PROVISION OF RCC RETAINING WALL, BOUNDARY WALL, OTHER MISC WORKS, PLASTERING AND OTHER ASSOCIATED WORKS IN NAVIKS MD ACCN NO P-43 TO P-91 AT CGRA KANKANADY MANGALORE

Amount

Demolition of brick/stone masonry built in cement mortar in any position complete all as specified and directed.

Excavating in trenches exc 1.5 m wide and n exc 10 sq m on plan and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. and getting out in hard dense soil all as specified and directed.

All as per Item 2.00 above but exc 1.50m and n.exc 3.00m in depth and getting out in hard and dense soil complete as specified and directed

Excavation over areas for foundation n.exc 1.50m deep and getting out in hard and dense soil all as specified and directed.

All as per Item 4.00 above but exc 1.50m and n.exc 3.00m deep and getting out in hard and dense soil complete as specified and directed

Returning filling in including spreading levelling watering in layers n.exc 25 cm in hard and dense soil all as specified and directed.

Removing excavated material (soil) to a distance exc 250m and n.exc 500 m and deposited where directed at a level n.exc 1.5m above the starting point all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation / mass concrete for wall and post struts all as specified and directed.

M&L Mild steel TMT bars 10mm dia & over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M&L Mild steel TMT bars 5mm dia and over up to and including 10mm dia & over cut to length, bent to shape required including cranking, bending spirally for hooping for coloumns,hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed as in stirrups, spaces and binders all as specified and directed.

M&L RCC M-30 design mix concrete using 20mm graded aggregate for coloumns, Pillars, Posts etc all as specified and as directed

M&L RCC M-30 design mix using 20mm graded stone aggregate as in beams, cantilevers, bressumers, lintels over 1.5 mtrs span all as specified and directed.

M&L RCC M-30 design mix using 20mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and directed.

M&L RCC M-30 design mix using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

M & L use and waste of form work to sides of pillars,posts, struts, piers, coloumns and stanchions including for fair finished surfaces all as specified and directed.

M & L use and waste of form work to sides and soffits of floor or roof beam, beam haunchings girders, bressumers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams all as specified and directed.

M & L use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter all as specified and directed.

M & L use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and directed.

M&L for dressed laterite stone masonry, well bonded, bedded and solidly hearted built in CM 1:6 all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 mixed with water proofing compound @ 3% by weight of cement finish the surfaces even and fair all as specified and directed. Note: WPC shall be measured and paid seperately

M&L Preparation of new plaster surfaces and applying two coats of cement based paint over a coat of primer all as specified and directed.

M & L for rendering 15 mm thick in CM 1:6 on brick works/ concrete surfaces finished even and smooth with out using extra cement complete all as specified and directed.

M & L for preparing new plastered surfaces of wall and applying two coats of Oil emulsion distemper over a coat of primer all as specified and directed.

M & L for 100mm thick Cement concrete type D-2 (1:4:8) 40mm graded stone aggregate, as in sub base complete all as specified and as directed.

M&L 25mm thick cement concrete type B-0 (using 12.50mm graded crushed stone aggregate) as in floors finished rough to receive floor finishes complete all as specified and directed.

M & L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm screed bed 1:4 complete all as specified and as directed

M & L for Glazed ceramic tiles on vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick backing plaster in cement mortar 1:4 complete all as specifed .

Taking down chowkats or frames n exc 1.5 sqm each (without taking off shutters from the frames) complete all as specified & as directed.

Taking down chowkats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutters from the frames) complete all as specified & as directed.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Supply and fixing 24 mm thick factory made PVC door shutters to existing door frames made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and jointed at the corners by means of M.S. galvanized/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer- in-charge. (For W.C. and bathroom door shutter).

S&F factory made PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour, PVC sheet reinforced with MS square tube complete all as specified.

S&F factory made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:) with wood free EPS, with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified .

S&F 125mm Butt hinges, heavy weight, extruded with galvanised mild steel hinge pin, anodised and fixed complete all as specified .

