Addn altn to grnd floor of Bldg No P52 at MO Spl rep of common wash room behind MT Pool at MO Provn of hard standing apch rd at NIH Spl rep of washroom at bldg No 150 INS gmk Provn of split type AC for CCTV surveillance room at NIH under GE Gmk

Amount

Demolition of reinforced cement concrete(reinforcement cut as required to facilitate demolition) as in roof, floors (other than ground floors), beams, stair cases, landing, chajjas and similar suspended work complete all as specified and directed.

Excavation in trenches in soft/disintegrated rock, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out complete all as specified and as directed.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed.

M&L for precast cement concrete block masonry, type C-1 (1:3:6) (20 mm graded aggregate) with solid blocks, exc 10 cm in width and setting in CM 1:6 complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in copings and the like including weathering, slightly rounded or chamfered angles and throating with and including necessary form work complete all as specified and directed.

M&L for 75mm thick cement concrete type C2 1:3:6 (using 40 mm stone graded crushed stone aggregate) as in plinth protection surface finished even and smooth without using extra cement including forming construction (dummy) joints 6 mm wide & 10 mm deep and filled with filler at an interval not exceeding 3 metre and at change of direction and necessary formwork complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing tiles and rubbish off the premises complete all as specified and directed.

M&L for 40 mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in sub base/levelling course finished rough to receive floor/screed complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450 x 350 x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:4 finished rough to fix tiles complete all as specified and directed.

M&L for chequered cement concrete tiles 200 x 200 x 25 mm thick set jointed and pointed in neat coment slurry in floors with grey cement and pigment with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

Taking down cement or cement lime plaster on walls/ concrete/roof slab any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

Providing and applying 15 mm thick ready mix external sand faced cement plaster with neat cement rendering at all locations in two coats on masonry (except stone masonry) and concrete surfaces with and including mixing water proofing compound to the first coat of plaster as per manufacturers specification, racking out joints, hacking of concrete surface, finishing, curing, scaffolding etc complete all as specified & directed.

M&L for applying a coat of SmartCare Primero with dilution ratio of 1:1 with water maintain a coverage of 100 sq.ft/ltr cleaning off the dust, dirt etc. and filling cracks with smart crack filler mixed with cement in 1:3 on walls complete all as specified & directed.

M&L for preperation of new surface wall/ceilling by scrapping/ rubbing, applying two coat of advanced anti-algal weather proof 100% acrylic smooth emulsion with silicon additives, over a coat of fibre reinforced elastomeric liquid water proofing membrane (Asian paint damp proof + ultima suprema, exterior anti fungal paint or equivalent), including making proper surface by applying ready mix preparatory wall care putty wherever required complete all as manufacturers instructions and as directed. Note:- The application of paint shall be done by the authorized applicator of the company and also the dealer/company shall appoint a person to inspect and validate the application of emulsion in stage wise manner.

M&L for preperation of old surface wall/ceilling by scrapping/ rubbing, applying two coat of advanced anti-algal weather proof 100% acrylic smooth emulsion with silicon additives, over a coat of fibre reinforced elastomeric liquid water proofing membrane (Asian paint damp proof + ultima suprema, exterior anti fungal paint or equivalent), including making proper surface by applying ready mix preparatory wall care putty wherever required complete all as manufacturers instructions and as directed. Note:- The application of paint shall be done by the authorized applicator of the company and also the dealer/company shall appoint a person to inspect and validate the application of emulsion in stage wise manner.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-410-W (Gde-E-250) quality A complete all as specified and directed.

S&F rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe- 410W.Gde-E-250 quality 'A' complete all as specified and directed.

Providing and applying 12 mm thick ready mix external sand faced cement plaster with neat cement rendering at all locations in two coats on masonry (except stone masonry) and concrete surfaces with and including mixing water proofing compound to the first coat of plaster as per manufacturers specification, racking out joints, hacking of concrete surface, finishing, curing, scaffolding etc complete all as specified & directed.

M&L for applying one coat of alkali resistant primer on plastered surfaces of wall over 3mm thick wall care putty and applying two coat of oil bound distemper including preparation of new surfaces complete all as specified and directed.

M&L complete removal of existing treatment of wall and applying one coat of alkali resistant primer on plastered surfaces of wall over 3mm thick wall care putty and applying two coat of oil bound distemper including preparation of old surfaces complete all as specified and directed.

