CONSTRUCTION OF HOSTEL AT NCRA-TIFR PUNE

In soft rock

In hard rock by chiselling or by using machine such as Poclain with jack hammer etc.

Depth exceeding 1.5 m & up to 3.0m from ground level

Depth exceeding 3.0 m & up to 4.5m from ground level

Depth exceeding 1.5 m & up to 3 m from ground level

Depth exceeding 3.0 m & up to 4.5m from ground level

Depth exceeding 1.5 m & up to 3 m from ground level

Depth exceeding 3.0 m & up to 4.5m from ground level

Cement concrete of specified grades at all locations & depths for the following works using graded stone aggregate of 20mm maximum size including necessary form work, machine mixing, transporting, placing in position consolidation, finishing, curing etc. complete as per specifications, drawings & as directed by the Engineer in charge. Notes: a) Reinforcement provided if any shall be measured & paid under relevant item. b) MS frame works around pedestals etc. if provided shall be measured under relevant item. c) The dimensions of pedestals/ foundations are likely to be varied and rate quoted shall be final without any additional cost to the Department. PCC M-10 grade in bed concrete to foundations, pedestal, encasing etc.

PCC M-15 grade in sub base flooring, foundation in pedestals, cable pits, cable trenches, plinth protection, encasing etc.

Plum Concrete M-15 grade with 40% of approved quality basalt / trap Boulders of 50 mm to 300 mm size.

Reinforced Cement Concrete of grade M-30 in foundation and plinth at all levels and locations conforming to I.S.456-2000 and 13920 latest edition, using 20mm maximum size down graded stone aggregate including machine mixing, conveying, placing in position, mechanical consolidation, finishing, curing etc. all complete as per specifications, drawings and as directed by the Engineer in charge. Notes for Reinforced Cement Concrete works: i) Cement for structural works shall be OPC/PPC ISI marked and duly approved by the Engineer-in-charge. ii) PPC/ blended cement of ISI marked shall only be used for finishing works on prior approval of Engineer-in-charge. iii) All RCC work shall be controlled concrete unless otherwise specified and shall be carried out strictly in accordance with the drawings and specifications. iv) The rates for RCC works shall be exclusive of cost of reinforcement and form work unless otherwise mentioned. v) All coarse aggregate to be of 20mm. maximum size & uniformly graded unless otherwise mentioned. vi) The water tank and other tanks shall be executed strictly as per following criteria without any additional cost. a) The water tank and other tank work shall be executed as per IS 3370 latest editions in addition to other relevant IS code mentioned elsewhere. b) The minimum cement content for water retaining structures tank shall not be less than 330 kg/cum and not more than 400 kg/cum. c) During construction of raft slab of underground tank, lift pit dewatering shall be continuously carried out to avoid development of water pressure. d) Dead load in the form of sand bag shall be placed on the raft slab of underground tank, lift pit, so as to counteract the pore pressure until the walls are constructed and back filling is done. Number of sand bags required and time period of loading etc. shall be at the discretion of the Engineer in Charge. vii) For all RCC items, the rates quoted shall include the following without any extra cost to the Department. a) Spacers to maintain clear cover for reinforcement. b) Fixing at correct level and in proper alignment the inserts, pipe sleeves, pipe bends, hooks, other pipe specials etc. supplied by/ through the dept. c) Making cut-out wherever required including cutting the form works etc. d) Test for Concrete shall be done as per IS 456-2000 and the cost of the same shall be borne by the contractor. For all type of Structural/ RCC elements with all geometrical shape and sizes

Extra for providing RMC (Ready Mixed Concrete) conforming to IS :4926 (latest) in lieu of conventional RCC and PCC items supplied by approved RMC manufacturers for all type of structural elements/ RCC/ PCC elements including transporting, pumping etc. complete as per instruction of the Engineer in charge. Notes: i) The contractor shall obtain prior approval for RMC manufacturer from Engineer in Charge in writing. ii) The rate shall apply for all levels and locations including all type of structure etc. iii) Extra for RMC in lieu of conventional RCC and PCC of any grade mentioned elsewhere shall be measured and paid under this item for substructure works.

Providing, erecting, fixing in position striking/ removing and cleaning steel / timber shuttering & centering for formwork in foundation and plinth at all locations for all geometrical shapes in plain, curved surfaces of structural/ RCC elements including chamfers, splays, keys, wedges, props, rails, bracings, brackets, cutting holes for pipes etc., providing & applying approved form oil on all surfaces of form work coming in contact with concrete including close hacking of all exposed concrete work after removal of form work, where plastering to be done, including all materials, labour etc. all complete as per specifications, drawings and as directed by the Engineer-in-charge. Notes for form work: a) Area of form work in contact with concrete shall only be measured for payment and stop boards for construction joints will not be measured for payment. b) The rate of form work shall include all type of structural/ RCC elements and geometric shapes including circular and any other curved surfaces. c) For double/ multi stage shuttering design calculations and details / drawings for scaffolding shall be submitted by the contractor well in advance. Prior written approval of formwork shall be obtained from Engineer in Charge, before commencement of work. d) Nothing extra shall be entertained for revision in drawings

Reinforcement for RCC work including supplying, delivering, storing of various diameters as required at site of work including loading, unloading, transporting, decoiling, straightening, cutting, bending, placing in position at all locations & levels and binding with 18gauge, soft drawn annealed steel binding wire including carrying out various tests as required etc. all as per specifications, drawings & as directed by the Engineer in charge. Note: The cost of binding wire shall be borne by the contractor and binding wire shall not be measured for payment. Thermo Mechanically Treated bars of grade Fe-500D/550D manufactured by SAIL, TATA STEEL, JSW and RINL only.

Providing and laying autoclaved aerated cement blocks masonry with 115mm/ 150mm/ 230mm thick AAC blocks as per approved manufacturer, using approved block laying polymer modified adhesive mortar in sub structure at all locations, levels & lead with RCC band, all complete as per direction of Engineer in-Charge. (The payment of RCC band and reinforcement shall be made for separately)

Cement plaster using READY MIX Plaster (RMP) of approved manufacturer in single/ double coat over concrete/ masonry surfaces in CM 1:4 of thickness mentioned below at lift pit/ trenches and all locations to correct line, level, plane, plumb etc., finished smooth with neat cement finish, including preparing the surface, scaffolding, curing etc. all complete as per drawings, specifications and as directed by the Engineer in charge. 20 mm thick smooth finish in two coats on concrete surfaces (internal trench/pit) with water proofing agent @ 2% by weight of cement or as per manufacturers specifications.

Supplying, laying, spreading and compacting the Approved Quality Hard murum, including laying in layers of 200 mm thickness and compaction compulsory using vibratory tamper/plate compactor of required capacity, including artificial watering for settle etc. Approved quality hard murum of required depth is used. Only compacted thickness shall be measured for working out quantity for the payment by taking the Area and depth by Level measurements etc. Rate shall include the cost of all Men, materials, machineries & tools, royalty charges, etc. involved to complete the work in all aspects and all complete as directed by the Engineer-In-Charge.

Disposing off the surplus excavated materials beyond initial lead by mechanical transport to the near by dumping pits/ dumping areas within 3 km inside the site premises/Out side the colony or site premises including all leads, lifts, loading, unloading, stacking, spreading, levelling etc. complete as per drawings, specifications & as directed by the Engineer in charge. Note: Voids @ 20% for soils and 50% for soft rock/ hard rock shall be deducted from fully loaded truck measurements to arrive at the net quantity for payment in case direct measurement is not possible. Disposing off the surplus excavated materials within 3 km inside the site premises

150mm consolidated thickness.

Supplying and spreading pesticides chlorpyriphos or other chemical approved by central insecticides board as directed by the manufacturer and spraying the mixture uniformly by sprayer as pre-construction anti-termite treatment at the rate of 7.5 litres per sq.m. on vertical and 5 ltrs. per sq.m. on horizontal surfaces (or as directed by the manufacturer) within the trenches, 50% of the emulsion to be filled in the holes made in trenches at 150mm. centre to centre etc. complete as per IS 6313 Part-II. (The payment will be made on the basis of plinth area measurement only at ground floor/ stilt area for all stages of operation and vertical face will not be measured for payment) all complete as per specifications, drawings and as directed by the Engineer in charge. Note: a) This item will be executed through approved agency who is a member of Indian Pest Control Association, approved by Central Insecticides Board. b) The contractor shall have to furnish ten years guarantee in the prescribed Proforma as per Section-10 (iv) Conditions and clauses of contract-2008, to maintain the anti-termite treated area/ structure free from termite. c) Prior approval of Engineer in Charge shall be obtained after testing the chemical for Antitermite to be used and shall be tested in approved laboratory and to be submitted to Engineer in Charge. Cost of testing shall be included in the rates quoted.

Providing and laying damp proof course 50 mm thick at plinth level in cement concrete 1:2:4 using 10mm. maximum size and down graded stone aggregate, mixed with approved water proofing compound at 2% by weight of cement laid to levels, slopes etc. including applying a coat of hot bitumen of grade 80/100 at 17 kg./10 sq.m. including cost of form work, curing all complete as per specifications & as directed by the Engineer in charge.

Providing and laying patent box type cement based water proofing treatment of approved agency for basement raft, vertical walls, lift well & trenches etc. at all levels & locations as per specification of the water proofing agency including cleaning of surfaces, curing and testing the basement raft/ pit for water tightness, rectification of defects if any, etc. complete as per specification and drawing and as directed by the Engineer-in-charge. Notes for waterproofing works:- a) The contractor shall get written approval from the Engineer-in-charge, for the water proofing agency engaged and shall submit the specification of the waterproofing agency before commencement of work. b) The contractor shall test the surface where water proofing treatment is provided for bone dry condition by filling up with water. No wet patches or leaks shall appear on the surrounding wall or under side of the slab. c) The contractor shall furnish guarantee bond on appropriate stamp paper in the Proforma as per Section 10 (iii) of Condition & Clauses of Contract 2008 for the entire waterproofing treatment for maintaining the surroundings and under side surfaces of the water proofing treated area in bone dry condition for 10 years. During the guarantee period the contractor shall attend all leakages, defects etc. if noticed, free of cost, starting the work of checking up and rectification within a weeks time from the date of intimation about such leakages/ defects. Providing 50 mm to 70mm thick waterproofing treatment on horizontal surfaces for base/ floor consisting of i) Ist layer Shahabad stone of approx. size 600 x 600 x 20mm thick of approved quality rough stone slab over a 25mm thick base of ready-mix cement mortar 1:3 (1 cement : 3 course sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion. Joints shall be sealed and grouted with cement slurry mixed with water proofing compound conforming to IS: 2645 in proportions recommended by the manufacturer. ii) 2nd layer of 25mm thick cement mortar 1:3 (1 cement : 3 coarse sand ) mixed with water proofing compound in recommended proportions. iii) Finishing top with stone aggregate of 10mm to 12mm nominal size spreading @ 8cudm/sqm thoroughly embedded in the 2nd layer.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing Shahabad stone of approx. size 600 x 600 x 20mm thick of approved quality (rough stone slab) with cement slurry mixed with water proofing compound conforming to IS: 2645 in recommended proportion with a gap of 20mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior stone slab with ready mix cement mortar1:4 (1 cement: 4 coarse sand) 20mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge.

Structural steel work, using angles, tees, flats, bars, chequered plates, inserts fabricated out of mild steel bars, ISMC, ISMB, angles, pipes, plates, hollow sections etc. of all shapes, sizes at all levels floors and location including supplying, cutting, fabricating, welding, erecting, making holes/ chases wherever required and fixing / embedding in position in concrete/ masonry work with necessary hold fasts/ screws & rawl plugs and finishing the concrete/ masonry work after fixing/ embedding including painting two coats of anticorrosive bitumastic paint on all unexposed surfaces and two coats of synthetic enamel paint of approved make and colour on all exposed surfaces over a coat of approved zinc chromate primer etc. complete as per specifications, drawings and as directed by the Engineer in charge.

Providing & laying NP 3 class of following diameter RCC hume pipe including making holes in masonry/ concrete work wherever required, to be laid in ground/from concrete cable trench to ground, for passing of cables with necessary joints, concrete supports, making good the holes after laying the hume pipe with collar joints using stiff mixture of ready mix cement mortar (1:2) and sealing open ends with wooden bush etc. all complete as per specifications & as directed by the Engineer-in-charge. (Earthwork, road work and PCC for embedment shall be paid under relevant items). 150mm dia pipes

250mm dia pipes

300mm dia pipe

PART I-B : SUPER-STRUCTURE (STRUCTURAL) i) Super structure items included in this schedule pertains to all the works above plinth level upto roof including parapets, water tanks, machine room, terrace level works etc. unless specified otherwise. Reinforced cement concrete of grade M-30 in super structure conforming to IS 456-2000 and 13920 latest edition, at all floors and levels for all structural members in all geometrical shapes/ design as per drawings using graded stone aggregate of 20mm and down graded including machine mixing, conveying, placing in position, mechanical consolidation, finishing, curing, etc. complete all as per drawings, specifications & as directed by Engineer in Charge. Notes for RCC Works: a) All RCC works shall be controlled concrete unless otherwise specified and shall be carried out strictly in accordance with the drawings, specifications and as directed by the Engineer in Charge. b) The water tank work shall be as per IS 3370-2009 latest edition c) The rates for RCC works shall be exclusive of cost of reinforcement and form work unless otherwise mentioned. d) All coarse aggregate to be 20mm maximum size and uniformly graded unless otherwise mentioned. e) For all RCC items, the rates quoted shall include the following without any extra cost to the Dept. i) Spacers to maintain clear cover for reinforcement. ii) Fixing at correct level and in proper alignment the inserts, pipe sleeves, pipe bends, fan hooks, other pipe specials etc. supplied by/ through the Department. iii) Cut out in slabs, construction joints etc. f) Test for concrete shall be done as per IS 456-2000 and the cost of the same shall be borne by the contractor. For all type of Structural/ RCC Elements with all geometrical shape

Extra for providing RMC (Ready Mixed Concrete) conforming to IS 4926 (Latest) in lieu of conventional RCC items, supplied by approved RMC manufacturers including transportation, pumping etc, complete as per instruction of Engineer in Charge. Notes: i) The contractor shall obtain prior approval for RMC manufacturer from Engineer in Charge in writing. ii) The rate shall apply for all levels and locations including all type of structure etc. iii) Extra for RMC in lieu of conventional RCC of any grade mentioned elsewhere in the schedule shall be measured and paid under this item for superstructure works.

Part- I - C - Form Work Notes for form work i) For double/ multi stage shuttering design calculations and details /drawings for scaffolding shall be submitted by the contractor well in advance. Prior written approval of form work shall be obtained from Engineer in Charge, before commencement of work. ii) Area of form work in contact with concrete shall only be measured for payment and stop boards for construction joints will not be measured for payment. iii) The rate of formwork shall include all type of structural/ RCC elements and all geometric shapes including circular and any other curved surfaces at all level and floors including single/ multiple staging etc., complete. Providing, erecting, fixing in position, striking/ removing and cleaning steel/ timber shuttering & centering for form work including single/ multiple staging at all level & locations for all geometrical shapes in plain, curved surfaces of structural/ RCC elements and including rails, bracings, props, brackets, cutting holes for pipes etc., providing & applying approved form oil on all surfaces of form work coming in contact with concrete including close hacking of all exposed concrete work after removal of form work, all materials, labour etc. complete as per specifications, drawings & as directed by the Engineer in Charge. (Area of form work in contact with concrete shall only be measured for payment & stop boards for construction joints etc. will not be measured for payment). For all type of structural/ RCC elements including all geometrical shapes and single/ multiple staging at all floors and location.

Providing, erecting, fixing, centering, shuttering work using ply board to obtain form finished concrete surfaces of F3 finish to ceilings at all heights & locations including single/ multiple staging at all floors and locations for all geometrical shapes in plane, curved surfaces of structural/ RCC elements including chamfers, splays, keys, wedges, props, rails, bracings, brackets, cutting hole for pipes etc. providing and applying approved form oil to all surfaces of form work coming in contact with concrete and striking/ removal of the same including finishing by filling form-tie holes, removal of fins, ridges and irregularities by grinding, filling air holes, with sack rubbed finish cleaning up loose and adhering debris including all materials labour etc. complete as per specifications drawings and as directed by Engineer in charge.

PART - I-D : STEEL REINFORCEMENT WORK Reinforcement for RCC work including supplying steel bars of various diameters as required at site of work including loading, unloading, transporting, decoiling, straightening, cutting, bending placing in position and binding with 18 gauge, soft drawn annealed steel binding wire including carrying out various tests as required etc. all as per specifications, drawings & as directed by the Engineer in charge. (Cost of binding wire shall be borne by the contractor & shall not be measured for payment). Thermo Mechanically Treated bars of grade Fe-500D /550D manufactured by SAIL , TATA STEEL, JSW and RINL only.

