SPECIAL REPAIRS TO SHAFTS OF MAP ACCN PKT II OF AIRMEN AND ADDN/ALTN AND IMPROVEMENT TO TOILETS AND CONNECTED WORKS AT CERTAIN OMQs AT HQTC (U) BANGALORE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. Note:- All debris & rubbish shall be removed from MoD land during at the end of each working period at his risk and cost in accordance with all applicable federal state a local regulation after removing debris the groung should be levelled/cleaned all as specified and directed by Engr-in-Charge.

M&L for glazed ceramic coloured/ digital/ stone finish wall tiles in vertical surface 600x300x7 to 8mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4 all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for. Note:- All debris & rubbish shall be removed from MoD land during at the end of each working period at his risk and cost in accordance with all applicable federal state a local regulation after removing debris the groung should be levelled/cleaned all as specified and directed by Engr-in-Charge.

M&L for 25 mm thick PCC (1:2:4), type B0 (Using 12.5 mm graded stone aggregate) as in flooring, all as specified and directed.

M&L for non skid Ceramic tiles coloured 7 to 8mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm each, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed of CM 1:6 all as specified and as directed

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:6 all as specified

All as per item No:06 but as in skirting over and including 10mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4 all as specified.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons incl granite slab in kitchen platform Laid, bedded and pointed in any mortar etc all as specified and as directed.

M&L for 20mm thick Granite of any type work (table rubbed and polished) in cooking plateform, widow sill, step, wall lining and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade granite incl 15mm thick mortar in CM 1:6.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame ) wooden not exceeding 1.5 Sqm each.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame ) wooden exceeding 1.5 Sqm not exceeding 4 Sqm each.

S&F 100mm long stainless steel Butt hinges,

S&F for 125mm stainless steel barrel tower bolts of extruded section and fixed.

S&F 125mm stainless steel handles,

S&F in repairs 150mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F second class hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints.

M & L 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed.

M&L for preparation of untreated new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and as directed.

S&F powder coated anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F in repairs powder coated anodised aluminium door, window and ventilator shutters (minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F in repairs sheet glass, of 4.8mm thick ordinary quality and glazing with oil putty in square exc 0.5 Sqm in each pane.

S&F 18/19mm Prelaminated medium density fibre particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

Supplying & fixing of Internal auto closing concealed hinge, Kutchina'/Hettich/Hafele make complete all as directed.

Supply & fixing of 6" premium quality crome finish Handle, "Kutchina"/Hettich/Hafele make complete all as directed.

Supply & fixing of good quality Telescopic channel set for drawer multi-tech high capacity 500 mm long , "Kutchina"/Hettich/Hafele Make.

S&F 19-20mm wide and 0.80mm thick decorative type PVC beading complete all as specified and directed.

S&F in repairs premium quality 15mm bib tap with wall flange chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified.

S&F in repair soap Dish Make-Jaguar Code No- CAN-1137/AKP-35731P

S&F in repair Toilet paper roll holder with flap of Make-Jaguar Code No- AKP-35753P

S & F in repairs single lever basin mixture with popup waste system with 450 mm long braided hoses all as directed Make: Jaquar-LYR-38051B/ORP-10011BPM

S & F in repairs table top basin of size 565X425X140mm of whitecolour complete all as specified and directed make-Jaquqr Cat No-KUS-WHT 35935/ JDS-WHT-0547

S&F in repairs premium quality 15mm bore wall mixer with hand shower system with provision for overhead shower complete with 115mm long bend pipe, connecting Legs & wall Flange of make Jaguar, Cera, Somany or equivalent.

S&F in repairs 15mm bore hand shower (Health Faucet) with 8 mm Dia, 1 Meter Long flexible tube & wall hook of make: Jaguar Cat No- ALD -573/ALD 577

S&F in repair Towel rail of 600 mm long Make-Jaguar Cat no-AHS-1507

S&F in repair glass shelf of 600 mm long with cp bracket.Make-Jaguar Cat no-CAN-1171N or equailent.

