MISC MAINTS TO CERTAIN OTM ACCN AT BD BARI MIL STN UNDER GE KALUCHAK

Amount

Taking down chowkats or frames with shutters (without taking off shutter from the frames) not exceeding 1.50 Sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exceeding 1.5 sqm & not exceeding 4 sqm each complete all as specified and directed

M&L for pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, keys , hinges lock, lock strike plate etc.made out of 1.25mm thick MS sheet including one shop coat of red oxide zinc chrome primer etc complete all as specified and directed .

M&L for pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, keys , hinges lock, lock strike plate etc.made out of 1.25mm thick MS sheet including one shop coat of red oxide zinc chrome primer etc complete all as specified and directed .

M&L for PCC 1:3:6 type C - 1 (using 20 mm graded crushed stone aggregate) as in back filling of chowkats and bed blocks for hold fasts etc complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with partical board complete all as specified and directed.

M&L for 2nd Class hard wood 35mm thick factory made glazed and skelton shutters open rebated and prepared to receive glass , gauze,etc (without sash bars) edges of framing plain , chamfered or rounded. Fitted with cut and mitred beads for securing wiremesh supplied and fitted to chowkats complete all as specified and directed.

M&L for Mild steel framed work as in doors ( as in chowkats)or gates of angle or other section with guest plates rails, braces rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to Fe-410- W(Gde- E-250) quality- B including shop coat of red oxide including preparation of surface before fixing.

M&L for Solid PVC door/cup board frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening complete all as specified and directed.

M&L for Factory made solid panel PVC door/cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suippling and fixing in the frame at site as per specification in SSR Part-I. complete all as specified and directed.

M&L for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with 2nd class soft wooden beadings or fixed with screws to Iron framed windows all as specified and directed

M&L for Butt Hinges medium weight cold rolled mild steel of size 100 mm complete all as specified and directed

M&L for 150 mm size mild aluminium handles cast type anodised complete all as specified and directed

M&L for 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L for 300 mm size Mild steel stove enamelled helical door spring fixed to Pressed steel frame / chowkhats including necessary welding complete all as specified and directed.

M&L for Steel ventilator with top hung shutter including hinges , steel peg stay including taking down old steel ventilator of any size complete all as specified & directed.

Dismantling boarding any description fixed with screws complete all as specified and directed.

S&F 18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboards , kitchen cabinet etc fixed in repairs complete all as specified and directed.

S&F Continuous (piano) hinges,width of flap when open is 30 mm mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Magnetic catches of 25/30 mm size for cup Board shutter etc complete all as specified and directed.

S&F hasp and stapple, safety typeof Aluminium, anodised, including bolt to hinge type, fixed with screws of 100 mm complete all as specified.

Dismantling of plain or corrugated steel sheeting ,any gauge, thickness including roof covering etc complete all as specified and directed.

Dismantling of plain or corrugated asbestos cement sheeting ,any gauge, thickness including roof covering etc complete all as specified and directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified & directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in as in ridges, hips, valley gutters, drip and straight flashings, fixed with self tapping screws, complete all as specified & directed.

Demolition of brick work or stone masonary built in cement mortar including all quoins , arches, pillar etc but excluding ashlars facing dressed stone work and pre-cast concrete article complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks ,straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6 complete , but except bricks , i.e using serviceable bricks obtained from demolition complete all as specified and directed

Dismantling floor, hearth or wall tiling , terrazzo topping on walls including cement mortar , bedding (including backing) removing serviceable tiles and rubbish off the premises complete all as specified and directed.

M&L for Non - skid ceramic coloured jointless tile 400mm x 400mm x 7mm thick as in floors laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles complete, all as specified and directed.

M&L for Non - skid ceramic coloured jointless tiles 400mm x 400mm x 7 mm thick on vertical surfaces such as skirting /dado etc bedded & jointed in neat cement slurry over and including 10 mm thick backing coat of cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles complete, all as specified and directed.

