BMSICL/Infra/11/2026 GR-17 Construction of 11 APHC at Block-Sadar, Akbarpur, Kawakol, Meskaur, Nardiganj, Narhat and Rajauli in District-Nawada.

Construction of 11 APHC at Block-Sadar, Akbarpur, Kawakol, Meskaur, Nardiganj, Narhat and Rajauli in District-Nawada.

DEMOLITION

Earth Work

Design Mix RCC

Nominal RCC

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, blackfinished reinforced with non- woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/ sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemicalparameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5 cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking TGrid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking TGrid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.

Horticultre and landscapping

2.29 (DSR H&L 2018)

2.30.1 (DSR H&L 2018)

DSR H&L 7.74

Carriage of materials

Difference Cost of materials :-

PHE ITEMS

Concealed work, including cutting chases and making good the walls etc.

Tubewell and Rainwater Harvesting

Rain water harvesting

Fire Fighting Work

FIRE PUMPS - ELECTRICAL

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 (b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads.

a) Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Drive Pump)Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. b) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.

c) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plastered and with anti vibration pads.

ELECT. DSR 2018 / 16.7.4

ELECT. DSR 2018 / 16.7.3

ELECT. DSR 2016 / 16.7.1

ELECT. DSR 2018 / 16.8

Threaded joint upto 50mm diameter pipe.

Welded joint above 50mm diameter pipe.

FIRE ELECTRICAL WORKS

FIRE ELECTRICAL WORKS (DSR 2018)

ELECT. DSR 2018 5.4

ELECT. DSR 2018 / 16.7.4

ELECT. DSR 2018 / 16.11.2

ELECT. DSR 2018 / 16.11.1

ELECT. DSR 2018 / 16.8

ELECTRICAL WORK

Supplying and fixing metal/ PVC box of following sizes ( nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in the front including painting etc. as required.

Supplying & fixing of following size medium class PVC conduit along with accessories in surface/ recess including cutting of wall and making good the same in case of recessed conduit as required.

Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular fitting in recess etc. as required.

Supplying and fixing cable end box ( Loose wire box , IP 43) suitable for following sheet steel M.C.B. Distribution board, on surface/ recess, complete with testing commissioning etc. as required

Supplying and fixing following ways TPN vertical Loadline distribution board suitable for upto 160 Amp four pole MCCB as incomer and MCBs as outgoing in surface/ recess, ,inclusive of tinned copper busbar, common neutral link , earth bar, din bar , for mounting MCB's etc. as required, (but without MCCB & MCB's )

Supplying and fixing of following rating electrical items in the existing Verticle DB as incomer including drilling holes in cubicle panel making connections etc. as required .

Supplying and fixing of following rating C series MCB suitable for inductive and other loads of following poles in the existing MCB DB complete witth connections ,testing and commissioning etc. as required .

Supplying and fixing of following rating electrical items in the existing cubical panel board including drilling holes in cubicle panel making connections etc. as required .

Incomings:-

(b) Out going

Electrical Fitting

Supplying and fixing following types lamp in existing electrical fitting/ fixture etc as required.

Supply of PVC insulated PVC sheathed aluminium conductor armoured under ground cable of graded 1.1 KV for working voltage upto 1100 volts conforming to ISI 1554 (Part-I) of 1964 with upto date amendment as detailed below.

Laying of one number PVC insulated and PVC sheathed/ XLE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushionig, protective covering and refilling the trench etc. as required.

Laying of one number additional PVC insulated and PVC sheathed/ XLE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horzintal formation including excavation, sand cushionig, protective covering and refilling the trench etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed aluminium conductor cable of1.1 KV grade of following size on surface etc. as required.

Providing and laying following size NP2 (Non pressure) RCC pipe complete with RCC collar etc. as required .

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as reguired.

Supplying & embedding of following dia G.I. pipe (medium class) in pole collor / foundation (during casting ) for cable entry including bending the pipe to the required shape complete etc. as required.

Total

Construction of 11 APHC at Block-Sadar, Akbarpur, Kawakol, Meskaur, Nardiganj, Narhat and Rajauli in District-Nawada.

