Construction of District Emergency Operation Centre (DEOC)Building in Tamulpur District.(Ground Floor with G1 provision) TN_626

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. 2.8.1 All kinds of soil

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete: 16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level : 4.1.5 1:3:6 (1 cement : 3 coarse sand (zone-III) 6: graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22A.1 Mild steel and Medium Tensile steel bars

Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete.

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts.

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers.

5.9.3 Suspended floors, roofs, landings, balconies and access platform.

5.9.7 Stairs (excluding landings) except spiral-staircases.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level : 5.1.2 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size).

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor level, excluding cost of centering, shuttering, finishing and reinforcement: 5.2.2 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand).

Half brick masonry with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.2 cement mortar 1:4 (1 cement: 4 coarse sand).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast or dash fastener shall be paid for separately). 9.1.1 Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35mm thick including ISI marked stainless steel butt hinges with necessary screws.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately): 21.1.1 For fixed portion 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron).

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately). 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron).

Filling the gap in between aluminium frame & adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer road of approved quality as per architectural drawings and direction of Engineer-in-charge complete. 21.8.1 Upto 5mm depth and 5mm width

Providing and fixing glazing in aluminium door, window, ventilator shuttters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): 21.3.2 With float glass panes of 5mm thickness (Weight not less than 12.50 kg/sqm).

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 12.1.3 0.63mm thick with zinc coating not less than 275 gm/m2

12mm cement plaster of mix: 13.4.2 1:6 (1 cement : 6 coarse sand)

15mm cement plaster on rough side of single or half brick wall of mix: 13.5.2 1:6 (1 cement: 6 coarse sand).

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.1 Fixed to steel windows by welding.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion): 2.35.3 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300mm apart including drilling 12mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor: 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

62mm thick cement concrete flooring with concrete hardener topping under layer 50mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix: 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS:15622, of approved make, in colours white, Ivory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 Cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance+1mm), with wall thickness 2.0mm (+ 0.2mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19mm and 1mm (+ 0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-charge). 9.117.1 Extruded section profile size 48x40mm

Providing and fixing to existing door frames. 9.118.1 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24mm and wall thickness 2mm (+ 0.2mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220mm having wall thickness 1.0mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (+ 0.1mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24mm and 2mm (+ 0.2mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less 620mm, having over all thickness of 20mm and 1mm (+ 0.1mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).

Cement plaster 1:3 (1 cement : 3 coarse sand) finisshed with a floating coat of neat cement . 13.9.1 12mm cement plaster

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20mm nominal size) over 75 mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand including necessary excavation, levelling & dressing & finished top smooth.

Providing and applying plaster of paris putty of 2 mm thickness over plaster surface to prepared the surface even and smooth finished.

Distempering with oil bound washable distemper of approved brand and manufacture to given an even shade. 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. 13.43.1 Water thinnable cement primer.

Finishing walls with water proofing cement paint of required shade: 13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm).

Applying priming coat: 13.50.1 with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).

Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufactures specifications: 13.48.1 Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over and under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868), transparent or dyed to required colour or shade, with nuts and screws etc, complete. 9.96.2 250x16mm

Providing and fixing aluminium tower bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868), transparent or dyed to required colour or shade, with necessary screws etc, complete. 9.97.2 250x10mm

Providing and fixing aluminium handles, ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868), transparent or dyed to required colour or shade, with nuts and screws etc, complete. 9.100.1 125 mm

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20cm in trenches, plinth.

Sanitary Works : Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito prrof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass single hole basin mixer approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever require: (a) White Vitreous China Wash basin size 550 x 400 mm with a pair of 15mm C.P. Brass single hole basin mixer.

Providing and fixing 600 x 450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.1 450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170 gms.

Providing and fixing soil, waste and vent pipes. 17.35.1 100mm dia 17.35.1.1 Sand cast iron S&S pipe as per IS: 1729

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) in S.C.I./C.I. Pipes. 17.36.2 100m dia pipe

Providing and fixing PTMT grating of approved quality and colour. 18.58.2 Rectangular type with openable circular lid 18.58.2 150mm nominal size square 100mm diameter of the inner hinged round grating.

Making soak pit 2.5m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100mm diameter, 1.8 m long complete as per standard design. 19.32.1 with common burnt clay F.P.S (non modular) bricks of class designation 7.5.

Water Supply Works Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threated fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fiitings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. Internal work- Exposed on wall 18.7.5 40 mm nominial outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threated fittings, i/c fixing the pipe with clamps at 1.00 m spcing,. This includes jointing of pipes & fiitings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. Concealed wotk, including cutting chases and making good the walls etc. 18.8.3 25 mm nominial outer dia pipes

18.8.1 15 mm nominial outer dia pipes

Providing and fixing CP brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 18.52.1 15mm nominal bore

Providing and fixing CP brass bib cock of approved quality conforming to IS:8931: 18.49.1 15mm nominal bore

Providing and fixing PTMT pillar cock of approved quality and colour. 18.56.2 15mm nominal bore, 125mm long foam flow, weighing not less than 120 gms

Providing and fixing CP brass shower rose with 15 or 20mm inlet. 18.22.2 150mm diameter.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer-in-charge. (a) 15 mm nominal dia

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 18.18.3 25 mm nominal bore

Const. of Septic Tank Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. 2.8.1 All kinds of soil.

