WBPWD/EE/AED /eNIQ-72/2024-25

Amount

Supplying only the following 1.1 KVgrade PVC insulated A/Al. Cable as below:[Finolex/Havells/RR/PolyCab/EIC Approved]: i)4 core 25 sq mm.

Laying of the following PVC A/Al cable on wall/surface including S & F MS saddles with GI (HOT DIP) Wire earthing attachment, making holes etc. as necessary mending good damages and painting as below: i)upto 3.5/4 core 25 sqmm with 2X10SWG GI (Hot Dip) Wire.

Laying of cable as below, after cutting floor/pavement/wall/ and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl. removing the rubbish. i) From 2.5 sqmm to 35 sqmm at an average depth of 75 mm in floor/pavement/wall etc. .

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed.

Laying only Cable upto 50 sqmm through existing RCC/Hume/ GI Pipe/open masonary trench for single, 2, 3, 3½ & 4 core cable.

Supplying & fixing medium gauge GI Pipe (TATA-Medium) Protection with necessary fittings and jointing materials as required. i)50 mm dia

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below : i)For 4 core 25 sq mm.

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials. i)For 4 core 25 sq mm.

Finishing of the PVC insulated wire ends by socketting with pin/ring type copper sockets and insulated tapes etc., includingsupplying sockets, tapes................. i)1.5 sq mm. [For Computer board & Power Point]

ii)2.5 sq mm.

iii)4.0 sq mm.

iv)6.0 sq mm.

Supplying and fixing double door Horizontal-TPN-MCB DB housing for Four pole Isolator as incomer and DP-MCBs /SP-MCBs ('C'-curve,10kA,16-32A) as outgoing with IP-43 protection, concealed in wall after cutting the wall & mending good the damages to original finish & necy. wall matching putty & paint as required or total establishment on angle iron frame(25mmX6mm)on wall incl. inter connection with suitable size of copper wire and neutral link & provision for earthing attachment as required inside the box. #[Make : Legrand Ekinox/ABB/Eqv Make]# i)6 Way Enclosure... [For Canteen]

Supplying and fixing double door SPN-MCB DB housing for DP-MCBs as incomer and SP-MCBs ('C'-curve,10kA,6A to16A) as outgoing with IP-43 protection, concealed in wall after cutting the wall & mending good the damages to original finish & necy. wall matching paint as required or total establishment on angle iron frame on wall incl. inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. [D9:13] #[Make : Legrand Ekinox/ABB/Eqv Make]# i)2+8 way Enclosure...

ii)2+12 way Enclosure...

Supplying and fixing 240/415V, following rating MCCBs & MCBs (Legrand Make) of Breaking capacity 10kA for MCBs & 35kA for MCCBs & "C"characteristics on existing din rail for newly installed DBs and necessary connection as required. #[Make: Legrand/ABB/Eqv. Make]# i)32A DP MCB Isolator

ii)40A DP MCB Isolator

iii)63A FP MCB Isolator

v)6-32A(10kA) SPMCBs.

Supplying and fixing polythene pipe complete with fittings as necy. under ceiling/beam, bound with 22 SWG GI binding wire incl. supplying and drawing 1x18 SWG GI Wire as fish wire inside the pipes and fittings and providing 50 mm dia disc of MS sheet (20 SWG) having colour paint at one face fastened at the load point end of the polythene pipe with fish wire (synchronizing with roof/beam casting work of building construction).........(PWD Approved meterials) [Item for Power Point,Computer Board,TPNDB to SPNDB etc. connection Except light/fan/callbell point wiring] i)[19mm dia. 3mm thick Polythene Pipe]

ii)25mm dia. 3mm thick Polythene Pipe]

Cutting Channel of size (43 mm x 43 mm) & (40mm x 40mm) on masonry wall by Electric operated cutting machine incl. supplying & fixing heavy gauge 25 mm & 19mm, 3 mm thick Polythene pipe by means of anchoring chemical (Hilti/Sika) and GI 'U' hooks of 8 SWG incl. supplying and drawing 18 SWG GI wire as Fish wire and mending good damages to original finish by using own tools and tackles........ [Item for Power Point,Computer Board,TPNDB to SPNDB etc. connection Except light/fan/callbell point wiring]. i)19 mm dia and 3 mm thick polythene pipe without earth continuity wire]

ii)25 mm dia and 3 mm thick polythene pipe without earth continuity wire]