Name of Firm

Address of Firm

MP PWD 1.2

For OT Areas

For ICU

For Wall

Self levelling

Hospital Curtain tracks & I.V. tree System

Manual Sliding Door with LEAD protections for X-ray of dimensions(WxH) 1000x2100mm having window, double glazing centrally in the door leaf 400 x 600mm

OT DOOR

Automatic Scrub Sink

PHE ITEMS

Submersible pump

U.P.V.C. PIPE

ANALYSIS

P.V.C. FITTINGS

SECTION- V

Supply, Fabrication, installation, testing and commisioning of Fully automatic effluent treatment plant with effluent handling capacity 15 m3 per day. The entire plant will be constructed in MSEP. The ETP shall be designed as water retaining structures, with necessary chemical dosing as required by the manufacturer's design. All the equipment, piping, pumps, air blowers and electrical panel to be housed in the ETP skid including M.S. puddle flange (Galvanised), inlet, outlet, overflow, vent, moving ladders & railing. The Plant shall be complete with a central Electrical Power and Control panel fully pre/site wired and with all power and control cables to all pumps and equipment including all instrumentation, level and other controls. The cost will also include any consequential civil work including making foundations for the structure, pumps, blowers etc.

Design to take consideration of same.

Daily average flow : 10 M3/Day

BOD5 : 250 - 600 mg/l

S. Solids : 200 - 650 Mg/l

COD : 600 - 1200 mg/l

Oil & Grease : 50-140 mg/L

Effluent discharge standard after treatment :-

S. Solids : Less than 100 mg/l

COD : Less than 150 mg/l

Oil & Grease : Less than 5 mg/l

BOD : <50 mg/l

The ETP shall consist of following units but not limited to these unit as may be required by the manufacturer's design. MS PVC coated rungs in all tanks & Platform for maintenance etc. complete as required.

SS Perforated basket screen having provision for chain lifting arrangement etc. complete as required.

Constructing Grease Trap with Belt type oil skimmer of suitable size with minimum of 500 liquid depth in MS construction with FRP lining inside including SS bucket as per detail to collect the grease.

Collection cum Equalization tank including provision for aeration will be kept to avoid any smell problems in MSEP Construction. Min. 3750 l.

Reaction tank with air diffuser and piping complete of adequate capacity. The unt shall be equipped with an agitator of slow speed with gear. The MOC of the agitator shall be SS304.Tank construction shall be in MSEP lined inside. 750 L

Primary Settling tank ( Tube Settler type), hopper bottom type with arrangement of deep well, baffle wall, scum removal arrangement, outlet launders with arrangement of lifting sludge from the bottom etc. complete as required in MSEP Construction. 1125 L

Clear Water Tank to collect the treated water with Inlet/Outlet, drain, overflow connection, vent etc. complete as required of in MSEP Min. 750 L

Sludge Holding Tank with suitable sludge disposal pump of suitable capacity with provision of air diffusion, supernatant withdrawl arrangement in MSEP Min. 1500 L

Air diffuser system with 2 nos. twin-type air blower of capacity suitable for 20 m3/day at the pressure of 0.50 kg/cm2 each including fine bubble membrane type diffusers complete with valves & air distribution grid complete as required.

PVC piping (10kg/sqcm) - For all submerged waste water piping.

MS (C Class) - For all exposed air piping and flexible braded pipe for submerged air piping.

GI (C class) for all other water piping.

Providing and fixing all instrumentation eg. Pressure guages, level controllers, sensors, rotametres for air, water etc. for making the system complete.

EQUALIZED WASTE WATER TRANSFER PUMPS :

Providing & fixing Submersible centrifugal pumps solid handling (min. 50 mm) pumps. The pumps shall be made of CI casing, CI Impellar, SS shaft & sleeve, Mechanical Seal are connected to a TEFC induction motor mounted on a common channel base frame with coupling guard, 150 mm dia pressure gauge with GM isolation cock, suitable vibration eliminator pads of approved design. Motor to be suitable for 400/440 V, 3 Phase, 50 cycles AC power supply, including all necessary piping, valves and other accessories and concrete foundation complete as required.

Capacity : 1.0 M3/hr @ Discharge Head 10 M head (1 Working + 1 Standby)

SLUDGE RECIRCULATION PUMP :

Providing & fixing Horizontal centrifugal Self-Priming pumps solid handling (min. 7 mm) pumps. The pumps shall be made of CI casing, CI Impellar, SS shaft & sleeve, Mechanical Seal are connected to a TEFC induction motor mounted on a common channel base frame with coupling guard, 150 mm dia pressure gauge with GM isolation cock, suitable vibration eliminator pads of approved design. Motor to be suitable for 400/440 V, 3 Phase, 50 cycles AC power supply, including all necessary piping, valves and other accessories and concrete foundation complete as required.

