CA NO. GE (P) KNS-13/2020-21

Amount

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep in soft /loose soil and getting out all as specified and directed by the Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in soft/loose soil all as specified.

Removal of excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point all as specified and directed by the Engineer-in-Charge.

Excavation in post holes in soft/loose soil each not exceeding 0.5 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with around earth in layers not exceeding 25 cm thick, watering and removing surplus spoil to a distance not exceeding 50 m and making good surface all as specified.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep in soft/loose soil, complete all as specified and directed.

M &L PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete all as specified

M & L brick work with sub class 'B' brick old size, straight or curved on plan exc 6 metre mean radius in CM 1: 6 all as specified.

M & L brick work with sub class 'B' brick old size, straight or curved on plan exc 6 metre mean radius in CM 1: 4 all as specified.

M & L Reinforced cement concrete 1:2:4, Type B-1, (nominal mix), using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified.

M & L Reinforced cement concrete 1:2:4, Type B-1, (nominal mix), using 20 mm graded stone aggregate as in roof slab all as specified.

M & L Reinforced cement concrete 1:2:4, Type B-1, (nominal mix), using 20 mm graded stone aggregate as in lintels over 1.5m span all as specified.

M & L Reinforced cement concrete 1:2:4, Type B-1, (nominal mix), using 20 mm graded stone aggregate as in columns, pillars, piers, posts & struts all as specified.

M & L Reinforced cement concrete 1:2:4, Type B-1, (nominal mix), using 20 mm graded stone aggregate as in beams all as specified.

M& L form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work n. exc 200 mm thick for rough finished surfaces all as specified.

M& L form work to edges of concrete flats and similar work exceeding 10 cm but n. exc 20 cm wide for fair finish surface all as specified.

M& L form work to sides of pillars, columns for rough finished surfaces all as specified.

M & L mild steel TMT bars 10 mm dia& over, cut to length, bent to shape required, including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified.

All as per item No. 17 here-in-before but TMT bars 6 to 8 mm dia

All as per item No. 17 here-in-before but 5 to 10 mm dia as in stirrups, spacers and binders

M & L rendering 15mm thick on other than fair faces of brick masonry in CM 1:4 finished the surface even & smooth without using extra cement all as specified.

M & L rendering 15mm thick on fair faces of brick masonry or concrete surfaces in CM 1:6 finished the surface even & smooth without using extra cement all as specified.

M & L rendering 15 mm thick in CM 1:3 as on ceiling finished the surface even & smooth without using extra cement all as specified.

M &L PCC 75 mm thick 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of flooring all as specified

M & L PCC 40 mm thick in 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring, finished the surface even and smooth without using extra cement all as specified

M & L PCC 75 mm thick 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection finished even & fair complete all as specified

M & L pressed steel frames 1.25 mm thick of size 105 X 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate etc all as specified.

M & L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in filling of chowkhat complete all as specified

M & L 35 mm thick factory made shutters, kiln seasoned and chemically pressure treated second class hard wood plain framed, panelled shutter ( two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part-I) complete all as specified

S & F mild steel barrel tower bolt, stove enameled black 150 mm long all as specified.

S & F mild steel sliding door bolts 250mm long plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate all as specified.

S & F mild steel pressed handles, oval type, stove enameled black 125 mm long all as specified.

S & F steel window with side hung shutter including projecting type hinges, with steel handles, steel peg stay with glazing bars, dovetailed or welded with one shop coat of zinc chromate primer all as specified. ( Glass for window shall be measured & paid separately)

S & F sheet glass 3 mm thick ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane all as specified.

M & L two coats of cement base paint over a coat of primer on newly plastered surfaces of walls including preparation the surfaces of walls all as specified.

M & L three coats of white wash on newly plastered surfaces of walls including preparation the surface of walls all as specified.

M & L three coats of white wash on newly plastered surfaces on ceiling including preparation the surface of walls all as specified.