M&L for Glazed ceramic coloured tiles of size300x450x7 mm thick as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

M&L for sunken treatment with glass fiber reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent) complete all as following :- Base Coat : Berger HS Latex plus (or equivalent) consumption base coat : 0.3 kg/m2 Reinforcement : Glass fiber Second and Third coat : Latex sheild 2K (or equivalent) Consumption top coat : 3 kg/m2 System reqquirements : density : 2.00 kg/ltr; Compressive strength: 0.5N/mm2 Wall penetration through the RCC slab must be sealed using Berger HS Repair (or equivalent). Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus (or equivalent) modified mortar with a bonding coat of Berger HS Latexplus (or equivalent) modified cement slurry upto sft. All depressions, unevenness, surface honeycombng shal be repaired using Berger HS Latex plus (or equivalent) modifiled polymer mortar with a bonding coat of Berger HS latex plus (or equivalent) modified cement slurry. Including cleaning of RCC surface to remove dust, loose paricles, etc with compressed air or any other suitable technique depending on site conditions, grinding aby sharp edges, etc. Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'EF' on page no. 91 of tender documents as per Sch 'A' Note No 19 Page No 17).

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 with water proofing compound tobe finished even and smooth without using extra cement complete all as specified and as directed (WPC to be measured and paid separately)

Supply only Integral water proofing compound liquid complete all as specified and as directed.

S&F 20mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in as spout pipes to pour out rsidual water out from the treated area.

M&L for hard core, of broken bricks broken to gauge n exc 63mm for laying sub base of thickness 150mm complete all as specified and directed.

M&L Cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate) in foundations, filling and mass concrete in sub base complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B1 with 20mm graded aggregate for laying floor tiles complete all as specified and as directed.

M&L for non skid coloured Ceramic tiles 8 to 10 mm thick in light shade (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 sqm, in floors/Skirting etc. set, jointed and pointed with Berger HS tile adhesive anti slip white @1.2kg/sqm thickness upto 8 to 10mm (or equivalent) and epoxy material for sealing of tile joints with Berger HS Epoxy tile grout(or equivalent) to the floor of toilets and bathroom complete all as specified and as directed.

Demolition of cement concrete in and paving (un reinforced) exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified & directed.

Demolition of cement concrete in and paving (un reinforced) n exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified & directed.

M&L of Machine cut kota stone flooring 18-20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) (Each stone not less than 55 cms x 55 cms) over 15mm thick screed bed in CM ( 1:4) as in floor finished rough including applying a coat of cement slurry @ 03 Kg/Sqm of surface complete all as specified and as directed.

M&L of Machine cut kota stone 18-20mm thick in skirting, dado ,riser and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) over 15 mm thick rendering in CM ( 1:4) including taking out of existing dado complete all as specified and as directed.

M&L for Vitrified coloured tiles, jointless , light shade of size 600mm x 600mm x 9 to 10 mm thick, as in floors etc bedded & jointed in neat cement slurry over and including 15 mm thick screed bed in cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles, complete all as specified and directed.

M&L for Vitrified coloured tiles,joint less , light shade 600mm x 600mm x 9 to 10mm thick, on vertical surfaces such as skirting / dado etc bedded & jointed in neat cement slurry over and including 10mm thick backing coat of cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles,complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 using (40mm graded crushed stone aggregate ) as in sub base of floor complete all as specified and directed.

M&L for Precast designer coloured heavy duty full body( Durastone) paving tiles (factory made) of size 300mmx300mm x 10mm, top layer glazed made in any type of cement and pigment, in required patterns as approved by GE in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:4, complete all as specified & directed.

M&L for capilary rise treatment of walls as following :- Base coat: Berger HS Latex plus (or equivalent) Consumption base coat: 0.3 kg/m2 Second and Third coat: Latex sheild 2K (or equivalent) Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr Compressive strength: 0.5 N/mm2 Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'AB' on page no. 83 of tender documents as per Sch 'A' Note No 19 Page No 17).

Taking down cement plaster on bricks or stone wall / ceiling decayed surfaces of concrete , roof projections or chajjas etc upto triple storey including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 15mm thick fair faces of brick / concrete surfaces in cement mortar 1:4 finished even and smooth with out using extra cement complete all as specified and directed.(with WPC wherever necessary)

M&L for Rendering 10mm thick on fair face of brick / concrete surfaces in cement mortar 1:6 finished even and smoth without using extra cement complete all as specified and directed.

