SPL REPAIR OF OR LINE BLDG NO T 212 ALONG WITH PROVN OF FALSE CEILING, NEW ELECTRIC FITMENTS AND FLOOR TILING AT JADC IN SUKNA MIL STN AND CERTAIN OTHER SANCTIONED WORKS IN SUKNA MIL STN UNDER GE SUKNA.

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Soft/ Loose soil.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil / loose soil complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in Soft/ Loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m & making good surface complete all as specified and directed.

Surface dressing not exc. 15 cm deep as in soft / loose soil complete all as specified and directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Removing Excavated soils not exc 50 M and depositing where directed at a level not exc1.5 M above the starting point complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M&L PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in gap between roof sheet and brick wall, thickness of concrete bed exc. 5 cm and not exc. 10 cm thick & width not exc. width of one brick thick wall including necessary scaffolding and formwork height upto 7m complete all as specified and directed.

M&L for Plain Cement Concrete Type C2 1:3:6 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, sub base under floor, filling and mass concrete complete all as specified and directed.

M&L for Reinforced Cement Concrete Type B-1 1:2:4 (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Material and labour for burnt modular brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar ( 1:6) all as specified and directed.

M&L for fly ash brickwork with old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar ( 1:6) having compressive strenght not less than 75 kg/Sq cm complete all as specified and directed.

M&L for rough finished flat form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

M& L in repairs for second class hard wood clean sawn in scantlings, truss with glue pinned at joints and fixed in repairs to replace old and decayed timber ( including piecing, scarfing etc., of old and new timbers if required) complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkhats complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with MDF and plywood face panels, commercial type on both side and covered on both sides complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete as all specified and as directed.

S & F of 200 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S & F of 150 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and directed.

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges with steel screws complete all as specified and directed.

S & F 100 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type B-21 complete all as specified and directed.

S & F 75 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C 21 complete all as specified and directed.

S&F Mild steel helical door spring 150 mm size including roller and roller plate fixed to wooden or steel frames with welding etc complete all as specified and directed.

S&F 150 mm long Aluminium handles fabricated type, anodised and fixed complete all as specified and directed.

S&F 100 mm long Aluminium handles fabricated type, anodised and fixed complete all as specified and directed.

S&F mortice locks suitable for aluminium door of 100 mm size 4- lever vertical type brass as per existing or sample complete all as specified and directed.

Supply & fix as in repair curtain harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. with two Nos. of socket ,end caps and brakets (decorative type) complete for doors/window opening complete all as specified and directed

S&F in repair towel rail 20 mm dia & 600 mm long of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S & F in repairs Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and directed.

S & F in repair Aluminium body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 oto 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or stainless steel wire staples complete all as specified and directed.

S&F framed work such as in gate, rollers, cleats, base plates , plain or chequered and rail etc, with and similar work conforming to Fe 290. Gde -E-165 for framed and hung as gates including hold fast pintle hinges stops hand made sliding bolts and ornamental and intricate design, etc complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings,framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Mild steel screw bolts diameter of neck 16 to 20 mm (machine made) with hexoganal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut, exc. 22.5 cm but not exc. 30 cm long complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S & F Joint, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Structural steel work of angle, channel etc., confirming to Fe 410 -W (Gde- E- 250) Quality-A complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S & F of rolled mild steel sections as in framing of cladding, glazing, door or gates and the like fixed with angle cleats and connecting plates etc. confirming to Fe – 410 – W(Gde E - 250) quality 'A' complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc.and including P.C.C. (1:3:6) for filling in frame and fixing of hold fast, complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc.and including P.C.C. (1:3:6) for filling in frame and fixing of hold fast, complete all as specified and directed.

M&L powder coated Aluminium anodised door, window, Cup board and ventilator shutter and frame any type (Sliding or openable ) with frame and other similar work, fabricated aluminium mesh etc. aluminium heavy section favricated incl all necessary roller wheels, cleats, handle, locking arrangement and arrangement to fix wire mesh with aluminium channel beading and stainless steel screw incl cost of rubber gasket ,beading roller wheel etc. ,complete all as specified and directed. Note: (a) The weight of rubber gasket beading, roller wheels, etc will not be measured with the weight of aluminium shutters as only aluminium items shall be measure. (b) Wire mesh shall be measured and paid separately. (c) Aluminium hinges shall be included in the unit rate

S&F Powder coated anodised aluminium window (two/three track) sliding type without sash bar and ventilator shutters ((louver type),aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading,rollers, screws etc complete all as specified and directed.