M&L for 150mm size aluminium handle (ISI Marked) cast type anodized, fixed complete all as specified .

S&F 300mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

M & L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer?in-charge.

S&F in repairs looking mirror of size 600x450mm, 5mm thick bevelled edge mounted on 6mm thick plywood including fixing with screws and cup washers all as specified

S&F in repar PVC valveless, syphonic action type, flushing cistern 10ltrs capacity, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32 mm dia. PVC flushing pipe, complete all as specified.

S & F in repairs Pillar taps fancy type 15 mm bore cast copper alloy, with capstain heads, chromium platedscrewed down high pressure, with or without lettered "Hot" of "Cold" with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified.

S & F in repairs for Bib taps fancy type, CP for iron pipe and fixed 15 mm bore complete all as specified.

S&F in repair Stop valves cast copper alloy 15 mm dia, fancy type, chromium plated, screwed down, high pressure, with crutch handle screwed both ends for iron pipe or for unions all as specified and directed.

S&F in repairs PVC connection 15 mm size with PTMT nuts of lengths 450 mm, complete all as specified.

S&F in repair PVC flexible waste pipe 32/40mm dia for basin/kitchen sink all as specified and directed.

S&F in repair vitreous china wash basin, white, flat back ,size 630x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets including cutting for and pinning in ends of brackets or erecting stand but exclusive of 32mm dia waste pipe complete all as specified and as directed.

S&F in repairs, vitreous China wash down water closet pan (pedestal pattern), white , including connection to outgoing drain and flushing pipe, anti syphonic pipe with seat and cover, mild steel chromium plated hinging device complete but excluding flushing cistern including making good damaged/disturbed surfaces complete all as specified and directed.

S & F in repairs health faucet CP(hand shower type) with shut off valve (thumb or fush button type) to allow controlled and continuous flow of water with flexible polythene pipe of adequate length and with wall mounted pedestal for hanging faucet including taking down of old one.

S&F PVC(SWR) branch piece (single 'Y') with door suitable for 110mm bore pipes all as directed in repairs

M & L for PVC Pipe 110mm bore drain pipes laid in trenches and jointed as specified

S& F PVC SWR multi floor trap 75mm dia complete all as specified.

M&L PVC (SWR) floor trap, 75 mm dia., plain with grating including jointing with solvent cement, complete all as specified.

Dismantling water tanks and removing to store exc 250 but n exc 500 ltrs complete all as specified and as directed.

S&F 500 Ltrs capacity rotational moulded polythene water storage tanks (cylindercal vertical with closed top ) hoisted and fixed in poisition all as specifid in SSR Part-I.

Supplying and laying of 20mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and as directed including taking down existing steel tubing.

Supplying and laying of 25mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and as directed including taking down existing steel tubing.

S&F and repair 20mm dia float valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe (Minimum weight 210 gms) complete all as specified & as directed.

M &L for water proofing treatment over and including 5mm thick plastering in CM 1:3 and applying oil based bitumen primer conforming to IS 3384-1986 at 0.20 kg/Sqm on prepared surface and applying of one coat of blown grade hot bitumen 85/25 conforming to IS 702 @ 1.20 kg / sqm and applying roof treatment with APP modified waterproofing membrane weighing not less than 3kg/sqm, reinforced with non woven polyster matt weighing not less than 160 gm/sqm having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 650N/Sqm cm, tearing strength of 180N(Minimum), applied by torch-on application including minimum 10 cm over lap and 15 cm end lap and applying of one coat of blown grade hot bitumen 85/25 conforming to IS 702 @ 1.20 kg / sqm over the membrane and then applying solar reflective bituminous aluminium paint for thermal insulation @ 0.10 kg/sqm complete all as specified and directed.

S&F 450mm dia RCC pipes class NP2 laid & jointed complete with collars all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in concrete bed to drain pipes inlcuding packing under and haunching against the sides of pipes with concrete after laid and tested for 450mm bore pipe all as specified and directed.