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete: 16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level : 4.1.5 1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.1 Mild steel and Medium Tensile steel bars

Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.5 Lintels, beams, plinth beams, griders, bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platform.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level : 5.1.3 1:2:4 (1 cement: 2 coarse sand (zone-III) : 4 graded stone aggregate 20mm nominal size).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand).

Half brick masonary with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundations and plinth in: 6.12.2 cement mortar 1:4 (1 cement : 4 coarse sand)

12mm cement plaster mix: 13.4.2 1:6 (1 cement : 6 coarse sand)

Cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement. 13.9.1 12mm cement plaster

Supplying and fixing C.I. cover without frame for manholes: 19.18.2 500mm diameter C.I. cober (medium duty) the weight of the cover to be noit less than 58 kg.

Electrical Wiring for light point/fan point/exhaust fan point/call bell point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit,with modular switch,modular plate, suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc.as required. 1.10.1 Group-A

1.10.2 Group-B

1.10.3.Group-C

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor,single core cable in surface/recessed medium class PVC conduit as required. 1.14.2 2x2.5sq.mm+1x2.5 sq.mm earth wire

1.14.3 2x4sq.mm+1x4sq.mm earth wire

1.14.5 2x10sq.mm+1x6sq.mm earth wire

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc.as required. 1.24.1 5/6 A switch

1.23.3 15/16 A switch

1.23.4 3 pin 5/6 A socket outlet

1.23.5 6 pin 15/16 A socket outlet

1.24.8 Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/modules,GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1.27.2 3 Module (100mm x 75mm)

1.27.4 6 Module (200mm x 75mm)

1.27.5 8 Module (125mm x 125mm)

Supplying and fixing following Modular Base & cover plate on existing modular metal boxes etc.as required. 1.28.2 3 Module

1.28.4 6 Module

1.28.5 8 Module

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/wooden block including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable fort single phase, 230 V, complete as required.

Supplying and fixing PVC batten/angle holder including connections etc.as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/recess, complete with tinned copper busbar, neutral bus bar, earth bar, din bar, inter connections, powder painted including earthing etc. as required (But with out MCB/RCCB/Isolator). 2.3.2 8 way, Double door

Supplying and fixing 5A to 32 A rating, 240/415 V,10 KA, "C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc.as required. DB complete with connections, testing and commissioning etc. as required. 2.10.1 single pole

2.10.3 Double pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.12.1 40A

Earthing with G.I earth pipe 4.5metre long, 40mm dia including accessories,and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.with charcoal/coke and salt as required.

Supplying and laying 6 SWG G.I wire at .50 metre below ground level for conductor earth electrode,including connection with GI thimble etc,as required.

Laying of one number PVC insulated and PVC sheathed XLPE power cable of 1.1 KV grade of following size direct in ground including excavation,sand cushioning,protective covering and refilling the trench etc as required. 7.1.1 Upto 35 sq.mm

Supplying and fixing of 32mm dia x 2.00 metres long G.I pipe (medium class) bracket for mounting of fluorecent/HPMV/HPSV street light fitting on pole including bending the pipe to the required shape, 2 nos 40mm x 3mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc.as required.

Supplying, Installation, Testing and Commissioning of 1200mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3nos. Blades, 30cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerence as per IS:374-2019), THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying with including fitting fixing of ADORE LED PLUS 9W/10W etc. as required & directed by the Deptt.

Supplying including fitting fixing of 20 W three color CCT change LED batten which can change the color of batten from warm white to natural white to cool white with the help of a simple toggle switch, etc. as required and directed by the Deptt.

Supplying with including fitting and fixing of Metal Exhaust Fan (300 mm) Aeroclean LD GBD etc. as required and as directed by the Deptt.

Supplying with fitting & fixing of 50W IP 65 Street Lights/ Campus light with best in class design & Robust heat sink along with class leading IP, IK & Surge protections for long lasting performance, etc.as requitred and as directed by the Department (Orient, Bajaj, Havells or equivalent make).

Supplying, installation with fitting & fixing of LUMINOUS UPS system including UPS Battery Trolley (LUMINOUS Inverter Sine Wave, Model No. ECO VOLT + 1650 and TALL Tubulat Battery-150 Ah, Model No. PC18042) as required and directed by the department.

Supply of following size PVC/ XLPE insulated and PVC sheathed 1.1 KV Gd. Solid Aluminum conductor up to 10sqmm, balance stranded conductor, XLPE insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminum wire for single core up to 70sq.mm, balance Aluminium strip, Galvanised wire for cables up to 2x10sq.mm, 3x10sq.mm, 4x6 sq.mm & balance all galvanized steel strip), extruded PVC Type ST2 sheathed, 650/1100 V grade as per IS 7908 (Part-I) 1988 armored U.G cable as specified and directed by the deptt. (Havells, RR or equivalent make as approved by this Deptt.) Considering 100 Mtr. length). 10.00sq.mm 2 Core U.G Cable

Supplying with, fitting and fixing Single Phase Digital type Energy Meter tested with APDCL including Load Security, Meter security, Labour charge and connection charge with all accessories materials as required complete as directed by the deptt. (Load = 3 KW).

DHARAMSING NARZARY (BID ID -268244)

PINKU NARZARY (BID ID -268247)