S&F (E-board designer/ decorative) 4 mm thick non asbestos fibre cement building boards (designer pattern) fixed or laid / inserted to aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm with and including anodised aluminium snap grid frame size 605x605 mm work for false ceiling Hangers with 6 mm dia. G.I. (length as required) adjusting level fixed to roof slabs/truss by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

Material & Labour in repairs 19/20 mm thick Block boards, grade 2 quality, interior grade, laminated sheet with decorative face, veneer on one face, commercial type fixed with screws to timber frame work & bedding complete all as specified and directed.

M&L 75 mm thick PCC 1: 3:6 type C2 using 20mm graded aggregate finishing even and smooth without using extra cement as in plinth protections/path and laid fair in alternate bays & construction joints to be given at every 3m interval and corners of buildings and filled with bituminous mastic or equivalent filler complete all as specifed and as directed.

M&L for 100 mm thick cement concrete, type B2, 1:2:4 (using 40 mm graded stone aggregate) as in flooring and finishing the surface even and fair complete all as specified and directed.

M&L for providing 100 mm thick cement concrete 1:3:6 type C1 (using 20 mm graded crushed stone)as in hardstanding / path laid in alternate bays ( n. exc. 4 Sqm each) and finished even and smooth without using extra cement complete all as specified and directed

M&L for 75 mm thick cement concrete, type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring finished rough to receive finishes complete all as specified and directed.

S&F 1.5 mm thick and 38 mm wide Aluminium dividing strips as in floors inserted in position, conform to design complete all as specified and directed.

M & L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry in floors and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid & enosing jointed over and including 20mm cement screed in CM 1:6 complete all as specified and directed.

M&L for Granite (of any type) tiles in skirting/dado 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 12mm thick rendering in CM 1:4 including dismentling existing tiles complete all as specified and as directed by Engineer-in-Charge.

M&L premium quality coloured vitrified ceremic tiles 8-10 mm thick (square/rectangular) polished, area of each tiles not exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over including screed bed or bedding layer of mortar 20 mm thick for laying floor tiles in cement mortar 1:6 finished even and rough complete all as specified and directed.

M&L premium quality coloured vitrified ceremic tiles 8- 10 mm thick (square/rectangular) polished, area of each tiles not exc 0.36 Sqm in vertical surface in skirting etc set and jointed :in neat cemetn slurry and pointed in white or coloured cement to match including 10 mm thick backing coat in CM 1:3 complete all as specified and as directed complete all as specified and directed.

M&L coloured glazed ceramic tiles 350x250x7 / 450 x 300 x 7 mm thick as in dado / skirting and vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:3 including roughening of surface complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 20 mm thick in CM 1:6 acomplete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 20 mm thick in CM 1:6 acomplete all as specified and directed.

M&L 60 mm thick machine pressed precast concrete interlocking coloured paver block of any shape and size confirming to IS 15658-2006, M-35 grade, set with grey cement and pigment, laid over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and fair without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

S&F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and as directed.

M&L preparation of newely plaster surfaces and appplying two coats of weather coat acrylic exterior emulsion paint over a coat of primer of damp shield to new plastered walls as per manufacturer and apllied by approved applicator complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of weather coat acrylic exterior emulsion paint over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L for preparing old surfaces of walls (old decorated plastered or unplastered) and applying one coat of white wash complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of cement base paint complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L preparation of old plastered or un plastered surface of celing and applying one coats of white wash complete all as specified and directed.

M & L for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

S&F 4.8mm thick tinted/ heat absorbing glass including tinted/dark film exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber and aluminium beading complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

M&L for preparation of new wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of Synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, in walls / ceiling or in floors etc. complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, in walls / ceiling or in floors etc. complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed.