S & F Rimless Single Piece-WC with UF slim seat cover, hinges fixing accessories and accessories Set,Cistern fitting,size 380mmx670mmx765mm with hydraulic sheet cover and connecting to 'S' trap 300 mm incl taking down old complete.Make Jaguar FSS-WHT-29853S300UFSM / OPS-WHT-0205.

S&F in repairs CP connection 15mm dia and 450mm long with two Nos of brass checknuts and washers complete.Make jaguar cat no-ALD-805B.

S&F stainless steel Gratings size 125 mm dia complete all as specified & directed.

S&F Towel rack without lower hanger of 600 mm long and 03 no hooks Make-Jaguar Code No- AHS-1581

S&F Towel ring square with round flange of Make-Jaguar Code No-ACN-CHR-7721

S&F in repair angle stop cock with wall flange 15 mm dia chromium plated, screwed down, high pressure, screwed both ends for 15mm bore iron pipes or for unions, all as specified and as directed Make-Jaguar Cat no-CON 059KN

S & F in repairss fancy type CP 2 way bib cock with wall flanges fixed as in repair all as specified.

Taking up or down 15mm bore water tubing and connection building , or cleaning for refixing all as specified and as directed by Engineer In Charge.

Taking up or down 20 mm bore water tubing and connection building , or cleaning for refixing all as specified and as directed by Engineer In Charge.

Taking up or down 25 mm bore water tubing and connection building , or cleaning for refixing all as specified and as directed by Engineer In Charge.

S&F UPVC 15 mm dia pipe pressure rating 10 Kgf/cm2 with all fittings and fixed to wall /laid in floor complete all as specified and as directed by Engineer in Charge.

S&F UPVC 20 mm dia pipe pressure rating 10 Kgf/cm2 with all fittings and fixed to wall /laid in floor complete all as specified and as directed by Engineer in Charge.

S&F UPVC 25 mm dia pipe pressure rating 10 Kgf/cm2 with all fittings and fixed to wall /laid in floor complete all as specified and as directed by Engineer in Charge.

S& F 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or fixed with floor including necessary fixing cleats/ clamps, complete all as specified and directed.

S& F 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall including necessary fixing cleats/ clamps, complete all as specified and directed.

S&F in repairs 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed with wall including necessary fixing cleats/ clamps complete all as specified and directed.

S&F in repairs PVC bends of 110 mm dia complete all as specified and directed.

S&F in repairs PVC bends of 75 mm dia complete all as specified and directed.

PVC (SWR) branch piece, of 110 mm dia single (single Y) equal or unequal

Dismantling water tanks, capacity in litres exc 500 & n exc 1000 and removing to store.

S&F in repairs rotational moulded polyethylene water storage tanks, capacity in litres 1000 (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

S&F ball valves 25mm dia, high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms)

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25mm dia and fixed

S&F 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) including cost of two or more coats to give an even shade of plastic paint on ceiling with putty work complete with designer ceiling (with part ply,laminate and cove) as directed

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out in soft/ loose soil

Demolition of Brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dresses stonework and precast concrete articles.

M&L for Pre-cast cement concrete block masonry with solid blocks type C1, 1:3:6 ( 20 mm graded aggregate) exc. 10 cm in width and setting in mortar 1: 6 , complete all as specified.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. Including racking out joints, hacking for key, scrubbing down with water, etc. all as specified.

Rendering 5mm thick cement plaster in cement morter 1:3, on concrete sufaces as in ceiling, finished even and smooth without using extra cement.

M&L for preparation of old decorated surface on ceiling including washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of distemper oil emulsion through complete all as specified and directed by Engr in Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in Cement mortar 1:6, finished even and smooth with out using extra cement. all as specified and direction by Engr in Charge.

M&L Preparing new plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer on surfaces of walls.

M&L for two coats of Distempering on wall with distemper oil emulsion white or tinted over primer over a coat of 3mm thick wall care putty, including preparation of new surface all as specified.

M&L for 2coats of Distempering wall with distemper oil emulsion white or tinted through. over a coat of 1mm thick wall care putty, including preparation of old surface after complete removal of existing treatment all as specified and directed by Engr in Charge.