PART - I-E : MASONRY WORK Notes: a) The contractor shall get approved the samples of autoclaved aerated cement blocks from the Engineer-In-Charge before procurement on large scale and shall maintain the same for the entire work. b) Necessary Openings/ niches/ pipe sleeves/ cut-outs, wherever required as per drawings and asked for by the Engineer-In-Charge, shall be provided by the contractor without any extra cost. c) Masonry wall thickness shall be considered as 230mm/ 150mm/ 115mm thick and lesser wall thickness if any shall be made up to the required dimensions by the contractor in CM 1:4 using Ready Mix Mortar to proper line, level and plumb without any extra cost to the Department. d) The rate shall include cost of making autoclaved aerated cement blocks masonry to all geometrical shapes and sizes without any extra cost to the Department. Providing and laying autoclaved aerated cement blocks masonry with 115mm/ 150mm/ 200mm / 230mm thick AAC blocks as per approved manufacturer, using approved block laying polymer modified adhesive mortar in super structure above plinth level at all locations, levels & lead with RCC band at sill level and lintel level all complete as per direction of Engineer in-Charge. (The payment of RCC band and reinforcement shall be made for separately)

PART -I-F : FLOORING WORK Notes: a) Adjustment of levels in thickness of mortar bedding due to different types of flooring, if any, shall be done by the contractor without any extra cost to the Department upto theoretical floor thickness of 50mm b) In case theoretical floor thickness is increased to accommodate Raceways/ Electrical service boxes, additional bedding material beyond floor thickness of 50mm shall be paid extra in lean concrete as approved by EIC. c) The contractor shall submit and get approved the sample for flooring, skirting, dado tiles from Engineer in charge before bulk procurement. d) Pattern & design of flooring/ skirting/ dado shall be approved by the Engineer in charge before commencement of work. e) All Exposed edges of all natural stones used for the works like Kotah, Marble, Granite etc. shall be machine cut and shall have uniform thickness, moulded/ chamfered and mirror polished with high gloss finish as approved by Engineer in charge unless otherwise mentioned.f) The rate shall include cost of making Designs/ patterns in the flooring to all geometrical shapes/ curves of different radius and sizes with no extra cost to the Department. (Any curved design/ patterns in flooring/ Dado, tiles/ stones shall be cut using water jet at factory) g) All Kota stone work shall be mirror polished to get high gloss finish and the rate shall be inclusive of the same in the respective item. h) Wherever dissimilar floor finishes are placed adjacent 3mm thick x 25mm wide aluminium flat dividing strips shall be provided by the contractor without any additional cost to the Department. i) The sizes of tiles mentioned are approximate and subject to the availability in market during execution. If the required size is not available the next higher size of tiles shall be used without any extra cost to the Department. The tenderer may note the same and quote accordingly. j) The contractor is to take appropriate step to protect the polishing surface/ glazed surfaces of granite stone, vitrified tiles, ceramic tiles flooring and pre polished Kotah stone for tread and riser by providing and laying 6mm thick POP during construction period without any additional cost. The surfaces are to be cleaned only at the time of handing over. Providing & laying at all floors & locations Somani Vitrified "Duragress Series" tiles or Equivalent (Glossy/ Matt/ Satin) / antiskid as per approved design and pattern of approved manufacturers of following sizes having thickness 8.5 mm or as per manufacturer's specification, tiles conforming to IS 15622 in flooring/ skirting/ dado/ cladding at all floors and location, heights/ levels and lead in approved pattern and colour laid over Ready Mix Mortar bedding/ backing, including cleaning and preparing the surface for bedding, spreading the neat cement slurry, close jointed and grouted with matching coloured ready made cement grout and approved pigment as per manufacturer's specifications, finished to level, line, slope and plumb, cutting of tiles, wastage, making openings/ cut out if necessary, final cleaning of surfaces, curing etc. all as per drawings, specifications & as directed by Engineer in charge. In flooring using tile of size 600 x 600mm laid over 20mm thick Ready Mix Mortar 1:4 bedding and spreading neat cement slurry by using minimum cement about 2kg/sqm prior to bedding and spreading cement paste using minimum cement of about 4.50kg/sqm over bedding, including 3 mm thick and 8mm deep grout line using PVC spacers for creating true alignment and gap between vitrified tile wherever mentioned in drg & the 3mm spacer joints filled with approved epoxy tile grout including providing and laying Durafloor protector XF 3mm thick sheet of M/s. Supreme industries/ equivalent over the whole vitrified tile cleaning the same before handing over without damaging the finished surface & making good if damaged, if any. Note: In case the tiles of prescribed sizes not available , alternate tiles of nearby dimensions of area 0.64 sqm to 1.0 sqm shall be used as approved by Engineer in charge without additional cost to department.

In skirting using tiles of size 600X100mm/1200x100mm laid over 12mm thick Ready mix mortar 1:4 backing. (Rate should inclusive of back coat plaster)

Providing and laying at all floors and levels 6mm.(min.) thick or as per specifications of approved manufacturer first quality matt finished/ anti skid/ rectified ceramic tile flooring /dado/cladding as per the approved pattern and colour as mentioned below in cement mortar bedding /backing, close jointed and grouted with matching cement slurry to match the colour of the tiles, finished to level, line, slope and plumb including cutting of tiles, making openings/ cut-out if necessary, wastage and final cleaning of surfaces as required, curing etc. complete all as per Engineer in Charge. Note: The sizes of tiles mentioned are approximate and subject to the availability in market during execution. If the required size is not available the next higher size of tiles shall be used without any extra cost to the Department. The tenderer may note the same and quote accordingly. In flooring with approved tile of 300x300mm anti skid ceramic tile laid over 20mm thick Ready Mix Mortar 1:4 bedding and spreading neat cement slurry by using minimum cement about 2 kg/sqm prior to bedding and spreading cement paste using minimum cement about 4.50kg/sqm over bedding, including providing and laying Durafloor protector XF 3mm thick sheet of M/s Supreme Industries or equivalent over the whole ceramic tile flooring area along with removing and cleaning the same before handing over without damaging the finished surface & making good if damaged, if any.

In dado/ cladding with 300x600mm size with approved design/ pattern etc. tile laid over plastered surface fixed with Bal-Endura/Fosroc /Roff tile adhesive as per IS:15477 or as approved and as per manufacturer's as backing applied with suitable comb to get 3mm uniform tile adhesive backing after pressing the tile in position, PVC corner bedding/ nosing of approved quality and colour at the corner and edges of the tiles including finishing and embedding in the wall, with 2 nos. decorative bands etc. complete all as directed by the Engineer in charge. The rate is inclusive of back coat plaster.

Providing and laying machine cut and machine polished Kotah stone flooring at all floor & location with necessary cement mortar bedding, close jointed & grouted with matching cement slurry and finished to line, level, curing etc. as required, including cutting of stone slab, wastage, making cut outs, wherever required, machine polishing/ hand polishing (where machine cannot have access) etc. complete all as per specifications, drawings and as directed by the Engineer in charge. In flooring with mirror polished Kotah stone slab of size 600mm x 600mm/ 575mm x 575mm x 25mm thick laid over 20mm. thick Ready mix mortar 1:4 bedding.

In skirting with 20 mm thk mirror polished Kotah stone slab of size 600mm/575mm x 100mm laid over 12mm thick Ready mix mortar 1:3 backing. (Rate should inclusive of back coat plaster)

Providing and laying machine cut and machine polished Kotah stone for treads/ risers/ steps/ ramps etc as mentioned below at all floor & location with necessary cement mortar bedding/ backing, close jointed & grouted with matching cement slurry and finished to line, level, curing etc. as required, including cutting of stone slab, wastage, making cut outs, wherever required, machine polishing/ hand polishing (where machine cannot have access) etc. complete all as per specifications, drawings and as directed by the Engineer in charge. For treads 25mm uniform thick in single piece in length up to 1250/ 1500mm (approx.) laid over 20mm thick Ready mix mortar 1:4 bedding including providing factory cut three Nos. of antiskid grooves including half round moulding the edges etc. complete.

For risers 20mm thick in single piece (length up to 1250/ 1500 mm (approx.) laid over 12mm thick Ready mix mortar 1:4 backing (Rate should inclusive of back coat plaster)

In slopped skirting with 20 mm thk mirror polished Kotah stone slab of size 600mm/575mm x 100mm laid over 12mm thick Ready mix mortar 1:3 backing. (Rate should inclusive of back coat plaster)

In Ramps with 100 mm wide strips and 20mm thick of maximum 1500mm length laid over 20mm thick Ready mix mortar 1:4 bedding.

Providing & laying machine cut machine polished natural stones as mentioned below for kitchen platform/ wash basin counter topping, vertical and Horizontal facia over and including necessary ready mix cement mortar for backing/ bedding, close jointed and grouted with matching cement slurry and finished to line, slope, level, plumb, curing etc. as required including cutting of stone slabs, wastages, making cut outs wherever required etc. all as per specifications and as directed by the Engineer in charge. i) For kitchen platform/ wash basin counter top, upto 600mm wide in single piece in combination, consisting of machine cut machine polished on one side minimum 35 mm thick cuddapah stone at bottom and mirror polished machine cut 18 mm thick Jet black Granite stone at top fixed with 47 mm thick 1:4 ready mix cement mortar, between two stone slabs (Double stone slab sandwich type) including providing cut out if any to fix Sink/ wash basin, including necessary cement paste, moulding and polishing the edges, providing required slope to drain away water, etc. complete.

ii) For facia, in kitchen platform facia / wash basin counter facia upto 100 mm wide / 300 high vertical sides / or any other size as shown in the drawing, machine cut machine polished 18mm thick jet black Granite stone, half round moulded wherever required fixed with epoxy resin based adhesive, with clamp/ pins as per requirement, including round moulding and polishing the edges etc. complete. iii) For vertical support of wash basin counter/ kitchen platform/ shelves/ racks etc., consisting of 2 nos 35 mm thick cuddapah stones, machine cut machine polished on exposed sides, placed back to back, sandwiched between the stones with 30 mm thick CM1:4 (Using factory made Ready Mix Mortar only). iv) For vertical support of wash basin counter/ kitchen platform etc., consisting of 1 no 35 mm thick machine cut machine polished on one side cuddapah stone slabs and other side 18mm thick jet black granite stone back to back, sandwiched between the stones with 47 mm thick CM 1:4 (Using factory made Ready Mix Mortar only) including rubbing and polishing of cut edges all in line, level, plumb etc. complete. Notes :- i) Only top clear exposed plan area of the combined slab system shall be measured for payment and area of bottom slab, cuddapah sandwich vertical support, granite facia etc. shall not be measured. ii) The rate shall be inclusive of making necessary recess in masonry wall to provide minimum bearing of 25mm for the sandwich slab system. iii) The thickness of cuddapah stone shall be 35mm (+) or (-) acceptable tolerance. The agency may quote accordingly. Providing and fixing at all floors & levels, machine cut and machine pre-polished on top, bottom & exposed edges, 35 mm thick cuddapah shelves of uniform thickness including cutting recesses alround in wall embedding (minimum 25 mm alround) with Ready mix cement mortar 1:3 or in case of concrete member supported over 40x40x6 mm MS angle to the correct line, level, curing, making good the surfaces etc. complete all as per specifications, drawings and as directed by the Engineer- in-Charge. (The cost of MS angle shall be paid separately under relevant item.) Note: Only area of exposed top surface of shelves shall be measured for payment under this item.

Providing, machine mixing and laying in approved Panels of 40mm thickness IPS flooring in cement concrete mix of 1:2:4 using graded stone aggregate of 12mm maximum size with colouring pigment, at all levels, well vibrated, compacted including providing and fixing 25mm x 3mm thick aluminium dividing strip, laid in panel of size not exceeding 2.00 sqm, to correct level and finished smooth, curing including preparation of surface by cleaning, hacking and exposing aggregate to achieve the bond, all complete as per specification, drawing and as directed by Engineer in charge.

Cement plaster 20mm thick in skirting with Ready Mix Mortar 1:4 finished smooth with a floating coat of neat cement, correct to line, level and plumb including rounding of junctions with flooring etc. complete as per specifications, drawings & as directed by Engineer in charge.

Providing and fixing in position at all floors, levels/ heights 16mm thick mirror polished natural stones slab for door frame/window frames in two overlapping layers one piece full length/ height of approved shade, finished sizes as directed including machine cut/ hand cut, final cleaning, moulding and polishing of all exposed edges, in line, level, plumb and fixing the stone with ready mix cement mortar 1:3, 20mm backing & overlapping of 20mm shall be fixed with Araldite adhesive, with best workmanship, finishing, including curing, scaffolding, providing 75mm long SS screw minimum @600mm c/c etc. complete all as per specifications, drawings & as directed by the Engineer- in- Charge. 16 mm thick machine cut and single side mirror polished Baroda green marble stone for window cill, jamb etc. including half round moulding & polishing of exposed face etc complete.

Providing & fixing in position second class approved quality teak wood moulded, rebated frames of finished size as shown in drawing, conforming to IS : 4021-1995 for kitchen cabinet / cupboard/ exhaust fan/ door frame etc. at all heights and locations including making holes in concrete/ masonry walls, including providing and fixing MS hold fasts 300mm x 30mm x 3mm thick embedded in plain cement concrete 1:3:6 in case of brick work and M.S coach screw 100mm long or of equivalent size in case of RCC/ stone works, painting two coats of bitumastic paint for all unexposed surfaces coming in contact with concrete/ masonry and painting the exposed surface with two coats of synthetic enamel paint of approved make and shade over a coat of approved primer etc. complete all as per drawing, specification and as directed by the Engineer in Charge. (Finished size will be considered for payment.)

Providing and fixing 19/12mm thick marine ply for wardrobe/ cabinet, cupboard, kitchen cabinet, drawers etc.at all floors and levels consisting of single or double leaf shutters, shelves, sides supports bonded with phenol formaldehyde resin, shutter of approved manufacturer, with second class teakwood lipping of size 18/12mm X 8mm all round shutter, shelves and side supports and 18mm x25mm at Z shape / flat meeting style of shutter including providing and fixing 1.5/1.0 mm thick decorative laminate sheet of approved make, colour and shade fixed over both sides, exposed edges etc. with approved adhesive as shown in the drawing including cost of all materials, adhesives labours, wastages, fixing of fitting and fixtures(cost of fitting & fixture will be paid under relevant item ) painting the non laminated surface and edges with Synthetic Enamel paint etc. all complete as per specification, drawing and as directed by Engineer-in-Charge. Marine ply 19mm thick finished with synthetic enamel paint on both sides of shelves.

Marine ply 12mm thick finished with 1.0 mm thick laminate on one side and synthetic enamel paint on other side of the drawers.

Marine ply 19mm thick finished with 1.0 mm thick laminate over one side of the vertical partitions.

Marine ply 19mm thick finished with 1.0 mm thick laminate over both side of the vertical partitions

Marine ply 19mm thick finished with 1.5 mm thick laminate over one side of the shutters.

Marine ply 19mm thick finished with 1.5 mm thick laminate on one side and 1.0mm thick laminate on other side of the kitchen and drawers

Supplying & fixing in position the following type Exterior grade flush door shutters with both side laminate of approved make and shade conforming to IS 2202 (latest) of M/s Kalpataru, M/s. Anand, M/s Kutty or of approved equivalent with external/ internal type second class teak wood lipping of require sizes alround, fixing shutters in position to pressed steel door frames/ wooden frames/ granite frame works (door frames shall be paid separately under relevant item) at all floors by cutting/ planning if necessary including labour for fixing of the fitting and fixtures as per drawing with wooden packing pieces if necessary (but excluding the cost of fittings and fixtures with SS screws which shall be paid separately under relevant item), including vision panel if required as per drawing including painting/ polishing with two coats of synthetic enamel paint with primer / melamine polish of approved make & shade etc all complete as per specifications, drawings & as directed by Engineer in charge. Note:- Decorative veneer/ lamination sheets shall be hot pressed at factory during manufacturing of door shutters. 38mm thick single leaf flush door shutter prelaminated with minimum 1.5 mm thick laminate of approved make & colour on both side with 200mm x 750 mm vision panel 5 mm thick clear glass.

38mm thick double leaf flush door shutter prelaminated with minimum 1.5 mm thick laminate of approved make & colour on both side with 200mm x 750 mm vision panel 5 mm thick clear glass.

Providing & fixing fire rated door frame & shutter system at all floors & locations using system of approved manufacturer or approved equivalent, the non-metallic wooden door frame & shutter system having 60 minute (1 hr) fire rating, asbestos free, fully insulated composite fire resistant conforming to BS:476, part 20-22, integrity, insulation and stability (3 criteria: fully insulated) as per IS:3614 Part 2, as per prototype tested & certified by Fire Research Laboratory, like CBRI Roorkee, IPIRTI, Bangalore, with standard heating conditions as specified in IS:3809-1979 and BS:476 (Part 20 - 22)-1987 to achieve the required integrity & insulation (i.e. to restrict the heat radiation, temperature rise on the non fire side to the maximum of 140 degree centigrade above the ambient temperature on the unexposed surface of the shutter) (a) Door Frame-The fire rated, non-metallic engineered wooden door frame of section 150 mm X 75 mm with 2 Nos of intumescent strip (imported) on all three members to take care of hot smoke. the size of the intumescent strips shall be 10 mm X 2 mm, concealed in the groove of the frame. Installation of the frame to be done with specially designed door anchoring systems so that there are no holes in the frames. The anchoring system shall have 3 anchoring points on each side of the frame that shall secure the frames in the floor as well as on the wall. The frame anchoring system shall be secures with 4 anchor fasteners on each side (2 per set) for any type of wall except brick walls, In case of brick work, M.S coach screw 100mm long or of equivalent size shall be used. The entire anchoring system should be concealed between the frame and the wall. Architraves : Telescopic type architrave to take care of 10mm variation in the wall width to be provided. This should be manufactured from Marine grade calibrated ply as per IS 710. Foam: All gaps between the wall and the frame should be filled with imported Fire retardant PU foam of Brand Multifoam or equivalent. The entire set shall be decorated with approved shade of 1.00mm thick decorative fire retardant laminate sheet of approved colour, pattern & shade fixed on both sides etc. with approved adhesive machine pressed for all surfaces including edges including cost of all materials, adhesives, labours, wastages if any.(b) Door Shutter-The fire rated, non-metallic wooden door shutter (single / double leaf) of not less than 55 mm thick made out of wooden perimeter railing (stiles & Rails). The hollow section in the perimeter railing should be filled with high density ceramic wool. this assembly to be layered with MGO board of thickness 8 to 10mm on both sides further supported with Marine grade calibrated ply as per IS 710 on both sides. Smoke intumescent seal of size 20 mm X 4 mm with casing to be mounted in the grooves in the shutter on all sides except bottom with wooden beading on all side. Including providing and fixing 1.0 mm thick decorative HPL (High Pressure Laminate) or decorative ply based veneer sheet of approved colour, pattern & shade fixed on both sides etc. with approved adhesive; machine pressed for all surfaces including edges including cost of all materials, adhesives, labours, wastages if any. Hinges: Minimum 4 Nos of Fire Retardant hinges shall be supplied with the Shutter to be supplied by manufacturer without any extra cost to the department as per the fire norms and as approved. Slotting: The shutter shall be prepared for installation of any type of hardware at the factory. Vision Panel: If any shall be fire rated 6mm glass of Scott Pyran or equivalent thoroughly held on both sides. The minimum width of the glass has to be 200/300mm and Maximum length can be 1000mm.(c) Installation & Certification-The installation of door frame & shutter system shall be from approved licensed agency of Local Statutory Authority for installation of fire door frame & shutter system to be submitted by agency and Fire Resistant certification as required by Local Statutory Authority shall be furnished by Manufacturer of Fire rated door frame & shutter system including Form "A", etc all complete as per specifications, drawings & as directed by Engineer in charge. ( Note:- The outer to outer length & width of frame only will be measured for calculation of area of payment) upto door Size 2.50 X 2.50 mtr with double leaf shutter and as per Architectural / CFO requirement.