M&L for complete removal of existing treatment of ceiling and applying 3 mm thick wall care putty and applying two coat of oil bound distemper including preparation of new surfaces complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 Sqm each complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 Sqm and n. exc. 4.00 Sqm each complete all as specified and directed.

S&F aluminium powder coated (thickness or powder coating not less than 50 micron) frame and shutters for doors/windows/ventilators, sliding/ fixed/ openable type complete with necessary fittings including necessary arrangements to receive glass or wire mesh with aluminium channel beading & stainless steel screws complete all as specified and directed. Note : (a) The weight of rubber gasket beading will not be measured with the weight of aluminium shutters, glass/ wiremesh will be measuerd and paid separately. (b) The rate quoted by the contractor shall also include necessary wheels for sliding shutters and hinges for side hung/top hung shutter as required at sight and concealed locks for windows. (c) The colour of powder coating shall be as approved by GE.

M&L for 5.5 mm thick sheet glass ordinary quality and fixed with oil putty or rubber beading, wooden/aluminium beads and provsion of glazing pins where required in squares not exceeding 0.50 Sqm in each pane fixed in wooden/ aluminium/ steel windows/ doors/ partition/ ventilators complete all as specified and directed. Note :- Aluminium glazing strip/ metal strip paid sepetately under respective item.

S&F aluminium anodised wire mesh of size 1.5 mm x 3 mm mesh, 20 Gauge thick in doors/window shutters complete all as specified and directed.

S&F Deco-104 (10 mm thick), aluminium powder coated grill and fixed to the existing window frame with and incl 'C/F/L' channel (weight not less than 0.136 g/Rm) alround grill, CP brass/ stainless steel screw @ 200 mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles wherever required and fixing approved anodised aluminium standard section (C/F/H) around the opening all complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in hold fast etc. including necessary weathering, slightly rounded or chamfered angles and throating and necessary form work complete all as specified and directed.

M&L for 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

M&L mild steel work as hold fasts and similar small articles conforming to Fe-290, Gde E-165 complete all as specified and directed.

M&L for 30 mm thick flush shutters, solid core construction, with block board core and plywood face, pannels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

S&F Solid PVC frame (single rebated) size 60mmx30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing. NOTE: Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

S&F Factory made solid PVC moulded door shutter 28 to 30 mm thick(stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, with particle board core, supplying & fixing in frame at site complete all as directed.

M&L for preparation of new or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed all as specified and directed.

S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 125 mm long and fixed complete all as specified and directed.

S&F aluminium handles, cast type, anodised, ISI marked 150 mm size complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 25 mm dia pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm dia pipes complete all as specified and directed.

Supply, fixing, laying & testing CPVC pipes 20 mm outer dia SDR 11 including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Supply, fixing, laying & testing CPVC pipes 25 mm outer dia SDR 11 including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F in repair pillar taps, long nose, cast copper alloy, with capston heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15 mm bore iron pipe and fixed complete all as specified and directed.

Dismantling water tank capacity exc. 250 ltr but n.exc. 500 ltr complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 1000 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position fixed with and including tank nipple, union and ball valve 20 mm bore high presure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 grams) complete all as specified and directed.all as specified in SSR Part I complete all as directed

S&F in repair chromium plated brass shower roses 125mm dia with or without swival joints, including fixing to 15 mm dia pipe or union all as specified.

S&F in repair 20 mm dia brass chromium plated tubular towel rail with hooks on both ends, 60 cm long between flanges fixed with rawl plug complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest and providing lime concrete bedding and connecting to flusing cistern complete all as specified and directed.

S&F vitreous china urinal half stall type, white excluding flushing cistern, flush pipe and waste pipe but including grating and union for discharge pipe complete including providing and fixing plugs, beding urinal agianst wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back 550 x 400 mm excluding tap but including brackets 2 numbers including cutting for and pinning in ends of brackets, 32 mm CP brass waste coupling with long screwed shanks and fly-nuts, flange end bedded in red lead cement complete all as specified and directed.

S&F in repair 10 ltr PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets complete all as specified and directed

S&F in repair PVC connection 600 mm long suitable for 15 mm GI pipe with two PTMT nuts & rubber washers complete all as specified and directed.

S&F in repair long body bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S & F in repair stop valve/angle valve 15 mm nominal bore cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F 75 mm dia PVC (SWR) floor trap, with stainless steel grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1(using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in repair PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and laid in trenches or in floors complete all as specified and directed.

