SPECIAL REPAIR OF BLDG NO H-7F SINGLE JCOs ACCN AT COD ESTATE UNDER GE (I) KANPUR

Amount

Taking down chowkats without taking off shutter from chowkats area n.exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area exc 1.5 Sqm and not exc 4 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but n exc 2 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but n exc 2 Sqm each and re-fixing in the same opening complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

M&L MS Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing, conforming to Fe 410 W (Gde-E-250) quality A complete all as specified and as directed.

S&F 1.25 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including, steel gates and similar work, cut size, holes punched; including round headed screws, and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded , including bending or turning up, mitred angles, etc. as required. complete all as specified and directed.

S & F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S &F 30mm thick glazed and skeleton shutter of 2nd class hard (Hollock) prepared to receive gauge/glass (without sash bars ) fixed with mitred beads and securing glass gauge etc sizes of members of shutter as specified in SSR part-1 section-8 ,clause 8.24(a) complete all as specified and directed.

S & F 100mm size mild steel, butt hinges, medium weight, cold rolled and fixed with mild steel screws complete all as specified and directed.

S&F 200mm long barrel tower bolt of aluminium extruded section complete all as specified and directed.

S&F 150mm long handle of aluminium extruded section fabricated anodized type complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section & fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F 150mm floor door stopper of aluminum alloy body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F powder coated aluminium anodized three track three panels sliding window, shutter glazed and gauged of stainless steel wire cloth nominal dia of wire 0.36mm and average width of aperture 1.40mm along with aluminium section with 50 micron anodizing size of frame 100mmx25mmx16 gauge, size of shutter, top, bottom and side rail 19mmx38mmx16 gauge aluminium section with 50 micron anodizing and 5mm thick black / tinted sheet glass to be fixed on glazed portion and necessary stainless steel hooks and eye to be provided as stay of shutter etc complete including necessary jointing cleats, glazing clips, rubber packing attached aluminium snap beading, screws anodized aluminum fitting such as suitable handle & auto locking arrangement etc complete all as specified and directed.

S & F powder coated anodised aluminium ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

M&L for aluminium grill of mesh size 65 x 75mm of 6mm dia of aluminium bar fixed with 'Y' or 'H' aluminium sec complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube incl suitable metal stifner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed.

S & F factory made solid panel PVC moulded door shutter 28 to 30 mm thick (styles) with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm prelam PVC sheet on back face with particle board core complete all as specified and pattern & design complete all as specified and directed.

S & F PVC handle 150mm size complete all as specified and directed.

S & F PVC but hinges 100mm size complete all as specified and directed.

S & F PVC tower bolt 150mm size complete all as specified and directed.

S&F in repairs fancy type stainless steel curtain rods of 25 mm dia for doors/ windows etc including SS brackets and SS funnels/dome complete all as specified and as directed.

Dismantling wall or ceiling boards (fibre, pulp insulation etc) any thickness & at any height including fittings/grids etc complete all as specified and directed.

S&F aluminium anodised snap grid frame work of size 605x605mm for false ceiling with 4mm dia suspesion wire MS @1200mm c/c complete all as specified and directed.

M & L for providing Gypsum Board 12mm thick, 600 x 600 mm in size, fixed or laid/ inserted to timber/GI/Aluminium frame work as in ceiling, fixed with screw as per manufacturers instructions including two coats of OBD over a coat of primer on ceiling boards complete all as specified and as directed.

Demolition of unreinforcement cement concrete of any description and in position not otherwise specifically provided for complete all as specified and directed.

Demolition of plain cement concrete in ground floor and pavings not exc 15cm thickness below or above ground level complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified. (Note : Debris obtained from dismantling will be dispossed off as directed)

M&L for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in copings, kerbs, filling for fixing of hold fast etc including necessary formwork etc complete all as specified and directed.

M&L 40mm thick PCC (1:2:4) type B-1, (using 20mm graded stone aggregate) as in floor to receive tiles complete all as specified.