Supplying & fixing 25 mm thick PVC integral free foam sheet in form of flush finish door shutter, manufactured by M/s.Jain Irrigation Systems Ltd. (Ex-cell sheet) , Rajashree Plastiwood or other equivalent approved make of white colour, solid section, extruded rigid, light weight sheet with fine & homogeneous closed cell structure with smooth, glossy, hard surface finish on both sides including providing recessions for hinges and providing & fixing 3 nos 100 mm heavy duty S.S. hinges and 2 Nos. 100 mm heavy duty SS baby latches, 2 nos. of 150 mm SS Bow handles with back plate of M/s Shalimar Hardware or approved equivalent and including providing an opening of size 300 mm X 200 mm including providing and fixing PVC moulded louvers on both faces in the opening with ss screws, all edges to be smooth finish with mixture of PVC powder & solvent etc complete all as per specifications and as directed by the Engineer-in-Charge.

Providing & fixing in position approved quality 2nd class teak wood architraves of finished section of approved profile for the following sizes fixed to pressed steel frames of door/ cup board/ MS doors at all floors as per drawing including providing and fixing M.S. self taped screws at 600mm center, painting with two coats of synthetic enamel paint of approved make, & colour over one coat of approved primer etc. all complete as per specification & drawings.

Supplying and fixing in position at all floors integrated bronze anodised matt finished [15 micron thick], aluminium section [extruded] for aluminium Door/ windows sliding/top hung/ fixed/ openable/grill/ adjustable louvered/ windows as per drawing of approved manufacturers with extruded sections of M/s Jindal/ Hindalco or other approved equivalent sections with size and weights as shown in the drawing, for frames and shutters [including wastages if any] conforming to relevant I.S specifications with all approved Bronze anodised aluminium fittings and accessories, locking arrangements, 2/ 3 rollers with ball bearings for sliding shutters of approved quality all as shown in the drawing, including providing and fixing aluminium channel beading/ glazing clips fixed with necessary bronze anodised screws, grouting the gap with thermocole & polysulphide sealant etc. all complete generally as per drawings, specifications etc., all as directed by Engineer in charge but excluding the cost of glazing, which will be paid separately. Note: 1) Sliding window sections for both track & Shutters shall be of JINDAL DELUXE DOMAL SERIES or similar equivalent approved make. 2) Approval of the Dept. for the complete design and shop drawing shall be obtained before commencement of the work. Aluminium for Doors and windows

Providing and fixing following type of approved quality glass panes for doors/ windows/ ventilators of M/s. Modiguard/ M/s Saint Gobain or approved equivalent and fixing with aluminium/ upvc frame work including fixing aluminium channel beading (to be paid under relevant item) and providing and fixing with 2 way EPDM gasket, to ensure water and air tightness and neoprene cushions/ gasket accommodated in grooves, necessary bronze anodised screws etc., all complete generally as per drawings, specifications and as directed by the Engineer-in-charge. 6 mm thick clear float glass

6 mm thick frosted/bajra glass for louvers

Supplying and fixing in position at all floors and location stainless steel 304 grade mosquito net made out of 24 gauge 16 mesh shutters of various size and shape fixing with stainless steel nuts and bolts to suit the aluminium frame fixed in sliding/ openable/ fixed windows conforming to IS:1948-1961 as per drawing (aluminium frame, beading etc. shall be paid under relevant item) including labour wastage scaffolding etc. all complete as per drawing, specification and as directed by Engineer in charge.

PART : I-H : FITTING & FIXTURES: Notes: i) One sample board consisting of each item of schedule of quantities with approved quality fittings & fixtures & necessary accessories including chromium plated brass screws, bolts, nuts, washers should be submitted for approval of Engineer-in- charge. Large scale procurement shall be taken up only after approval of the Engineer-in-charge. After approval, the samples shall be kept in the office of the Engineer-in-charge to ascertain the approved quality for the entire work. ii) All fittings & fixtures shall conform to relevant IS code. Supplying at site of work approved quality and manufacturer (M/s Shalimar or other approved) Stainless steel (SS-304) fittings, fixtures and fastenings along with Stainless steel screws, bolts, nuts, washers, wooden packing pieces if necessary etc. and other accessories etc complete. Tower bolt 300mm. long x 12mm dia. barrel.

450 LONG 40 DIA SS HANDLE

Aldrop 250mm long x 16 mm dia. rod with extra staple.

Safety chain with staple link

Door stopper with twin rubber bushing (shutter mount type)

Heavy quality Magnetic catch

Supplying at site of work approved quality non magnetic stainless steel fittings, fixtures and fastenings along with necessary SS screws, bolts, nuts, washers etc. wooden packing pieces if necessary etc and other standard accessories complete as per approved samples. Butt Hinges of following sizes as per relevant IS code. 125x76x3mm

Box type soft close heavy duty cabinet hinges of M/s Godrej or approved equivalent as per drawing and specifications.

Supplying following type of approved quality miscellaneous fittings, fixtures and fastenings along with necessary SS screws, bolts, nuts, washers, wooden packing pieces if necessary etc. and other standard accessories. Supplying 6-lever Mortice lock of chromium plated brass parts & body, of Godrej make model no. 7117, 200mm Door Handle Set on both sides, with Lock Body 1CK (1 Cylinder,1 Knob, Operable by key from one side)Mortice Lock with chromium plated brass screws etc. lock shall be fitted as per manufacturer's specification and as directed by Engineer in charge.

Supplying and fixing at all floors and levels IS : 3564 marked aluminium extruded section body tubular type universal fire rated hydraulic Door Closer of M/s Everite, Ms Godrej or equivalent manufacturer with double speed adjustment with necessary accessories and necessary screws ets. complete of M/s.Everite all as per specifications and directed by Engineer in charge.

Supplying and fixing at all floors and levels SS TADI LOCKING ARRANGEMENT 200 mm long and Size 12 x15 mm as per approved sample with necessary accessories and necessary screws ets. complete of M/s.Everite all as per specifications and directed by Engineer in charge.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315 ( Make of Hardwyn or Dorma), having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-Charge.

PART - I-I : WATERPROOFING TREATMENT: a) The contractor shall get written approval from the Engineer in Charge for the water proofing agency engaged and shall submit the specification of the waterproofing before commencement of work. b) The contractor shall test the surface where water proofing treatment is provided for bone dry condition by filling up with water. No wet patches or leaks shall appear on the surrounding wall or under side of the slab. c) The contractor shall furnish guarantee bond on appropriate stamp paper in the Proforma as per Section10 (iii) of Conditions and Clauses of Contract - 2008 for the entire waterproofing treatment for maintaining the surroundings and under side surfaces of the waterproofing treated area in bone dry condition for 10 years. During the guarantee period the contractor shall attend all leakages, defects etc. if noticed, free of cost, starting the work of checking up and rectification with in a week's time from the date of intimation about such leakages/ defects. d) The Contractor shall keep the water tank filled with water after the water proofing work has been completed and shall clean it before handing over. At no time shall the water tank be kept empty. Testing for the bone dry condition for the water proofing work carried out shall again be done, before handing over the Building/ flats, if found necessary by the Engineer in Charge.e) Wherever Cement mortar is to be used it shall be with Ready mix mortar for all waterproofing work with suitable proportioning for richer mix. Providing and laying integral cement based water proofing treatment of the agency approved by department, including preparation of surface as required for treatment of roofs, terraces etc mixing with waterproofing compound as per IS : 2645 :2003, with average thickness of 115mm and minimum thickness at drain point as 65 mm. Following works are included in above item. a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm. Of cement admixed with proprietary water proofing compound over the RCC slab including cleaning the surface before treatment. b) Laying cement concrete using broken bricks/ brick bats 25mm to 100mm size with 50% of Ready-mix mortar 1:4 (1 cement : 4 coarse sand) admixed with proprietary water proofing compound over 20 mm thick layer of Ready mix mortar of 1:4 (1 cement : 4 coarse sand) admixed with proprietary water proofing compound to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs. c) After two days of proper curing applying a second coat of cement slurry admixed with proprietary waterproofing compound. d) Finishing the surfaces with 20 mm thick joint less cement mortar using ready-mix C.M 1:4 (1 cement : 4 coarse sand) admixed with proprietary water proofing compound and finally finishing the surface with trowel with neat cement slurry & making pattern of 300x300mm square 3mm deep or suitable to receive the China Mosaic waterproofing treatment wherever specified. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer in Charge.

Extra for additional thickness of brick bat coba using ready mix mortar over and above standard average thickness of 115 mm. for effective slope wherever required.

Filling in bath, W/C, toilet, depressed areas with water proofing brick bat coba of the agency approved by the Dept. at all floors and locations up to the required level and making the surface finished suitable to receive floor finish etc. all complete as per drawings and water proofing agency's specifications with 50% of Ready-mix mortar 1:4 (1 cement : 4 coarse sand) admixed with proprietary water proofing compound over 20 mm thick layer of Ready mix mortar of 1:4 (1 cement : 4 coarse sand) admixed with proprietary water proofing compound to required slope and treatment & as directed by the Engineer in charge.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., Kitchen and the like consisting of : i) 1st course of applying cement slurry @ 4.4. Kg/sqm mixed with water proofing compound `Impermo' of Snowcem or equivalent conforming to IS 2645 in recommended proportions. ii) IInd course of cement plaster 1:3 (1 cement : 3 coarse sand) using Ready Mix Mortar mixed with water proofing compound in recommended proportions, 20mm thick up to finished floor level and 15mm thick above finished floor level up to 600mm. iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg per sqm of area. iv) IV th course of 200 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.)

Providing cement based water proofing treatment by 'Injection & Surface' method of the agency approved by the dept. cement based water proofing treatment of 50 mm. and 20mm. thick for the floor and walls respectively at terrace water tanks, finished perfectly smooth to correct line, level and plumb including preparing the existing surfaces, necessary scaffolding, curing etc. complete as per waterproofing agency's specifications and testing water tank for the water tightness and rectification of defects, if any, to render the outer surface bone dry etc. complete as per specifications, drawing and as directed by the Engineer in charge.

Providing China Mosaic water proofing over concrete/plastered surface of horizontal, vertical, sloped/ curved surfaces, rounded vatas, sharp corners, junctions etc., using broken pieces of approved colour ceramic tile laid over and including 20mm thick cement mortar 1:3 screed mixed with approved waterproofing compound @ 2% by weight of cement, cost of all materials, labour, curing, breaking the tiles to the pieces of required size and shape, laying / fixing the tile pieces to the required line, slope, levels etc., providing extra screed as required for quick & easy flow of water, curing etc., at all heights including necessary scaffolding, cleaning the surface initially with saw dust and finally with acid all asper specifications and as directed by the Engineer-in-Charge.

PART I - J : PLASTERING WORK : Note: a) Before commencement of plastering, the area shall be cleaned, wetted and shall be marked with 'Thiyyas' or 'Tapanis' and shall be got approved by the Engineer-in-charge. b) Whenever the electrical contractor/ agency has to fix up switch boxes in walls, necessary Thiyyas or 'Dhadas' shall be arranged prior to plastering so that the electrical boxes are fixed properly in line with the finished plastered surfaces. c) Finishing around the junction boxes shall be done at all floor, level and position to the line, level and right angles as required while carrying out plastering work. d) No extra claim/cement consumption shall be entertained by the department for the plastering done more than the specified thickness shown in the schedule of quantities, to bring the plastered surface to perfect line, level and plumb with adjoining columns and beams. e) Only Ready mix Mortar of approved make shall be used. For richer proportion additional cement to be added in required proportion. Cement plaster using READY MIX MORTAR (RMM) of approved manufacturer (Roofit Mix, Wallplast, Readiplast, Silcoplast) in single/ double coat as specified over Concrete surfaces in thickness as mentioned, in C.M 1:4 or richer by proportionally increasing cement content as required, over plane or curved surfaces at all level including rounding of surfaces wherever required, prepare the surfaces even and smooth in correct line, level, plane and plumb including scaffolding, chemical curing etc. complete as per specification drawings and as directed by the Engineer in charge. 15 mm thick cement plaster using RMM 1:4 mix for internal brick / concrete surfaces for all walls and beams flush with walls, mullions etc.

Sand faced cement plaster as mentioned below in CM 1:4, using factory manufactured pre mix/ ready mix of 'Roofit Mix' of M/s Premier Floor to Roof Materials pvt.ltd/ 'Build Well ready mix plaster' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd / Readymade polymerised Dry mix Plaster - Silicoplast of M/s. Precise Conchem Pvt. Ltd.or other approved equivalent make, having minimum composition of Cement : Sand as 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces final rendering, including using richer mix for making corners if necessary and making nosing / dripmould in plaster wherever required, at all floors, levels, all heights and locations including scaffolding, preparing the surfaces, finishing and rendering with sponge to correct line, level and plumb, curing/ chemical curing etc. complete as per specification and drawings and as directed by Engineer-in Charge. 20 mm thick in two coats for brick/ concrete surfaces (external / internal) (back coat and finishing coat of 10 mm. thick each) with water proofing agent @ 2% by weight of cement or as per manufacturers specifications

12 mm. thick in single coat for independent concrete surfaces with waterproofing agent @ 2% by weight of cement or as per manufacturers specifications.

Providing vatas 150 x 150 mm at junction of walls and chajjas canopies etc. with cement mortar 1:3 using Ready Mix Mortar (RMM) of approved manufacturer to match surrounding plaster to the required profile including adding water proofing compound @2% by weight of cement or as per manufacturer's specification, scaffolding‚ curing etc. complete as per specifications and drawings and as directed by the Engineer-in-charge.

Extra over plastering items for making grooves of 16 x 8mm size as shown in elevation drawing at all floors and locations to proper line, level and plumb, all as per specifications, drawings and as directed by Engineer in charge.

Extra over plastering for making drip mould of size 25mm x 10mm .

Providing & fixing in position GI chicken wire mesh (Hexagonal shape) of M/s Arpita Plaster mesh or approved equivalent, of 12mm size hole, 22 Gauge with necessary "U" hooks, clips or nails at all floors and levels, wherever required to prevent development of cracks in plaster surfaces, as per specifications, drawings and as directed by the Engineer in charge (Only area of chicken wire mesh provided shall be measured for payment).

Providing and applying 1.5 mm thick cement based wall care putty in two coats of approved manufacturers at all floors and locations, over plastered surfaces finished smooth to correct line, level, plane, plumb etc., including preparing the surfaces, scaffolding smoothen the putty surfaces with very fine water proof emery paper to get a glossy finish etc. complete as per specifications, as per manufacturers specifications, drawing & as directed by the Engineer-in-charge.

Painting plastered/ concrete surfaces with two coats of acrylic premium (plastic) emulsion paint of approved colour and make over a coat of approved cement/ Acrylic primer including preparing the surfaces, filling with putty wherever required, scaffolding and cleaning etc, complete as per specifications, drawings and as directed by the Engineer in charge.

Painting plastered/ concrete surfaces with two coats of exterior grade Acrylic emulsion paint of approved manufacturer and of approved colour and shade over a coat of acrylic based water repellent primer of approved make and shade as mentioned below all as per manufacturer's recommendations and as per the approved sample and pattern including providing necessary scaffolding, cleaning the surface with water to remove all coating, dust, filling up cracks & crevices with approved putty, curing the surface etc. complete as per specifications and as directed by Engineer in Charge. a) Over sand faced plaster and jalli Note:- Both sides of the jalli shall be measured for payment.