S&F in repair PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bend 110 mm dia, any radius fixed to pipe complete all as required and as directed.

S&F PVC (SWR) bend 75 mm dia, any radius fixed to pipe complete all as required and as directed.

S&F in repair soap dish, brass chromium plated, oval shaped of size 100 x 50mm (minimum), fixed to wall with PVC gully and CP screws complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickess including Nainital or similar pattern roofs covering complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Returning filling in including spreading watering and well raming in layer excedding 25 cm each in any type of soil/rock complete all as specified and directed.

Removing excavated material (Soils/rock) to a distance not exceeding 1.5 Km but not exc. 5 Km and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed.

Surface excavation n.exc. 30 cm deep and averaging 15 cm deep and getting out in soft/disintegrated rock complete all as specified and directed.

Removing excavated material (Soils/rock) to a distance not exceeding 50 m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed.

Hardcore of broken stone or boulder gauge exc. 63 mm and not exc. 100 mm, deposited, spread & levelled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 100 mm thick as in sub base finishing the surface even and rough to receive floor complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface/block masonary in cement mortar 1:4 finished even & smooth without using extra cement complete all as specified and directed.

M&L for applying two coats of cement base paint over a coat of alkali resistant primer on new surfaces of walls including preparation of surface complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and laid in trenches or in floors complete all as specified and directed.

M&L for fixing 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for Earth filling under floors or pavings in including spreading watering and well raming in layer excedding 25 cm each complete all as specified and directed.

S&F powder coated (any colour and thickness of coating not less than 50 micron) aluminium door frame and shutters single/double leaf glazed/ pre-laminated particle board 12 mm thick exterior grade or partly glazed and partly per-laminated board in shutters including aluminium powder coated beading, rubber packing and fixed with suitable size of thrust bolts in wall by drilling and comprising of following:- (a) Door frame made of section 101.6 x 44.45 x 1.90 mm (Cat No. 20146) (b) Vertical section of shutter size – 85 x 44.45 x 2 mm (Cat 19560) (c) Top rail, style shutter 95.25 x 44.45 x 2 mm (Cat 19505) (d) Bottom rail/ middle rail 150 x 44.20 x 2.2 mm (Cat 19517) (g) Aluminium powder coated handle 205 mm long (Cat 29426) 2 Nos. in each shutter (h) Tinted/Plain glass 5 mm thick (j) Pre-laminated particle board 12 mm thick exterior grade (k) Six lever brass mortice lock (l) Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty. (m) Aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg. NOTE :- (i) Cat No. mentioned above are of Jindal Make. Contractor can provide any other make as mentioned in List of makes attached with tender documents. (ii) In case of non avalibility of any section next higher size section matching with other sections will be used.

M&L for 4 mm thick sheet glass ordinary quality and fixed with oil putty or rubber beading, wooden/aluminium beads and provsion of glazing pins where required in squares not exceeding 0.50 Sqm in each pane fixed in wooden/ aluminium/ steel windows/ doors/ partition/ ventilators complete all as specified and directed. Note :- Aluminium glazing strip/ metal strip paid sepetately under respective item.

M&L for figured glass(frosted), 3 mm thick, pin head type and fixed rubber beading, aluminium strips in squares not exceeding 0.50 Sqm in each pane fixed in aluminium windows/ doors/ partition/ ventilators complete all as specified and directed. Note :- Aluminium glazing strip/ metal strip paid sepetately under respective item.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: frame guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works confirming to Fe- 290. Gde-E-165 complete all as specified and directed .

S&F in repair curtain rod fancy type, made out of 25mm dia MS conduit pipe duly PVC sleeved, fancy type plastic finial, decorative type, fixed to ends of rod and mild steel prepainted/PVC coated brackets suitable to hold the drapery rod and fixed to wall with the help of 2 Nos 50 mm long steel screws and rawl plug, colour and pattern as approved by GE complete all as specified and directed.

M&L for providing factory made 25 mm thick 100% solid WPC (wood polymer composite) coloured laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 (suspension grade), calcium carbonate and natural fibers (wood powders/ rice husk/ wheat husk (non toxic additives, made from extrusion process WPC foam single extruded (inner) with having minimum density not less than 650 Kg/cbm, having good screw holding capacity (Screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance of spread of flame of class A category with Property of being Termite / borer free water / moisture proof and fire Retardant WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing with necessary full body threaded star headed counter sunk SS screw complete all as directed. Note :- Material test Certificate and authentication should be compulsory provided by the manufacturing company.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long (ISI marked) and fixed complete all as specified and directed.