M&L for non skid joint free ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the suraface over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per Item No (32) here-in- before but as in skirting over and including 10 mm thick rendering in CM (1:4) all as specified and as directed.

M&L for non skid joint free ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the suraface over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per Item No (34) here-in- before but as in skirting over and including 10 mm thick rendering in CM (1:4) all as specified and as directed.

M&L for glazed ceramic tiles coloured, joint free in vertical surface 300X 450X 7mm thick mm thick as on walls over and incl 10mm thick rendering in cement mortar (1:4) and jointing in neet slurry and pointing in coloured cement to match the inside of tiles all complete as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, approns etc laid, bedded and pointed in any mortar complete all as specified and directed. (Note : Debris obtained from demolition will be dispossed off as directed)

Material and labour for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms/slabs and like laid over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite half round on exposed projected surfaces all as specified and as directed.

M&L 75 mm thick Cement concrete type D 2, 1:4:8 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and as directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness , M-35 grade, set, jointed over and including 25 mm thick sand cushoning complete all as specified and directed.

Providing precast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in cement mortar complete (1:4) with joints to match complete all as specified and directed.

M&L for non skid coloured heavy duty parking tiles of size 300x300x9-10 mm thick impact resistance over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 75 mm thick PCC (1:3:6) type C1(using 20 mm graded stone aggregate) as in plinth protection and paving laid in alternate bays finished finish even and smooth wihtout using extra cement complete all as specified and as directed.

Demolition of brick work of any description and in any position built in cement mortar including quoins arches and pillars complete all as specified.

M&L for brick work with fly ash old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 for manholes, drains, septic tanks, soak wells etc. complete all as specified and directed.

Taking down cement plaster on bricks including raking out joints hacking for key scrubbing down with water etc.complete all as specified and directed.

M & L 15mm thick rendering in cement mortar 1:6 on brick or concrete surfaces of wall even and smooth complete all as specified and directed.

M & L 15mm thick rendering in cement mortar 1:4 on brick or concrete surfaces, mixed with water proofing compound as per manufacturer's instructions, surfaces finished even and smooth complete all as specified and directed. Note:- WPC measured and paid separately.

M&L for 10mm thick cement plaster on ceiling in CM 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

Dismantiling of concrete by chiselling from RCC members like col, beam, parapet, facia, ceiling etc exposing the reinforcement without disturbing the reinforcement and get free from rust by sand blasting providing at places addl reinforcement welding with existing reiforcement as directed wherever required binding with welded mesh 100 mmx100mm (12 gauge welded mesh) & tack welding and primed with using Araldite epoxy resins ( manufactured by M/s Ciba Geigy Ltd/ FAIR BOND EP/Sika or other approved manufacture) & provision of guniting pressure 2 to 3 Kg/Sqm with admixer 1 cement 3 sand mixed Dr fixit Pidicrete SC plasticiser (2 to 10% by weight of cement) of thickness 40mm average including stripping, floating with wooden strippers for proper dimension control inclusing necessary form work & scaffolding up to Three storey complete and surface of guniting to be finished fair and even with and including 10 mm thick plaster in cement mortar 1:4 with water proffing compound @3% by weight of cement, cleaning & removing of waste material etc as directed at site including necessary painting,white wash, distemper/ exterior acrylic emulsion). All surrounding wall, joineries and fitting should be covered with polythene sheet by contractor while work. (Any wall, floor,fittings and roof damaged by the contractor shall be repaired/change by contractor under same item and no extra payment will be paid to contractoron this account complete all as specified and directed. Note: Welded mesh & addl reinforcement if required measured and paid separetly.

M&L for preparation of new plastered surfaces and applying three coats of white wash as on ceiling surfaces complete all as specified.

M&L for preparation of new plastered surfaces and applying three coats of white wash as on wall surfaces complete all as specified and directed

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper on surfaces of wall over a coat of primer and wall care putty for getting smooth surface complete all as specified and directed.