M&L for complete removal of existing treatment of walls and applying two coats of exterior emulsion paint (weather coat) through over a coat of approved primer complete all as specified and directed by Engr in Charge.

Preparation of old painted surface of any description not otherwise described wood and wood based surfaces over 10 cm width of girth and applying one coat of synthetic enamel paint all as specified and directed by Engr in Charge.

M & L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand

M&L for 50mm thick Cement concrete type B1, 1:2:4 (20mm graded stone aggregate) as in flooring, foot path, hard standing, plinth protection, bases of water tanks etc. all as specified.

M&L for 75 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) including finishing the surface even and fair complete all as specified and directed.

M&L for coloured designed chequered cement concrete tiles of a size 300x300x25mm thick with white cement & pigment in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match and including a 20 mm thick screed bed of cement mortar (1:6).all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) for hard standing including finishing the surface even and fair complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/ loose soil

M & L for plain cement concrete (1:3:6), type C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S & F mild steel tubular trussed, purlins, fencing posts,crane gantries rails and fastenings including special shaped washer etc complete using ERW or induction butt welded tubes Conforming to IS 1161-1979 grade St -240 all as specified and directed

Mild steel screw bolts, diameter of neck in 16 to 20mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10cm and n exc 15cm long

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/J hooks and bolts as reqd and specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheeting 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/J hooks and bolts as reqd and specified and directed.

M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxied priming.

S&F 10mm thick toughened glass corner bathroom cubicle of size 1.5 to 2.00m x 1.5 to 2.00m x 2.1m. With all necessary fittings ,brackets,handles stainless steel railing etc.. and joints tobe filled with silicon of approved make all as specified and directed by Engr-in-charge.

S&F factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor encludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose).

M & L Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the external wall below concrete or masonry spron using chemecal emulsion @ 2.25 ltrs per liners metre incl drilling and plugging holes etc in apron as all specified and directed by the Engineer in Charge.

M & L Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along treatment of soil under existing floors using emulsion @ one lts per hole 300mm apart incl drilling and plugging 12mm dia holes with cement mortor 1:2 (1cement : 2sand) to match the existing floors as all specified and directed by the Engineer in Charge.

M&L for Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) type C1, 1:3:6 ( 20 mm graded aggregate) and setting in mortar 1:6, complete in walls all as specified.

Cutting holes in walls built in cement mortar or cement lime mortar and wall of cement concrete exc 150 Sq cm but n. exc 400 Sq cm and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. all as specified and direction by Engr in Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement. including mixing of water proofing compound wherever required as per manufacturers instructions and as direction by Engr in Charge (WPC shall be measured & paid separately). .

M&L fo Rendering 10 mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling of chajja,roof projection,shelve etc and finished even and smooth without using extra cement all as specified and direction by Engr in Charge.

Supply only liquid water proofing compound of approved quality. (Make : CICCO NO.1/SIKA/ACCO PROOF).

S & F Mild steel flats (40x6mm thick) for hand rails, wind ties, posts and struts in fencing screwed or welded to shape as directed, including all necessary drilling, bolting or riveting etc., and similar work confirming to Fe 410 - O or Fe 310 - O

M&L for Plain Cement Concrete Type B0 , 1:2:4 (using 12.5 mm graded stone aggregate) cast in situ in cills and other similar bands, plinth courses, parapets, copings, hold fast ,bed plates and the like including use and waste of form work,weathering, slightly rounded or chamfered angles and throating as specified and directed.

Taking out/ down old existing water proofing treatment of sunken slab including cleaning the old RCC surfaces of sunken /lowered portion of slab surface for full depth of sunken floor by wire brush or chisel out any mortar sticking the surface and made suitable to receive water proofing treatment. The surface shall be cleaned and prepared in such a way to provide sound base, free from any oil, grease, dust or deleterious material which may impair adhesion of water proofing treatment. The surface preparation shall be carried out mechanically to remove contaminants, laitance & weak concrete, to expose blow holes and to produce a sound concrete with adequate profile and porosity. Any crack shall be treated with cementitious repair mortar of Fosroc, Renderoc CS or epoxy crack filling mortar or equivalent product by proper grooving method as per manufacturer's instruction and as directed by the Engineer-in -Charge.