M&L for forming jambs etc to opening, including cutting, toothing proper bonding into old work, also facing, jointing and pointing to match the existing work, new work built in CM 1:6 complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodized with rubber washer at bottom fixed with screw to body and fixed to door shutter, over all length of cover plate shall be 150 mm complete all as specified and directed.

M&L for high glossy finish vitrified ceramic tiles of size 300 x 600 x 8-10 mm thick, to match floor tiles fixed on vertical surfaces such as dado, skirting etc. jointed and pointed in epoxy grout mixed with pigment to match the shade of tiles laid over and including 4 to 8 mm thick ready mix tiles adhesive complete all as specified and directed.

M&L for mat finished double charged vitrified ceramic tiles 9-10 mm thick (square/rectangular) polished, area of each tiles exc. 0.42 Sqm but not exc. 1 Sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including rendering 15 mm thick in cement mortar 1:6 finished rough to fix tiles complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

Demolition of stone slabs and tiles of any description and thickness as in floor, apron etc. laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for granite stone 20 mm thick (of any type) glazed (table rubbed and polished) fixed as in steps, jambs, pillars, window cills, cooking plateform and the like set in cement mortar 1:4 and pointed with white cement (1:2) using marble dust with admixture of pigment to match laid over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for machine cut cudappah stone slab 20 to 25 mm thick fixed in position laid, jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab, grinding and polishing with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking plateform and other similar situations complete all as speciifed and directed.

S&F in repairs stainless steel sink made out of 1mm thick sheet with plugs, washers, CP waste coupling and waste pipe incl bedding in cement mortar on to drawf wall or brackets fixed to wall and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair 1 mm thick stainless steel plate rack over all size 0.90 x 0.90 x 0.25 m of standard pattern and make as approved by GE complete all as directed. Make: Diamond/Nirali/Bluestar/Jayna/Neelkanth

Demolition of Brick Work/ stone work / concrete block wall built in Cement Mortar including all quoins, arches, pillars, etc. of any descriptions, complete all as specified and as directed.

M&L for precast cement concrete block masonry, type C-1 (1:3:6) (20 mm graded aggregate) with solid blocks, exc 10 cm in width and setting in CM 1:4 complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for preperation surface of wall/ceilling by scrapping/ rubbing, applying two coat of texture paint over a coat of damp proof anti fungal paint complete all as specified and directed. Note:- The application of paint shall be done by the authorized applicator of the company and also the dealer/company shall appoint a person to inspect and validate the application of emulsion in stage wise manner.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets complete all as specified and directed.

M&L for suspended false ceiling with E board classic ceiling board 4 mm thick including and fixing of frame work made of special GI section with zinc coating as per IS 277 and consisting of angle cleats of size 25 mm wide 1.6 mm thick with flag fixing to the ceiling with dash fastner 12.50 mm x 40 mm long 6 mm dia bar fixed with nut and bolts in GI channel 45 x 14 x 0.90 mm runner for fixing E board of size 600 x 600 mm including fixing of E board with ceiling section and paremeter of channel 0.50 mm thick, 27 mm high having flange of 20 mm to 30 mm long etc. and frame work to be hold with GI wire 4 mm dia to existing roof slab, truss, purlin etc. complete all as specified and directed.

S&F in repair Glass shelf with CP railing (22" x 6") complete all as directed Make:- Nixo-Cat part no- ES01A/Hilife/Cera/Prayag

S&F in repair, Glass corner shelf with CP railing(12" x 12") complete all as directed Make-Nixo-Cat no-ES03A/Hilife/Cera/Prayag

M&L for RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) as in slab, beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5 mm dia and over in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L for applying 3 mm thick wall care putty and applying two coat of oil bound distemper including preparation of surfaces complete all as specified and directed.

Dismantling water tank capacity exc. 500 ltr but n.exc. 1000 ltr complete all as specified and directed.

S&F 20 mm dia gun metal globe or gate valve with iron wheel head screwed both ends and for iron pipe & fixed complete all as specified and directed.