M&L for complete removal of existing treatment from surface of walls and preparation of old plastered surfaces and applying two coats of oil bound distmper of any colour on old surfaces of wall over a coat of primer and wall care putty for getting smooth surface complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coat of weather coat exterior paint on wall surfaces over a coat of primer and wall care putty for getting smooth surface complete all as specified and as directed.

M&L for complete removal of existing treatment from surface of walls and preparation of old plastered surfaces and applying two coats of exterior emulsion paint (weather proof anti algae) over a coat of primer and wall care putty for getting smooth surface complete all as specified and as directed.

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide & over 10cm width or girth complete all as specified.

M&L for preparation of new wooden surfaces width or girth exc 10 cm and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified .

M & L preparation of old steel surfaces of any description over 10 cm width or girth and apply two coats of synthetic enamel paint complete over truss purlin etc all as specified and directed.

M&L for Cutting chases, pinning in. making good to facings for concealed water tubing n exc 10cm grith and making good with cement mortar 1:3 complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15 mm bore galvanized steel tubes medium grade with all fittings laid concealed/surface in walls complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified.

S&F 20 mm bore galvanized steel tubes medium grade with all fittings laid in walls complete all as specified.

Dismantling PVC water tanks of capacity exc 250 ltr but n exc 500 ltr and removing to store complete all as specified and directed.

S&F HDPE triple layer rotational moulded polyethylene water storage tanks in white colour (cylindrical vertical with closed top) 500 litres capacity hoisted and fixed in position all as specified in SSR Pt-I including for hoisting into position either inside or outside of building, connecting up pipes, securing access cover etc including GI nipple of suitable size complete all as specified and directed.

S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed 20mm bore complete all as specified.

S&F in repairs 20mm dia of bore Gun - metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed.

S&F in repair vitreous china WHB white flat back size 550x400mm complete all as specified and directed.

S & F 600 mm x 450 mm bevelled edge mirror, mounted on 6 mm thick plywood and fitted to wooden plugs with CP brass screws and cup screws including taking down old unserviceable mirror complete all as specified and directed.

S&F in repair vitreous chinaware EWC water closet pan (Padestal pattern), white with and including white seat & cover with flat bottom with CP hinging device complete all as specified and as directed.

S & F in repair vitreous china squatting pan 'Orrisa pattern' size 580x440mm white with integral foot rests any pattern and making connection with & including CI P/S Trap, etc complete all as specified and directed.

S&F in repair of PVC low level flushing cistern white 10 Ltrs capacity with inlet 15mm bore ball valve, float and handle incl brackets, incl PVC connection 300mm with flanges at both ends screwed down to 15mm bore pipe and 32mm bore PVC flush pipe of required length complete incl taking out of existing flushing cisterns complete all as specified and directed.

S&F in repairs Chromium plated brass soap dish/ tray fixed with wall complete all as specified and directed.

S&F in repair 15mm bore CP fancy type bib tap with capstan head including flange complete all as specified and directed.

S&F in repairs 15mm bore CP fancy type bib tap two way with capstan head fixed complete all as specified including flange complete all as specified and directed.

S&F in repair stop valve concealed type 15mm bore of cast copper alloy,fancy type of CP with long shank and cup,high pressure screwed both ends for iron pipe or unions and fixed complete all as specified and directed.

S&F in repair 15mm bore chromium plated stop valve/angular cock screwed down high pressure with capstan head and flange complete all as specified and directed.

S&F in repairs pillar taps fency type (ISI marked) cast copper alloy CP with capstan head, screwed down high pressure with or without lettered HOT or COLD with long screwed shanks and fly nut screwed for iron pipe of 15mm bore all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges incl brackets complete all as specified and directed.

S&F in repair hand shower (health faucet) with 8 mm dia 1 mtr long flexible tube and wall hook chromium plated complete all as specified and directed.

