CA NO. GE/CHM-91/2024-2025 SPL REPAIR TO BLDG NO P 982 MI ROOM AT CHANDMANDIR MIL STN

Amount

Dismantling of existing brick tiles or terracing tiles single layer on roof grouted in cement mortar including removal of any existing treatment complete all as specified & directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing all demolished material complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Demolition of stone slabs of any description in floors laid, bedded and pointed in any mortar complete all as specified and directed

Demolition of cement concrete (un-reinforced) in ground floor and paving n.exc 15cm thickness (below or above GL) as in plinth protection/ path/ Hard standing/ floor etc. etc complete removal of debris outside MD land.

Demolition of reinforced cement concrete in roofs, floors, beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Taking down cement plaster from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete all as specified and directed and removing rubbish etc. complete all as specified and directed.

Plain cement concrete 1:7:12 type F-2 using 40mm graded brick coarse aggregate as in sunken floor filling and mass concrete complete all as specified & directed.

Water proofing treatment to sunken portion and adjoining walls of kitchen, WC, Bath & Toilet, etc, as follows, complete all as specified & directed :- (a) 15 mm thick plaster in cement mortar (1:3) mixed with WP compound as per manufacturer's instructions shall be provided on sunken portion after roughening of surfaces. (b) Apply cement slurry to the surface @ 0.488 kg /Sqm of cement mixed with Acrylic based polymer modified cementious composite compound @ 0.253 kg/Sqm and the surface will be allowed to air cure for 4 hours. (c) Apply another layer of cement slurry @ 0.242 kg/Sq. m of cement mixed with Acrylic based polymer modified cementious composite compound @ 0.126 Kg/Sq. m and the surface will be allowed to air cure for 4 hours. (d) Pond curing of sunken portion for minimum of 48 hours. (e) Paste one layer of 3mm thick APP membrance with bitumen by torch application to the the treated sunkensurface. (f) Joints/ traps /WC /soil pipes shall be properly sealed with approved sealing compound.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

304 grde stainless steel railing for stair case consisting of stainless steel pipes of different dia including socket, reducer, knobs ball and cups of matt finish type and size as approved by Egineer-in-charge

PCC 1:2:4 type B-1 (using 20m graded crushed stone aggregate) as in roof padding, roof kerbs rounded or chamfered on edges complete all as specified and directed.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 surfaces finished even and smooth without using extra cement mixed with @ 3% of waterproofing complete all as specified. (Note : WPC measured and paid saparately)

Supply only integral water proofing compound (ISI Marked) complete all as specified & directed.

3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3.6kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gm/sqm) laid over a coat of bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS, over primer coat bonding material of blown bitumen 85/25 grade heated to working temperature of 180° C applied @1.2Kg/Sqm. The membrane shall be laid using butane torch and sealing all joints etc after preparing the surface as per standard practice and as per manufacturer instructions including dismantling of existing felt /treatment, complete all as specified & directed.

factory made cement concrete tiles 250mm x 250mm x 25mm thick (with grey cement and no pigments), set, jointed and pointed in neat cement slurry with grey cement with pigment to match the colour of tiles, laid over and including 20mm thick screed bed in cement mortar 1:4, mixed with water proofing polymeric compound wth 3mm thick / wide joints filled ith FEVIMAE of Dr Fixit or pidilite industries of tiles glue of STP Ltdcomplete all as specified and directed.

Reinforced cement concrete type A-1, 1:1½:3 (nominal mix, using 12.5mm graded crushed stone aggregate) as in slabs supported on walls, beams, balconies, roofs, canopies shelves and the like complete all as specified and directed (reinforcement shall be measured and paid for separately).

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick screed or bedding layer in CM 1:6, complete all as specified and directed.

25mm thick Plain cement concrete 1:2:4 type B-0 using 12.5mm graded aggregate as in floor even and rough to receive the top finshes complete all as specified & directed.