M&L for Rendering 5 mm thick on concrete surfaces of ceilings in cm 1:3 finished even and smooth without using extra cement complete all as specified and directed

Dismantling water tanks of any description 1000 Ltrs capacity complete all as specified and directed.

Dismantling water tanks of any description 500 Ltrs capacity complete all as specified and directed.

M&L for Rotational moulded polyethlene water storage tanks , triple layered, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 1000 litres including over flow , drain out pipe and all accessories complete all as specified.

M&L for Rotational moulded polyethlene water storage tanks , triple layered, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 500 litres including over flow , drain out pipe and all accessories complete all as specified.

Supply and fixing in repair 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe minimum weight 210 gms complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning, threading for prefixing or removal complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning, threading for prefixing or removal complete all as specified and directed.

M&L for Steel tubing medium grade galvanised of 20mm bore with all fitting and fixed complete to walls and ceiling or laid in floors. Make ISI marked

M&L for Steel tubing medium grade galvanised of 15 mm bore with all fitting and fixed complete to walls and ceiling or laid in floors. Make ISI marked

Refixing old galvanised steel tubing of 20 mm bore and connections in new or old position with all fittings fixed complete to walls , ceiling, or laid in floors etc. Complete all as specified and directed.

Refixing old galvanised steel tubing of 15 mm bore and connections in new or old position with all fittings fixed complete to walls , ceiling, or laid in floors etc. Complete all as specified and directed.

M&L for Stop cock/ angle valve 15 mm cast cooper alloy of screwed down high pressure with crutch or Fancy type , screwed with ends for iron pipe or unions fixed in repairs. Make ISI marked

M&L for Bib taps 15mm dia cast copper alloy fancy type chromium plated, screwed down for iron pipe or for brass ferrule fixed in repair complete all as specified and directed.

M&L for Pillar taps 15 mm dia, cast copper alloy,fancy type with capstan heads, chromium plated, screwed down high pressure with or with out lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe fixed in repairs complete all as spd & directed.

M&L for Fancy type Brass CP wash hand basin mixer for mixing hot & cold water, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions fixed in repairs complete, all as specified.

M&L for Shower rose of C.P. swival joint of size 125mm for fixing 15mm pipe including fixing to steel pipe or union fixed in repairs all as specified and directed.

M&L for PVC connections 15mm dia & 600mm long with PTMT nuts all as spd & directed

M&L for PVC connections 15mm dia & 450 mm long with PTMT nuts all as spd & directed

M&L for Sheet glass shelf assembly consisting of 5,5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long make Jaguar or equivalent complete all as specified and as directed.

M&L for Vitreous china wash down water closet (pedestal pattern) coloured complete, including connection to drain pipe and to flushing pipe antisyphonage pipe etc, including seat cover fixed in repair, complete all as specified and as directed.

S & F in repairs water closet vitreous china squatting pan ‘Orrisa’ pattern size 580 X 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, anti-syphonic pipe etc. with and including setting the trap and pan in lime concrete bedding (one lime, two sand or surkhi and 5 aggregate) minimum 150 mm thick alround and finished just below level of rim of pan to receive the floor finishes complete including making good floor complete all as specified and directed.

S& F in repair Low level flushing cistern PVC valveles ,syphonic action type flushing cistern white with inlet valve,float and handle including bracket etc as specified.

M&L for Vitreous china wash basin white flat back size 580x450 mm excluding taps waste chain and plug and porcelain stopper but including brackets, fixed in repair, complete all as spd & directed.

M&L for PVC 32mm dia waste pipe with CP coupling, all as spd & directed.

M&L for Tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between Hangs, fixed in repairs complete all as specified and directed.

M&L for PVC (SWR) floor trap , plain with grating including jointing with solvent cement of 75mm outlet dia complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes of 75/100mm bore, fixed with walls and taking out of trenches, if required all as specified and directed.

M&L for PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall including fixing clamps complete all as specified.