S&F in repair 80 mm dia shower rose, brass chromium plated with swivel joint complete all as directed.

S&F in repair sinks with drainage board of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including waste coupling.

S&F in repairs stainless steel plate rack made out of 1mm thick stainless steel of overall size 750x900mm including fixing with brackets/clamps with screws pattern & design as approved by GE complete all as specified and directed.

S&F in repair stainless steel gratings suitable for 100 mm floor trap complete all as specified and as direcred.

S&F in repair PVC waste pipe 32/40mm dia suitable for Sink/Urinal etc complete all as specified and directed.

S&F in repair PVC connection 450mm long brass chucknut bolt ends for fixing 15mm dia pipe complete all as specified and directed.

Demolition of reinforced cement concrete of roofs, floors (other than ground floors) beams staircases landing chajjas and similar suspended work etc complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as directed.

M&L for mild steel deformed TMT bars 10mm dia and over (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for RCC 1:2:4, type B1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Dismantling of 75 to 100 mm dia cast iron or reinforced concrete drain pipes incl bends etc, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

S & F 75 mm bore cast iron soil, waste and vent sand cast pipes in any length with or without ears, with cement joints, laid in floor/trenches or in floors all as specified and as directed.

S & F 100 mm bore cast iron soil waste & vent sand cast pipes in any length with or without ears, with cement joints, laid in floor/trenches all as specified & directed.

S&F 100 mm bore cast iron soil waste & vent sand cast pipe in any length with or without ears, with cement joints, fixed on walls with MS flat iron clamps size 50 x 6mm and 16mm dia round bar stay of required shape and size inclduing drilling holes and embedded in CM 1:3 surface finished complete all as specified and as directed.

S & F 75 mm bore cast iron bend ( any radius ) diminishing pieces or tapers (larger bore measured) all as specified and directed.

S & F 100 mm bore cast iron bend ( any radius ) diminishing pieces or tapers ( larger bore measured) all as specified and direced.

S&F in repair 100mm bore cast iron vent cowl complete all as specified and directed.

Dismantling of boarding, any descripsion, fixed in any position with nails all as specified and directed

M & L 18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

All as per Item No 100 above but fixed in shelf and partition, ceiling etc.

S & F Continuous (piano) hinges, mild steel, bright finish or elecro galvanised width of flaps when open in 30 mm complete all as specified and directed.

M & L 125mm size stainless steel handles complete all as specified and directed.

S & F 125 mm size aluminium anodised hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as directed.

Dismantling of asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges complete as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L Mild Steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410 W (Gde-E-250) quality A complete all as specified and as directed.

S&F Mild Steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes with riveted, bolted or welded attachment etc incl mild steel screw bolts (machine made) with hexagonal or square heads at one end & washers as reqd conforming to Fe 410W .Gde-E-250, quality-A complete all as specified and directed.

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws of required size and dia complete all as specified & directed

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws of required size and dia complete all as specified and directed.

S&F Mild Steel wind ties for roof including securing bolts as directed, including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Demolition brick tile/cement concrete tiles / APP membrance by using hand held electric drills, cutting machine, chisels etc (direct use of hammers on RCC roof for demolition is strcitly prohibited) of roof treatment including padding concrete of any description including mud in roof any thickness with and including roughening old concrete surfaces by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed by the Engineer-in-charge.

M&L for cement concrete type B0 (1:2:4 ) using 12.5 mm graded stone aggregate as in padding, coping, roof kerb incl hunching, benching etc complete all as specified and directed.

M&L for 10 mm thick in CM(1:3) rendering on fair faces concrete surfaces/roof top mixed with liquid water proofing compound finished even & smooth without using extra cement complete all as specified and directed. Note : Liquid WPC shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed. Make Dr. Fixit or equivalent.

