CIVIL WORK

Amount

R&R work of officer rest house building at 220KV, S/S, BBMB, Dhulkote.

Dismantling concrete. (e)Reinforced cement concrete Pb. CSR Ref No.-8.6(e)L/R

Dismantling concrete. (d)Cement concrete plain1:2:4mix. PbCSR Ref No-8.6(d)L/R

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. Pb.-CSR Ref No.-11.6-T/R

Scraping.(c)Cement plaster. PbCSR RefNo-8.31(c)T/R

16mm thick cement plaster 1:4 in two coat work. Pb.-CSR Ref No.-15.16-T/R

Top Khurra 0.6mx0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50.00 thick cement concrete 1:8:16. Pb.-CSR Ref No.-13.45-T/R.

Bottom khurra on ground 1.2m 0.6m consisting of bricks on edge laid in cement mortar 1:3 over 7.5cm cement concret 1:8:16 including 12.5mm thick cement plaster 1:3. Pb.-CSR Ref No.-13.51-T/R.

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified. Pb.-CSR Ref No.-13.55-T/R.

Washed stone grit plaster on exterior walls of height upto 10 M. above ground level in two layers, under layer 12.5mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2the under layer with scratching tool, applying cement slurry on the under layer @2 as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings, complete as per specification and direction of Engineer-in- charge (Payment for providing grooves shall be made separately). Pb.-CSR Ref No.-15.70-T/R.

Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens,nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge: 20 mm wide and 15 mm deep groove. Pb.-CSR Ref No.-15.72-T/R.

Finishing walls with acrylic smooth exterior paint of required shade with two or more coats applied @1.67 litre/10Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm. Pb.-CSR Ref No.-16.59-T/R.

Repair of damaged RCC slab ceiling at various portions by concreting, plastering and reinforcing with chicken mesh and M.S flat 40x6mm strips laid @225mm c/c, jointed with ceiling by fasteners complete in all respects to the entire satisfaction of Engineer-in-charge. (NS Item).

Repair and replacement of Club House building at 220KV, S/S,Dhulkote.

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled. (a)Doors of area 3 sqm and below. Pb.-CSR Ref No.-8.26(a)-L/R

Removing Doors and Windows (Steel or wood)with chowkhats by making recesses in walls when the wall is not to be dismantled. (b)Windows of area 3 sqm and below. Pb.-CSR Ref No.-8.26(b)-L/R

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled. (c)Clerestory windows of area 3 sqm and below. Pb.-CSR Ref No.-8.26(c)-L/R

Dismantling concrete. (e)Reinforced cement concrete. Pb.-CSR Ref No.-8.6(e)-L/R.

Stripping and stacking iron sheets of a roof including ridging, flashing, eaves boards gutters and down pipes. Pb.-CSR Ref No.-8.11-L/R.

Nicking cement concrete surface (over 28 days old including preparation and laying slurry. Pb.-CSR Ref No.-10.31-L/R.

Conglomerate floor 40mm thick cement concrete topping 1:2:4 using mechanical mixer for mixing of material.Ref-14.6-T/R.

Providing & fixing glass strips 3mm thick in floor (a) 40mm wide. Pb.-CSR Ref No.-14.104(a)-T/R.

20mm thick grey polished skirting or dado consisting of bottom layer of 16mm thick cement sand plaster 1.3 and finished 3mm thick topping of neat cement rubbed and polished including rounding of junction with floors. CSR Ref No.-14.16-T/R.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins,rafters and trusses and including cutting to size and shape wherever required. (a)0.50 mm (+ 0.05 %) thick. Ref No.-13.27(ii)(a)-T/R.

Ridges and valleys 45 cm overall, in plain G.I. Sheet 0.80mm fixed with galvanzed iron J. and L. hooks 10mm diameter, G.I. Limpet and bitumen washers complete. Pb.-CSR Ref No.-13.21-T/R.

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. Pb.-CSR Ref No.-11.6-T/R.

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for separately): (a)For fixed portion and chawkhats. Pb.-CSR Ref No.-17.45(a)-T/R.