S&F angle/stop valve 15 mm nominal bore cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed. Make - Jaquar Cat part No. FLR 5053N or equivalent in Hindware/ Plumber/Cera

S&F CP wall mixer, for mixing hot and cold water fancy type cast copper alloy, with capstan heads, chromium plated, screwed down for 15 mm bore pipe, high pressure with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed. Make - Jaquar Cat part No. FLR 5217N or equivalent in Hindware/ Plumber/ Cera

S&F 15 mm nominal bore Bib taps, long body fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make - Jaquar Cat part No. FLR 5047N or equivalent in Hindware/ Plumber/ Cera

S&F PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts & rubber washers complete all as specified and directed.

S&F Viterous China wash down water closet pan pedestal pattern design pattern for kids any shape & size suitable for all kids above 10 years age having multicolour shade decorative flushing cistern and flush pipe) and including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Supply and fixing designer single piece WC with soft close seat cover, hinges, dual flush cistern fittings and fixing accessories size 370 x 690 x 680 mm complete all as specified and directed. Make : Jaquar Cat part No CNS-WHT-851S300SPP or equivalent in Hindware/ Cera/Jonson.

Supply and fixing counter top wash basin of size 460 x 460 x 170 mm with 32 mm dia stainless steel waste coupling, bottle trap 32 mm, fixed over granite slab counter including making hole in slab complete all as specified and directed. Make : Jaquar Cat part No JDS-WHT-25935 of Jaquar or equivalent in Hindware/ Cera/Jonson

S&F central hole basin mixer, fancy type, cast copper alloy chromium plated, with round spout with popup waste system, including plugging and fixed, suitable for 15mm bore pipe complete all as specified and directed. Make : Jaquar Cat part No. FLR 5005NB or equivalent in Hindware/ Plumber/ Cera

S&F Toilet Roll holder with stainless steel flap and paper roll complete all as specified and directed. Make : Jaquar Cat part No ACN-1153S or equivalent in hindware/ Plumber/ Cera

S&F PVC mirror cabinet of size 600 x 450 mm with hinged door covered with mirror, with brush holder, pouch holder, shelves etc. complete all as directed. Make PRAYAG/ Commander/Polytuff

S&F two-in-one Bib Taps 15 mm Bore, Cast Copper Alloy with crutch or butterfly handle screwed down, screwed for Iron Pipe or for Brass Ferrule complete all as specified and as directed. Make - Jaquar Cat part No. FLR 5041N or equivalent in Hindware/ Plumber/ Cera

S&F 10 ltr PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets complete all as specified and directed

S&F 20 mm outer dia stainless steel towel rail, 60 cm long between flanges fixed with rawl plug complete all as specified and directed. Make - Jaquar Cat part No. CAN 1111SM or equivalent in Hindware/ Plumber/ Cera

S&F soap dish, vitreous china coloured, approximate size 160 x 160 x 90 mm fixed to rawl plugs with chromium plated brass screws & washers complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bend with access door 110 mm dia, any radius fixed to pipe complete all as required and as directed.

S&F PVC (SWR) bend with access door 75 mm dia, any radius fixed to pipe complete all as required and as directed.

S&F in repair vitreous china bowl urinal flat back excluding flushing cistern, flush pipe and waste pipe but including grating and union for discharge pipe complete all as specified and directed. Make : Jaquar Cat part No URS-WHT-13261 or equivalent in Hindware/ Cera/Jonson.

Removing building materials by truck or tractor with using of if necessary JCB machine and trolly load min 5.00 Cum each load for upto 10.00 km including loading, unloading and stacking at the destination and depositing out side defence land complete all as specified and directed.

Supply and fixing of hand shower (health faucet) with 8 mm dia, 1 m long flexible tube and wall hook complete all as specified and directed. Make : Jaquar, cat part No ALD-573 or equivalent in Hindware/ Plumber/ Cera

Demolition of cement concrete unreinforced in ground floors and pavings n.exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for providing damp proof course 40 mm thick in cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) to horizontal or vertical surfaces mixed with water proofing compound as per manufacturere instructions including necessary formwork complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid seperately.

M&L for pre construction anti termite treatment by treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for pre construction anti termite treatment by treating the soil along external perimeter of the building at the rate of 2.25 litres of emulsion per meter of the perimeter wall complete all as specified and directed.