Glazed coloured ceramic tiles in vertical surface 450mm x 300mm x 7mm thick thick , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

16 to 18mm thick granite stone slabs(one piece), machine cut (of any type) work (table rubbed and polished) width and length as ordered, best quality machine cut and granite polished to be fixed on kitchen platform, window-cills, counter slab etc jointed with gray cement slurry and pointed in white cement mixed with marble dust (1:2) with admixture of pigment to match the shade of slab, screed bed 15mm thick in cement mortar 1:6 and rounding off/bull nosing exposed edges complete all as specified and directed.

All as per serial item No 25 hereinbefore but on skirting / vertical surfaces laid over and including 10mm rendering in cement mortar 1:3, compelte all as specified and directed

100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

Concrete interlocking pre polished paver block, with grey cement and pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning, complete all as specified and directed

Coloured non skid porcelain tiles exterior grade 300x300x15mm thick heavy duty (Endura from Johnson or equivalent) as in floor, set and jointed in neat slurry and pointed in coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar 1:6, complete all as specified and directed

75mm thick plain cement concrete type C-1 1:3:6(Using 20mm graded crushed stone aggregates) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

Brick work with sub class ‘B’ bricks of old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

15mm thick rendering in cement mortar 1:4 on brick walls or concrete surface and finished fair and even without using extra cement complete all as specified & directed.

15mm thick rendering in cement mortar 1:6 on brick walls or concrete surface and finished fair and even without using extra cement complete all as specified & directed.

10mm thick rendering in Cement and Sand mortar 1:3 on ceiling, chajja surfaces (concrete surfaces) finished even and smooth without using extra cement, complete all as specified and directed.

Two or more coats on new plastered surfaces of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 liter/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. Note Necessary scaffolding, safety precaution and other arrangement complete all as specified and directed.

Two or more coats on old plastered surfaces of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 liter/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. Note Necessary scaffolding, safety precaution and other arrangement complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper in approved tint over a coat of primer, all as specified and directed.

Preparation of old plastered wall surfaces and applying two coats of oil bound distemper in approved tint over a coat of primer, all as specified and directed.

Applying wall care putty of 1.5mm thick in two layers including rubbing the surface in each layers of wall putty with sand papers etc., (preparatory to OBD/ plastic emulsion/ interior/ exterior emulsion paint as directed) complete all as specified and directed

Three coats of white wash on plastered or unplastered wall surfaces including preparation of new surfaces complete all as specified and directed

One coat of white wash on ceiling surfaces including preparation of old plastered surfaces complete all as specified and directed.

Preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of new steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) complete all as specified & directed by Engineer-in-charge.

Material and labour preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Taking down chowkhats or frame n. exc. 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frame exc. 1.5 sqm and n exc 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm complete all as specified & directed.

Pressed steel frames 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including fill of PCC 1:3:6 complete all as specified and directed.

Pressed steel frames 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including fill of PCC 1:3:6 complete all as specified and directed.

35mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides all as specified & directed by Engineer-in-charge.

Glazed and gauged skelton shutter (Factory made) 35mm thick of second class hard wood open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.20 (a) including Kiln seasoned and chemically pressure treated, complete all as specified & directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0, fixed as in repair all as specified and directed.

Providing and fixing factory made uPVG white colour sliding window Three track area not excedding 2 sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed.

Providing and fixing factory made uPVG white colour sliding window Three track area excedding 2 sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed.

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

5mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

5mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

5mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square exc 0.5 Sqm in each panesas in repair complete all as specified and directed.

Butt hinges 100mm size, of extruded aluminum alloy with galvanised mild steel hinge pin, anodised, type C-21, complete all as specified and directed.

200 mm size aluminium, barrel tower bolt of extruded section complete all as specified and directed.

150 mm size aluminium, barrel tower bolt of extruded section complete all as specified and directed.

150 mm aluminium handles cast type complete all as specified and directed.

Aluminum alloy, anodized, sliding door bolt (ISI Marked), 300mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, complete all as specified and directed.

300mm long mild steel helical door springs including roller and roller plate, fixed as in repair complete all as specified and directed.

140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, fixed as in repair complete all as specified & directed

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Supply and fix 6mm thick aluminium composite panel sheet (ACP) colour as approved by Engr In Charge all as specified and directed.