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS :1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including leat angle, aluminum snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In-Charge. (Glazing and paneling to be paidfor separately): (b) For shutters of doors, windows & ventilators including providing andfixing hinges/ pivots and labour for fixing of fittings wherever required including the cost of PVC Plug /neoprene gasket required. Pb.-CSR Ref No.-17.45(b)-T/R.

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-In-Charge. Prelaminated particle board with decorative lamination on Both side. Pb.-CSR Ref No.-17.46(ii)-T/R.

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item). (ii) Float glass panes of 4mm thickness. Pb.-CSR Ref No.-17.47(ii)-T/R

Cost of aluminum fittings complete for doors, windows such as tower bolts,handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt). (ii)For shutter area above 0.50 sqm. Pb.-CSR Ref No.-17.23(ii)-T/R

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with nuts and screws etc. complete: (b) 250mm x 16mm. Pb.-CSR Ref No.-17.49(b)-T/R

12.5 mm thick cement plaster 1:5. Pb.-CSR Ref No.-15.10-T/R

Scraping. (a) White wash and colour wash. Pb.-CSR Ref No.-8.31(a)-L/R

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish. Pb.-CSR Ref No.-16.65-T/R

Finishing walls with cement based water soluble exterior paint such as snowecem, robbiacem etc. on old work one coat to give an even shade. Pb.-CSR Ref No.-16.14-T/R

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats on old distempered work when shade is changed. Pb.-CSR Ref No.-16.12-T/R

RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES:Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket &plug control point) and other petty material etc., including the cost of above material,cutting and filling up of chases (with finishing the surface):- (ii) Wiring light point. Pb.-CSR Ref No.-34.02(ii)-T/R

(iii) Wiring call-bell point. Pb.-CSR Ref No.-34.02(iii)-T/R

(iv) Wiring 6Amp. wall socket point. Pb.-CSR Ref No.-34.02(iv)-T/R

(vi) Wiring 16/20Amp. power plug control point. Pb.-CSR Ref No.-34.02(vi)-T/R

(vii) Wiring light point without control switch. Pb.-CSR Ref No.-34.02(vii)-T/R

R&R of Vehicle Shed in the colony at 220KV, S/S, BBMB,Dhulkote.

Stripping and stacking iron sheets of a roof including ridging, flashing, eaves boards gutters and down pipes. Pb.-CSR Ref No.-8.11-L/R

Structural steel work in angles, tees, flats, riveted, including cutting, fixing all gusset plates, bolts,nuts, rivets etc. with hoisting and erecting in position. (a)For roof truss, well curbs, plate girders etc. of any span for building for bridges upto 15M span. Pb.-CSR Ref No.-18.3(a)-T/R

Nicking cement concrete surface (over 28 days old including preparation and laying slurry. Pb.-CSR Ref No.-10.31-T/R

Cement concrete 1:2:4. (a)With stone ballast or shingle. (ii)mixing by mechanical means using concrete mixer volumetric type. Pb.-CSR Ref No.-10.13(a)(ii)-T/R

Providing and filling joint sealing compound with coarse sand and 6 percent bitumen by weight complete as per drawings and technical clause 2605 of MORT&H specifications. Pb.-CSR Ref No.-24.61(b)-T/R

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins,rafters and trusses and including cutting to size and shape wherever required. (b) 0.60 mm (+ 0.05 %) thick. CSR Ref No.-13.27(ii)(b)-T/R

First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level. Pb.-CSR Ref No.-11.4(i)-T/R

12.5 mm thick cement plaster 1:5. Pb.-CSR Ref No.-15.10-T/R

White washing work in various Resi. & Non-resi. Buildings situated at 220KV, Sub-station, BBMB, Dhulkote.

Scraping: (a) White wash and colour wash. Pb.-CSR Ref No.-8.31(a)-L/R

Distempering with Acrylic washable oil bound distemper (of approved manufacture) one coat over one priming coat on old distempered surface. Pb.-CSR Ref No.-16.11-T/R

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish. Pb.-CSR Ref No.-16.65-T/R

Finishing walls with cement based water soluble exterior paint such as snowcem,robbiacem etc. two or more coats to give an even shade. Pb.-CSR Ref No.-16.13-T/R

White washing (two or more coat). Pb.-CSR Ref No.-16.2-T/R

RELIABLE ENGINEERS

Ms. Paramdeep Singh