Supply & Fixing sheet metal inspection box (16 SWG) of the following sizes flushed in wall by housing the same after cutting brick wall incl. making earthing attachment,painting and mending good damages to building works........... i) 175 mm x 100 mm x 65 mm]

ii) 200 mm x 150 mm x 65 mm]

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Finolex/Havells/RR/Poly-Cab) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required........... i)3 x 22/0.3 (1.5 sqmm) [From TPN DB/SPN DB to 2X 6A]

i)2x36/0.3 (2.5 sqmm) + 1x22/0.3 (1.5 sqmm) as ECC. [E9:1s] [From TPN DB/SPN DB to 1X 16A, 2X16A, Outer Light]

ii).2x56/0.3 (4 sqmm) + 1x36/0.3 (2.5 sqmm) as ECC [E9:1v] [From TPN DB to AC 1X 25A Socket Via OLP]

ii).2 x 84/0.3 (6 sqmm) + 1 x 56/0.3 (4 sqmm) as ECC. [E9:1y] [From TPN DB to SPN DB]

Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board with top cover plate flushed in wall incl. mending good damages to original finish 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC. i) Average run 8 mtr]

ii)[Average run 10 mtr]

Distn. wiring in 2 X 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 6A 5 pin plug point incl. S&F 240 V 6A 3 pin Modular type plug socket & Modular type switch (Brand approved by EIC) incl. S&F earth continuity wire, fixed on 4 Module GI switch board with 3/4 Module top cover plate flushed in wall incl. mending good damages to original finish *[On Board]

Distribution wiring in 2 x 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit 'FR' (Precision make), with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board with top cover plate and 2 no. suitable size “Ph & N” copper bar & earthing attachment fixed on wall incl. mending good damages to original finish. i)[Average run 10 mtr]

ii)[Average run 12 mtr]

Distribution wiring in 1.1 KV single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 25mm size PVC rigid conduit 'FR' (Precision make) incl. necy. fittings as required. 2 x 36/0.3(2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm)ECC.

2 x 84/0.3 (6 sqmm) + 1 x 56/0.3 (4 sqmm) ECC.

4 x 84/0.3 (6 sqmm) + 2 x 56/0.3 (4 sqmm) ECC.

Supplying and fixing PVC Rigid Conduit 'FR' [Precision Make] on wall, ceiling with saddles and other accessories as required and mending good damages to building works. i)20mm dia. [For Canteen Area]

Supply & Fixing angular batten holder (Anchor) on 75mm dia PVC round block / round bakelite on wall/ceiling.

Supplying & Fixing GI Modular Switch Board of the following sizes complete with top cover plate flushed in wall for housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works. [For AC Socket] i)2 Module.

Supplying & Fixing GI Modular Switch Board of the following sizes complete with three no. suitable size Copper bar with holes (for Ph, N & E) fixed on bakelite/Hard Rubber insulator over the MS welded chairs incl. top cover flushed in wall for housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works. i)4 Module. [For OLP Starter]

ii)6 Module. [For 2nos 6A or 16A Socket & Switch]

Supply & Fixing of 3pin Modular type plug socket(brand approved by EIC) on existing GI modular switch box and making necy. Connections with PVC Cu wire and earth continuity wire. i)5A 3Pin Socket.

ii)15A 3Pin Socket.

iii) 25A 3Pin Socket.

Supply & Fixing of 6A Modular type switch (brand approved by EIC) on existing GI modular switch box and making necy. Connections with PVC Cu wire and earth continuity wire. [E17:3a]

Supply & Fixing of 16A Modular type switch(brand approved by EIC) on existing GI modular switch box and making necy. Connections with PVC Cu wire and earth continuity wire.

Supply & Fixing 240 V, 21A Electron OLP 3+ starter power switch in Modular existing GI box with necessary connection with suitable size of copper wire as required.

Supply & Fixing 240 V, 25A Modular starter (Brand approved by EIC) on existing GI Modular type switch board with top cover plate and making necy. connections with PVC Cu wire & earth continuity wire etc. [For Outer light & Warter Pump]

Supply & Fixing 240 V, 25A Modular switch type SP MCB (C-Curve) (Brand approved by EIC) on existing GI Modular type switch board with top cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. [For Outer light & Warter Pump]

Supply and delivery of commercial type indoor mounting rail for SINGLE LED tube light frame [PHILIPS-TMC-501-P-1XT-LED-P3241/Eqv Jaquar Model/EIC Approved] complete with all accessories.