Preparing the inside surface of core and PVC by roughening using suitable file to get better adhesion prior to bore packing (for reinstallation). Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Providing necessary formwork for packing the bore using suitable arrangement (depending upon site conditions). Applying a coat of styrenebutadiene based polymer coating using Nitobond SBR or equivalent product of Asian paints, M/S MC Bauchemic /CIPY/SIKA/Pidilite Dr Fixit/ Thermax/ STP admixed with integral WPC or cementitious crystalline waterproofing compound to enhance adhesion between the packing material and other surfaces. Packing the gap using nonshrink cement polymer-based grout using conbextra GP2 upto the surface of the bore whilst the Nitobond SBR is in tacky state. The above analysis is based on assumption for 150mm diameter core with 110mm diameter PVC for 5” thick slab only. Typical Properties Compressive strength at 28day as per BS 1881 45N/mm2, completely as per the manufacturer’s Instruction.Nos 450

M&L Making coving of 50mm X 50mm at all the flat & vertical junction using Fosroc Renderoc S Single component, shrinkage compensated, fiber reinforced, thixotropic cementitious mortar, to achieves a minimum compressive strength of 20 MPa in 1day and 55 MPa in 28days when tested as per EN 12190 and capable of applying 50mm thickness in single layer of approved product finished flush with existing surface.

M&L for water proofing teatment by using water proofing membrane as specified herein after, supply and application of single-component, Pitch free seamless roller/spray applied Nito proof 600PF or equivalent product of Asian paints, M/S MC Bauchemic /CIPY/SIKA/Pidilite Dr Fixit/ Thermax/ STP applied at average minimum DFT of 1.3 mm above primed surface with Nitoproof WB Primer or equivalent product of Asian paints, M/S MC Bauchemic /CIPY/ SIKA/ Pidilite Dr Fixit/ Thermax/ STP It shall possess the following properties: Solids by Volume: 85%, Tensile Strength ASTM D412: >1.9 MPa, Tear resistance ASTM D624C: 15(N/mm), Elongation ASTM D-412: >400%,Adhesion in-peel test ASTM C836 (N): > 50N Note: 1. Providing a non-woven geotextile fabric of 200GSM over the cured waterproofing membrane before going for a protective layer. 2. Fill the sunken with water and check for dampness and seepage . All pipes passing through walls of sunken floor shall be laid before water proofing treatment is carried out . One No 50 mm dia, 35 mm long medium grade GI pipe with wire gauge on inside mouth shall be provided to each sunken portion.Cost of pipe with including of quoted rate , no extra cost will paid. 3. The work shall be carried out complete as per manufacture's specifications and application methodology. Execution to be done with authorized trained / skilled applicator with prior experience of more than 5 years in applying similar system and as per manufacturer technical guidelines laid by manufacturer.

Remove of plants/ bushes with roots from wall and concrete surfaces and applying herbicide 2,4-Dichlorophenoxyacetic acid as require and make the disturbed area with PCC (1:2:4), type B0 (Using 12.5 mm graded stone aggregate) or Cement morter 1:4 all as directed by Engr in charge.

M & L for PCC type E2 ,1:5:10 (Using 40 mm graded stone aggregate) as in foundation filling and mass concrete

S&F glass dividing strips, 3mm thick and 38mm wide inserted in position to confirm to design

M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding. 0.18 sqm on vertical surfaces for skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar (1:4) for backing of tiles.

M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding. 0.11 sqm, in floors etc. set and jointed in neat cement slurry over and including a 15 mm thick screed bed of cement mortar (1:6) and pointed with white or Coloured cement to match.

M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding. 0.11 sqm on vertical surfaces for skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar (1:4) for backing of tiles.

M & L for preparing new plastered surfaces and applying two coat of white wash on surfaces of ceilings.

M & L for preparing new plastered surfaces and applying Two coats of oil bound distemper over a coat of alkali resistant primer on surfaces of walls.