M & L preparation of new steel surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint all as specified.

M & L preparation of new wooden surface of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified.

M &L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of flooring, path & paving all as specified

M &L PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in coping all as specified

S & F mild steel framed work confirming to Fe-410-0 or Fe-310-0 as in doors or gates of angle or other section with gusset plates, rails, braces, tee complete drilled for fixing of steel sheeting or other covering and fastening in position complete all as specified

Supply and fixing Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290 (Gde E-165) complete all as specified.

Supply and fixing Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified

Material and Labour for preparation of new steel and iron surface of any description and applying 2 coats of synthetic enamel paint over a coat of red oxide primer, surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified.

M & L treating small articles treating ends of posts, backs of chowkats, etc., area tarred exc 0.1 sq. m but n exc 0.5 sq. m each with tar or coal tar black paint all as specified

M & L 20 mm thick Granite (of any type) work (table rubbed and polished) on pillars in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick rendering in CM 1:6 all as specified

M & L PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in boundary pillars, posts (including caps & bases), foundation of compound wall etc all as specified

Supply & fixing Mild steel work of Fe-290 Gde E -165 as in angle iron fencing posts & flat iron drilled and countersunk for boulders running bars, including embedding in concrete and securing etc, post and struts in fencing including cutting, tops to shape as directed, bent to shape, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc.) Including all necessary drilling, bolting or riveting etc complete all as specified and shown on drawings. Note:- The element of Fixing of round bars for chain link fencing is included in this item .Nothing shall extra be paid on this account .

Supply and fixing Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia of barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins, etc all as specified and directed (Each line of wire shall be measured for payment purpose)

Supply only 4mm dia galvanised steel chain link fencing of size 50X50mm mesh, made-up into mattresses or cages, lapped, wired all as specified

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and shown on drawings. ( Note :- supply only Chain link for fencing will be measured and paid separately )

Supply only 10mm dia MS round bar for fixing of chain link fencing with post complete all as specified and directed. Note :-Fixing element of this item is included in serial item no. 43 here-in-before.

Supply and fixing flat iron for fixing of chain link fencing etc. conforming to Fe-290 (Gde E-165) complete all as specified.

Material and Labour for two coats of synthetic enamel paint over & including a coat of red oxide pink primer over new wooden surfaces of any description, exceeding 10 cm in width or girth including preparation of surfaces complete all as specified.

Supply and fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long but n exc 10cm , Diameter of neck 16 to 20 mm complete all as specified and directed

All as per item No. 55 here-in-before but exc 30 cm long , diameter of neck exceeding 12mm and not exceeding 20mm

M & L PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in seismic and other similar bands complete all as specified

Supply and fixing Mild steel Hand rails, half round or other stock section , drilled and countersunk for balusters running bars, and similar work conforming to Fe-290 Gde E-165 all as specified.

Material and Labour 60mm thick machine pressed precast concrete coloured inter locking paver block with Grade of M-35 conforming to IS 15658-2006 any size and shape, over 25 mm thick sand cushioning complete all as specified and directed . Note :- Tiles shall be approved by GE in writing before incorporation in work.

Material and Labour Factory made hydraulic Pressed Precast Cement Concrete kerb stone in 1:2:4, type B-1, using 20 mm graded crushed stone aggregate and set and jointed in cement mortar 1:4 complete all as specified. Note: The rate of form work is included in this item and nothing shall be paid extra.

S & F concertina coil with punched tape 900 mm dia, having 50 rounds per 6 metre length, with wire diameter 2.5 mm and blade size 15 mm x 12 mm x 0.5 mm, spacing of blade 26 mm, fixed in position over walls complete all as specified and as directed by Engineer-in-Charge.

M/s HANS BROTHERS

K L JINDAL AND CO.

M/s GURFATEH BUILDERS

SJM CONSTRUCTIONS

M/s Abnash Kumar Bholla

Singla Enterprises

SAPNA BUILDERS