PART : I-L : MISCELLANEOUS WORKS Note: One sample of each item should be submitted for preliminary inspection and approval before procurement/ manufacturing on large scale. After the preliminary inspection and approval, the sample should be fixed at site or kept in the office of the Engineer-in-charge till completion of the work. Providing and fixing of 100% eco – friendly Light weight calcium silicate inorganic modular Acoustical light weight grid ceilings at all heights having 15 mm thick integral densified edges of Tegular/board edged of Size 595x595MM of M/S Aerolite Industries Pvt.Ltd. Manufactured using Non cementitious Calcium silicate Binders reinforced with eco- friendly inorganic Fibres with Minimum eco-friendly recycled content of 50% (For Green Buildings). The ceiling Tiles should be free from Chemicals, asbestos having Zero VOC for better indoor Air Quality as per requirements of IGBC / Griha. The ceiling tile should be of approved texture, design and patterns like Spectra / Quadra Spintone / Cosmos / Globe / Hexa / Plain having NRC (Noise Reduction coefficient) of 0.50 to 0.75 (for semi perforated and fully perforated range of tiles), Light reflectance of 85% (minimum). False ceilings shall be Tested and classified to fire classification class of A1(Non – Combustible), S1(Zero Smoke), d0 and it should be Mandatorily 100% Non-combustible as per BS: 476 Part IV, Part VI for Non-Flame spread & Part VII for Non flame Propagation & also classified as Non ignitable and smoke developed of 0-5 only in accordance with ASTM-E84 as per requirements of UL 723/ NFPA 101 of international building safety code. False ceilings must have 100% RH Property guaranteed for 10 years free replacement for sagging/warping and bending. Thermal conductivity of 0.043 W/m°KC to 0.050 W/m°KC as per IS 3346/1980 (High Thermal Insulation). 100% Antifungal, Antibacterial confirming to JIS-Z-2801 and ASTM- G-21 certified by NABL accredited labs. The tiles shall have Thickness: 10 mm thick in the centre and 15mm thick all around on edge resting portion with integral densified edge. 350 kg/M3 in the centre 10 mm thick portion and 450 Kg/M3 cube on the edges, (Average 360 kg per cum as per ECBC Code 2007).The framework shall be suspended from ceiling by slotted cleats of size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners and to be suspended by Galvanised 6mm Threaded rod up to 1000 MM Length with Galvanised L Shaped level adjuster of Size 76Z25 X 25 X 1.6mm length with MS Z Cleat of size 25 X 37 X 25 X each 1.6 MM with Pre-cut hole on the 25 mm Flanged, spaced at 1200mm centre to centre. The tile shall be laid on Main runner of size 24x32X0.3MM having 24 MM flange colour white having rotary stitching on all T sections, i.e., the main runner, 1200 mm & 600 mm cross tees with a web height of 28mm &0.3 thickness & load carrying capacity of 11-15kgs/Sqm. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge/Manufacturers Specification.

Structural steel work, using angles, tees, flats, bars, chequered plates, inserts fabricated out of mild steel bars, ISMC, ISMB, angles, pipes, plates, hollow sections etc. of all shapes, sizes at all levels floors and location including supplying, cutting, fabricating, welding, erecting, making holes/ chases wherever required and fixing / embedding in position in concrete/ masonry work with necessary hold fasts/ screws & rawl plugs and finishing the concrete/ masonry work after fixing/ embedding including painting two coats of anticorrosive bitumastic paint on all unexposed surfaces and two coats of synthetic enamel paint of approved make and colour on all exposed surfaces over a coat of approved zinc chromate primer etc. complete as per specifications, drawings and as directed by the Engineer in charge.

Supplying, applying and placing swellable type water stop tape of size 19mm x 25mm thick of expansive nature for construction joints of RCC walls of water tank including cleaning the construction joints of loose mortar and dust, applying primer @ as per manufacturer's specification, unroll the water bar slowly and carefully on the joint without pulling and stretching it too much after the primer dries a little and became sticky and tying with the reinforcement bars as directed all complete as per manufacturer's specification and as directed by Engineer in charge.

Providing & laying average 100 mm thick or as shown in the drawing, Cement concrete coping of mix 1:1.5:3 over window/ Ventilator Cill, parapet wall, etc. including mechanical mixing, consolidation, finishing, making slope, curing, formwork including cost of plastering with Ready Mix Mortar in CM 1:4, 20mm thick, etc. finished with neat cement all complete as per drawing, specification & as directed by Engineer in charge.

Providing and fixing in position at all floors and levels, precast GRC jali of 50mm thickness of approved design and pattern and approved manufacturers as per drawing, including transporting the jali, fixing the same in position in cement mortar 1:3 to the pattern, finishing with white cement wherever required as shown in the drawing, scaffolding, curing etc., complete all as per drawings, specifications and as directed by the Engineer in charge.

Providing & fixing stainless steel pipe hand rail at Staircase& lobby, all floors & levels conforming to 310 Grade of steel, of Schedule 10-S , having 1000mm height approximately. Pattern is 50 & 25 mm dia.NB Pipe inhorizantal,40mm dia NB pipe in vertical. All as per approved pattern &design shown in drawing including necessary S.S bend,tees, welding / nut-bolt necessary anchoring polishing and fixing in concrete/brick wall with S.S lugs, making pockets,concreting, making good the surfaces etc. as per specifications drawings and as directed by the E-I-C.

PART - II :- Internal Public Health Engineering works SCHEDULE OF QUANTITIES GENERAL NOTES: 1)Tenderers are advised to check the scope or work from point no. 1 to 13 in the tender document. Part II-A : Sanitarywares & C.P Appurtenances. Note:- 1) All sanitaryware shall be provided from same brand 2) All CP fittings / Fixtures from same brand shall be provided. Providing and fixing in position following Vitreous China Wall Hung type Wash down pattern water Closet consisting following items of work:- I) Providing Vitreous China wall hung type wash down pattern Water Closet ( EWC ) conforming to IS 2556 (part XVI) with integral "P" trap outlet with water seal not less than 50 mm with vent and necessary C.I. brackets supports. ii) Providing thermosetting or thermoplastic Seat & cover conforming to IS 2548, fixing seat & cover for water closet as per manufacturer's specification including the cost of corrosion resistant hinges, bolts, nuts, non ferrous or S.S washer etc. all complete. iii) Fixing the Water closet in position, jointing the trap, water closet and UPVC pipe by Epoxy grout or Rubber seal as per pipe manufacturer. iv) Cutting hole, making grove or chases in the wall, floors, slabs etc., reinstating to it's original condition after completion of work, painting all metallic parts with two coats of flat oil paint of approved make & shade over a coat of primer, finishing the gaps with white / matching colour cement etc. all complete. v) Testing the system to the full satisfaction of the Engineer-in-Charge. Vitreous China European Water Closet of Starwhite/snow white/bright colour with P trap of "Hindware" Cat. No. 20069/20097 Lara model with slow falling seat cover or Cera cat. No. S1041111 Cruse model with slow falling seat cover or Parryware Cat. No. C0264 Cardiff model with slow falling seat cover.

Providing Flushing arrangement to Water Closets including providing and fixing manually operated PVC low level Flushing Cistern consisting following items of work:- i) Providing PVC low level flushing cistern with all inside syphonic fittings, duly assembled conforming to IS 7231 of in etc.as per the manufacturer's recommendation all complete.position using CP brass screws, rawl plugs, brackets approved make with handle, fixing the cistern. ii) Providing 40/32 mm dia.uPVC (6Kg) flush pipe from Flush tank to Water Closet, concealed in the wall as directed making connection with W.C pan including the cost of fittings, fixtures and jointing materials etc. all complete including providing & fixing 15 mm dia. PVC coupling with mosquito proof jalli at overflow outlet. iii) Cutting hole, making chases in the wall, floors, slabs etc. and reinstating the surface to the original condition,painting all metallic parts with two coats of flat oil paint of approved make and shade over a coat of primer,finishing the gaps with white/ matching cement etc. all complete. iv) Testing the entire system to the full satisfaction of the E.I.C. v) Flushing cistern and WC shall be from the same manufacturer. Flushing arrangement with low level Dual Flush Cistern of Starwhite/snow white/bright colour as per Hindware "Sleek Essence Dual Flush" model or Cera cat. No. B1020106 "Compass Twin Flush" model or Parryware Cat. No. E8110 "Slimline Dual Flush Deluxe" model for WC.

Providing and fixing first Quality Vitreous China Counter type Wash Hand Basin Consisting following items of work:- Providing Vitreous China over the counter type Wash Basin of Star white ( standard ) colour of following make conforming to IS 2556 and placing it in position over the granite platform as shown in the drawing or as directed including finishing the joints with white cement all complete. i) Providing Wash Basin and placing it in position as shown in the drawing or as per manufactures specification or as directed including finishing the joints with white / matching colour cement all complete. ii) Providing/Fixing various CP fittings such as Waste Coupling of Jaquar Cat No. 705/709, Bottle Trap of Jaquar Cat. No. 769 including fixing 32 mm minimum 10kg class PVC pipe conforming to IS:4985 (and fittings conforming to IS:7834). Placing and fixing Waste Pipe from Bottle trap to adaptor / Nahani trap / Floor Trap. iii) Fixing the Wash Basin in position, including providing M.S./C.I. Brackets & SS screws for the basin. iv) Cutting hole, making grove or chases in the wall, floors, slabs etc., reinstating to it's original condition after completion of work, painting all metallic parts with two coats of flat oil paint of approved make & shade over a coat of primer, finishing the gaps etc. all complete as directed by Engineer-in Charge. v) Fixing Vitreous China under / over the counter / semi recessed type Wash Basin of following model and make conforming to IS 2556 and placing it in position with the granite platform as shown in the drawing or as directed including finishing the joints with white cement all complete. vi) Testing the system to the full satisfaction of the Engineer in Charge. Vitreous China Wash Hand Basin of StarWhite colour of 'Hindware Cat. No. 10036 "Windsor" model or Cera Cat. 'No. S2040102 "Canon" model or Parryware Cat. No. 'C8865 "Sunny" model, under counter model.

Providing braided hose with nuts, nipples etc. for Water supply Inlet connection of following make for wash basin, flush tank, kitchen sink etc with brass check nuts on both ends and fixing it in position as directed including the cost of jointing materials and testing for leak proof joints all complete. 450 mm long Braided hose of Jaquar cat. No. 805B or equivalent in equivalent in Roca/Toto.

Providing & fixing in position best quality bevelled edge plate Glass Mirror with PVC frame of following size with 6 mm thick marine ply wood (confirming to IS 710 : 2010) , fixed with required numbers of SS cup screws and caps, washers etc. including drilling holes, providing & fixing rawl plug in RCC/ brick wall, wooden packing behind the mirror if necessary, reinstating the damages to its original condition etc. all complete as directed by EIC. 6 mm thick Plate glass Mirror of size 600 mm x 450 mm / of required size with 6 mm thick marine ply wood (confirming to IS 710 : 2010) backing & PVC moulded frame of approved shade or as directed by the E.I.C

Providing & fixing in position following approved quality CP fittings / Fixtures of 15 mm nominal dia. with ISI mark / approved make of following type including providing & fixing specials, wall flanges and fixing to concealed / exposed pipe line with leak proof threaded joints using tephlon tapes, testing the joints hydraulically to a pressure of 10 kg./ sq.cm, rectifying the leaky joints. if any, including cleaning etc. complete all as per specification. C.P brass BIB Tap with wall flange, 'Florentine ' of jaquar cat. No.FLR-5047N or approved equivalent of Roca/ Toto make.

C.P brass 2 Way Bib Cock with wall flange of jaquar Florentine' Cat.No.FLR-5041 N or approved equivalent of Roca/ Toto make.

CP brass Wall Mixer with provision of Bath & Overhead Shower complete with Bend Pipe and wall flange of Jaquar Cat. No. FLR-5273UPR

CP brass Shower and Arm with wall flange of Jaquar Cat. No. OHS-1789 and SHA- 477.

C.P brass wash basin mixer single lever of FLORENTINE' of 'Jaquar' cat. No.FLR-5001B or approved equivalent of Roca/ Toto make

C.P brass Angular Stop Cock with wall flange of jaquar Florentine' Cat. No. FLR-5053 N or approved equivalent of Roca/ Toto make.

C.P. Health Faucet with 8 mm dia 1.2 m long flexible tube & Wall Hook of Jaquar Brand 'Allied' Cat. No. ALD-573 or approved equivalent of Roca/ Toto make

C.P. brass Sink Cock with wall flange of Jaquar Florentine' Cat. No. FLR-5309ND/FLR-5319NB or approved equivalent of Roca/ Toto make

Providing and fixing the following C.P Brass Bathroom / toilet accessories of following make and fixing on the wall using SS screws, rawl plugs etc. as per manufacturer's requirement all complete at the locations shown and as directed by the E-in-C. C.P. Brass Toilet paper Roll Holder of Jaquar Continental' Cat. No. ACN -1153S or approved equivalent of Roca/ Toto make.

CP brass Soap Dish Holder of Jaquar Cat. No. ACN-1131N or approved equivalent of Roca/ Toto make

CP brass Soap Dispenser with Glass Bottle of Jaquar Cat. No. ACN-1135N or approved equivalent of Roca/ Toto make

CP brass single Towel Rail of Jaquar 'Continental' Cat. No. ACN - 1111 SM or approved equivalent of Roca/ Toto make

C.P brass double coat hook as per 'Continental', Jaquar make Cat. No. ACN -1161N or approved equivalent of Roca/ Toto make

CP brass Corner Glass Shelf (with bracket) of Jaquar Cat. No. ACN-1173 or approved equivalent of Roca/ Toto make.

Supplying Stainless steel Sink of following size with or without Drain board, approved make, moulded out of 19 SWG (1 mm ) stainless steel sheet of grade AISI 304 (18/8) with waste coupling conforming to IS 13983, placing and fixing the Sink in position to correct line and level with basket type choke-stop strainer ( waste coupling ), Check nuts etc. including the cost of jointing materials, finishing the edges with white / matching colour cement as per manufacturer's recommendation all complete as per specification and as directed by EIC. Stainless steel Sink 'Nirali- Grace Plain' Big without Drain board and with 'Satin' finish of overall size 535 x 460 mm ( Bowl size 470x395x215 mm )

Part-II- B : Water Supply System Supplying & fixing on Exposed surfaces the following sizes uv-stabilized Chlorinated Poly Vinyl Chloride (CPVC ) pipes & Fittings of specified class having thermal stability for both hot & cold water supply consisting following items of work:- i) Supplying CPVC pipes and all required CPVC plain and brass threaded fittings, SDR - 11 having thermal stability for hot & cold water supply of approved make conforming to IS 15778 with ISI mark for CPVC pipe having nominal size up to 50 mm and conforming to ASTM F 441 (IPS SERIES) Schedule 40 for CPVC pipe having nominal size 65 mm (2 ½”) and above. ii) Supplying & providing providing CPVC/GI flanges, any other required specials and other jointing materials for connecting the CPVC pipe lines with spool pieces of water tank and for connecting the CPVC pipe lines with any fittings & fixtures etc., of the water supply line iii) Laying and fixing the pipe and specials on exposed surfaces / underground, to correct line, level and plumb for water supply line, using metal straps ( On wall surfaces ) at 1.00 mtr. interval or as directed by the EIC. iv) Jointing the pipes and Specials using Solvent cement conforming to IS 15225 & Teflon tape ( For threaded joins ) of approved makes including cutting the pipe to required size, preparation of surfaces, necessary tools etc. all complete. v) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. vi)Testing the pipe line as per relevant code to a hydraulic pressure of 10 Kg / Sq.cm to assess leakages if any, rectifying the defect, retesting etc till water tightness of pipe line is ensured vii) CPVC pipes and fittings/specials shall be of same brand. i) Supplying CPVC pipes and all required CPVC plain and brass threaded fittings, SDR - 11 having thermal stability for hot & cold water supply of approved make conforming to IS 15778 with ISI mark for CPVC pipe having nominal size up to 50 mm and conforming to ASTM F 441 (IPS SERIES) Schedule 40 for CPVC pipe having nominal size 65 mm (2 ½”) and above. ii) Supplying & providing providing CPVC/GI flanges, any other required specials and other jointing materials for connecting the CPVC pipe lines with spool pieces of water tank and for connecting the CPVC pipe lines with any fittings & fixtures etc., of the water supply line iii) Laying and fixing the pipe and specials on exposed surfaces / underground, to correct line, level and plumb for water supply line, using metal straps ( On wall surfaces ) at 1.00 mtr. interval or as directed by the EIC. iv) Jointing the pipes and Specials using Solvent cement conforming to IS 15225 & Teflon tape ( For threaded joins ) of approved makes including cutting the pipe to required size, preparation of surfaces, necessary tools etc. all complete. v) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. vi)Testing the pipe line as per relevant code to a hydraulic pressure of 10 Kg / Sq.cm to assess leakages if any, rectifying the defect, retesting etc till water tightness of pipe line is ensured vii) CPVC pipes and fittings/specials shall be of same brand. Note: 1) The rate shall also include for cPVC pipe & specials required for making connections with the existing GI / CPVC/ PP-R pipe line laid by other agency. 2) All threaded joints shall be made with brass threaded fittings only. 3) Exposed pipe fixing arrangement include providing & fixing slotted G.I. section & U clamps bolts arrangement for grouping of pipe. Sloted section thickness should not be less than 2mm. Pipes and Fittings SDR-11 as per IS 15778 20 mm(¾") n.size

25 mm (1")n.size

32 mm (1¼")n.size

40 mm (1½")n.size

50 mm(2") n.size

65 mm(2½") n.size

80 mm(3") n.size

Supplying, fixing & concealing on wall / beams / columns etc. the following sizes UV- stabilised Chlorinated PolyVinyl Chloride (CPVC) Pipes & (male / female) brass threaded fittings Fittings of specified class having thermal suitable for both hot & cold water supply & suitable for fixing various fittings & fixtures such as taps, wall mixture, concealed stop cock, flush valves etc., consisting following items of work :- i) Supplying CPVC pipes and all required CPVC plain / and brass threaded fittings, SDR - 11 having thermal stability for hot & cold water supply of approved make conforming to IS 15778 with ISI mark for CPVC pipe having nominal size up to 50 mm and conforming to ASTM F 441 (IPS SERIES) Schedule 40 for CPVC pipe having nominal size 65 mm (2 ½”) and above. ii) Laying and concealing the pipe and specials for water supply by cutting / making 75 mm X 75 mm groove on the wall, fixing the pipe using metal straps wherever required and filling the groove with cement mortar mixed with water proofing compound, after laying and testing the pipe line including making leak proof joints using cement solvent / Teflon tape ( For threaded fittings) of approved make, cutting the pipe to required length, preparation of surface, necessary tools etc. all complete, iii) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. iv) Testing the pipe line as per relevant code to a hydraulic pressure of 10 Kg / Sq.cm to assess leakages if any, rectifying the defect, retesting etc till water tightness of pipe line is ensured v) CPVC pipes and fittings/specials shall be of same brand. NOTE:- 1) The rate shall also include for cPVC pipe & specials required for making connections with the existing GI / PP-R/ CPVC pipe line laid by other agency. 2) All threaded joints shall be made with brass threaded fittings only. 3) All concealed cPVC pipes provided for PH work shall be measured under this item Pipes and Fittings SDR-11 as per IS 15778 20 mm(¾") n.size