M&L for applying a coat of blown industrial bitumen of grade 85/25 or 90/15 applied hot to concrete, wall surfaces @ 1.2Kg/Sqm or as required including cleaning the surfaces all as directed by Engr in charge.

M&L for applying two coat of blown bitumen of grade 85/25 or 90/15 applied hot to concrete, wall surfaces @ 1.5Kg/Sqm per coat or as required as directed by Engr in charge.

Taking down rain water pipes including all fittings any size and pattern. upto 7th storey floors.

M&L for 150 mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls as rainwater pipe.

S & F 75 mm dia.,PVC Bends with access door all as specified and directed

S & F 110 mm dia., PVC Bends with access door all as specified and directed

S & F 150 mm dia., PVC Bends with access doorall as specified and directed

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc l0cm girth in brick walls complete all as specified and as directed.

S&F 3-layer PP-R P o l y p r o p y l e n e random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings ie elbow, Tee, union , tank nipple, coupling etc fixed complete to walls, ceilings or in floors etc. outer diameter of Pipes in 16 mm. (Note : One PP-R union must be fixed in delivary line as direction by Engr in Charge)

S&F 3-layer PP-R P o l y p r o p y l e n e random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings ie elbow, Tee, union , etc fixed complete to walls, ceilings or in floors etc. outer diameter of Pipes in 25 mm. (Note : One PP-R union must be fixed in delivary line as direction by Engr in Charge)

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified, outer diameter of Pipes in 16 mm

S&F in repair Brass Elbow for CPVC pipes SDR 11 & Plain CPVC SDR 11 with special fittings for hot water only

S&F in repair Brass Tee for CPVC pipes SDR 11 & Plain CPVC SDR 11 with special fittings hot water only

S/F in repairs PP-R Gate valves (brass insert) of 25 mm dia with iron wheel head screwed both ends for iron pipe and fixed etc .

S & F in repair Vitreous china wash down water closet (Pedestal pattern, ETWC), white (including fixing bolts, Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as specified and directed.

S&F in repairs PVC Flushing cistern 10 Ltr capacity valveless syphonic action type low level, white, with inlet ,ball valve float and handle including brackets and flush pipe all as specified and directed.

S&F in repairs plastic water closet seat cover, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device.

Taking down carefully copper/aluminium point wiring (light fan socket or power) complete including fittings & fixtures such as switches, ceiling rose, pendants, regulators, sockets, ceiling roses,pendants, regulators, light fittings etc. Removing materials to store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified & as directed.

Point wiring complete with 1100volts grade, single core, PVC insulated FRLS cable multi-stranded copper conductor of size 1.5 sqmm nominal area, drawn through and including PVC Casing Caping of suitable size, with all necessary fittings and accessories fixed in walls/ ceiling with one run neutral and one run of single core cable of same description above but green colour in continous earthing wire connected to common earth dolly including PVC junction / mounting boxes on / in the wall / ceiling for piano switches/ switch socket combination/ fan regulators etc and GI junction box duly covered with 3mm thick hylam sheet for the following, complete all as specified and directed. :-

One light/ fan point controlled by one single pole 5 Amps switch

One switch socket out let point 5 Amps on independent board

All as per item No 137 here in before but for PVC insulated FRLS copper conductor of size 2.5 sqmm for switch socket multipurpose 15 Amps including provision of 2.5 Sq mm PVC insulated FRLS copper conductor cable as earth continuity conductor on independent board

All as per item No 137 here in before but for PVC insulated FRLS copper conductor of size 4.0 sqmm for switch socket multipurpose 15 Amps including provision of 4.0 Sq mm PVC insulated FRLS copper conductor cable as earth continuity conductor on independent board

S & F in repair PVC ceiling rose 65 x 50 mm surface type with 3 terminals, complete all as specified and directed.

S & F in repair Piano type switch single pole 5 Amps one way 230 volts, complete all as specified and directed.

S & F in repair Socket outlet 2 in 1, 3 pin, 6 Amps 230 volts, complete all as specified and directed.

S & F in repair Switch socket combination 2in 1, 3 pin 5 amps multi purpose flush type universal, with indicator, complete all as specified and directed.