Providing and applying 10 mm thick ready mix external sand faced cement plaster with neat cement rendering at all locations on masonry (except stone masonry) and concrete surfaces as per manufacturers specification, racking out joints, hacking of concrete surface, finishing, curing, scaffolding etc complete all as specified & directed.

Hardcore of broken stone or boulder gauge n. exc. 63 mm deposited, spread & levelled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, leveled and rammed including watering complete all as specified and directed.

M&L for rendering 10 mm thick on wall in cement mortar 1:4 finished fair and even as in backing coat below tiles complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 75 mm thick as in sub base finishing the surface even and rough to receive floor complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying floor finish complete all as specified and directed.

M&L for machine cut kota stone of size not less than 550 x 550 mm (except where lesser size required) as in flooring or in trades of steps (in single piece), skirting, dado etc., 18 to 20 mm thick, bedded and jointed with grey cement slurry and pointed in white cement with admixture of pigment to match the shade of the stone including grinding, rubbing and mirror polishing complete all as specified and directed.

S&F rolled mild steel in plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W Gde- E-250 quality A complete all as specified and directed.

S&F collapsable steel gate, top hung consisting for channel pickets, pivoted flats bars, top and bottom runners and wheel, handle etc as specification, erected in position and securing runners with holdfast and brackets complete all as specified in clause No. 10.24 of SSR part-I and consisting of following:- MS channel - Hot rolled medium channel 18 x 9 x 3 mm Tee and flats for top and bottom runners with a minimum web of 40 x 12 mm and flange of 40 x 6 mm Distance between centre to centre of channel pickets - 10 cm

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

M&L for point wiring complete for one light/ fan/ exhaust fan point controlled by one, one way 5/6 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including minimum 20 mm dia 'medium grade' PVC conduit ISI marked concealed in wall and fittings and modular metal flush box, modular white cover plate with frame, blanking plate and making good to the disturbed surfaces to match the existing complete all as specified and directed including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including making good disturbed surface to match the existing surface complete all as specified and directed. Note- (i) Rates include the cost of blanking plate, modular plate, modular boxes and covers of suitable modules as required at site. (ii) Modular box, plate and cover shall be of same make as of switch//socket/regulator.

All as per item No. 148 above but for one 5 pin 5/6 Amp socket outlet point on an independent board.

All as per item No. 148 above but for one 5 pin 5/6 Amp socket outlet point on same board

All as per Item No 148 above but for one 6 pin 15/16 amps socket outlet point on an independent board with FRLS cables of size 4 Sqmm and green colour earth cable of size 4 Sqmm.

S&F modular type switch one way 6 Amps, 230 Volt, 1 Module complete all as specified and directed.

S&F modular type switch one way 16 Amps, 230 Volt, 1 Module complete all as specified and directed.

S&F modular type socket one way 6 Amps, 2/3 pin, 230 Volt, 2 Module complete all as specified and directed.

S&F modular type socket one way 6/16 Amps, 2/3 pin, 230 Volt, 2 Module complete all as specified and directed.

S&F ceiling rose, two or three terminal, surface bakelite 65 x 50 mm complete all as specified and directed.

S&F modular type fan regulator, electronic step type, 120 W, 2 Module complete all as specified and directed.

S&F in replacement exhaust fan (Metal body) of 300 mm sweep, AC single phase 230/240 volts, 1400 RPM, heavy duty complete including making electric connection with PVC insulated three core 1.5 Sqmm copper cable from ceiling rose to exhaust fan, making hole in wall of suitable size, grouting anchor bolts/fastners and making good to disturbed surfaces to match the existing complete all as specified and directed. NOTE:- Old exhaust fan will be deposited to MES store yard. Make : Orient Ind heavy duty 1400RPM/ Havells Turbo force 1P(FHEHDSPDB120) /Bajaj Supreme plus Ind fan

S&F in repair brushless direct current (BLDC) ceiling fan 1400 mm sweep with service value 6.00 BEE, 5 star rating complete with blades and other accessories, single phase, 230 V including 1 m long down rod and making connection with sheathed 3 core cable of size 0.75 Sqmm flexible copper conductor wire complete all as specified and directed. NOTE:- Old exhaust fan will be deposited to MES store yard. Make : Havells cat No- FHCNF5SWHT56/Orient model Hector 500/ Bajaj Model- ENERGOS 28(SKU Code 251100EE)

S&F in replacement existing U/S light fitting with LED tube light fitting surface and wall mounted batten Aluminium body with 22/20 watts LED having minimum 100 lumens/watts and with integrated electronic driver complete all as specified and directed. Make: Philips cat No-BN021CLED22S PSU CW GR/ Crompton cat no-CCS-103-20-65-SL-DP-NWH/ Halonix HLB-03-20-CW-AL-SQ.