S & F in repair of 15 mm bore bib tap long body, chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make:- Jaquar Essco, Cat No. - SQT-511KN or equivalent in Hindware / Cera/ Prayag

S&F in repairs pillar tap 15 mm bore,fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. Make:- Jaquar (Essco), Cat No. - SQT-507KN or equivalent in Hindware / Cera / Prayag

S & F in repair 15mm bore stop valve/ stop cock, fancy type,chromium plated, cast copper alloy, concealed type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for 15 mm bore dia iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for 20 mm bore dia iron pipe or brass ferrule and fixed complete all as specified and directed.

S & F in repairs Grating doom 100 mm dia with waste hole of stainless steel CP complete all as specified and directed.

S&F in repair stainless steel towel rings chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 600 mm complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S & F in repairs sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers, waste coupling and waste pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 495 mm x 420 bowl size 410mm x 330mm x 160mm fixed complete all as specified and directed.

S&F in repairs vitreous china squatting pan, "Orissa pattern" white, size 580 x 440 mm with integral foot rest, 'P' or 'S' trap and including connection to trap and to flushing pipe, CI anti -syphonage pipe complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size 580 x 450 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

Supply and fix, as in repair, brass CP 40/32mm dia waste coupling with inlet and out let screwed for pipe or connections including packing, union and cap etc complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets & 32 mm dia PVC flush bend pipe complete all as specified and directed.

S & F in repair for Soap dish, brass CP, fixed to plug with chromium plated brass screws complete all as specified and directed.

S&F Stack clamps including bolts and nuts and securing ends of stays to wall or roof for 100/75mm bore complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below and above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern in roof and wall covering omplete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

S&F factory made 28mm thick soild PVC flush door shutter made from co-exturded 3 layer rigid PVC foam sheet (single extruded) water proofing and termite proof and fire retardent having density 600 kg/cum (minimum) outer layer 0.8 to 1mm thick of rigid PVC with density 1400kg/cum complete all as specified and as directed.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch and including cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed.

All as per Sl. item No. 132.00 above but for one 5 / 6 Amps socket outlet point on same board.

All as per item No.132.00 above but for 3 pin 5 amps socket outlet independent(multiple) controlled by one switch complete all as specified and directed.

All as per item No. 132.00 above but 2.5 sqmm copper conductor for 3 pin 15 amps socket outlet independent(multiple) controlled by one switch with one No earth continuity copper conductor of size 2.5sqmm complete all as specified and directed.

All as per Sl. item No. 132.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including PVC casing caping (double lock pattern) and accessories on wall / ceiling surfaces etc. with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc including all other fixing accessories for one light / fan / exhaust fan point controlled by one 5 / 6 Amps switch complete all as specified and directed.

All as per Sl. item No. 137.00 above but for one 5 / 6 Amps socket outlet point on same board.

All as per Sl. item No. 137.00 above but for one 5 / 6 Amps socket outlet point on independent board.

M & L concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L concealed sub main wiring with 2 runs of 4.00 sqmm main wire along with 1 run of 4.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

Taking down copper / aluminium concealed sub main wiring complete with all fixture and fittings including cutting chasing as required and making good the disturbed surfaces including finishes to match with adjacent surfaces of walls, floors, etc. complete all as specified and as directed.

M & L concealed sub main wiring with 2 runs of 6 sqmm main wire along with 1 run of 6 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F switch piano flush type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F socket outlet 5 pin 5 / 6 Amps, flush type, 240 volts complete all as specified and directed.

S&F switch piano, single pole, two way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch socket combination 3 pin 15 Amp, flush type universal complete all as specified and directed.

S&F MCB SP,10KA, 230V, C-curve, 6-32 amps complete all as specified and directed.

S&F MCB SPN 40 to 63 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S & F in repair LED Bulk Head fitting 15 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF ≥0.95, total System Lumens not less than 1100 lm, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed.

Supply & laying LT XLPE insulated, armoured heavy duty electric cable with alumimium conductor, 1100 volts grade, cross sectional area 10 sqmm x 2 Core, laid in trenches / duct / on pole complete all as specified and directed.

Sand cushioning in trenches for cushioning of LT underground cable including spreading, levelling, well ramming in layers not exceeding 25cm in depth, complete all as specified and directed. Note : Punned thickness of 18 cm shall only be measured and paid.