25 mm (1")n.size

Supplying and laying below the ground or floor, the following diameter uv-stabilized Chlorinated Poly Vinyl Chloride (C-PVC) pipe line of specified class, consisting the following items of work:- i) Supplying CPVC pipes and all required CPVC plain / brass threaded fittings, SDR - 11 having thermal stability for hot & cold water supply of approved make conforming to IS 15778 with ISI mark for CPVC pipe having nominal size up to 50 mm and conforming to ASTM F 441 (IPS SERIES) Schedule 40 for CPVC pipe having nominal size 65 mm (2 ½”) and above. ii) Laying and fixing the pipe and specials below the ground or floor to correct line, level and plumb for water supply line. iii) Making leak proof threaded/welded joints. including cutting the pipe, cleaning, marking, jointing, etc. and including the cost of jointing materials. iv) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. v) Providing and fixing C-PVC weldable / threaded fittings such as Union, Nipples, Bends, Elbows, Tees, Reducers, End caps, Couplers, Adaptors, Saddles, Plugs, Tank connectors, Expansion loops, Bypass bends, etc vi) CPVC pipes and fittings shall be of same brand. vii) Testing the pipe line as per relevant code to a hydraulic pressure of 10 Kg / Sq.cm to assess leakages if any, rectifying the defect, retesting etc till water tightness of pipe line is ensured. NOTE:- 1) The rate shall also include for cPVC pipe & specials required for making connections with the existing GI pipe line laid by other agency. 2) All threaded joints shall be made with brass threaded fittings Only. 50 mm(2") n.size

Providing, instaling, fixing, connecting, testing 75 micron Super Flow Filter, of M/s. Jain Irrigation Systems Ltd. or approved equivalent, of following Model Nos, fitted with pressure gauge, water drain and emptying plug. etc all as per specifications, drawings and as directed by EIC. DJPSFP40SW, Max. working pressure = 10 kg/cm², Flow rate = 40 m³/hr, Inlet/Outlet Connection = 2 1/2"

DJPSFP50SW, Max. working pressure = 10 kg/cm², Flow rate = 50 m³/hr, Inlet/Outlet Connection = 3". NOTE: 1. Threaded fittings of pipe shall be of Brass Threaded only which will be measured and paid under relevant item. 2. All Super Flow Plus filter provided for PH work will be measured under this item

Providing and Fixing Ball Valve as per relevant IS suitable for pipe pressure class with body of bronze and ball & stem of Stainless Steel of approved make with fittings & material for conectivity and labour, making water proof joints, including cost of jointing material and CPVC specials if required & testing the joints. etc complete as per directions of engineer-in-charge. 20 mm(¾") n.size

25 mm (1")n.size

32 mm (1¼")n.size

40 mm (1½")n.size

50 mm (2") n.size

65 mm (2½") n.size

80 mm (3") n.size NOTE: 1) Item Includes Flange jointing with required new flanges and hardware . 2) Wherever required union joint shall be provided in pipe to facilitate removal of valve. 3) Threaded fittings of CPVC shall be of Brass Threaded only. Brass threaded CPVC fittings will be measured and paid under relavent item 4) All bronze ball valves provided for PH work will be measured under this item

Providing high pressure "HP" following size Float Valve assembly (horizontal plunger type ) conforming to IS 1703 with brass or gun metal piston, back nut and PVC float conforming to IS 9762, fixing to inlet pipe of water tank and making water proof joints including the cost of jointing materials and CPVC/ G.I specials, if required, testing the joints as per I.S. recommendations all complete as per specification and as directed. 50 mm dia.

Supplying & fixing following size C.P brass Coupling with approved quality C.P brass Mosquito proof jalli including providing CPVC/ GI connector, bend and any other CPVC/ GI specials, if required for fixing the coupling, jointing materials such as tefflon tapes, spun yarn, white zinc, fixing the same to GI/CPVC pipes etc. complete as specified & directed for overflow / vent pipe of water tank. 50 mm dia.

Supplying & fixing following Stainless Steel (grade 316) spool pieces of required diameter having flange on one / both end with flange holes in flanges for fixing with nut & bolts (OR) with screwed ends on both/ one end as per site requirement and as directed by the Engineer in charge , having 450 mm/ required length, providing 3D x 3D (where D is the outer diameter of pipe) and 4 mm thick stainless steel puddle plate (minimum size 150mm x 150mm) welded to it including cutting the plate to required shape and fixing in the reinforcement at the center of RCC wall / slab at required level, height etc including cutting the form work provided for casting concrete etc., Complete all as per specifications and as directed by Engineer-in-Charge. Note:- Actual weight of spool piece only will be measured for payment and no payment will be made for any wastages. 40 mm to 150 mm dia

Construction of brick masonry valve chambers of following dimensions for depth as mentioned below comprising of 230 mm thick brick masonry in cement mortar 1:4 over a bed of 150 mm thick cement concrete of grade 1:2:4 for foundation with 150 mm offset all round, including racking out joints & plastering in cement mortar 1:3, 20 mm thick both on internal and external surfaces, internal surfaces finished smooth with a floating coat of neat cement, Fixing (FRP/GRP) Frame and cover of approved make all as per specifications and directions of the E.I.C. including dewatering the pit, if required till completion of the work all complete. Chamber measuring 0.6 mtr. X 0.6 mtr. for an initial depth of 600 mm (Clear internal dimension)

Extra over above item for additional depth of valve chamber beyond initial depth of 0.60 mtr. for Valve Chamber without steps / foot rests / rungs etc. all complete. NOTE:- Providing and fixing composite frame & cover will be paid under relevant item.

Providing GRP/FRP composite Mosquito proof hinged cover with frame for Overhead Water Tank (Having loading capacity not less than 300 Kg) of 'EVERLAST' having suitable locking arrangement for Manhole opening of water tank, fixing the cover by providing corrosion resistant studs, nuts, built-in hold fasts etc. by chasing or cutting holes and grouting with cement mortar 1:1 by adding approved water proofing compound @ 2% by weight of cement, all complete as per specification and as directed by EIC. 530 mm dia. Total of Part II: - B

Part-II-C : Drainage System Supplying and fixing following size uPVC UV-Stabilised soil / waste quality pipes and fittings ( SWR ) for soil, waste, vent, anti syphonage, HVAC waste pipe and rain water pipe lines consisting following items of work:- i) Providing and fixing uPVC UV-Stabilised Soil / waste pipe as per IS:13592 and IS:14735 Type-B laid in floor & on Exposed faces of wall of approved make. ii) Fixing the pipeline vertically by Metal clamps with rubber seal of approved make. iii) Fixing the pipeline Horizontaly with specified slope below the ceiling by Metal clamps with rubber seal and GI hanger rods not less than 5mm dia at specified spacing, including all required hardware. iv) Providing and fixing uPVC cowl at the top of soil, waste water & vent pipe line. v) Providing and fixing uPVC P/S trap on line as per requirement for soil,waste water pipeline. vi) Laying the pipe below floor / ground to the slope and gradient equal to (or) steeper than 1 in 50, making leak proof connections of soil /waste pipe line from the shaft with inspection chamber / Manhole / Gully trap Chamber including the cost of filling around the holes of inspection chamber / Manhole / Gully trap with cement mortar 1:1 mixed with water proofing compound vii) Jointing the pipe / fittings with Solvent Cement & Rubber ring gasket with making holes in walls / floor grooving and redoing the same and brick support etc. Carrying out water-tightness test for the pipes laid as per codal provisions. Providing Ring Joint pipes at verticals and solvent cement jointed pipes at concealed locations. viii) Cutting the pipe to the required length including providing short pieces, necessary connectors, fittings & specials with & without door, assorted fittings such as plugs, tees, couplers, reducers, cross tees, reducing tees, elbows, bends, single & double Y, vent cowl, gaskets, offsets etc. Including providing necessary clean outs, cleaning pipe, extension pipe if any for clean outs, door bend, door elbow, door Y, socket plug, etc wherever required for accessing every segment of soil and waste pipes to enable removal of any Chock up after installation. ix) Providing necessary specials for connecting UPVC SWR (IS 13592/ IS 14735) pipe with UPVC (IS 4985) pipe etc x) Dewatering the pit/ trenches if necessary till completion of work xi) Testing the pipe line for any leakages, rectifying the leakages if any, retesting etc., till water tightness of the pipe line is ensured. xii)Exposed pipe fixing arrangement include slotted G.I. section and U clamps with rubber packing. Note: Earthwork excavation for trenches shall be paid under relevant items ) For Soil, waste, Vent & Rain water pipe lines 50 mm dia

75 mm dia.

110 mm dia.

Supplying, fixing & concealing on walls / beams / columns etc. the following sizes uPVC Pipes & Fittings of specified class consisting following items of work:- i) Supplying uPVC pipes conforming to IS 4985 and uPVC moulded plain / threaded fittings conforming to IS 7834 for waste water pipe line of approved make with ISI mark / equivalent approvals as per relevant standards, providing necessary specials for connecting UPVC (IS 4985) pipe with UPVC SWR (IS 13592) pipe etc. ii) Laying and concealing the pipe and specials for waste water by cutting / making 75 mm X 75 mm groove on the wall, fixing the pipe using metal straps wherever required and filling the groove with cement mortar 1:3 mixed with water proofing compound, after laying and testing the pipe line including making leak proof joints using cement solvent / Teflon tape ( For threaded fittings) of approved make, cutting the pipe to required length, preparation of surface, necessary tools etc. all complete iii) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition (No Chases in RCC wall, column, beam, slab, chajja,etc shall be made with out getting the getting the permission from Engineer In charge & structural design Engineer) iv) Concealing the pipes in wall, Laying the pipe below floor / ground to the slope and gradient equal to (or) steeper than 1 in 50 vii) Testing the pipe line for any leakages, rectifying the leakages if any, retesting etc., till water tightness of the pipe line is ensured . For Urinal/wash basin/ Anti syphonic/ Sink waste. (10kg Pressure) 50 mm dia.

Providing uPVC Floor Trap / Nahani Trap of following size having not less than 40 mm effective water seal, fixing the trap in position and connecting with waste water pipe by cement solvent / as per manufacturer's recommandation, embedding the trap in cement concrete 1:2:4 to correct level and gradient, providing and fixing 200 x 200 mm size top tile with central strainer & flat cover / flush strainer, closing the side inletes with plugs if required etc.complete all as per specification and as directed by the Engineer in charge. Multifloor trap of 110 x 75 x 50 size of approved make with 3 pc top tile & flush strainer, mat finish.

Providing and fixing HDPE sheet flashing fabricated by welding HDPE flexible sheet with 160 / 110 mm dia HDPE pipe about 400mm long for PVC rain water pipes, fixing the same on RCC/cement concrete surface using approved synthetic glue, covering the HDPE sheet wateright with cement mortar 1:2 mixed with water proofing compound and forming the proper shape and grade and finishing with inlet mouth of rain water pipe, cutting RCC slab or wall if required, including the cost of bitumen, cement mortar etc. complete all as per specification and as directed by the Engineer-in-charge. NOTE: HDPE sheet flashing shall be sticked watertight over RCC / Cement Concrete surface by using approved synthetic glue as per manufacturers recommendation and as directed by the Engineer incharge. After fixing HDPE sheet flashing over RCC/ Cement concrete surface, the top potion of HDPE sheet flashing shall be spread with approved synthetic glue, fine (0.5 mm size) sand shall be sprinkled over it immeadiately, allowed to be dried and after drying it is to be covered watertight with cement mortar1:2 mixed with waterproofing compound @ 2% by weight of cement as per required shape and form. Item includes providing 160x110 mm uPVC reducer and 110mm dia 150 mm length pipe piece. 450 x 450 mm size HDPE sheet Flashing fabricated from 8 mm thick HDPE sheet and PN 6 grade 160 mm/110 mm dia HDPE pipe

Providing and fixing Stainless steel Dome mesh fabricated by welding from 2mm dia 304 grade stainless steel wire for PVC rain water pipes (sheet flashings), with 5mm x 10mm L base ring of 0.5mm thickness 304 grade Stainless steel. L ring to be embedded in waterproofing & dome to be placed on it, including the cost of fixing material etc. all complete as specified and as directed by the E.I.C. Half Spherical Dome having opening 5 to 10 mm of 160 mm ID

Providing, jointing and fixing 'RAINY' online Filters, model as below on roof rain water downtake pipeline at suitable location including fixing the Filter Unit on the wall using suitable anchor bolts, brackets, nuts etc. as per manufacturer's requirement, testing etc. all complete. The cost shall include all accessories, specials etc. to commission the Filter. Item also includes Providing and Fixing 110mm dia uPVC Ball valve (white, off-white or grey colour, agri class) of Approved make suitable for pipe pressure class of approved make with material and labour, making water proof joints, including cost of jointing material and uPVC specials if required & testing the joints. etc. complete as per directions of engineer-in-charge. Rainy FL-200 with 110mm PN10 uPVC ball valve & reducer

Constructing brick masonry Gully Trap chamber of following size and upto 600 mm initial depth including providing and fixing gully trap, consisting following items of work:- i) Providing square mouth uPVC gully trap of size 150 X 150 mm with 110 mm outlet of approved make embedding in position in cement concrete 1:2:4 inside the chamber. ii) 230 mm thick brick masonry in 1:4 cement mortar over 150 mm thick cement concrete 1:2:4. iii) 15 mm thick plaster in cement mortar 1:3 on internal and external surfaces, internal surfaces and top finished with a floating coat of neat cement. iv) Providing and fixing precast EVERLAST or approved equivalent Composite (FRP/GRP) Manhole covers & frame of size 300mm x 300mm as approved by E.I.C having point loading capacity not less than 0.3 tonne with name of department and year engraved as specified / approved, including cost of necessary hardware and cement concrete / mortar for fixing the frame. as specified and as directed by the E.I.C. 300 X 300 mm size Gully Trap chamber.

Providing & laying UPVC under ground drainage pipes & Fittings of approved make for storm water drains & Sewer lines of following size conforming to IS:15328 to proper level & grade, jointing including providing coupler with cement solvent / welded joints / as per manufacturer's requirement, encasing the pipe alround using cement concrete 1:3:6 complete all as per specifictions, drawing and as directed by the E.I.C. Item includes Providing and fixing UPVC fittings such as Bendes, Tees & Y, Reducers, Blanking Plugs, Couplers, Adaptors etc Note:- Cement Concrete for encasing will be paid under different relevent item. 110 mm DN (SN 8kN/m²-SDR34)

160 mm DN (SN 8kN/m²-SDR34)

Providing, fabricating and fixing uPVC Sewer trap of size mentioned below which consist of fabricating uPVC sewer trap as per drawing, by using 3 Numbers of 90 degree bends of Underground drainage quality uPVC pipe SWR bend / Sky rise SWR bends of approved make , including placing and fixing sewer trap in position inside the manhole / inspection chamber, embedding in cement concrete of grade 1:2:4 to the required line, level slope as per drawing , providing 1 Number of single Y(UPVC water supply fitting No MP6WYE200L (or) equivalent), 200/110 SWR/ Sky rise SWR/ UPVC reducer, providing and fixing SWR 110 mm dia cleaning pipe with blank plug/ end cap, providing and fixing 110 mmm dia SWR vent pipe with cowl as per drawing, finishing the joints and rectifying the leakages if any after test etc.complete all as per specifications, Drawing & as directed by the Engineer-in- Charge. Note:- The cost of providing & fixing 110 mm dia SWR cleaning pipe and vent pipe will be paid under relevent different item. 160 mm dia

NOTE FOR INSPECTION CHAMBER & MANHOLE i) Depth of Inspection chamber shall be the vertical distance from the top of the frame & cover of manhole / chamber to the outgoing invert of the main drain channel. ii) The internal diameter / sizes of inspection chambers & manholes mentioned in the item shall be measured from finished plastered surfaces. iii) The cost of 1:2:4 grade concrete and plastering with CM 1:2 for fixing frame & cover is included under the scope of work of item for providing Everlast Cover. iv) Slope of 1:6 for benching shall be started from channel of depth equal of the outgoing sewer diameter. v) The slope of conical wall of manhole and longitudinal walls of rectangular Inspection Chamber starts from the vertical height of 200mm from top of frame and cover. vi) While making payment for extra over initial depth, the thickness of RCC frame & cover and the thickness of cement concrete bed block (bearing course) shall not be deducted from the depth of manhole or chamber. Constructing brick masonry Inspection chambers of internal sizes 900 X 600mm at bottom and 900 X 450mm at top for an initial depth of 600mm consisting following items of work. i) 230 mm thick brick masonry in cement mortar 1:2 over 150 mm thick bed in cement concrete of grade 1:2:4 with 150 mm offset all-around, tapering of longitudinal walls starting from the height of 450 mm from the top of chamber frame & cover and tapering of longitudinal walls ending at the height of 200 mm from the top of frame & Cover to obtain an internal dimensionof 900 X 450mm at 200 mm from top of chamber. ii) 20 mm thick plaster in cement mortar 1:1 mixed with water proofing compound @ 2% by weight of cement on internal and external surfaces, internal surfaces and top finished with a floating coat of neat cement. iii) Making benching and haunching in cement concrete of grade 1:2:4 and finishing with floating coat of neat cement. iv) Fixing frame and cover at top using cement concrete of grade 1:2:4 (for bed block / bearing course and capping) and cast iron steps / foot rests, all as per specification and as directed by E-in-C. NOTE:- Providing & fixing foot-rests / steps and CI / RCC / composite frame & cover including CC of grade 1:2:4 & C.M 1:2 plaster for fixing the frame and cover, will be paid under relevant item/ included in other relevant Inspection chamber of internal sizes 900 X 600 mm at bottom and 900 X 450 mm at top for an initial depth of 600 mm.

