Finolex

S&F modular type AC box with socket plug top and MCBs with two pin and one pin for earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed. Make: Havells/C&S/ Legrand/ L&T.

S&F in repair for Submain wiring with 2 single core PVC insulated FRLS-H multistrand copper conductor cable of size 10 Sq mm drawn into and including non metallic heavy duty rigid PVC conduit not less than 25 mm size ISI marked ivory colour (Pressfit or similar brand ) with all conduit fittings / accessories and 1 run single core 10 Sq mm FRLS multistrand copper conductor cable as continuous earth wire complete all as specified and directed. (Note for submain wiring: 10 run of single core cable and two run of earth wire will be measured as one length). Make- Polycab/Havells/RR kables/plaza. Make of PVC conduit :- AKG/ Plaza/ Jindal / Finolex

S&F sheet metal enclosure double door (MCCB DB) three phase and neutral with 200 Amps rated bus bar VTPN, 8 way vertical type, with provision of MCCB incommer, AC, 415 Volt complete all as specified & directed.Make :-Legrand/HPL / Seimens /L&T.

S&F MCB 4 pole 100 / 125 Amp 415 volts 50 HZ 25 KA breaking capacity complete all as directed.Make :- Legrand / HPL / Seimens / L&T

S&F in repair MCB single pole, 6 to 32 Amps, 240 Volts 50 HZ, 10 KA breaking capacity complete all as directed.Make :-Legrand / L&T / Seimens / Havells.