M&L for PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

M&L for PVC (SWR) branch piece, (single Y) equal or unequal 110mm bore complete all as specified and directed.

M&L for PVC (SWR) junction single (single T) equal or unequal 110mm bore all as specified and directed

M&L for PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to wall including fixing clamps complete all as specified.

M&L for PVC (SWR) bends any radius 75mm bore complete all as specified and directed.

M&L for PVC (SWR) branch piece, (single Y) equal or unequal 75mm bore all as specified and directed

M&L for PVC (SWR) junction single (single T) equal or unequal 75mm bore all as specified and directed

M&L for PVC(SWR) vent cowl 75 mm bore complete all as specified and directed.

M&L for Preparation of new plaster surfaces of walls/ ceiling and applying two coats of oil emulsion distemper over a coat of chalk whiting all as specified and directed.

M&L for Preparation of new plaster surfaces of walls and applying two coats of weather coat over one coat of primer complete all as specified and directed.

M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed

M&L for Preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed

M&L for Preparation of old distempered surfaces and applying one coat of oil emulsion distemper on walls and ceilings upto tripple storey all as specified and directed.

M&L for Preparation of old painted wooden surface of any description, over 10 cm in width or girth not other wise described, and applying one coat of synthetic enamel paint all as specified and directed.

M&L for Preparation of old painted steel surface of any description, over 10 cm in width or girth not other wise described, and applying one coat of synthetic enamel paint all as specified and directed.

M&L for Complete removal of of exiting treatment from wall and finish the undulated surface by cement putty and applying two coat of weather proofpaint (Apex) after application of one coat of primer complete all as specified and directed

M&L for Anodised aluminium with powder coating of any colour ( Not less than 50 Micron)frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

M&L for Anodised aluminium with powder coating of any colour ( Not less than 50 Micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

M&L for Anodised aluminium with powder coating of any colour ( Not less than 50 Micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

M&L for Aluminium anodised powder coated (minimum thickness 50 micron) designer grill of 5-6 mm dia of mesh size 50x50mm centre to centre with 25 mm flat inclusing aluminium beading , complete all as specified and directed.

M&L for Providing cement concrete type B-0 1:2:4 (using 12.5 mm graded stone aggregate ) in roof padding, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for Home Sheild PU Roofkoat (or equivalent) is a one component liquid, solvent free, cold applied water-proofing membrane that is highly elastic and UV resistant with 10 years warranty. ASTM D 6083-97 a waterproofing and heat reflecting system having following key performace properties : 1. UV resistant, prevent yellowing and weathering 2. Highly elastic upto 350% and crack bridging 3. Excellent adhesion on porous and non-porous substrates 4. Tensile strength > 10 N/mm2 with Geo Textile fleece 5. Soler reflective Index (SRI) more then 109-111 ASTM E 1980-11 System : First coat : Providing and applying primer over the prepared surface with HS PU roofkoat Primer (or equivalent) Coverage :0.2kg/m2 (with 50 % dilution of water) Reinforcement : Geotextile 40 gsm Second coat : Home sheildroofkoat (or equivalent) Consumption : 0.5 kg/m2 Third coat : HS PU roofkoat (or equivalent) Consumption : 0.8 kg/m2 System buildup-1.5kg/sqm with geotextile of 40 gsm For accessible roof, tiles with scred/ adhesive may be fixed thereafter. Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'CD' on page no. 87 of tender documents as per Sch 'A' Note No 19 Page No 17).

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames glazed with putty or fixed with beads all as spd & directed

S&F sheet glass 3mm thick ordinary quality and glazing with oil putty in square n/exc 0.5 Sqm each pane complete all as specified and directed.

S&F in repair Aluminium anodised tubular curtain rail 20mm dia with bracket and dome complete all as specified and directed.

M/s KULDEEP KUMAR CONTRACTOR (BID ID -3499895)

KAMAL CONSTRUCTION (BID ID -3506100)

BALVINDER SINGH AND SONS (BID ID -3498168)

GENESIS INDIA (BID ID -3499906)

M/s Des Raj and Sons (BID ID -3506061)

J P TECHNO (BID ID -3503983)

m/s sushila devi (BID ID -3505422)