M&L water proofing treatment to roof slab with APP modified polymeric membrane thickness not less than 3 mm plain membrane (weight of membrane not less than 3.50 Kg +/- 5% per Sqm) and weight of centre core polyster mat shall be 160 gram +/- 15% per Sqm and lower side finished with 10 to 15 micron thermo fusible polyethylene complete all as specified and directed by Engineer-in-Charge with following courses of descriptions below :-Make of membrane shall be SIKA/Super Thermolay APP (STP) / IWL as approved by GE. (a)The surface of roof, parapet and gutters and drains mouth etc over which waterproofing treatment is to be applied shall be thoroughly cleaned of all foreign matter, moss dust etc by wire-brushing and dusting. For cast iron/PVC drains outlets a grove shall be cut around to tuck in the treatment. Concrete angles-fillets provided at junctions between roofs and verticals faces of walls (parapet and other walls) around obstacles such as pipe, chimney stacks etc and other similar situation to ease up about corners. (b) On the prepared surface one coat of Solvent based bituminous primer (Sika® WP shield Primer or other techno commercially Equivalent make of STP/IWL ) shall be applied @ 0.35 to 0.50 Kg/sqm till the surface is properly impregnated. The time delay of laying of membrane after application of primer shall be as per manufacturer instructions. (c) Laying of polymeric waterproofing membrane and bonded completely to the substrate & the overlaps are then sealed /fused by flame torch as per manufacturer instructions. (d) The overlaps shall be of minimum 4 Inch (100 mm) side lap and 150mm at end ,sealed by the flame-torch. The contractor shall submit a gurantee of 10 years from the date of completion of work for waterproofing treatment alongwith manufacturer's gurantee. The amount of Rs. 25 ( Twenty Five ) per Sqm and min of Rs. 2500/- for waterproofing treatment shall be withheld from contractor's final bill till the expiry of gurantee period. The contractor at his own option may furnish fix deposit receipt pledged in favour of GE(I) Kanpur against guarantee money.

M&L for preparation of new surfaces and applying two coats of aluminium paint over a coat of aluminium primer on membrane, over 10cm in width or girth complete all as specified.

Dismantling of unframed work timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bell, bell push etc and making good disturbed surfaces of walls, floor to match with existing specification complete and all as specified.

Point wiring for one light point/fan/bell point controlled by one switch with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green color) as earth lead in and including concealed non metalic rigid PVC conduit medium grade size 25 mm dia with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size & as directed & 3 mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed.

All as per srl item 120 above but upto ceiling height and on surface at ceiling complete all as specified and directed.

All as per srl item 120 above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and incl conduit complete all as specified and directed.

All as per srl item 120 above but for one 3 pin 5A socket outlet independent controlled by one switch complete all as specified and directed.

All as per srl item 120 above but for one 5A socket outlet on the same board controlled by one switch complete all as specified and directed.

M&L for switch piano flush button single pole one way 5/6 amps 240 volts complete all as specified and directed.

M & L for switch piano flush button single pole one way 15/16 amps 240 Volts complete all as specified and directed.

M&L for socket outlet 5 amps 5 pin flush type, 240 volts complete all as specified and directed.

M&L for socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type, 230 volts complete all as specified and directed.

M&L for ceiling rose surface bakelite 3 terminals complete all as specified and directed.

S & F Lamp holder insulated body with back plate for dome batten fittings complete all as specified and directed.

Supply and fixing in replacement fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically complete all as specified and directed.

M&L in replacement for submain wiring with four single core PVC insulated flexible copper conductor multistranded cable (FRLS) of size 6 Sqmm with proper color coding and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 4 Sqmm as earth lead in & including concealed PVC conduit medium grade 32mm dia cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

S&F in replacement of wall mounted LED light fittings 20 watt (not less than 100 lm/W) , 6500/3000K, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver complete connecting electrically complete all as specified and directed.

S&F in replacement of LED mirror light fitting min 10 Watt Watt,2' long, with smart motion sensor,extruded aluminium heat sink for efficient heat dissipation and integrated electronic driver complete connecting electrically complete all as specified and directed.