S & F in repair Switch socket combination 5 in 1, 3 pin 5 and 16 amps multi purpose flush type universal, with indicator complete all as specified and directed.

Sub main wiring with Two single core PVC insulated FRLS cable with copper conductor multistranded 1100 volts grade 2.50 sqmm in and including non-metallic rigid PVC casing and capping and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 2.50 sqmm PVC insulated FRLS multistranded copper earth continuity conductor and connecting to main earth dolly including taking down complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC casing capping and two run of copper conductor together taken as one length for measuring unit length.

Taking down Exhaust fans, of any size or any capacity 250/300/350/400 mm sweep dismantaling blades & refixing of the same including and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed. Note:- (i) Servicing & overhauling, rewinding,Painting & replacement of defective spare part, connecting wire etc shall be measured & paid separately

Rewinding of Exhaust fan 250/300/350/400 mm sweep dismantling the ceiling fan, removing the burnt winding, cleaning slot, replacement of defective nut bolts washer etc and rewinding with using appropriate size of super enamelled copper winding wire thermal class-E, including varnishing all as specified and directed.

Servicing & Overhauling only of Exhaust fan 250/300/350/400 mm sweep at site by oiling/ greasing to reduce the noice of the fans and connecting the same complete all as specified and as directed.

Supply and fixing of in repairs Exhaust Fan capacitors 2.5 mfd for fans all as specified and directed

Material & Labour for Taking down & Refixing only geyser 50/25 ltrs capacity after repairs in new position including drilling holes on wall ,fixing four Nos anchor bolts,nuts and washers and connecting to the water and electric connections and testing complete all as directed.

Servicing of storage type electric water heater (geyser) of capacity 15 /25 litres comprising of the following works: - (i) Taking down geysers from existing position after disconnecting all electrical & water supply connection. (ii) Opening / dismantling & cleaning of all parts & checking for its serviceability. (iii) Cleaning / descaling of thermostat & inner tank with descaling solution & water leakage testing of tank & rectification of leakage. (iv) Checking of pressure reducing valves & non return valve etc. to ensures free movement / smooth operation of these components. (v) Checking of overflow / vent pipes and removing blockages / obstructions if any. (v) Reassembling the geyser, replacement of minor spare part such as nut, bolt, screw, rubber packing etc & refixing in same position, reconnecting with electric & water supply connection complete all as specified and as directed.

Taking down Wall Mounted fans from walls , dismantaling blades & refixing of the same including and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed. Note:- (i) Servicing & overhauling, rewinding,Painting & replacement of defective spare part, connecting wire etc shall be measured & paid separately

Rewinding of Wall mounted fan of any sweep dismantling the ceiling fan, removing the burnt winding, cleaning slot, replacement of defective nut bolts washer etc and rewinding with using appropriate size of super enamelled copper winding wire thermal class-E, including varnishing all as specified and directed.

Taking down ceiling fans from ceiling, dismantaling blades & refixing of the same including and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed. Note:- (i) Servicing & overhauling, rewinding,Painting & replacement of defective spare part, connecting wire etc shall be measured & paid separately

Rewinding of ceiling fan1200/1400mm sweep dismantling the ceiling fan, removing the burnt winding, cleaning slot, replacement of defective nut bolts washer etc and rewinding with using appropriate size of super enamelled copper winding wire thermal class-E, including varnishing all as specified and directed.

Servicing & Overhauling only of ceiling fan at site by oiling/ greasing to reduce the noice of the fans and connecting the same complete all as specified and as directed.

Supply and fixing of in repairs capacitors 1.5 mfd for fans all as specified and directed

Supply &fixing of in repairs stepped type electronic fan regulator flush type 300 watts with 5 step speed control for fans any sweep 1200 mm/1400 mm fixed as in repair complete all as specified and directed

Supply and fixing in repair LED lights fitting 4 feet, 1 x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Removing excavated material exc 500m but not exc 1.5km & depositing where all as specified and directed Engr-in-Charge

EURO ENTERPRISES

SRI GANESH ENTERPRISES