Treated Water Transfer Pumps :

Providing and fixing Horizontal centrifugal pumps. The pumps shall be made of CI casing, bronze Impellar, SS shaft & sleeve, Mechanical Seal are connected to a TEFC induction motor mounted on a common channel base frame with coupling guard, 150 mm dia pressure gauge with GM isolation cock, suitable vibration eliminator pads of approved design. Motor to be suitable for 400/440 V, 3 Phase, 50 cycles AC power supply, including all necessary piping, valves and other accessories and concrete foundation complete as required.

Capacity 1.0 M3/Hr.@ 10M head

Supplying, installing, testing & commissioning of Horizontal centrifugal non clog water pumps with CI Head & Base, bronze Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer (with by-pass) at suction. Mechanical seal, suitable vibration elimination pads of approved design, drain pipe with valve (25 dia) for the pump. The pump shall be suitable for 415±10% volts 3 phase AC supply (1 Working + 1 Standby).

Capacity : 1 m3/hr each

Head : 30 M

Test pressure : 5.5 Kg/Sq.cm

Dia : 300mm

Flow Rate : 1 m3/hr

Considering 10 M3/M2/hr filtration velocity, the diameter of MGF shoudl be 900 mm we have quored for 900 mm only

Activated Carbon Filter

Test pressure : 5.5 Kg/Sq.cm

Flow Rate : 1 m3/hr

Considering 10 M3/M2/hr filtration velocity, the diameter of ACF shoudl be 900 mm we have quored for 900 mm only

Supply, installation, testing and commissioning of filter press of Suitable Capacity with CI frame, PP plates complete with filter cloth complete with Filter press feed pump (Screw Type) – 2 No. (1 working + 1 standby) with 1 No. standby stator, interconnecting piping and poly dosing system.

Providing and fixing lime/alum/polyelectrolyte dosing system consisting of Lime/Alum/Pedosing pump (0-6 lph) with 100 l HDPE tanks including all piping from the dozer to the reaction tank etc. complete in all respects.

Fire Fighting Work

Fire Hose Cabinet

Providing and fixing angle iron (40 mm x 40 mm x 5 mm) MS door frame 900x2100 door capable of accommodating fire hose reel, landing valve, hose pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) Cost of fire extinguishers not included in item rate. (Liasioing with civil contractor for making 900x600x2100 Recessed type mansoary box (by civil contractor).

TAC approved 1.6mm thick M.S. fire hose cabinet (750x600x250mm) made out of 16 gauge M.S. sheet capable of accommodating landing valve, hose pipes, fittings & accessories. The box shall have a front glass door with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) - for external and roof hydrant.

63mm dia single outlet GM landing valve IS marked with suitable size bolts, nuts, washers and gaskets. Landing valve shall be TAC Approved Make.

63mm dia twin outlet GM landing valve IS marked with suitable size bolts, nuts, washers and gaskets. Landing valve shall be TAC Approved Make.

First aid hose reel with 25 mm dia, 30 m long rubber hose, ball valve, piping and GM nozzle

63mm reinforced rubber hoses (RRL) with male and female GM coupling, IS marked- 15 m long

Fire Axe

FIRE EXTINGUSHER (NON SCHEDULED ITEMS)

Capacity 4.5 kg

Capacity 6 Kg.

Providing and fixing mechanical foam type Trolley Mounted Fire Extinguisher of bearing to IS:10568/IS13385/IS13386 with dis

Capacity 50 Lit.

Providing and fixing Carbon Dioxide Type Trolley Mounted Fire Extinguisher of as per IS: 2878 with discharge time of 10 to 20 sec/15 to 36sec/20 to 60sec respectively.

22.5 Kg. CO2 Fire Extinguisher

EPABX

SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM

Supplying, installation, testing and commissioning of Grid interactive roof top solar photo voltaic power generation system including space frame

MEDICAL GAS PIPELINE SYSTEM

Oxygen System

Mani fold- Oxygen Manifold 6 + 6 cylinder banks complete with NRV, tail Pipes, Middle frame, Bottom Frame with CE marked,

Semi Automatic Control Panel for Oxygen- 4 bar line pressure, 400lpm as per HTM standard CE,

Emergency Oxygen Manifold- 01 + 01 Cylinder Emergency Manifold with complete regulator, NRV, tail pipes, Middle frame & Bottom frame,

