REPAIR TO FLOORING PLASTERING TILING JOINERY SANITARY FITTING AND MISC WORK IN DAD MD ACCN UNDER AGE BR I OF GE NORTH MEERUT CANTT

Amount

S&F factory made glazed, gauzed and skeleton shutters 35 mm thick 2nd class hardwood (SAL/ CHAMP / HOLLOCK) open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); for doors and fitted to chowkats complete all as specified and directed.

S&F plain framed, panelled shutter (two panel) factory made 35 mm thick of 2nd class HW with rail stile and lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part-I), Kiln seasoned and chemically pressure treated, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) not exc. 1.5 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) exc 1.5 sqm but not exc. 4 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

Taking down shutters of any description exc 1 but n exc 2 sqm each, including builders hard ware fittings complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined to gether with solvent cement, suppling & fixing in the frame at site as per specification & drawing on srl page No 156 of SSR Part-II complete all as specified and directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing shown on page 160 of SSR Part-II complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section, having shoot / dia of bolt not less than 12mm complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section, having shoot / dia of bolt not less than 12mm complete all as specified and directed.

S&F 300 mm long aluminium anodised, sliding door bolts, with haps staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts not less than 16mm dia of shoot / bolt of sxtruded section or cast aluminium alloy complete all as specified and directed.

S&F butt hinges of 100 mm size, Medium weight, cold rolled mild steel. complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised,width of flap (when open ) 40 mm. complete all as specified and directed.

S&F 150mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate . complete all as specified and directed.

Supply and fixed 125mm size extruded aluminium alloy handles, fabricated type., anodised complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type., anodised complete all as specified and directed.

S&F hasp and staple, aluminium anodised, saftey type, including bolt to hinge plate and fixed with screws, Size of hasp and staple 125mm complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples including necessary beadings complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples including necessary beadings complete all as specified and directed.

S&F mild steel work as for framed work such as grills gratings, etc., with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed baluster; walk ways; railings; framed work of water tanks and similar work including necessary riveting and / or welding conforming to Fe 290 (Gde-E 165) complete all as specified and directed.

S&F rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S&F factory made steel windows with side hung shutter including projection type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F factory made steel windows with side hung shutter including projection type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges,. Steel peg stay and including treated with tar or coal tar black paint on steel surfaces in contact / embedded in concrete / masonary work complete all as specified and directed. (Note : Disturbed surface of wall shall be made to good to tune surface)

M&L for 25 mm thick PCC (1:2:4) type B1, (using 12.5mm graded crushed stone aggregates) as in sub base & floors complete all as specified and directed.

M&L for water proofing treatment to existing non-accessible roof slabs by providing 10mm thick bedding layer of cement mortar 1:3 mixed with water proofing compound as per manufacturer's instructions and preparing, cleaning new concrete/plastered surface and applying evenly a tack coat @1.20 kg/sqm with 85/25 industrial bitumen over a coat of bitumen primer conforming to IS 3384 @ 0.30 liter/sqm and laid with 3mm thick APP modified polymeric water proofing membrance with non-woven polyester rainforced and applying a tack coat of 85/25 industrial bitumen @ 1.2 kg per sqm and finish the surface with aluminium paint at top @ 0.2 kg/sqm as per manufacturer's instructions. Weight of membrane shall not be less than 3.6 kg/sqm unrolled and bonded to substrate with side and end laps 75mm & 100mm as per manufacturer's instructions. complete all as specified and directed. Note :- The WPT work shall be got done through manufacturer's authorised applicator only under strict supervision of manufacturer's technical representative.

M&L for 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in cupboard sheleves kitchen cuboard etc including taking down existing material complete all as specified and directed.

M&L for 6mm thick external teak wood lipping fixed to 18/19mm thick block or Veneered particle boards with nails complete all as specified and directed.

M & L for laying Non Skid ceramic tiles 7 to 8 mm thick, (square / rectangular) jointless area of each tile exc 0.11sqm but n.exc 0.18 sqm first quality coloured of grade B II (a) /B II (b) and of abrasion resistance - PE I -III or above , in floors etc, set and jointed in neat cement slurry over and including screed bed or bedding layer of 15mm thick cement martar 1:6 complete all as specified and directed".

M&L for Glazed ceramic tiles coloured 350mm x 250mmx 7 / 450 x 350 x 8 mm thick first quality of grade B tiles on vertical surface such as skirting / dados etc set in neat cement slurry over and including 10mm thick backing coat / bedding layer in CM 1:4 complete all as specified and and directed

M&L for laying 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in floor/plinth protection, cement concrete surfaces finished even & fair without using extra cement complete all as specified and directed.

Dismantling of floor, hearth or wall tiles / terrazzo including cement mortar bedding (but not backing),removal servicable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete vertical surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:4 on ceiling of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work concrete surface in CM 1:4 mixed with water proofing compound and surface finished even and smooth without using extra cement (WPC shall be measured and paid separately) complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified and directed.

M&L for three coats of white wash on newly plastered or unplastered surfaces of ceiling including preparation of surface complete all as specified and directed.

M&L for preparing the new plastered surfaces and applying two coats of oil bound distemper over a coat of primer on walls completeall as specified and direcrted.