M & L for rendering 5mm thick in CM 1:3 on ceiling surfaces and finished even and smooth without using extra cement all as specified and directed.

M & L for preparation of newly plastered ceiling surfaces and applying three coats of white wash all as specified and directed.

Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided for RCC pillers all as specified and directed.

M&L RCC M-30 design mix using 20mm graded stone aggregate as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses

M & L for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter all as specified .

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified..

Supply and fix Joist , channel, angle, or tee sections fixed independently, as in `Y' section/ swan neck etc without connecting plates, etc. (cut to ordinary lengths i.e within 20mm of the length indicated) grade Fe-410(Gde E-250) complete all as specified.

M&L preparation of new steel surfaces of any description over 10cm girth or width and applying two coats of synthetic enamel paint over a coat of primer all as specified

M & L Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

Supply and fix concertinal coil of 700mm outer dia made out of 2.60mm dia spring steel wire 230 gm (min) dipped with corrosion preventive fluid (rusilo 901) of castrol make including white colouur, each coil having in 50 turns (circles) and an average weight not less than 8.57 kg (plus or minus 5%) including hangle and spike at both ends of coil errected in position on top of mild steel angle by fixing with MS rod for securing including necessary welding/clipping to MS section etc complete all as specified and directed.

Taking down cement plaster on brick walls including racking out joints haking for keys scrubbing down with water etc complete all as specified.

Supply only integral water proofing compound

Demolition of cement concrete in ground floors and paving n. exc 15cm thickness (below or above ground level) including plinth protection etc complete as directed

M & L preparation of finishing walls with Acrylic Smooth exterior paint of required shade on New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm with 2 to 3mm thick wall care putty on walls etc all as specified and directed.

M & L for preparing old surface of ceiling by brooming down or steel wire brushing, scraping down moss and efflorescent salt etc and applying one coat of white wash all as specified and directed.

M & L for preparing old treated wooden surface of any description over 10cm width or girth and applying one coat of Synthetic enamal paint all as specified and directed.

M & L for preparing old surface of ceiling by brooming down or steel wire brushing, scraping down moss and efflorescent salt etc and applying one coat of OBD all as specified and directed.

M & L for preparing old treated steel surface of any description over 10cm width or girth and applying one coat of Synthetic enamal paint all as specified and directed.

M & L for preparing old surface of wall by brooming down or steel wire brushing, scraping down moss and efflorescent salt etc and applying one coat of cement base paint all as specified and directed.

M & L for complete removal of existing treatment of wall by brooming down or steel wire brushing, scraping down moss and efflorescent salt etc and applying two coats of Oil emulsion distemper including one coat of primer

M & L for preparing old surface of wall by brooming down or steel wire brushing, scraping down moss and efflorescent salt etc and applying one coat of arcylic exterior emulsion antifungal paint (upto 4th floor)

M & L for Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high at any height including required staging/ scaffolding etc

Taking down Shutters of any description but exc 1 sq. m and n exc 2 sq. m each

S & F powder coating (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators including grill with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F for glazed and skelton shutters 30mm thick 2nd class hard wood, open rebated and prepared to receive glass, guage etc, (with sash bars) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc complete all as specified and as directed.

S&F aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of apeture 1.40mm and fixed with aluminium wire stapples complete all as specified and directed

M&L preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L plain WPC door frawme 100x50 Decorative including all fixing arrangements/accessories for fixing WPC shutter providing Brand Factory Made 30mm thick 100% solid WPC (Wood polymer Composite) Solid Plain flush Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade) Calcium Carbonate and natural Fibers (Wood Powders/rice husk/wheat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cbn having good screw holding capacity (Screw Withdrawal strength of 2000N (Face) & 1100 N (Edge)., Minimimum Compressive Strengh of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with property of being Termite/Borer Fee Water/Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full doby threaded star headed counter sunk SS Screws. All as per direction of Engineer-in-Charge.