Extra over above item for additional depth of inspection chamber beyond 600 mm initial depth & upto a depth of 1800 mm. all as per specification and as directed. Note:- additional depth of chamber will be measured in cm and paid as per actual depth.

Providing & fixing precast approved brand (EVERLAST) Composite Manhole covers as approved by Competant authority / E.I.C tested as per IS:1726, including cost of necessary hardware, 1:2:4 grade concrete for fixing frame, bed block (bearing course) and capping including necessary form work and CM 1:2 mortar for fixing the frame & for plastering exposed surfaces of concrete bed block (bearing course) and capping finished smooth with floating coat of neat cement etc., complete as per specifications, drawings and as directed by the E.I.C. Rectangular Heavy duty (Grade HD - 20 designation as per IS:1726) frame and cover size 910 x 450mm

Square Heavy duty (Grade HD - 20 designation as per IS:1726) frame and cover size 600 x 600mm for Valve Chambers Note: Shade and Colour and design pattern to be get approved from Engineer-in-Charge.

Making drop connection for initial depth difference between incoming and outgoing sewer line upto 600mm including making ramp, U-channel of height and width not less than branch pipe dia in CC 1:2:4, plastering 20mm thick in CM 1:3, finished smooth with a floating coat of net cement. and for drop connection having depth differance between incoming and outgoing sewer line more than 600mm including providing and laying following dia. uPVC pipe conforming to IS:15328 & specials, providing and fixing bends, tees, crosses, plugs, caps etc., jointing the pipes/fittings using sealant of approved manufacturer, encasing the pipes with CC 1:3:6 such that shape of the cross section through encased pipe shall be square and sides equal to outer diameter of pipe plus 300mm, including form work, curing etc., all as shown in the drawing, as mentioned in the specifications and as directed by EIC. a) for initial depth difference of 600mm

b) for depth difference more than 600mm 160 mm DN (SN 8kN/m²-SDR34) NOTE:- 1) The depth of drop connection shall be measured vertically from the bed level of drop pipe cleaning chamber to the invert of manhole or chamber. 2) CC and form work for encasing will be measured and paid under relevant item. 3) uPVC pipe and fittings, specials will be measured and paid under relevant item.

Construction of brick masonry drop pipe cleaning chamber of internal size 300 x 300 / 450 x 450 mm for depth of 450 mm from top of cover & frame above uPVC drop pipe in brick masonry, in cement mortar 1:2 and 230 mm thick wall over 150 mm offset from all outer finished wall surfaces of the chamber, providing & fixing suitable medium / heavy duty pre-cast FRP cover of approved (EVERLAST) make, CC 1:2:4 coping at top of brick work, 20 mm cement plastering in cement mortar 1:1, mixed with water proofing compound @ 2% by weight of cement in internal & external surfaces of the chamber, all inside surfaces finishing smooth with floating coat of neat cement and external surfaces finishing rough with wooden float, including dewatering if necessary till completion of the work, all as directed by the E.I.C. 300 x 300 mm chamber with HD-20 FRP composite cover and frame for pipes upto 250 mm pipe

Providing copolymer polypropylene steel reinforced plastic Foot-rests / Steps of Patel brand or eq. as per ASTM D - 4101 specification and moulded a 12 mm dia. IS - 1786 grade Fe - 415 steel reinforcing bar and in "U" shape having dimensions 263 x 168 mm and fixing in concrete / wall as shown in the drawing and as directed all complete. Note: All Foot-rests provided for PH work will be measured under this item.

Part-II-D : Rain Water Harvesting System Boring/Drilling bore well of required dia.for casing / strainer pipe by suitable method prescribed in IS: 2800 (Part-1), including collecting soil samples from different strata, preparing & submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machinaries required for the job, all complete as per the direction of Engineer- in- Charge, Upto 30 mtr. depth below ground level. All types of soil, 300 mm dia

Rocky strata including boulders, 300 mm dia

Providing, fixing, laying, jointing & testing below the ground / above ground UPVC socketed pipes for solvent cement joint / plain ended CLASS 5 pipes as per IS:4985 including suitable heavy fittings like elbows, collars, tees, unions, couplings, reducers, bends, enlargers, saddles flanged tailpieces and all other fittings required for the completion of laying and jointing as per IS 7634, testing pipelines with fittings for 10 kg/cm2 hydrostatic pressure for minimum duration of two hours with clean water and rectifying the leaks if found, cutting the pipes to the size, threading as required, jointing of pipes and fittings to be carried out using Hold-ties, Teflon tape, PVC clamps, wooden gutties, SS screws, cement, solvent cement etc. required for the completion of the work and all as per specifications, drawings and direction of the Engineer-in-charge. normal 110 mm dia class 5 perforated pipe

Gravel packing in tube well construction ( Around casing pipe ) in accordance with IS:4097, including providing gravel fine/medium/course, in required grading & sizes as per actual requirement, all complete as per direction of EIC.

Providing & fixing in position following size Weep holes wherever required in RCC / Masonry walls including cutting to required shape & size all as per specifications, drawings & as directed by the E.I.C all complete. PVC pipe of 75 mm OD (IS:4985-6Kg class)

Providing and fixing recharge well screen ( two cylindrical V-wire screens fitted concentric to each other. Annular spaces filled with graded gravel) assembly of M/s Appollo screens or equivalent aproved manufacturers, including hardware and labourer as per drawing and specified by E I C. size of screen 8-16 1.00 m length(material SS 304)

Supplying, fabricating and fixing in position structural steel of angle, joists, channel, I Beam, plain / chequered plates for monorail / MS gates / supports of required size including cutting, fabricating, welding, erecting in position including supplying & fixing embedded parts for fixing monorail / supports in concrete, including painting with two coats of approved synthetic enamel paint over a coat of zinc cromate red oxide primer all complete all as per specification and as directed by the Engineer in Charge Structural steel using MS flats, Angles. Rods etc etc.

Section - I: LT CABLES & END JOINTS : L.T Cables: Supply, installation, testing & commissioning of 1.1 KVgrade aluminium/ Cu stranded circular/ sector shape core conductor with XLPE insulation, extruded PVC inner sheathed, G.I flat strip/wire armoured, extruded FRLS grade antirodent & anti termite PVC (ST-2)outer sheathed cable conforming to IS : 1554 Part I / IS 7098 Part-I with latest amendments, fixed on wall/column/slab/ false ceiling / existing cable tray /existing hume pipe/trench/shaft/pit/ on 5mm thick M.S. flat /GI spacer/angle/support fixed with coach screws/grouted in wall/anchor fasteners 2mm. thick G.I. fabricated saddle, all fixing accessories, etc complete including painting of M.S spacers/angles and saddles or in ground , sand bedding,laying of baked bricks on side & top-, temporary reinstatement, back filling, dewatering, consolidation,disposal of excess earth within the radius of 500 m and making good to the original finish etc providing Al cable tag as per enclosed detailed specifications, drawings & asper instructions of the E-I-C & of the following sizes. NOTE:1) Excavation of earth shall be measured under Miscellaneous item. 2) Sealing of hume pipes with wooden bushes aftercable laying shall be included in the scope of work. 3) Clamping of cables on trays including supply of clamping materials as per instruction of EIC shall beincluded in the scope of work. 3.5C x 95 Sq.mm Al. conductor cable

4C x 35 Sq.mm Al. conductor cable

4C x 16 Sq.mm Al. conductor cable

LT Cables End Joints End jointing of following sizes of cable by crimping with supply of all jointing materials like solderless tinnedcopper cable socket,double compression brass cable glands, gland earthing, insulation tape, flux, duplicate interconnection between gland earthing strip & to the nearest earthing bus terminals as per the drawings,specifications and as per the instructions of the Engineer-in-charge. 3.5C x 95 Sq.mm Al. conductor cable

4C x 35 Sq.mm Al. conductor cable

4C x 16 Sq.mm Al. conductor cable

Section-II: Readymade Distribution Board : Supply, installation, testing & commissioning of following readymade distribution boards, double door, IP 42 degree protection complete with necessary, MCB isolators , MCBs,earth leakage circuit breaker (ELCB) etc including interconnections with appropriate capacity size of PVC insulated copper conductor wires (ISI marked),suitable for concealed mounting /wall mounting with MS frame workof 40 x 40 x 5 mm MS angle iron, with M.S. enclosure fabricated out of min 18 SWG /20 SWG thick M.S. CRCA sheet as per manufacturers standard, with concealed hinged door, locking arrangement etc. including earthing clamps for both incoming & outgoing circuits,interconnections, per phase isolation kit as required,cable end box & wire way box if required, continuous copper earth wire in the wire way box with single/duplicate brass earthing terminals, danger board, name plate, flexible earthing for the door, metal treatment & powder coatedpainting, Phase Distribution drawing etc. all as per drawings (G.A. & fabrication drawing to be got approved), Note: 1.MCBs (Type –C) shall be minimum 10 KA breaking capacity, as specified. 2. MCCB shall be thermal magnetic with 35KA minimum breaking capacity. 3. Blanking Plates shall be included in scope of work. 4. DB shall be of standard readymade type from approved manufacturers as indicated in preferred makes of material. VTPN MDB (Normal Supply) : a) 250 A , FP MCCB - 1 No. b) 125 ,TP MCB - 5 Nos. c) 63 A TP MCB - 4 Nos d) 12 way brass neutral link - 2 set

VTPN MDB (Emergency Supply) : a) 125 A , FP MCCB - 1 No. b) 63/40 A ,TP MCB -10 Nos. c) 25A DP MCB - 2 Nos d) 12 way brass neutral link - 2 set

VTPN MDB (In Each Floor) : a) 160 A , FP MCCB -1 No. b) 40/63A ,TP MCB -12 Nos. c)12 way brass neutral link - 2 set

SP DB : (For Rooms) a) 40A DP, 30mA RCBO - 1 No. b) 40 A DP Contactor c) 6-32A SP MCB - 12 nos d) 8 way brass neutral link - 2 set

SP DB : (For common areas) a) 40A DP, 30mA RCBO - 1 No. b) 6-32A SP MCB - 8 nos c) 8 way brass neutral link -- 2 set

MCCB/ MCB enclosure: Supply, Installation, Testing & Commissioning of following MCCB/ MCB with suitable IP 42, MS CRCA powder coated enclosure with angle iron framework including minor civil worksto fix on the wall etc complete and all ncessary and as directed by EIC 63A, 25 kA FP MCB with 63A FP, 300mA ELCB (for lift machine)

25A DP MCB with 25A, 30 mA ELCB for (lift car & lift shaft Lighting)

Flexi-DB with acrylic door : a) 63 A FP MCB -- 1 no. b) 63A, 4P, 4 NO Power contactor -- 1 no c) Auto/Manual switch with centre off - 1 no. d) On/Off push button - 1 no. e) Digital time switch with one channel -1 No. f) 25A DP MCB (D-Curve) -- 6 nos. TOTAL COST OF READYMADE DB WORKS

Section-III: Point wiring and Submain wiring Point wiring in PVC (HMS variety) conduits : Point wiring for light/ceiing fan/6A/ 16A/ socket outlet/6A outlet for exhaust fan , bell point etc. with 1.1 KV grade FRLS PVC insulated multistranded copper conductor wire (ISI marked), in existing floor raceway/ including providing and fixing of 25 to 40 mm dia High mechanical stress (HMS) rigid PVC conduit having ISI marked IS 9537 Part - 3, including fixing accessories & hardware concealed /exposed in slab/wall or on 5mm.thick G.I. spacers fixed with no. 10 nettle fold wood screws with nylon plug complete with all conduit accessories 0.9mm G.I. Saddles, ready made MS switch boxes & socket outlet boxes of nominal 1.2 mm thickness , brass earthing stud 1/2 nos, controlling modular switches, sockets with moulded front plate and inner plate etc. including appropriate size of FRLS PVC insulated copper earth wire ,brass/bakelite (straight / angular) lamp holders, 3 plate ceiling rose,6 A, connectors, painting etc. as per specifications and drawings and as per instructions of E-I-C and as detailed below : (sample switch Box etc. to begot approved before fabrication) NOTE: 1. Connections shall be done with crimped type tinned copper lugs & washers. 2. All switches & socket outlets shall be as per preferred makes. 3. All sample boxes with accessories /luminaires shall begot approved from Department. 4. All 16 A socket outlets should be with 6 pin type 5. MS boxes other than switch boxes & socket outlet boxes shall be fabricated out of minimum 1.5mm thick MS sheet duly painted with red oxide primer & 2 coats of epoxy paint. 6. Minimum size of the FRLS insulated copper earth continuity wire shall be 2.5 sq.mm. 7. The colour shade of switches shall be white /off white. For socket outlet points/switch boards on normal power supply, the cover plate shall be white/off white colour, graphite grey (RAL 7024) or other shade as per instruction of EIC, for socket outlet points/switch boards on DG power supply. For Common Area & Stilt Area Primary Light point with 2 nos. 1.5 sq.mm wires & 1 No. 2.5 sqmm earth wire with 6A switch On DG power supply

Secondary light point with 2 nos of 1.5 sq.mm wires alongwith 1 no of 2.5 sq.mm insulated earth wire looped to above item 1.1.1 ON DG power supply

Primary Light point with 2 nos. 1.5 sq.mm wires & 1 No. 2.5 sqmm earth wire with 'Two way' 6A switch (Staircaselights) on DG supply

Secondary light point with 2 nos of 1.5 sq.mm wires alongwith 1 no of 2.5 sq.mm insulated earth wire looped to above item 1.3 (Staircase lights) on DG supply

Primary Light point with 2 nos. 1.5 sq.mm wires & 1 No. 2.5 sqmm earth wire directly controlled from DB (Entrance lights) on DG supply

Secondary light point with 2 nos of 1.5 sq.mm wires alongwith 1 no of 2.5 sq.mm insulated earth wire looped to above item 1.5 (Entrance Lights) on DG supply

Primary Light point with 2 nos. 2.5 sq.mm wires & 1 No. 2.5 sqmm earth wire directly controlled from DB (Area lights) on DG supply

16 A 6 pin socket outlet point with 2.5 sq.mm wires alongwith 1 no of 2.5 sq.mm insulated earth wire completewith 16 A switch in one box On DG supply

6A socket point with 2 nos of 1.5 sq.mm wires alongwith 1 no of 2.5 sq.mm insulated earth wires & 6A switch On DG supply

In Lift Shafts : Primary point in lift shaft with 2 nos of 2.5 sq.mm wires alongwith 1 No. of 2.5 sq.mm insulated earth wire with 600 lumen output LED bulk head luminaire with 6 A SP controlling switch and 16 A, 6 pin socket with 16 A SP controlling switch all in one box including all fixing material etc & as directed by E-I-C.

Secondary pts with 2.5 sq.mm wires same as item no. 1.3.2 above also looping is done from Item No.1.3.2 above & as directed by E-I-C alongwith 1 noof 2.5 sq.mm insulated earth wires & 6A switch

Point wiring with 2 nos. 4 sq.mm wire and 1 no. 2.5 sq.mm insulated earth wire complete with 20A 3pin socket outlet with plug &20 A DP MCB in readymade powder coated MS CRCA box with MS cover, located in lift shaft, as per instructions of EIC. MCB shall be with 10 KA breaking capacity.