Supply and fix sub class 'B' bricks of standard size for cable protection laid flat acrossthe cable in trenches complete all as specified and directed.

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

S&F stepped type electronic fan regulator two module, with 5 step, AC 50 Hz 240 Volts grade complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and as directed.

S&F MCB DB, SPN 8 way, IP-43, IK 09, double door type with metal door, with 100A copper neutral and earth bus bar for fixing MCB, fixing flush to wall & making good the disturbed surfaces complete all as specified and as directed.

S&F in repairs LED battery backup inverter bulb of Lamp wattage: - 9 to 12 Watts, Battery: - Not less than 2200mAh or not less than 4 hrs backup,Efficeacy: - Not less than 110 Lm/Watt complete all as specified and directed.

S & F in repair Surface and wall mounted LED batten 20 watt 4ft long with Aluminum extruded housing , high quality polycarbonate diffuser & integrated Electronic Driver with IP20, PF 0.95, Efficiency not less than 110 lm/W color temp 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and directed.

S&F LED batten light fitting 1 x 10 watt inverter (backup) type, 230 Volts, suitable for surface mounting, lithium ion battery with minimum 4 hrs backup time, extruded polycarbonate housing & extruded polycarbonate diffuser, lumen efficacy 110 Lm / watt (minimum), colour temperature 650 0K (minimum), CRI 80 (minimum), IP-20 (minimum), PF 0.90 (minimum), in-built surge protection 3.5 KV (minimum) inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting & taking down complete all as specified and directed.

S & F in repair LED Bulk Head fitting 10 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF ≥0.95, total System Lumens not less than 1100 lm, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed.

S & F in repair LED Bldg Security Light 30 watt made up of pressure die cast aluminiun housing with highly efficient LEDs and PC cover with integrated lens with IP66, IK07, System Lumen Efficasy ≥120 Lm/W, having unique air vent technology which keeps temperature low, 5 kV Surge Voltage Protection,Operating Voltage range 140 V - 270 V and bracket suitable for street light made out of GI pipe light grade of 25 mm bore & 0.75 mtr length (minimum), bend to shape including 2 pairs of MS flat iron clamps made out of 40 x 5 mm MS flat, nuts, bolts & washers etc, & painting the bracket with two coat of aluminium paint over a coat of red oxide primer complete all as specified and as directed.

S&F VTPN DB,MCCB incomer,4 ways double door,Metal door ,IP-43 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 250+12 complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unsv ones including MCCB's etc complete all as specified and as directed.

S&F MCCB 4P 125 Amps 415V ,50 Hz ,breaking capacity 25 KA complete all as specified and directed.

S & F Switch piano 5 Amps single pole bell push incluing taking down old unsv ones complete all as specified and as directed.

S &F Bell buzzer, Ding Dong AC. 230 volts, single pole completed as directed.

S & F Socket outlet 5 Amps 3 pin flush type incluing taking down old unsv ones complete all as specified and as directed.

Supply and fix in repair of energy saving BLDC ceiling fan complete with all connected accessories as specified below: - Input Power: - 26 watts with full speed and reduced power consumption with reduced speed technology. Voltage: - 90-300 V AC, 50Hz, single Phase. RPM: - 340 to 375 rpm Blades: - Decorated Sweep: - 1200 mm. Air delivery: - Not less than 210 CFM Colour: - Glow white/Toast Brown/Gloss Black/or others as approved by Engr-in-Charge Speed/power control: -Without Remote through existing regulator. Star rating: - BEE 5 Star Rating Warranty: - As specified by the manufacturer, contractor shall produce original warranty and test certificate from the manufacturer.

M &L of Earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected using galvanised iron earth lead wire 4 Sq mm as earthing electrode by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe (medium grade) and other end connected to earthing test point as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C both ways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth up to a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be made again by the contractor at no additional cost and including dimantling complete all as specified and directed.

S&F earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4 mm dia galvanised iron or steel wire complete all as specified and directed.

DAS AND GHOSH CONSTRUCTION

SHANTI UDYOG

R N SAH N CO

A K ENTERPRISES

ELECTRO WIR WAY

M/S RANEN PAL

VICKY ENTERPRISES