M&L plain WPC shutter 30mm thick with all fixing accessoried all as directed providing Brand Factory Made 30mm thick 100% solid WPC (Wood polymer Composite) Solid Plain flush Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade) Calcium Carbonate and natural Fibers (Wood Powders/rice husk/wheat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cbn having good screw holding capacity (Screw Withdrawal strength of 2000N (Face) & 1100 N (Edge)., Minimimum Compressive Strengh of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with property of being Termite/Borer Fee Water/Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full doby threaded star headed counter sunk SS Screws. All ass per direction of Engineer-in-Charge.

S&F in repair 100mm butt hinges, medium weight, cold rolled mild steel.

S&F floor door stopper of.brass body and tongue with hard drawn steel spring overall length of cover plate 150 mm and fixed complete all as specified and directed

Taking down and re-fixing of shutters in same opening but exc 1 sqm and n exc 2 sqm each complete all as specified and as directed.

S & Fixed in repair aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of apeture 1.40mm and fixed with aluminium wire stapples complete all as specified and directed

Hacking out old broken glass (any thickness, size quality or description) from wooden frames glazed with putty or fixed with beads complete all as specified and as directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in sqm n exc 0.5 sqm in each pane complete all as specified & directed.

M & L for cement mortor 1:6 Forming jambs , etc to openings (to foregoing item) , including cutting, toothing and properly bonding into old work, also facing , jointing and pointing to match existing work, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M & L Virified Ceramic tiles dark shade double charged/ultracharged of 10 mm thick (square/rectangular) polished, area of each tiles exc 0.42 sqm but n exc 1.00 Sqm in floors, including boddering etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 20mm screed bed 1:4 complete all as specified and as directed.

All as per Item No 101.00 above but as in skirting over 10 mm thick rendering in CM (1:4) all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth all as directed.

S & F in repair brass cromium plated shower rose 125mm with or without swivel joints any size including fixing to steel pipe or union complete all as specified and directed by Engr-in-Charge.

S&F in repair Stop valves cast copper alloy 15 mm dia, chromium plated with long shank and cup (concealed type) complete all as specified.

S&F cabinet mirror size 332mmx146mmx430mm with all fittingcomplete all as specified and directed.

S & F in repair Waste coupling bore dia of 40mm to discharge pipe PTMT (half or full threaded) . (Minimum weight 32mm?45gms/40mm-60 gm) for sin all as specified and directed. .

S &F in repair Brass chromium plated bottle traps 32mm bore for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed all as specified and directed.

S & Fixed in repairs CP Soap dish size 160 x 160x90mm fixed to plugs with CP brass screws all as specified and directed.

S &F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges all as specified and directed.

S&F Gunmetal globe or gate valve 25 mm dia iron wheel head screwed both ends for PVC pipes incl taking out old all as specified and directed.

S & F Grating square (SLIT) 150mm of PTMT. (Minimum weight 100 gms) all as specified

S & F in repairs 32mm dia Harrison rails,stainless steel fancy type with fixing brackets, stops, rollers etc complete all as specified & directed.

S&F 1000 Ltrs capacity rotational moulded polythene water storage tanks three layer (cylindercal vertical with closed top ) hoisted and fixed in poisition all as specified in SSR Part-I all as specified and directed.

M&L 100mm thick PCC 1:3:6 Mix type C2 as in plinth protection and in path surface to be finished without using extra cement complete all as specified and as directed.

M &L Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set with grey cement and pigment, jointed and pointed in neat cement slurry in floors including 20mm thick screed bed in CM 1:6 all as specified and directed.

M&L for PCC 1:2:4 type B0( using 12.5 mm graded stone aggregate) as in stages for tank, roof kerbs covering over chajjas and similar locations rounded or chamferred on edges incl necessary formwork complete all as specified & as directed by Engineer-in-Charge

S & F utensil rack (Plate rack) made out of 1 mm thick stainless steel of size 31 inch x 30 inch x 10 inch fixed to wall with chromium plated brass screw 30 to 50mm size including all internal fittings of untensil rack as per sample approved by Engineer-in-Charge and as directed.

KDR CONSTRUCTION (BID ID -3387031)