Mortice lock, verticle type, mild steel, 4 levers, size 100mm, brass body, complete all as specified and directed

Door closer hydraulically regulated aluminium extruded section, designation No 3, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kilogram , fixed in repairs, complete all as specified and directed.

25mm dia stainless steel curtain rod including fixing fancy types brackets, stops, rollers etc., as in repairs complete all as specified and directed.

Factory made 18mm thick solid WPC (Wood Polymer Composite) board of density 650 Kg /cum of one side prelaminated / rigidlam with any colour and other side balancing laminate as in cup board/ kitchen cabinet shutter/ drawer, front shuters, fixed with screws, solvent / adhesive complete all as specified and directed.

Dismantling of wall and ceiling board (fibre, pulp insulation etc) any thickness including cover fillet complete all as specified and directed

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) With Semi preforated 12mm thick micro tegular edged GRG false ceiling tiles, false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2% humidity resistance of 99% NRO .05 to 0.75 as per IS 8225:1987, Non-combustible as per BS 476 (part4)- 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides ) comprising of main- T runners of size 15 x32 mm of length 3000mm, cross-T of sixe 15 x 32 mm of length 1200mm and secondary intermediate Cross-T of size 15 x 32mm of length 600mm to from grid module of size 600 x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per direction of the Engineer-in-Charge.

PVC sheet fillet 35mm wide, 5mm thick for wall paneling, inlusive fixing on to wall to make PVC frame complete all as specified and directed.

20mm wide and 1mm thick PVC edge bedding of PVC pasted on edges with suitable adhesive complete all as specified and directed.

Magnetic catcher cum silence CP and fixed with standard steel screws, as in repair complete all as specified and directed

Hydraulic hinges for modular kitchen as in repair complete all as specified and directed.

Stainelss steel handles 16mm x 20mm for modular kitchen as in repair compelte all as specified and directed.

PVC (SWR) rain water pipe, 150mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm, fixed as in repair including nuts bolts etc, complete all as specified and directed.

150mm bore PVC (SWR) bends any radius complete all as specified and directed

100mm bore cast iron soil waste and vent pipes in any length with or without ears with cement joints, fixed to wallls, fixed as in repair complete all as specified and directed.

All as per serial item No 87 herein before but 75mm bore of pipes -ditto-

Cast iron bends (any radius), diminishing pieces or tapers (largrer bore measured), suitable for 75 mm bore spun pipes, ISI marked, fixed as in repairs complete all as specified.

Cast iron bends (any radius), diminishing pieces or tapers (largrer bore measured), suitable for 100mm bore spun pipes, ISI marked, fixed as in repairs complete all as specified.

100mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and direted.

75mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and direted.

100mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1, (1:2:4),complete all as specified & directed

75mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1, (1:2:4),complete all as specified & directed

Sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes: including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified & directed by Engineer-in-charge.

Vitreous China half stall urinal, fixed against wall in cement mortar (1:2), securing urinal with and including 60mm long brass screws, pointing around urinal back in cement, including CP waste coupling, 32mm PVC waste pipe, fixed as in repair complete all as specified and directed.

Brass CP Urinal spreader suitable for 15mm bore pipe, fixed as in repair, complete all as specified & directed.

Counter top wash basin, of Size 560x 470x190mm, oval shape, white colour, including waste pipe, CP angle valve, CP waste coupling etc fixed in position, fixed as in repair complete all as specified and directed.

Vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest including 'P' or 'S' trap (excluding flushing cistern and flush pipe) and making good to the floor fixed as in repair complete all as specified & directed by Engineer-in-charge.

Vitreous china, wash down water closet pan, superior white, Pedestal pattern WC with ‘P’ or ‘S’ trap, seat cover (excluding, flushing cistern and flush pipe), fixed as in repair complete all as specified and directed.

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend, set with concrete and making good to floor, fixed as in repair complete all as specified & directed.

Brass chromium plated bottle traps 40mm bore for wash basins, minimum water seal 25mm, with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

Bib taps brass, fancy type, long body with wall flange, standard chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, compl complete all as specified and directed.

Single lever extended basin mixer, without Popup waste and 450mm Long Braided Hoses, cast copper alloy, cast copper alloy chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

PVC connection 15mm size with PTMT nuts of length 450mm long as in repairs complete all as specified and directed.