Supply and delivery of commercial type indoor mounting rail for TWIN LED tube light frame[PHILIPS-TMC-501-P-2XT-LED-P3242/Eqv Jaquar Model/EIC Approved] complete with all accessories.

supply and delivery of 1No. 4', 18W LED Tube]. [Philips: Master Led Tube 1200mm 18W-865 T8 IND -2100 lumen/ Eqv Jaquar Model/EIC Approved] for above tube frame fittings.

Fixing only single /twin LED tube light fitting complete with all accessories directly on wall/ceiling/HW round block and suitable size of MS fastener & flexible cord.

Fixing only LED tube light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports incl. S&F E.I conduit, ball socket/socket type ceiling plate and connecting the length of PVC insulated wire and necy enamel painting etc. as required by 2x24/0.20 mm (1.5sqmm) flexible copper wire of 1.10 mt. length.

Supply & fixing of Recessed mounted LED Down light with extruded aluminium housing and milky diffuser on existing false ceiling,the false ceiling should be cut as needed size ,if break the false ceiling then should be change it on an urgent basis. and the luminaries should be bounded with GI wire(4 side)properly from the trust as per direction of EIC and making necy. connections as required of the following specification. (2ftx2ft grid luminaries) [Crompton Polaris CDL/WW/Eqv Philips Make/EIC Approved].

Supply & Fixing of Slim design following sizes LED recessed round polycarbonate housing down lighter with superior light output and integral driver on the existing false ceiling. Efficacy 100lm/w.[Crompton Quartz Plus round CDL/WW /Eqv Philips Make/EIC Approved]. i)240V,15Watt(CDL/WW)

Supplying & Fixing bulk head light fitting (Havells make) with die cast aluminium housing & frosted glass on wall/ceiling incl. S&F 12 watts LED lamp complete set.

S/F 9 watt LED Lamp (B22 CDL) In the existing Holders. (Philips Ace Saver/Havells make) .

Supply & Delivery of 48",1200mm,230volt single phase AC ceiling fan incl. All acessories (blades,canopy,fork, rubber bush etc.) & the capacitor of the fan should be P-2 type burst proof & must have safety wire/rope directly from fan hook to stator of the ceiling Fan. [Crompton Alpha briz (brown)/Havells/EIC Approved]

Supplying & Fixing of Box type fan clamp of 150mm dia & 80mm depth made of 16 SWG CRCA sheet with one end duly sealed by cover, properly welded, incl. S&F 12mm dia 600mm long MS rod duly bent by heat treatment at the centre position of rod to grip fan bobbin properly, incl. binding the rod and fan box with reinforcement by 22 SWG steel binding wire, incl. supplying & covering the box with alkathene sheet, placed in order to prevent concrete from entering the box.

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire.

Supply & Fixing 240V, Modular Socket (2 Module) type fan regulator (Step type) (Brand approved by EIC) on existing Modular GI switch board with top cover plate incl.making necy. connections etc.

Supply of following spec,rpm-1420,230volt,metal body heavy duty exaust fan complete with all accessories.[EPC/havells heavy duty Ventil Air-DB/EIC Approved]. i) 9",230V,50Hz,1420rpm.

ii) 12",230V,50Hz,1420rpm.

Fixing only AC Exhaust Fan for Toilet use of 230mm/ 300mm sweep after making hole in wall and making good the damages and smooth cement finish etc. as practicable as possible and providing necessary length of PVC insulated wire and making necy. connection with flexible cord. i) 9"(inch),230mm.

ii) 12"(inch),300mm.

Supply & Fixing GI sheet (20SWG) metal Cowl with MS flat iron frame & GI wire mesh on wall with necy. bolts & nuts (6 mm dia x 62 mm long) i)For 9"(inch),230mm Ex-Fan.

ii)For 12"(inch),300mm Ex-Fan.

Supply and Delivery of 230V, 50Hz,1400 rpm AC Air bracket Air circulator 4 Blade wall Fan with necy. Allied all items. 450mm(18inch),85W.[EPC/Crompton/Havells/Orient/EIC Approved].

Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length.

Excavation of soil for installation of Earth Electrode and filling & ramming. For Morrum Soil.

Extra for treatment of soil by using salt & charcoal or coke for plate electrode.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. Long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. Long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. Long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. Below the ground level as below: a) By TATA-Medium GI pipe.

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 50 mm x 6 mm on wall having clearance of 6mm from wall incl. providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having 6 mm clearance from wall incl. providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required.