S&F in replacement existing U/S light fitting with Recess mounting LED fittings 36 watts, 600 mm x 600 mm (2ft x 2ft), 6500 K, suitable for modular/ POP/ Gypsum ceiling, luminaire with white powder coated CRCA housing with LEDs. seamless front frame with fat white high transmission acrylic cover 230V, complete in all respect & accessories internally prewired including connecting up with twin core copper twisted flexible copper conductor cable complete all as specified and directed. Make: Havells cat No-VENUSNEO2X2PLR36WLED865G2/ Philips cat No-RC380B LED36S-6500 G5 L60W60 PSU OD SG / Halonix HLFPR22-11-36-CW-37mm-WC.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4 Sqmm nominal cross sectional area and one run of 4 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 32 mm PVC conduit and fittings concealed in wall/ roof/ floors/ ceiling etc. including cutting chases to walls for laying conduit wherever required and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire, one run of earth wire and one run of PVC conduit

S&F in replacement MCB single pole 240 volts, 'C' curve of rating from 16 to 32 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement MCB SPN 240 volts, 'C' curve of rating 40-63 Amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection single pole and neutral 240 volts, 4 way, including suitable size copper bus bar and metal door, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

M&L taking out old earthing and providing new earthing complete with galvanised steel plate electrode 600 mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron strip 25 x 4 mm by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5 mm graded stone aggregate reinforced with 6 mm dia round bar @ 75 mm C/C both ways with MS handle 8 mm dia, plastering 15 mm thick CM (1:6) externally upto 150mm below ground level, GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl. excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test point incl testing complete all as specified an directed. Note:- The unit rate includes the cost of GI pipe medium grade for protection of earth wire and earth strip upto 7.5 M.

M&L for point wiring complete for one light/fan/ exhaust fan point controlled by one flame proof switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including stove enamelled steel conduit minimum 20 mm ISI marked fixed on wall and flame proof ceiling rose complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including making good disturbed surface to match the existing surface complete all as specified and directed.

Supply and fixing flame proof rotary type switch with termination box in LM6, Single pole 250 Volts, ON or OFF Element including flexible metal pipe with threaded ends to connect between rotary switches complete all as specified and directed.

S&F FLAMEPROOF exhaust fan (Metal body) of 300 mm sweep, AC single phase 230/240 volts, 1400 RPM, heavy duty complete including making electric connection with PVC insulated three core 1.5 Sqmm copper cable from ceiling rose to exhaust fan, making hole in wall of suitable size, grouting anchor bolts/fastners and making good to disturbed surfaces to match the existing complete all as specified and directed.

S&F FIAMMA II flameproof 2x20W LED tubelight fixture with IP 65 protection etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make :- Cat Part No EXTN1LT8-16/20 of CG or equivalent make : Sudhir/Balinga

S&F flameproof 100 watt LED flood light fixture with IP 65 protection etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4 Sqmm nominal cross sectional area and one run of 4 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 32 mm dia stove enamelled steel conduit fixed on wall/ roof/ floors/ ceiling etc. including cutting chases to walls for laying conduit wherever required and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire, one run of earth wire and one run of PVC conduit

S&F sheet metal enclosure MCB distribution board, double door with IP-43 protection single pole and neutral 240 volts, 8 way, including suitable size copper bus bar and metal door, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

M&L for earthing complete with galvanised steel plate electrode 600 mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron strip 25 x 4 mm by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40 mm thick (1:2:4) type B-0 using 12.5 mm graded stone aggregate reinforced with 6 mm dia round bar @ 75 mm C/C both ways with MS handle 8 mm dia, plastering 15 mm thick CM (1:6) externally upto 150 mm below ground level, GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl. excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test point incl testing complete all as specified an directed. Note:- The unit rate includes the cost of GI pipe medium grade for protection of earth wire and earth strip upto 7.5 M.