For Guest Rooms: Point wiring for key fob switch with 2 nos of 1.5 sq.mm insulated wires & key fob switch with integrated time delay supplied alongwith key fob complete with label holder etc. On Normal power supply

Primary Light point with 2 nos. 1.5 sq.mm wires & 1 No. 2.5 sqmm earth wire with 6A switch On Normal power supply

Ceiling fan points with 1.5 sq.mm wires and with 2.5 sq.mm insulated earth wire complete with 6A,240V, two way controlled switches & 5 stepped capacitor type regulator On Normal power supply

6A socket point with 2 nos of 1.5 sq.mm wires alongwith 1 no of 2.5 sq.mm insulated earth wires & 6A switch On Normal Power supply

Call bell point with 1.5 sq.mm phase wires & 2.5 sqmm earth wire, with 6A bell push housed in MS box and approved make bul bul type bell with step down transfomer in polycarbonate enclosure. On Normal Power supply

Point wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper wire in surface/recessed PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 2.5 sq. mm. FRLS PVC insulated copper conductor single core cable etc as required. On Normal Power supply

3 nos.6A/10A/13A multistandard socket points with 2 nos of 2.5 sq.mm wires alongwith 1 no of 2.5 sq.mm insulated earth wires, looping with 1.5 sqmm + 2.5 sqmm wires (for earth) & independent 13A switches on existing Junction Boxes On Normal Power supply

Point wiring with 4 sq.mm wire and 2.5 sq.mm insulated earth wire complete with 25 A 3pin socket outlet with plug(Industrial Type) near split AC unit & 25A DP MCB at operating height on wall, in readymade powder coated MS CRCA box with MS cover and with necessary cutouts,interconnections earthing stud etc . MCB shall be with 10KA breaking capacity. On Normal Power supply

16 A 6 pin socket outlet point with 2.5 sq.mm wires alongwith 1 no of 2.5 sq.mm insulated earth wire completewith 16 A switch in one box On Normal Power supply

Water heater point with 4 sq.mm + 2.5 sq.mm insulated earth wires , 32 A DP MCB type isolator (non tripping type)in MS box near door at suitable position , 30A 3 way connector block mounted in MS box near heater On Normal Power supply

Point wiring for single phase exhaust fan with 1.5 sq.mm phase wires & 2.5 sqmm earth wire & with ceiling rose near exhaust fan & controlling 6 A , 240 V SP switch on nearest switchboard. On Normal Power supply

6A socket outlet point with 2 nos of 1.5 sq.mm wires alongwith 1 no of 2.5 sq.mm insulated earth wire complete with 6 A switch in switchboard (Board Point). On Normal Power supply

Submain Wiring : Supply, installation testing & commissioning of 1100 VFRLS grade PVC insulated multistranded Copper conductor Flexible wires of the following sizes with necessary lead sat both sides including Providing and fixing of 25mm/ 32mm/ 40mm dia PVC(HMS)or MS conduit concealed in wall/beam/ slab/column or onsurface of wall/beam/slab/ column on 5 mm thick G.Ispacer and 20 SWG GI saddle, MS pull out boxes , junction boxes of suitable sizes as per site requirement, from MDB to individual DB including connection with copper lugs etcas per specifications and as per the instruction of Engineer-in-charge. Note: 1. Connections shall be done with crimped type tinned copper lugs. 2. All embeded conduit junction boxes/pull boxes shall be covered by 18 SWG thick M S sheet covers painted white projecting atleast 5 mm around finished opening fixed tobox with CSK machine screws. 2 nos. of 10 sq.mm & 1 no of 6 sq mm copper wire including Providing and fixing of 32 mm dia PVC conduit (HMS variety) with necessary pull out boxes, junction boxes etc including end temination at both the ends with additional loop wire of 0.5 m length at either ends. TOTAL COST OF POINT WIRING AND SUBMAIN WIRING WORKS

Section -IV: MAINTENANCE FREE EARTHING SYSTEM Supply,installation,testing & commissioning of maintenance free earthing system & associated works, etc.complete as per specifications & instructions of E-I-C. NOTE:1) Measurement of Earth resistance must be carried out as per instructions of EIC. 2) All type of excavation shall be measured under relevant item no.of Miscellaneous item. Providing and making earth station comprising of 17 mm dia 3m long earthing electrode of high tensile low carbon steel rod molecularly bonded 250 micron copper coating on the outer surface, UL listed, filling bore with suitable earth enhancement compound as per IEC 62561-7 & manufacturer's standard, surrounding the earth electrode complete with all required materials & instructions of EIC.(Body-4, LPS-20) Note: The scope includes :- 1) Installation of earth rods including making pit/ drilling rock as per manufacturer's recommendations & design. 2) Exothermic welding of joints between earth electrode & GI / tinned Cu strip and between GI / tinned Cu strips,used for interconnection of earth electrodes. 3) Each earth electrode shall be provided with poly plastic inspection chamber with cover as per OEM standard.

Supply & installation of 50x6mm & 150 mm long tinned Cu equipotential bar inside concrete chamber (600 x 600 x600 mm) as per instructions of EIC. Note:1) The date of testing and earth resistance value shall be written on the cover with black base with yellow paint. 2) The concrete chamber shall be included in Civil relevent item

Supply & installation of discharge gap device with parallel connected surge voltage protector to couple different earthing system similar to M/S OBO make FS-V20 or equivalent in fibre glass reinforced polyester enclosure IP65 & IK08 of size 200 (H) x 250 (W) x 115 (D) mm similarto M/s Spelsberg cat no. Abox-i 250. 1) The enclosure housing discharge gap device shall be installed in concrete chamber housing equipotential bar. 2) The scope includes interconnection of equipotential bars of lightning & body earthing with suitable size flexible Cu conductor with bimetallic lug at one end as per site & instructions of EIC.

G.I / tinned Cu earth wire/earth strip fixed on wall/side of trench/slab /column /beam/ shaft connection to panel/DBs/SFU's etc. with 5mm thick G.I. Spacers & 2mm thick G.I. Saddle or in ground at 500 mm below with earth enhancing material surrounding the strip, including excavation in ground, refilling & removal of excess earth within a radius of 500 m, temporary instatement & backfilling of trench, consolidation, painting with two coats of black bituminous paint for earth wire/ strip in ground & green enamel paint for earth wire /strip on surface etc. 25 X 6 mm tinned copper strip

25 X 3 mm tinned copper strip

8 SWG tinned Cu earth wire TOTAL COST OF MAINTENANCE FREE EARTHING WORKS

Section -V: LAN SYSTEM LAN System : Supply, instalaltion, testing & commissioning of local area network system comprising of passive components like CAT-6A UTP or improved data cable, information oulet with RJ-45 connections , enclsoures for data outlets with faceplates concealed, patch panels, cable managers, LIU, OFC,splicing, 19" mounting racks , power panels in racks ,cooling fans in racks, flexible G.I pipe, including Providing and fixing of PVC conduit HMS variety conforming to IS 9537 Part-III etc., complete with labeling/identification on the cable , outlets, patch panels etc. complete in all respect as required as per standards,drawings, specifications and instructions of E-I-C. Note : 1. LAN work shall be done by a specialised agency in the field. Credentials of the agency through which the bidder proposes to execute the LAN work to be submitted post W.O. 2. Evaluation of the proposed agency to execute the LAN work shall be carried out seperately by the Department. 3. Active components i.e switches etc are not in the scope of the agency and shall be executed by the users seperately. Agency shall extend full co-operation to theagency / users executing the balance work which is not inthe scope of this tender. 4. Scope includes termination of cables at both ends with all accessories and installation/mounting of 19" racks with all accessories like angle iron frame work etc without any extra cost to the Department. 5. All LAN passive components shall be of same make. Point Wiring :(LAN,Wifi and CCTV points) Point wiring including Providing and fixing of MS/PVC conduit HMS variety of size 25-40 mm dia ISI mark concealed in slab/column/beam/surface wherever required complete with bends, T/ Cross, junction box with all accessories with RJ-45 shuttered socket outlets (modular) concealed / surface in wall/column/wherever required with all accessories including label holder, face plate, factory made zinc passivated box, screws etc terminated at one end at patch panel at respective floor at the other end in outlet with an extra loop length of approx 2 m at patch panel, ferrule numbers on both side,all terminations as per standards, drawing, specificationsand as per instructions of E-I-C Note : 1. Patch panel shall be measured seperately. 2. Colour of the outlet and facia plate shall be matching with electrical switches and sockets with the approval of E-I-C.

Patch Panels: Supply, installation , testing & commissiong of 24 port, 19"rackmountable patch panel equiped with RJ-45 receptive female, CAT-6A UTP or better compatible to cat-6A cable and cable managers complete as required as per instructions of E-I-C.

LAN Racks:Supply, installation, testing & commissioning of double section 19" wall mounted pivoting type, 24 U height& 800 mm depth rack having safety glass door & withstandard accessories, including power supply panel, fans,cable manager, full cable entry plate with brush at top & bottom etc. complete as required & as per instructions ofEIC.

CAT-6A Cable : Supply, installation, testing & commissioning of CAT-6A UTP cable including Providing and fixing of 25mm dia MS/PVC (HMS variety) conduit on 5mm. thick G.I. spacers fixed with no. 10 nettle fold wood screws with nylon plug complete with all conduit accessories 20 SWG G.I. Saddles etc. for uplinking between patch panels, as required, including termination including end termination at both ends complete with all accessories all as required & as per instruction of EIC. TOTAL COST OF LAN SYSTEM WORKS

Lightning Protection System : Section -VI:LIGHTNING PROTECTION SYSTEM Supply, installation, testing & commissioning of test link box suitable for and consisting of 37 X 6 mm, heavily hot dipped GI test link, 25 X 8mm GI nut bolts & washers, suitable enclosure made of 2mm thick MS CRCA sheet with GI fixing screws/anchor fasteners etc., complete all as per STD drawing CSG/EM/STD -26 , specifications and as per the instructions of Engineer-in-charge.

Supply, installation, testing & commissioning of 25 x 6 mm heavily hot dipped GI earth strip for roofs conductors fixed on roof/wall/slab/ column with 5mm thick GI spacers fixed with no. 10 GI wood screws & 2 mm thick GI saddles with GI machine screws, interconnection of earth strip with welded joints and GI nut bolts & washer painting with two coats of metallic paint, etc. instructions of Engineer-in-charge.

Supply, installation, testing & commissioning of 25 x 6 mm heavily hot dipped GI earth strip for down conductors fixed on roof/wall/slab/ column with 5mm.thick GI spacers fixed with no. 10 GI wood screws & 2 mm thick GI saddles with GI machine screws, interconnection of earth strip with welded joints and GI nut bolts & washer painting with two coats of metallic paint, etc. instructions of Engineer-in-charge.

Supply, installation, testing & commissioning 37 X 6mm heavily hot dipped GI earth strip for ground conductors fixed with no.10 GI wood screws & 1-2 mm thick GI saddles with G.I machine screws or in ground at 750mm below including excavation in all types of soil/rock with temporary reinstatement & back filling of trench,interconnection of earth strip with welded joints and GI nut bolts & washers, painting with two coats of metallic Aluminium paint for above ground portion & painting with two coats of black bituminous compound for earth strip in ground etc. all as per drawing, specifications and as per the instructions of the Engineer-in-charge. TOTAL COST OF LIGHTNING PROTECTION SYSTEM

Section -VII: MISCELLANEOUS ITEMS : CABLE TRAYS AND CABLE MANAGEMENT SYSTEM : Supplying and fixing following sizes of GI wire mesh tray,hot dipped galvanised between 60 and 80 microns of zinc as per BS 729 carbon Steel cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required, and duly suspended from the ceiling with electro-zinc coated TF rods, wall mounting brackets etc. 150mm width x 50 mm depth

500mm width x 50 mm depth

M. S. Boxes : Fabrication, supply and installation of M.S.boxes with 2 coats of primer & 2 coats of enamel / PU paint as per instructions of EIC.

MS Fabrication : Supply, fabrication and installation of supports using MS channel/angle / flat/ MS rod hangers etc.including cutting, fabrication, welding etc. and painting with two coats of primer and two coats of enamel/ PU paint of approved shade as per instructions of EIC.

Supply & installation of 250 mm dia heavy duty RCC Hume pipe of class 'NP3' to be laid in ground/from concrete cable trench to ground, for passing of cables with necessary joints, concrete supports. Scope includes escavation below ground level in all types of soil/concrete road cutting/foot path cutting, nallah cutting /any RCC wall/floor cutting including back filling, dewatering,consolidation, reinstatement of excess earth within the radius of 500 m and original,disposal making good to the original finish etc. spare space of hume pipes after cable laying and spares hume pipes shall be sealed properly with fireproof materials.

Supply, installation of GI pipe of B class sleeves in beams/column/slab for passing electrical cables/conduitas per instruction of E-I-C. 80 mm dia

150 mm dia

Blank PVC (HMS) Conduits : Supply & installation of high mechanical stress (HMS)rigid PVC conduit having ISI marked IS 9537 Part - 3,including fixing accessories & hardware concealed/exposed in slab/wall or on 5mm. thick G.I. spacers fixedwith no. 10 nettle fold wood screws with nylon plug complete with all conduit accessories 20 SWG G.I.Saddles, MS/PVC pull out boxes, MS/PVC junction boxes,couplers, bends binding wires etc. as per site condition & as per instructions of E-I-C and of following sizes :- 25 mm dia

40 mm dia

Flexible steel Conduit : Supply, installation, testing & commissioning of 25mm and 50mm liquid tight, FRLS , PVC coated Flexible Galvanised Steel conduit made up of helical coil of self interlocked ribbed stripes of Galvanised steel complete with necessary for rooftop solar PV system : 25mm conduit fixed to wall / slab / column / beam with 2mm thick GI saddle & 4-5 mm thick GI Spacer

50mm conduit fixed to wall / slab / column / beam with 2mm thick GI saddle & 4-5 mm thick GI Spacer

25mm on rooftop surface , laid along with earthing strip & clamped with earthing strip at every 200mm using 14 SWG GI wire.

50mm on rooftop surface , laid along with earthing strip & clamped with earthing strip at every 200mm using 14 SWG GI wire.

Supply, fixing & installation of pre mixed & ready to use M/s. HILTI make firestop foam CP 620 in 300ml bottle for sealing openings in electrical shafts, Telephone shaft,raceways & cutouts, hump pipes & where ever required & as per instruction of EIC.

Supply, fixing & installation of pre mixed & ready to use M/s. HILTI make firestop mortar CP 636 for sealing openings in electrical shafts, Telephone shaft, raceways & cutouts, hump pipes & where ever required & as per instruction of EIC.

Supply & laying of 50/42 mm OD/ID self lubricated HDPE pipes in ground at depth of 600 mm including cutting of existing footpath,road etc, sand bedding,laying of warning tape on top,temporary reinstatement. backfilling ,dewatering if necessary consolidation,disposal of excess earth with in the radius of 500 m etc. or fixed onwall/column/slab with 5mm thick M.S. flat /GIspacer/angle/ support fixed with coach screws/ grouted inwall/anchor fasteners 2mm thick G.I. fabricated saddle, all fixing accessories, etc complete including painting of M.Sspacers/angles all as per the attached work specification and instructions of EIC. Note: 1) The scope of work includes HDPE pipe accessories suchas couplers, cable end plugs, cable sealing plugs etc. On wall/ slab/ column/false ceiling/existing cable tray/existing hume pipe/trench/shaft/pit etc

Supply & fixing of rigid self adhesive photoluminescent AUTOGLO sheet for indoor of different sizes & signage’s as per instruction of EIC.

Providing and Fixing 19 mm thick Fire Retardant Ply IS 5509-1980 for meter cabin at all locations including cutting to required sizes and jointing and fixing the same with necessary screws etc. as directed by the Engineer-in-Charge.

Excavation of Earth : Excavation of earth in following type of soil as per Specification All types of soil including murram

Hard Rock TOTAL OF MISCELLANEOUS ITEMS

SECTION VIII -: LED Luminaire ,Ceiling fan, Exhaust fans etc Supply, installation, testing & commissioning of LED luminaires complete with accessories etc on surface of slab/beam by 2 nos (minimum) of 6 mm anchor fasteners or on wall with 2 nos of wood screws, nylon plug etc.,suitable supporting frame fixed with rag bolts grouted on the wall/anchor fastener on the beam/on the column & other fixing accessories etc provision & connection with 1.5 sq.mm multistranded copper conductor FRLS PVC wires etc., all as per drawing, specifications & as per the instruction of E.I.C. Notes: 1) Sample luminaire/fittings shall be got approved from Dept with complete technical data. 2) All luminairess shall be with drivers. 3) Cost of mounting accessories shall be included in luminaires cost. 4) The lumen output indicated is minimum system output of luminaire (Bidder to mention the wattage of Luminaire Quoted under sub points 1.1 to 1.4). 5) No negative tolerance is allowed on minimum system performance parameters indicated in the SOQ and specifications. 6) The CCT of the luminaire shall be decided at time of work execution. Surface mounted LED luminaire 1500 lumen output similar to M/S Signify make cat no: SM200C LED 16S PSU'Cirrus mini' or eq. approved

Surface mounted LED luminaire 4400 lumen output having min IP 65 similar to M/s Signify make cat no: WT 201C LED 44S 6500 L120 PSU WH or eq. approved

Surface mounted LED luminaire 4000 lumen output similar to M/S Signify make cat no: BN 308C LED 40S 6500 L120 PSU WH or eq. approved

Area light LED luminaires having a minimum efficacy of 110 Lumen/watt and minimum output of 7000 lumens with 4000 to 5700 degree K CCT & pressure die cast Aluminium housing , UV stablised polycarbonate /toughened glass diffuser havinh IP66 &IK07 protection as per specification

Emergency Luminaire : LED egress surface/recess, maintained type luminaire (double side viewing) in corridor near staircase with 1 hour backup similar to PEL LED E/M of M/s Prolite with all required hardware, egress symbols etc as per instructions of EIC.

Fan Hook Boxes Supply, installation, testing of concealed fan hook boxes of size 150 x 150 x 75 mm deep fabricated out of 2mm thick M.S CRCA sheet with nominal 12 mm dia M.S tested rod hook with brass earthing stud & welded nut from inside and 2mm thick round M.S cover plate overlapping by 15mm, including red oxide and two coats of white synthetic enamel paints and brass chromium plated screws and cup washers for fixing and all as per conceptional drawing No.:CED/EM /STD/11 R4 & instruction of Engineer-in-charge(Sample box with cover to be got approved before fabrication including the fabricator)

Swivelling Bracket: Fabrication, supply & installation of swivelling bracket for area light luminaires with 1500 mm long, 25 mm nominal bore dia G.I. pipe (class-B) as per IS 1239 bent into required shape for bracket & fixed in 450 mm long ,32 mm nominal bore dia GI pipe class-B having 3 nos of clamping arrangment made up of 300 mm long 40x5 mm G.I. strip, welded suitably to it (32 mm dia G.I. pipe) including making 2 nos of 8mm holes on 32 mm dia G.I. ppe for welding suitable nuts on pipe with required bolts for tighting the bracket fixed on surface of wall/slab/beam by 6 nos of minimum 10mm anchor fastners with coach screws,painting of whole bracket with two coats of enamel paint by dipping method etc. Note: Scope laso includes providing earthing to bracket by interconnecting with 1.5sqmm wire to junction/terminal box. TOTAL OF LIGHTING LUMINAIRES

SECTION- IX : TELEPHONE SYSTEM Telephone Point Wiring: Point wiring with 4 pair CAT-6 wires copper conductor PVC insulated, including Providing and fixing of 25-40 mm dia rigid PVC conduit (HMS variety - ISI marked,conforming toIS 9537 Part-III) concealed in slab /wall or surface with 5mm thick G.I.spacer & 20 SWG GI Saddle fixed with nylon plug, wood screws etc. complete with all conduit accessories suitable MS pull boxes of suitable sizes as persite condition wherever required M.S. telephone point accessories boxes fabricated out of min 18 SWG/20 SWGthick CRCA sheet zinc passivated , brass earthing studs 1/2 nos., RJ-11 telephone socket outlets with shutter ferrule numbers on both side of the circuits all terminations with ferrule /lugs if required, labelling all as per drawing specifications & as per instructions of E-I-C. NOTE: 1. Point wiring means 4 pair CAT-6 wires from TelephoneTag Block to assigned point including end termination ofone pair at both sides and other pairs should be keptspare. 2. G.A drawings & fabrications drawing are to be got approved from E-I.C. Point wiring for telephone point with 4 pair CAT-6 wire with RJ 11 jack type socket with shutter in a box with connector

Telephone Tag Block (TTB) : Supply, installation, testing & commissioning of following readymade Krone connector telephone tag block box, 18SWG MS CRCA sheet, concealed/surface mounted on MS frame of size 40 x 40 x 5mm and grouted on the wall/fixed on the column free standing type with anchor fasterners,cable end/wire way box,if required, with adequate spacefacility to be provided in the TTB, with front operable hinged door, neoprene rubber/cork gasket for joints, wire bunching clamps , name plate etc. all as per standards,specification, drawing & instructions of E.I.C. Note: 1) Point distribution diagram shall put in side the DB withpolythene protective cover. 2) All fabrication drawings shall be got approved. 3) Disconnection module shall be Krone Part No.69011006-02 or equivalent approved. 200 pair telephone tag box : A set consisting of : 1)Disconnection module 2 /10 --> 20 nos. 2)Back mounting frame - 2/11 --> 1 nos( C.T. box with mounting bracket ) 3) Transparent dust cover --> 1 no. complete with all accessories 4) Label Holder - 1 nos.

