Special repair of slab replacement

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing (HSR 8.5) (b) in Cement

Dismantling Concrete. reinforced cement concrete with cleaning and straightening and cutting of bars if required. [(HSR 8.6 (e)]

Demolishing mud phaska in tile terracing (HSR 8.8(g)

Removing door and windows (wooden and steel) with chowkats by making recesses in walls when the wallis not to be dismantled (HSR 8.18) (i) Door

(ii) Windows

(iii) Ventilators

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centering and shuttering, laid in position, complete in all respect. [HSR. 10.82 + 10.95 (a)]. First Storey

Second Storey

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (Straight and curved) beams, girders, stairs, columns, (square or rectangular) battens and lintels etc. excluding steel reinforcement but including centering and shuttering, laid in position complete in all respects. [HSR. 10.86 + 10.95 (a)] First Storey

Second Storey

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in fasicas, parapets and other thin vertical sections, not covered by item no. 10.82, 10.86 to 10.88 not exceeding 10 cm thickness excluding steel reinforcement but including centering and shuttering, laid in position, complete in all respects. [HSR. 10.89 + 10.95 (a)] Second Storey

Third Storey

First class brick work laid in cement sand mortar 1:6 in 1st storey upto 4 metre above plinth level. (HSR 11.7) First Storey

Second Storey

Terracing consisting of tiles 22.86 cm x 11.43 Cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13) Second Storey

Third Storey

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16. (HSR 13.50)

Supplying & fixing in position G.I. pipe class 'B' spouts in chajjas and cantilevers. (e) 50mm i/d G.I. pipe. [HSR 13.55(e) ].

Bottom khurra on ground 1.2 m x 0.6m consisting of brick on edge laid in cement mortar 1:3 over 75mm C:C 1:8:16 including 12mm thick cement plaster 1:3. (HSR 13.57)

Cement Concrete 1:2:4 gola 10cm x 10cm quadrant along junction of roof with parapet wall finished smooth, where specified. (HSR 13.64).

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.89]. Note:- The Agency to whom the work is allotted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (b) 150 mm dia PVC pipe 6 kg. pressure.

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.90]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (b) 150 mm dia PVC Bend.

Screed of 50 mm thick cement concrete 1:8:16 to be laid below the topping. (HSR 14.4) Second Storey

Fixing & laying of Marble stone flooring 17 mm and above thick slab including matching grains of marble laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of marbl including rubbing and polishing. (Excluding the cost of Marble, Marble will be supplied by the Department). (HSR 14.49). First Storey

Second Storey

Kotah stone flooring minimum 25 mm thick in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. First Storey

Second Storey

Kotah stone 20 mm thick in skirting risers of steps, dados and wall facing (lining) and pillars laid on 12 mm thick cement coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, dowels and pins etc. (HSR 14.66). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. First Storey

Second Storey

12mm thick cement plaster on walls (1:6). (HSR 15.7) First Storey

Second Storey

15mm Thick Cement Plaster 1:6 on the rough side of single or half brick wall. (HSR 15.12) Second Storey

Third Storey

10mm thick cement plaster 1:4 under side of ceiling. (HSR 15.52) First Storey

Second Storey

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. Painting on wooden surfaces etc. (HSR 16.1) (Through Rate)

Providing and Applying pink primer or aluminum priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2). (Through Rate)

Providing and Applying Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3). (Through Rate)

Providing and Applying priming coat with metal primer on new steel or iron work including preparation of surface. Painting on mettalic Surfaces etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.9). (Through Rate)

Providing and Applying Painting two coats excluding priming coat with ready mixed paint for matelic sufraces in all shades on new steel or iron work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.17). (Through Rate)

Providing and applying White Washing. (Three Coats). (HSR 16.48) (Through Rate)

Providing and Applying Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58). (Through Rate)

Providing and Applying two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)]. (Through Rate)

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81). (Through Rate)

Providing & fixing 150 mm hasps and staples with necessary screws, etc. complete Aluminium. (Powder coated fittings will be supplied by the deptt. Instead of Aluminium fittings.) [HSR 17.78 (b)].

Providing and fixing helical door spring 150mm (superior quality) including necessary screws, complete HSR 17.79.) (b) Iron

Supplying and fixing hydraulic door closer ISI mark with necessary screws etc. complete ( HSR 17.82 (b ) (b) ISI designation No. II (size of door 701 mm to 850 mm)

Providing and fixing 50 mm cup board or ward robe knob- (b) aluminium. [HSR 17.84 (b)].

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock Champ; Champ only. (non coniferous timber other teak, confirming to I.S. specification No. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood nd including cost of iron hinges, screw, chock/cleats, stops nails etc. complete in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). [HSR 17.90 (a) - Note 1 under 17.18]. (a) 30 mm thick.

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock & Champ only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. [HSR 17.92 (i) - Note 1 under 17.18] (i) 30 mm thick.

Factory manufactured solid flush door shutters, with block board core as per I.S. No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II , fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position (Note reputed make such as Duro, Green, Kitply will be used as per approved by Engineer-in Charge) [HSR 17.93) - Note 1 under 17.18] Note:- The agency to whom the work is alloted will have to produce original bill / voucher for all quantity in token of proof of purchase of material (iii) 35 mm thick.

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, grating frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12).

Steel reinforcement TMT bars FE-500 EQR / FE-500 D grade or mor for RCC work, where not included in the complete rate of RCC including bending, straightening, bending, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc and & placing in the position complete in all respect for all heights / depths /storeys / basements etc. (Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps, wastage, overlaps, coupling, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement) . (HSR 18.22).

Supply and fixing Glass panes including special metal sash putty of approved make. [HSR 18.30 ] (b) glass panes 4 mm thick, exceeding 40 sq. dm areas.

Pressed steel sheet frames (chowkhats) consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts) iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. [HSR 18.34]. (a) door and window frame Size of 89 mm x 59 mm with 40 mm wide signel rebate.

(c) door and window frame size 127 mm x 50 mm with 40 mm wide double rebate.

Providing ISI marked aluminium Tower Bolts with nuts & Screws etc. complete (NS) Size 100 mm x 10mm

Size 150 mm x 10mm

Size 200 mm x 10mm

Providing ISI marked aluminium Sliding Door Bolts with nuts & Screws etc. complete (NS) Size 300 mm x 16mm

Providing ISI marked aluminium Door Handles with nuts & Screws etc. complete (NS) Size 100 mm x 150 mm x 30 mm

Size 150 mm x 200 mm x 35 mm

Providing ISI marked aluminium butt hings with nuts & Screws etc. complete (NS) Size 100 mm x 31.75 mm x 11 mm

Size 125 mm x 31.75 mm x 11 mm

Recovery items: Bidder have to quoted rates for recovery items at least or more than reserve price. The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Note:- The reserve amount is minimum amount to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purpose in case the agency quotes lesser than reserve price as under:- (i) Quantity of Good Bricks @ Rs. 4.50/- Each

(ii) Quantity of Brick Bats @ Rs. 450/- Cum

(iii) Credit of Steel Rusted @ Rs. 1800/- Qtls

(iv) Doors @ Rs. 500/- Each

(v) Window @ Rs. 300/- Each

(vi) Ventilators @ Rs. 200/- Each