Cast copper alloy, chromium plated towel rail 600mm long, fixed as in repair, complete all as specified and directed.

Brass chromium plated towel ring, fixed with brass screws complete all as specified and directed

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Toilet paper holder, cast copper alloy, chromium plated, fixed in position, fixed as in repair complete all as specified and directed.

Health faucet brass chromium plated (health faucet with 01 m pipe & wall hook) for 15mm bore with fittings, fixed as in repair complete all as specified and directed.

25mm dia GI tubing medium grade with all fittings , fixed into walls, ceiling or laid under floors and taking down existing tubing, complete all as specified and directed.

20mm dia GI tubing medium grade with all fittings , fixed into walls, ceiling or laid under floors and taking down existing tubing, complete all as specified and directed.

15mm dia GI tubing medium grade with all fittings , fixed into walls, ceiling or laid under floors and taking down existing tubing, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc and cutting chases for concealed water tubing & making good, cutting not exc 10 cm girth, in brick walls complete all as specified and directed.

20mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repairs,complete all as specified and directed.

25mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repairs,complete all as specified and directed.

1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered hoisted and fixed in position, including PTMT tank nipple, PTMT float valve of 20 mm bore etc, fixed as in repairs complete all as specified and directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

Taking down carefully aluminum/copper point wiring on & including hard wood battens, surface conduit and board/blocks etc or through conduits for light , socket or power point ,fan point complete incl fitting such as switches ,sockets, ceiling rose , holder socket, light fitting, regulators and making good disturbed surfaces of wall, floor , ceiling etc and removing materials (other than those for which credit has been given by the contractor) to the MES stores yard for keeping in safe custody complete

Point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new modular sunken boxes 1.2mm thickness covered with provision of 3mm thick plastic laminated sheet, comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original finishes surface and nothing extra shall be paid on this account.

All as per serial item 121 herein before but for socket outlet 3 pin 6Amps on same board complete all as specified and directed

All as per serial item 121 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 121 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed.

Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose two module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed.

Modular switch type stepped fan regulator, single pole, 230 volt two module complete all as specified and directed.

Modular switch type bell push, single pole, 230 volt one module,(ISI marked) complete all as specified and directed.

Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

Electric Bell, ding dong, AC, 230 volts, single pole all as specified and directed by Engineer-in-charge.

Disconnecting the power supply and taking down carefully by unscrewing from boards fittings and fixtures such as DBs, Junction Box, Panels of any size complete with all MCCB's ,MCB's etc and removing from site, Complete all as specified and directed .

MCCB, 125 Amps, four pole, 3 phase , 16KA, 415 volt with adjustable thermal and maganetic release, with proper thimble complete all as specified and directed

Vertical TPN distribution board double door flush mounting with provisions for MCCBs incomer upto 125 Amps & outgoing 4 way having IP 43 protection Complete all as specified and directed .

MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 08 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB DB, IP 43 protection, powder coated single door with locking arrangement suitable for surface and flush mounting, 02 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB, SPN, 240 volt, 32 Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB, SP, 240 volt, 40 to 63Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB ,SP, 240 volt, 6 Amps to 32 Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size fixed as in repair complete all as specified and directed.

Slim LED lights fitting, 4 feet, 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed.

Slim LED lights fitting, 2 feet, 1x 10W, inverter rechargeable, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed.

Taking down carefully old copper or aluminium sub main wiring of any Nos of wiring and size with earth wire on wooden batten/ surface conduit/ casing- capping complete with its all accessories and making good disturbed surfaces of wall , floors etc complete all as specified and directed.

Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 4 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 4 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 4 sqmm and one single core earth cable of 4 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

Supply and fixing sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 10 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 10 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 32/40mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 10 sqmm and one single core earth cable of 10 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth Complete all as specified and directed .

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver,including lamp bracket upto 1.5metre length as per suitable for fitting including clamp with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection, fixed as in repair complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complete including dismantling of old earthing, all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) unit rate including protection pipe and GI wire 4.00mm dia from top to earth plate upto 7.5 meter

M/S Gupta and Sons (BID ID -3211345)