S&F, testing and commissioning of microprocessor based networkable analogue addressable Fire alarm control panel complying with BS EN 54 2 loop panel of capacity from 99 detectors and 99 modules and upto 200 detectors. The panel must have LCD with resistive touch screen and automatic backlight dimming and having 240 V AC power supply along with battery 12 V, 7.5 Ah-02 Nos and suitable automatic battery charger complete all as specified and directed. Make:- Edward/Honeywell/Apollo/Notifier

S&F Fire detector complying with and type certified to EN-45 addressable type smoke and heat (Multisensor) detector Photoelectric/ Optical with base with self built intelligence as per IS:11360 complete all as specified and directed. Make:- Edward/Honeywell/Apollo/Notifier

S&F addressable type Manual Call Point break glass type with integral short circuit Isolator alarm LED complete all as specified and directed. Make:- Edward/Honeywell/Apollo/Notifier

S&F remote response indicators complete all as specified and directed.

S&F addressable control module with integral short circuit isolator complete all as specified and directed. Make:- Edward/Honeywell/Apollo/Notifier

S&F fire alarm Sirens electronic type horizontal single stage continous normal operation for at least 50 minutes with sound level 65 DB to 120 DB measured at 1.5 meter with sound output variation of +5 DB for 500 meter range complete all as specified and directed. Make:- Edward/Honeywell/Apollo/Notifier

S&F 2.5 Sqmm 2 core Annealed tin-copper (ATC) conductor, PVC sheathed unarmoured, FRLS cable with required termination glands, lugs etc. complete all as specified and directed.

S&F water proof junction box with connectors complete all as specified and directed.

S&F stove enameled conduit of dia 20 mm, medium grade inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. but exclusive of boxes (junction/ terminal) fixed under wall/roof with necessary clamps complete all as specified and directed.

S&L XLPE LT UG cable PVC insulated, bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor of 16 Sqmm 4 core including gland, lugs etc. laid in trenches or fixed on wall/floor/poles complete all as specified and directed.

Supply and installing, testing, commissioning split AC unit indoor/outdoor, with cordless remote control unit and inbuilt air iodiser and plasma filter for better indoor air quality, minimum 3 star rating and ISEER rating of 3.80, 1.5 TR capacity with copper tubing condenser, low noise with 230 Volt range, LED display, anti-dust, antimicrobial protection, anti-corrosive coating, self diagnosis with all necessary fixing arrangements such as brackets etc. complete all as specified and directed. Make : Voltas Modal 18 H Vectra Platina/ Blue star Model IC318 MNU or equivalent in OGeneral/Carrier Note:- Extra copper tubing, water pipe, voltage Stabilizer etc. required to complete the installation will be measured and paid separately under respective items herein after.

S&F Voltage stabilizer 5 KVA capacity, single phase, naturally Air Cooled indoor type and designed for input variation between 170 V to 290 V with output voltage stabilized at 230 V with accuracy of + 2.5 % complete all as specified and directed. Make: V-Guard/MicroTek/Luminous

S&F flexible wire three core, PVC insulated 4 Sqmm multi stranded copper conductor, 1100 V grade complete all as specified and directed.

S&F insulation for copper tubes of split type AC units, insulation type superlon of size 3/8" diameter all as directed.

S&F insulation for copper tubes of split type AC units, insulation type superlon of size 5/8" diameter all as directed.

S&F copper tubing soft grade suitable for split type AC suction /discharge line of size 5/8" diameter all as directed.

S&F copper tubing soft grade suitable for split type AC suction /discharge line of size 3/8" diameter all as directed.

S&F PVC flexible transperant pipe 20 mm dia fixed to wall or on roof complete all as specified and directed.

S&F sheet metal enclosures, single pole and neutral with a two pin and earth plug and socket, plug top and one single pole MCB 20 Amps, C series 240 V complete all as specified and directed.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4 Sqmm nominal cross sectional area and one run of 4 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 32 mm PVC conduit and fittings concealed in wall/ roof/ floors/ ceiling etc. including cutting chases to walls for laying conduit wherever required and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire, one run of earth wire and one run of PVC conduit

S&F MCB single pole 240 volts, 'C' curve of rating from 16 to 32 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F MCB SPN 240 volts, 'C' curve of rating 40-63 Amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M/S jvsr constructions (BID ID -3514229)

M/s VEEJEE ENTERPRISES (BID ID -3513067)

Super Construction (BID ID -3513429)

M/s. R.S. LAWANDE (BID ID -3513297)

M/S P S BABU (BID ID -3514291)

M/S G.N.POWAR (BID ID -3513488)