Supply & Fixing of LED outdoor street light fitting arm header, complete with all access. to be projected from the wall of the building incl. making drilled holes & providing clamping arrangement & necy.GI reducer as required.with Supply & Fixing of 40 mm GI pipe (Make :TATA-Medium) 1.5 mts. average length having suitable bend & necy nuts/bolts etc to provide necy.arrangement to fix the whole clamp arrangement & S&F necy. length of 3x1.5 sqmm(Ph,N,E) PVC insulated single core multi stranded annealed copper wire and making connections as required and mending good damages to wall incl. necy. enamel oil painting etc as required.

Supply & Delivery of 240V Warm white LED street light made up of pressure die cast aluminium housing with high power LED as lighting source with toughened glass top cover. TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with 10KV Built-in Surge Protection Device & temparature range should be 3000-4500K,manufacturer's warrenty should not be less than two(2) years. i) 240V,45W(Make- Crompton nexus+ LSTP/Philips/Bajaj)

Fixing only the street light/Flood light type luminaries in the exsting arm header by nuts bolts screw etc. incl. necy. connection as required.

Supply & Fixing of Moisture proof,water-proof (outdoor type) IP-66 protected PVC looping cable box (Hencel make/Eqv. EIC approved) size of 250mmx160mmx100mm (approx) deep having 2/3 mm thick body enclodure comprising of one 240 V,3/6/10/16Amp SP'MCB(as per site recuirement) on din channel ('C'-curve,legrand make),with 4way copper terminal and having lined with rubber gasketed top cover should be fixed on wall by screws,nuts, washers etc, necy. "cu" socketting, rubber gasketted entry and exit as mending with proper finishing is required as per direction of EIC.

SITC of Water Purifier of RO+UV with storage cooler of following specification : i). storage capacity : 80Ltr. ii). 60LPH water outlet of Emerson ECZ 444HG or Eqv compressor with R134A refrigerent. iii). Filtaration stages : 7. iv). RO Membrane 80 GPD x 4 Nos v). Permeate Production Capacity : 50 LPH. vi). Storage Tank Material: SS 304. Outer Body Material : SS 304. vii). No of Faucets : 2. viii). UV lamp : 8watt. ix). Iron Remover . x). ISO 14001 & 9002 factories & Certified for CE, NSF 53, NSF 42, WQA Gold seal ISI and CE certified products certificate of testing should be submitted at the time of installation. [EUREKA FORBES AG GREEN PURE CHILL 80 SS RO+UV-842121/EQV. EIC APPROVED]

Supply & Delivery of 7.5-TR capacity Multisplit type HVAC Air Conditioner unit (One Condenser Unit with 3 Nos. 4-way Compact Cassette type Evaporator unit ) of following specification : rated cooling capacity : 90,000 BTU/Hr. Outdoor compressor : 3 Nos Rotary type or advanced. refrigerant : R- 410A, Evaporator : 4-Way Compact Cassette of 3no. , each of 2.5Tr./ 9.0 Kw incl drain pump, Remote operated of 230V,50Hz,1-Ph . Condenser : 1no. of 415V,50Hz,3-Ph. Air-flow/per IDU:-1200CFM at (high level) or higher. (Make : Hitachi/O-General/Daikin/Mitsubishi Elect./Eqv. EIC Approved).

Lifting,Shifting,Installation,Testing & Commissioning of IDU & ODU of following capacities Multisplit Air Conditioners machines,after making hole in ceiling /wall on mending good the damages to the original finish as required & necy. scaffolding arrangement,labour cost etc.on both side(IDU & ODU Installation), and also connecting 4Nos. 10mm dia hanging rod from the ceiling must be attached into the machine by double nuts,bolts etc. as per requirement with incl. Supply of required Refrigerant R-410A ,S&F of necy. fixing arrangement for indoor & Outdoor duly painted etc. as per direction of EIC if required. [Exclud.outdoor structure cost] [For 7.5Ton Multisplit Unit Set]

Supplying fabrication & fixing of 2nos U-Channel (TATA Make) of size (75 mm x 50 mm x 50mm x 6mm thick) for making platform for instalation of outdoor unit of 7.5 TR Concealed type split AC incl. drilling 2nos holes in each channel as per site condition & as per direction of EIC. incl. cutting holes into the wall & grouting the same with cement concrete (1:1 %1/2: 3) etc incl. mending as orginal and fabricated with horizontal angle of 25 mm x 25 mm x 6mm including supporting angle 50 mm x50mm x 6mm in each platform in outer edge for transmitting the load centrally through 2Nos (50 mm x50 mm x 6 mm) Angle inserted to the exiting wall The entire structure should be baricated & safe for ODU maintenance Area of the platform is 2Mx1.2M. incl. scaffolding arrangement,labour cost etc.(Structural design should be approved from EIC.)[For 7.5Ton Multisplit Unit Set]

Supply & Fixing of Hanger Support for refrigerent pipe line by drilling holes into the ceiling & connecting 2Nos. 8mm dia hanging rod from the ceiling must be fixed by double nuts,bolts etc. as per EIC direction.