M&L for preparing the newly plastered surfaces and applying two coats of cement base paint on walls / vertical surfaces complete all as specified and direcrted.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying two coat of white / tinted synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for 3 mm thick sheet glass, ordinary quality and glazing with oil putty or glazing pins in square n exc 0.5 sq. m in each pane complete all as specified and directed.

Hacking out old broken glass (any thickness, size,quality or description) from metal frames including punching or drilling out old glazed pins / spring clip and providing and fixing new ones complete all as specified and directed.

Taking up or down GI water tubing 15mm bore and connection including cleaning serviceable pipes for refixing and unserviceable removal from the site complete all as secified and directed

Taking up or down GI water tubing 20mm bore and connection including cleaning serviceable pipes for refixing and unserviceable removal from the site complete all as secified and directed

Supplied and fixed GI water tubing 15 mm bore medium grade with all fittings fixed to walls and ceiling or laid in floors including cutting screwing and waste etc complete all as specified and directed.

Supplied and fixed GI water tubing 20 mm bore medium grade with all fittings fixed to walls and ceiling or laid in floors including cutting screwing and waste etc complete all as specified and directed.

Dismantling of old water tank exc 500 Ltr & n.exc 1000 Ltr capacity and Supplied, hoisted and fixed inposition rotational moulded polyethylence water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with closed top) of 500 Ltrs capacity with and including 20mm dia Ball valve high pressure of PTMT with apoxy aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed.

Cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes etc incl washing the tank with bleaching powder for capacity of tank exc 250 litres but not exc 500 litres complete all as specified and directed

------------------BLANK--------------------

S&F in repairs 20mm bore dia Ball valve high pressure of PTMT with epoxy aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms complete all as specified and directed.

Supply only Integral water proofing compound (I.S.I marked on packing)complete all as specified and directed.

S&F in repairs C P bib taps, cast copper alloy fency type with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule of 15 mm bore and fixed complete all as specified and directed.

S&F in repairs pillar taps, 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fixed in repairs stop valves, 15mm bore dia, cast copper alloy, CP fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed down both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S&F chromium plated over head shower 100mm dia round shape single flow ABS Body chrome plated with gray face plate) with rubit cleaning system. Make : Jaquar,Essco (Cat No : EOS - 542N) complete all as specified and directed

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supplied and fixed Stainless steel grating doom 100 mm dia and waste hole (minimum weight 40 gms) complete all as specified and directed.

Supplied and fixed 110mm bore UPVC(SWR) pipes single socketed in any length with rubber ring joint, laid in trenches/under floor complete all as specified and directed.

Supply and fixing in repairs vitreous china squatting pan, Orissa' pattern, size 580 x 440mm white, with integral foot rests with and including cast iron 'P' or 'S' trap and setting the trap and pan in and including PCC 1:4:8, type D-2 minimum 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, making all connections complete all as specified and directed.

Supply and fixing in repairs PVC low level flushing cistern of 10 Ltr capacity syphonic action type with inlet ball valve, float and handle including PVC brackets for mounting of cistern including provision of 32mm dia PVC flush pipe of required length and making connections complete all as specified and directed.

S&Fin repairs sinks with drainage board made of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm X 203 mm with bowl size 405mm x 354mm x 203mm on top of Granite top cut to shap of sink including taking down old vitreous china sink of any type alongwith angle bracket etc complete all as specified and directed. (Note :- Granite plate form will be measured and paid seperately)

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glas shelf 12cm wide with chromium plated bracket guard and railing 60 cm long fixed in repair complete all as specified and directed

Demolition and breaking up drain pipes ( SGSW, AC or reinforced concrete) or PVC pipe set in cement mortar for 75mm / 100mm / 110mm internal dia of pipe and including removal from the site complete all as specified and directed.

Demolition of cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) and including removal of debris & rubbish from the site complete all as specified and directed. Note : Stone slabs / tiles and hard core of any description shall not be measured & paid under this item.

Carrying out cleaning work day to day complaints such as cleaning floor trap, nahni trap, gully trap cleaning of waste pipe of WHB, cleaning of WC, manhole, sewage line etc complete providing two nos Safaiwala at any location all as specified and directed by Engr-in-Charge

Carrying out carpenter work day to day complaints such as resecuring / adjusting of shutter, fixing of tower bolt window glass panes etc complete by providing skilled carpenter at any location all as specified and directed by Enger-in-Charge (store required will be provided seperately)

M & L for laying Non Skid ceramic tiles 600 x 600 x 7 to 8 mm thick, (square / rectangular) first quality coloured of grade B II (a) /B II (b) and of abrasion resistance - PE I -III or above , in floors etc, set and jointed in neat cement slurry over and including screed bed or bedding layer of 15mm thick cement martar 1:4 complete all as specified and directed".

Carrying out plumbing work day to day complaints such as repair / replacement of fittings and fixture, GI Tubing repair to flushing cistern fixing of bib taps, stop cock etc complete by providing skilled plumber at any location all as specified and directed by Enger-in-Charge. (Store required will be provided seperately).

M/S AMAR ELEKTRO CENTRE

GANGA ENTERPRISES

veer enterprises

Jain Engineering Works