Supply and fix in replacement of High power LED street light 25 Watt Energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs as light source and electronic driver incl suitable size service bracket fixed with clamps, nut, bolt and washer and electric connection with 1.5 Sqmm multistranded twin core alum cable PVC insulated complete all as specified and directed.

S & F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 IK-09 protection with metal door single phase 240 volts, 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

S & F distribution board iron clad, double door with IP-43, IK-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/s VTPN DB 4 way, complete with appropriate size copper bus bar and neutral link, complete with one MCCB 3 pole 415 Volts 125 Amps rating with rupturing cap 25 kA of the same make as of distribution board & with MCBs of required size making connection with thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site complete all as specified and directed.

M&L for MCB single pole 240 volts 6 to 10 amps, with rupturing capacity 10 kA using thimbles of required size complete all as specified and directed.

M&L MCB single pole & neutral 240 volts 32 amps,with rupturing capacity 10 kA using thimbles of required size complete all as specified and directed.

M&L for single pole and neutral enclosure with a top pin, earth plug and socket complete with one SP MCB 25 Amps, 240 Volts complete all as specified and directed.

M&L for RCCB ,double pole,single phase 240 volts , rated current 40 amp, sensitivity 30 mA complete using thimbles of required size complete suitable for fitted in DB complete all as specified and directed.

S & F Ceiling fans complete with blades, complete with down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 200 CFM with BEE 5 star rated with brushless direct current motor (BLDC) complete all as specified and directed complete all as specified and directed.

S & F Hot water heater storage type 25 ltr Cap, 5 star rated with fast heating upto max wattage 2000 watt,pressure upto 8 bar,with capillary thermostat and automatic thermal cut off safty anti rust design,with 5 yr warantee on MS Tank with Stainless steel heavy duty pipe of suitable length for hot water supply with two nos nut adapter ISI marked complete all as specified and directed.

Supply and install of fresh air fan(ventilator) 240 V ,AC single phase of size not less than 200 mm sweep ,900 rpm, plastic body complete with fixing arrangement ,electric connection incl with rubber mounting for silent operation, grouting of nuts, bolts,in wall/ventilator,complete all as specified and directed.

M & L for providing earthing with GI earth plate electrode 600 X 600 X 6mm buried directly in ground (earth pit not less than 2.25M deep below ground level ) with top edge of the earth plate not less than 1.5M below ground level connected to galvanised earth lead wire 4.0mm dia by means of nuts,bolt,washers etc.of copper / brass connected to earth test point complete all as specified in electrical plate NO 3 of SSR1996 part 1 ,including necessary excavation and earth work in any strata of soil,GI water pipe with 20mm dia.funnel &wire mesh PCC pit with CI cover and frame etc all as specified and directed by Engineer-in-charge. Note:- All the joints shall be made with welding to get proper conductivity.

Disconnecting Electrically and taking out old unsv LT UG cable any type of size upto 50 sqmm 3.5 Core complete all as specified and directed.

Supply and Laying in trenches or fixing to wall /pole or passing through pipes insulated heavy duty electric cable with alluminium conductor 1100V volts grade cross sectional area 50 sqmm 3.5 Core complete all as specified and directed.

Excavation in trenches in any type of soil n exc 1.5 mtr in width and n. exc 1.5 mtr in depth and getting out all as required for laying of cables,foundation filling of poles or stays and for rerouting of cables complete all as specified and directed.

Returning filling, in including spreading ,leveling, watering and well ramming in layers not exc 25 cm each complete all as specified and directed.

Removing excavated material to a distance not exceeding 50 meters and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed.

M&L for Sub class ‘B’ bricks old size. laid dry flat over the cable abutting each other, length of cable equal to width of brick complete all as specified and directed.

M/S AADI ENTERPRISES

Preetpowercontrol

JOG CONSTRUCTION

M/s DKS Engineering Works

J.B.ENTERPRISES

Khalil Ahmed and Sons

ESKEY COMPANY