Supply & Fixing of Copper Refrigeration pipe line for liquid and suction line with fittings, elbows, bends, supports & brackets etc. with 9mm nitrile rubber tube with proper insulation tape required as per EIC direction. (Make- Ryoku/Totaline/Jobu/ Nippon/EIC Approved). i) Suction Line (5/8" OD with 0.7mm thick)

ii) Liquid Line (3/8" OD with 0.6 mm thick)

Supply and laying Control copper Cable (PVC insulated & unshethed,un-armoured) from Condensing Unit to IDU control panel/ Vice Versa if Required as per OEM (Make: Havells/RR Kable /finolex/EIC Approved ) i).4 core 2.5 sq mm cable. [3Nos. IDU to ODU + 2Nos. IDU to ODU ]

Supply and laying of Drain Water piping work out of PVC/ HDPE hard pipes of following sizes incl. fiting accessories "U"bends, elbows, tees flanges, tapings, wall sleeves hangers, supports, anchors etc. as required. (Make : Supreme / Astral/ EIC approved). i) 20mm/25mm.

ii) 32mm/40mm.

Supply & Fixing 415V,Three phase DOL starter for AC Controller 7.5Kw,13-21A O.L relay setting for 7.5Ton AC. [L&T MU-G10-SS95983COCO | 13 - 21. a compact set]

Supply & Fixing of Moisture proof,water-proof (outdoor type) IP-66 protected PVC looping cable box (Hencel make/Eqv. EIC approved) size of 250mmx160mmx100mm (approx) deep having 2/3 mm thick body enclodure comprising of one 415 V, 32Amp FP'MCB on din channel ('C'-curve,legrand make),with 4way copper terminal and having lined with rubber gasketed top cover should be fixed on wall by screws,nuts, washers etc, necy. "cu" socketting, rubber gasketted entry and exit as mending with proper finishing is required as per direction of EIC. [For 2Nos ODU]

Supplying & fixing of 415V, AC Control DB Fixed on Wall by flat iron/Angle frame or as per direction of EIC . The Box should comprising following accessories......... A).Double-door TPN-MCB Distribution Board with IP-42/43 protection 4 way make Siemens. B)1No 415V,32-40A FP-Modular Contractor(Make-L&T/Eqv. legrand). C)1No. 415V,32A FP-MCB(Make-L&T/Eqv. legrand). D)1 No. 415V Voltage Monitoring Relay(OV,UV,Timer delay setting,Phase failure).(Make-L&T/Eqv. legrand). E). 1No. 250V ,50Hz,16 Amp Digital daily & weekly time switches(Make L&T-67DDT0/Eqv. legrand) F)2Nos LED Indication Lamp for running condition. G)1 No. Toggle Switch(Pass & Seymour) should be fixed inside the box. H)The complete arrangement must be wiring by suitable size of PVC insulated Cu wire with suitable socket/lugs as per requirement & direction by EIC....

SITC of 1Nos. normal glow sign board (by LED Bulb) fabricated with 25x25x6mm m.s angle & 20mmx6mm M.S flat front side of the board making arrangement made with M.S angle incl. Provision for fixing the poly carbonate sheet facia approved color (3mm thick) with computarised lettering in blue base white lettering rigidly fixed on angle iron frame and 25mm x 25mmX3mm al angle with nuts bolts washers etc for fixing the facia backside incl. four side of the board cover with 20SWG al sheet ,water tight rubber gasketted etc.the facia should be illuminated with LED bulb,(quantity as per size of the board & recuirement to proper illuminate the board) incl. making arrangement for fixing the board incl. painting the inside of the board by synthetic enamel white coloured paint as per direction of EIC fixing the glow sign board on wall by cutting and making holes on wall for resting the sign board incl. 2nos MS angle incl drilling holes,nuts, bolts,washers,screws etc. as required to fix rigidly in wall as per direction of EIC) incl. mending good the damages to the original finish as per direction of EIC. (4FtX1.2Ft)

Add GST @18% On total from item no 1 to 69.

Add LWC @1% On total from item no 1 to 70.

KOUSHIK MONDAL (BID ID -5703801)

DURGAPUR POWER (BID ID -5690390)