Oxygen Flowmeter with humidifier Bottle, CE Marked,

Double Locking Oxygen PB Type Gas outlets, CE Marked,

Oxygen H.P. Rubber tube white color,

Area Alarm, CE certified from Notified Body,

Area line pressure alarm-1 Gas

Isolation Valve,

Medical Grade Copper Pipeline (In Mtrs.) as per EN 13348,

12 mm (OD) x 0.7 mm Thickness

15 mm (OD) X 0.9 mm Thickness

22 mm (OD) X 0.9 mm Thickness

28 mm (OD) X 0.9 mm Thickness

42 mm (OD) X 1.2 mm Thickness

54 mm (OD) X 1.2 mm Thickness

Bed Head Panel

Bed Head Panel Provision For Gas outlet O2=1, VAC=1 with 4 switch & socket, 1000 mm size complete with wiring

Furniture

Hospital sheet Patient Bed Type - III with mattress

Patient Bed Type - I (Semi Fowler) with mattress

examination couch Type - II

Slotted Angle Rack Type -I

CHC MOIC Desk Type -VII

Desk Type -X

Computer Table

Foot Step Type -1

Instrument Trolley Type -1

Medicine Trolley Type -I

Oxygen Cylinder Trolley Type -I

Saline Stand Type -I

Round Stool Type -I

Strecher on Trolley Type - I

Chair Type V

Chair Type III

Cupboard Type -II

Wheel Chair Type - I

Chair Type -XIV

Chair Type I

OT Table

Functional Specification: 1. Height adjustment - 730mm to 1020mm from Floor to mattress Top (Motorised), 2. Trendelenburg/Rev.Trendeleburg - 30˚ / 30˚(Motorised), 3. Lateral tilt - 21˚ / 21˚(Motorised), 4. Back rest (Up / Dn - from Horizontal) - 70˚ UP/ 50˚ DN (Motorised), 5. Leg rest - Flat, 6. Head rest (Up / Dn - from Horizontal) - 45˚ UP/ 45˚ DN (Manual), 7. Leg rest abduction (Left / Right) - 0˚ - 90˚ (Manual), 8. Maximum patient Load - 200 Kgs, 9. Power supply - 220 V, 5 Amp, 50 Hz, 10. Battery Back-up - Provided fitted with OT table as emergency power back for resetting the positions., 11. Lithotonomy crutches-Adjustable along Rod Axis, Rotation 360˚ around road Axis, Crutch pad adjustable in swivel joint. Material Specification: 1. Base Assembly - Aesthetically and scientifically designed T-Shape Heavy structure made of Ms Sheet flat and MS Casting with Zinc plating finish., Base is counter balanced for stability and structure is cover with 1.6mm thick SS 304 Fabricated sheet.,

2. Column Assembly - Column is designed for self-lubricating, weldless, joint less and jerkless with high load carrying capacity.Column made by SS casting and complete assembly covered with SS 304 Fabricated sheet., 3. Table top Assembly-Top frame structure is made of SS 304 tubular frame of section 50mmX50mmX3mm Thk, 4. X-Ray Translucent top - X-Ray Translucent compressed laminate platform are provided on all sections of mattress support frame., 5. Matress - Molded Polyurethane foam mattress of density 55 Kg/Cu.m, Stitchless molded PU mattress ensure sterility and comfort, Mattresses are supported by 10mm Bakelite sheet., 6. Castor - Polyurethane twin wheel non-marking central lock heavy duty castor of wheel dia 100mm to suit the application of OT table.,

7. Actuators and Control - Back rest , Height adjustment, Trendelenburg and Lateral Tilt are operated by linear actuator of Ti-Motion make.Actuators works on powder 24VDC with duty cycle - 10% Legrest and Headrest are operated manually & Height adjustment, Backrest, Trendelenburg and Lateral tilt on actuator, 8. Crutches - Lithotomy crutches made of SS 304 Rod and molded polyurethane with ergonomic calf rest profile to suit the Operation table application. Finish Specification: 1. All SS parts - Glossy buff finish, 2. All MS Parts - Zinc plated, 3. Mattresses - Black color (molded), 4. Flexible bellow - Black color (Neoprene), 5. Calf pad - Black color (Molded) Compliances: CE, ISO 13485 & ISO 9001