50 pair telephone tag box : A set consisting of : 1)Disconnection module 2 /10 --> 5 nos. 2)Back mounting frame - 2/11 --> 1 nos( C.T. box with mounting bracket ) 3) Transparent dust cover --> 1 no. complete with all accessories 4) Label Holder - 1 nos.

Telephone cables & end joints. Supply, installation, testing & commissioning of jelly filled telephone cable with copper conductor, PE insulated, cores twisted, G.I. wire/strip armoured, PVC sheathed cable fixed on wall/ column / slab on 5mm. thick GI spacer/MS flat support fixed with wood screws with 20 SWG GI saddle etc all fixing accessories and as directed by E-I-C. 0.5 mm dia 200 pair Telephone cable

0.5 mm dia 50 pair Telephone cable

End jointing of Telephone cable with all jointing materials like cable gland, ferrule lugs, ferrule numbers, wire dressing clamps/button tapes, etc. complete including all jointing materials and with necessary special tool kit for KRONE type connector and as directed by E-I-C. 0.5 mm dia 200 pair Telephone cable

0.5 mm dia 50 pair Telephone cable TOTAL COST OF TELEPHONE SYSTEM

SECTION- X : TV SYSTEM T.V. point wiring complete with RG-6 solid co-axial copper conductor cable from spliter provided near staircase area including Providing and fixing of 25mm dia PVC (HMS) conduit in slab/wall or on the surface of slab/wall with G.I spacers & saddles fixed with nylon plugs, wood screws with all conduit accessories, suitable MS pull boxes/junction boxes, complete with modular T.V. socket outlet in readymade 18 SWG CRCA sheet zinc chromate passivated brass earthing studs etc as required with connections at both ends all as per the instruction of E.I.C.

Supply,installation,testing & commissioning of RG-11 solid co-axial copper conductor cable including Providing and fixing of 25mm dia PVC (HMS) concealed conduit in slab/wall or on the surface of slab/wall with G.I. spacers & saddles fixed with nylon plugs, wood screws with all conduit accessories, suitable M.S. pull boxes / junction boxes complete with connections at both ends (Between spliter to spliter /amplifier box) as per instruction of Engineer-in-charge.

Supply & installation of MS Box of 160 X 160 X 100 mm deep made of minimum 18 SWG thick CRCA sheet for T.V. antenna spliter box (concealed type ) with 4 way splitter with power pass & with knock-outs & front door with concealed hinges, locking arrangements complete with name plate, painting, and as per instruction of E.I.C TOTAL COST OF TV SYSTEM

SECTION- XI : Elevator Design, fabrication, manufacture, assembly, delivery to site, installation, testing, commissioning and handing over of 1000 kg (13 passenger) lift having contract speed of 1.0 m/s serving different floors in the existing lift shaft as per detailed specifications enclosed, lift rules, IS, as per instructions of E-I-C and as under: 1. Machine room less with gearless electric drive 2. Duty load : Min 800 kg 3. Speed : 1.0 m/s 4. Floors served : 5 (Including terrace) 5. Travel :15 m (approx) 6.Stops & opening : 4 (same side including terrace). 7. Controller : A.C. variable voltage & variable frequency with closed loop control. 8. Operation : Microprocessor based Simplex / duplex full collective with /without attendant. 9. Power - 415 V, 3 phase, 50 Hz, 4 wires system 10. Type of doors : a) Car : Power operated, centre opening horizontal sliding stainless steel doors in honeycomb/ SS vandal proof finish with sandwich construction. b) Landing doors : Centre opening horizontal sliding stainless steel doors in honeycomb / SS vandal proof finish with sandwich construction. c) Tamper proof infra-red full width and full height of the opening with protective leading edge device as backup protection. 11. Lift car floor: Granite flooring of approved pattern. 12. Automatic rescue device complete with dry maintenance free batteries as required.13. BMS compatible feature in elevator controller as per specifications. TOTAL COST OF ELEVATOR WORKS

M.S SEAMLESS PIPES: Supply, Installation, Testing and Commisioning of MS seamless pipe of following Sizes and conforming to ASTM 106 A, Grade B with all fittings, flanges, jointing, supports (Support for piping shall be paid separately) and painting with two coats of anti corrosion paints over two coats of red oxide primer (for laying above ground) and including providing wrapping with 4 mm thick PYPKOTE(corrision protection tape) with adhesive / coats as required(for laying underground) including all the hardware, complete in all respects of work, all as per drawings, specifications and as instructed by Engineer-In-Charge. NB : 1) Making of flanged joints including providing fasteners, blind flanges and gaskets shall be measured under pipelength of this item and no extra payment shall be made. 2) Pipe support shall be paid under Item no. 15 100 mm dia. (Below Ground)

100 mm dia. (Above Ground)

G.I. PIPES: Supply, installation, testing and commissioning of Heavy Duty, "C" Class GI pipes of following sizes confirming to IS-1239 (PART-I) along with all necessary fittings, flanges, jointing ( welded / flanged etc.) and required supports with two coats of paint as per color code of the piping systems over two coats of red oxide primer, including all hardware, complete in all respects as per specifications and as instructed by Engineer-In-Charge. NB : 1) The pipe line shall be measured along the centre line. 100 mm dia. .

50 mm dia.

CI GATE VALVES: Supply, installation, testing and commissioning of double flanged CI/Cast Steel Gate Valve of required sizes of ratings PN 1.6 with rising stem conforming to IS-14846 with all necessary fittings like flanges, neoprene gaskets, nut bolts, hardware, flange joint etc. as shown in the drawings and as per specifications and as instructed by Engineer-In-Charge. 100 mm dia.

GUN METAL GATE VALVE: Supply, installation, testing and commissioning of heavy pattern screw down Gun Metal Gate Valves of following sizes confirming to Class 2 of IS : 778 with hand wheels at top including testing for a pressure of 16 kg/sq.cm. for two hours, all as per specification, drawings and as instructed by Engineer-In-Charge. 50 mm dia.

NON RETURN VALVES:Supply, installation, testing and commissioning of double flanged CI/ Cast Steel non return valves of following sizes of ratings PN 1.6 inline with relevant IS(flap/ball type) with gun metal working parts & CI body and including all necessary fittings like flanges, neoprene gaskets, nuts bolts for fixing with pipe, hardware, joints etc. as per drawings, specifications and as instructed by Engineer-In-Charge. 100 mm dia.

SINGLE OUTLET HYDRANT LANDING VALVE: Supply, Installation, testing & commisioning of Single Outlet Hydrant landing valve of oblique Morris pattern Stainless Steel (SS-304) landing valve with C.I./ S.S. hand wheel, detachable stainless steel female coupling, conforming to IS-5290/BS-5041 having instantaneous coupling, having 63 mm dia. blank cap and chain conforming to IS-901 to suit the hosepipes, including nuts, bolts, washers, gaskets, with necessary fittings like tees etc. testing the unit, painting the Hydrant landing valve with 2 coats of signal red paint over a coat of Zinc reached primer, all as per specifications and as directed by E-I-C.

TWO WAY SIAMESE CONNECTIONS: Supply, installation, testing & commissioning of Siamese connections having two numbers of 63 mm diameter G.M/SS inlet (instantaneous male coupling) along with one number 100 mm diameter C.I. double flange non return valve of rating PN 1.6 conforming to IS 5312 with G.M working parts, one number 50 mm dia G.M drain valve of class-2 conforming to IS 778 and fittings all connected to 100 mm diameter MS pipe with necessary fittings including blank caps, flanges and joints, welding etc. and supplying and fixing of inlet housing box made out of 14 gauge M.S Sheet with angle and frame of suitable size and painting with two coats of synthetic enamel paint over a coat of approved primer over pipes and housing box and white enamel paint inside housing box complete in all respects as per specification and as instructed by E-I-C.

HOSE REEL WITH DRUM: Providing & fixing rubber hose reel of 20 mm diameter x 37 m along with swinging drum along with high pressure braided rubber hose conforming to IS 884 including 8 mm diameter SS cut off nozzle on one end, wall mounting type, necessary brackets suitable for wall mounting, fixing on wet riser cum downcomer including connecting the other end to the wet riser cum downcomer by providing necessary connecting nipple/coupling, nuts, bolts etc. and providing & fixing 20 mm dia G.M. peet valve of approved make all complete including painting (the drum and brackets shall be painted with two coats of signal red enamel paint from outside and white enamel paint from inside) & as shown and as instructed by Engineer-In-Charge.

HOSE CABINET: Supply, installation & commissioning of 1.6 mm thick MS sheet metal hose cabinet of size 750x650x250 mm for accomodating 02 nos. of hose pipes (measured & paid seperately under relevent SOQ item) and SS-304 branch pipe with nozzle or hosy branch pipe with nozzle. The box shall have front glass door lock with angle iron frame. The hose pipe box shall be fixed with Hilti make Anchor Fastner on the wall or nut bolts (in case of stand in open space) as shown in the drawing and as directed by EIC. The MS box shall be painted with two coats of signal red enamel paint from outside and white enamel paint from inside. The scope also includes supplying of gun metal / stainless steel branch pipe of 63 mm dia. fitted with detachable hexagonal nozzle of 19 mm dia. conforming to IS : 903 or universal pattern as per IS : 2871. The branch pipe with detachable nozzle shall be placed in the hose cabinet complete in all respect as instructed by Engineer-In-Charge.

HOSE PIPE (For Hydrants, Landing Valve): Supply and installation of Unlined Flax Canvas (hose pipe) for fire fighting conforming to RRL fire hose type A or Synthetic Fibre Woven-Jacket (SFWJ) Elastomeric fire hose type B conforming to IS:636 all with ISI marks as required and of approved make and of 63 mm dia & 15 mtrs length, fitted with male and female SS coupling confirming to IS:903, ISI marks with guaranteed bursting pressure of 35.7 kg/sq.cm and complete as per the technical specifications and as instructed by Engineer-In-Charge. Each set shall comprise of 2 hose pipes.

PRESSURE GAUGES (Range of 0 - 10 Kg/cm2):Supply, installation testing and commisioning of pressure gauges of SS material with dial not less than 150 mm dia of appropriate range and complete in all respects with shut off gauge, cocks , all fittings etc, duly calibrated before installation in MKS and FPS units and duly tested after installation as per drawing and as instructed by Engineer-In-Charge.

AIR RELEASE VALVES: Providing and fixing 20/25 mm dia. (PN - 1.6, Type-S1, Flanged, ISI marked) air release valve conforming to IS - 14845 : 2000 with Double Flange isolating valve (pressure rating PN 1.6) including making necessary flanged joints and providing all fitting materials nuts, bolts etc. and providing T on the pipeline for its installation at site all as per technical specification, drawings and as instructed by Engineer-In-Charge.

M.S. SUPPORTS/STRUCTURE: Supply, cutting, fabrication, welding, erecting & fixing in position of M.S. support/structure (angle, channel, beam, plate, chequered plate etc.) for steps and other purpose (not applicable for items for which supports are already included in the item) including painting with two coats of synthetic enamel paint of approved make & shade over a coat of approved steel primer all as instructed by Engineer-In-Charge. Material shall conform to IS-2062.

PCC PEDESTALS: Providing PCC pedestals /thrust /anchor block of required sizes for underground pipes, fire hose box etc. and specials with cement concrete 1:2:4 at required intervals including (frame work) shuttering, curing, finishing etc. complete in all respect as as per standard specifications and as instructed by Engineer-In-Charge.

VALVE CHAMBERS: Construction of brick masonary valve chambers made out of 230 mm thick brick masonry in cement mortar 1:4 over a bed of 150 mm thick cement concrete of grade M-15 for foundation with 150 mm extended all round the walls, including providing and fixing suitable size staircase for landing inside the chamber. The staircase shall be fabricated out of 25 mm dia. M.S pipe and 6 mm thick M.S Sheet suitably painted with 1 coat of primer and 2 coats of synthetic enamel paint. Racking out joints & plastering in cement mortar 1:3, 20 mm thick both on internal and external surfaces, internal surfaces finished smooth with a floating coat of neat cement. Providing 6 mm thick Aluminum chequered plate in sectional construction with suitable lifting arrangement and painting. It shall be complete as per technical specifications, drawings and as instructed by Engineer-In-Charge. NB.: The cost of all the items mentioned above is to be included under this item and no extra payment shall be made. 1.0 m width x 1.0 m length x 1.2 m depth

FIRE EXTINGUISHERS Proividing & fixing of Dry Chemical Powder (ABC) type fire extinguisher of 06 Kg capacity either portable or trolley mounted as per approved make fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged with ABC powder (Mono Ammonium Phosphate) pressured by Nitrogen complete in all respects including wall suspension bracket and conforming to IS 15683-2006. The Fire extinguisher shall be supplied and placed without any damage, scratches and loss of accessories as per specifications and as instructed by Engineer-In-Charge.

Providing & fixing of, CO2 type fire extinguisher of 6.5 Kg capacity either portable or trolley mounted, highly effective against B & C class of fire, having ISI certification mark, having flat base including valve, discharge hose & complete in all respects including initial fill with CO2 gas conforming to IS 15683:2006, wall suspension bracket as required & as per instructions of Engineer In Charge. The Fire extinguisher shall be supplied and placed without any damage, scratches and loss of accessories as per specifications and as instructed by Engineer-In-Charge.

Remote ON / OFF P.B. Station: Supply, installation, testing and commissioning of 14 SWG MS CRCA sheet, remote ON/OFF push button enclosure, with ON / OFF indication lamps, IP 42, wall mounting type, powder coated with RAL 7032 shade complete with internal wiring with 1.5 sq.mm copper PVC FRLS wires etc. Note: 1) ON - OFF indication lamps shall be heavy duty LED type, 240V, 50 Hz 2) PB station shall be lockable type to prevent unauthorize operation of booster pump.

M.V.Cables: Supply, installation, testing & commissioning of 1.1 KV grade XLPE insulated, inner sheath PVC tapped, extruded FRLS PVC outer sheath, GI strip / wire armoured, multistranded Aluminium / copper conductor power cable confirming to IS : 1554 part I/IS 7098 part-1 with upto date amendments, fixed on wall/column/slab/false ceiling or in existing hume pipe/trench/ shaft/pit/ on 5mm thick M.S. flat /GI spacer/angle/ support fixed with coach screws/grouted in wall/anchor fasteners 2mm. thick G.I. Fabricated saddle, all fixing accessories, etc complete including painting of M.S spacers/angles and saddles all complete as per enclosed detailed specifications, drawings & as per instructions of the E-I-C & of the following sizes. The space between the two support shall be 600mm. approx. 4 C x 6 sq.mm copper conductor cable (On Wall / Trench / Cable tray)

3 C x 4 sq.mm copper conductor cable (On Wall / Trench / Cable tray)

End Joints: End jointing of following sizes of cable by crimping with supply of all jointing materials like solderless tinned copper cable socket, cable glands, gland earthing, insulation tape, flux, duplicate interconnection between gland earthing strip & to the nearest earthing bus terminals as per the drawings, specifications and as per the instructions of the Engineer-in-charge. 4C X 6 sq.mm. copper conductor cable

3 C x 4 sq.mm copper conductor cable

Control Cable: Supply, installation, testing & commissioning of 1.1 KV grade multicore copper solid / stranded conductor of size 3 C x 2.5 sq.mm, PVC insulated, FRLS PVC outer sheathed armoured cable between various sensors and starter etc. on existing cable tray/surface on 5mm thick M.S. flat /GI spacer/angle/ support fixed with coach screws/grouted in wall/anchor fasteners 2mm. thick G.I. Fabricated saddle, all fixing accessories, etc complete including painting of M.S spacers/angles and saddles etc. providing brass cable number tag as per enclosed detailed specifications, drawings & as per instructions of the E-I-C .The scope also includes end connections at both ends with glands etc. as required.

Earthing System: 4 SWG GI strip/wire fixed to wall/side of trench/ slab/column/beam/shaft with 5mm thick G.I spacers & GI saddles or on existing cable tray etc. TOTAL OF FIRE FIGHTING WORK

M/s. R. M. KATORE AND CO.

H.C.KATARIA

S.T.BIRADAR ENGINEERS & CONTRACTORS PVT.LTD.

M/S P N NAGANE

ABL INFRASTRUCTURE PVT. LTD.