Delivery Table

Material Specification: 1. Understructure - SS 304, ERW tube - section size -50 x 25 x thickness- 1.2mm, 2. Mattress support platform - Frame made of SS304 ERW tube of dia 20x20x1.2mm thickness and SS 304 sheet of 1.2mm thickness, 3. Side rail and Head rail - SS 304, ERW tube - section size-dia 16x1.2 mm thick. 4. Matress - Polyurethane foam, Mattress cover - Rexin., 5. Leg shoe - Material - nylon , Color - black. 6. Crutches - Lithotomy crutches made of SS 304 Rod and molded polyurethane with ergonomic calf rest profile to suit the Operation table application., 7. IV pole - Material SS304 ERW tube,Bigger tube dia - 19 mm thickness - 2.5 mm, Telescopic tube dia - 14 mm, SS304 Hook rod dia - 8 mm., 8. Collection tray - Material - SS304,Size: 460L x 410W x 100 mm H Finish Specification: 1. All SS parts - Glossy buff finish 2. Mattresses - PU foam in Rexin stitched cover,Color-Black. 3. Calf pad - PU Moulded with strap-Color Black Key Features: 1. Sliding leg section - Leg section can be adjusted with the help of mechanism for Gynec procedures 2. Collection tray - SS collection tray is easy to remove after the procedure 3. Safety rails - SS 304 foldable side rail / Head rail provided for patient safety on all three sides 4. IV pole mounting provision - Provision provided for IV pole Compliances: CE, ISO 13485 & ISO 9001

Infants Crib

Mattress For Crib

Paediatric Bed without Mattress

Mattress For Paediatric Bed

Over Bed Table

Partition Screen

Basin Stand

LAB TABLE

Wall Sided Lab Table

X Ray View Box

Twin Plate X-ray viewing screen designed to provide a high level of control luminance without flicker. Features: slim, Durable and effective energy efficient No UV emmision, flim active switch 4 step digital dimmer long life LED life 10000 Hour. Dimension: Frame(880 x 503 x 29 mm) Viewing area: (736 x 440 mm) Power Supply Input- AC 100-240V 50Hz. Brightness 10000 LUX, Weight 8.8 KG. It will be equipped with eight spring-loaded clips to secure the X-ray negative when in use. The X-ray viewing screen illumination shall be high frequency LED lamps, controlled by dimming balsat.

MEDCIAL EQUIPMENT 1 Basin 825 ml. ss (Stainless Steel) Ref. IS 3992 1 2 Basin deep (capacity 6 litre) ss Ref: IS: 5764 with Stand 1 3 Tray instrument/Dressing with cover 310 x 195x63mm SS, Ref IS:3993-1 4 Flashlight/Torch Box-type pre-focused (4 cell) 1 5 Torch (ordinary) 2 6 Dressing Drum with cover 0.945 liters stainless steel 1 7 Hemoglobinometer – set Sahli type complete 1 8 Weighing Scale, Adult 125 kg/280 lb 1 9 Weighing Scale, Infant (10 Kg) 1 10 Weighing Scale, (baby) hanging type, 5 kg 1 11 Sterilizer 1 12 Surgical Scissors straight 140 mm, ss 1 13 Sphygmomanometer Aneroid 300 mm with cuff IS: 7652 -1 14 Kelly’s hemostat Forceps straight 140 mm ss 1 15 Vulsellum Uterine Forceps curved 25.5 cm 1 16 Cusco’s/Graves Speculum vaginal bi-valve medium 1 17 Sims retractor/depressor 1 18 Sims Speculum vaginal double ended ISS Medium-1 19 Uterine Sound Graduated 1 20 Cheatle’s Forcep 1 21 Vaccine Carrier 2 22 Ice pack box 8 23 Sponge holder 2 24 Plain Forceps 5

25 Tooth Forceps 2 26 Needle Holder 2 27 Suture needle straight 10 28 Suture needle curved 10 29 Kidney tray 4(big) & 4 (small) 30 Artery Forceps, straight, 160mm Stainless steel 5 31 Dressing Forceps (spring type), 160mm, stainless steel 1 32 Cord cutting Scissors, Blunt, curved on flat, 160 mm ss 1 33 Clinical Thermometer oral & rectal 1 each 34 Talquist Hb scale 1 35 Stethoscope 1 36 Foetoscope 1 37 Hub Cutter and Needle Destroyer 1 38 Ambu Bag(Paediatric size) with Baby mask 1 39 Suction Machine 1 40 Oxygen Administration Equipment 1 41 Tracking Bag and Tickler Box (Immunization) 1 42 Measuring Tape 1 43 I/V Stand

Total

TOTAL NSI IN WORD