COMPREHENSIVE MAINT AND MISC REPAIRS AT ZONE A AREA UNDER AGE BR II OF GE SUKNA

Amount

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and directed.

Removing Excavated soils not exc 50 M and depositing where directed at a level not exc 1.5 M above the starting point complete all as specified and directed.

M&L for Plain Cement Concrete 1:3:6 Type C2 (using 40 mm graded stone aggregate) in surface channels and drains including necessary formwork complete all as specified and directed.

M & L for plain Cement Concrete 1:2:4 Type B0 (using 12.5 mm graded stone aggregate) in roof kerbs, rounded or chamfered on haunching in chajjas to prevent water seepage into brick walls, including necessory formwork and scafolding upto a height of 8 mtr including demolition of existing PCC complete all as specified and as directed.

M&L PCC 1:2:4 type C-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L for Precast cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for Manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 and including demolition complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L 25 mm thick (measured solid) precast cement concrete 1:2:4, type-B-0 (using 12.5mm graded stone aggregate), louvers and jallies, including all mouldings but excluding frame, set in cement Mortar (1:4) including demolition of existing cement concrete complete all as specified and directed.

M&L RCC nominal mix 1:2:4 type B1 as in slab supported on walls ,beams and coloumns in floors, roofs, landings, kitchen slabs etc complete all as specified (Reinforcement shall be measured and paid seperately) including demolition of old concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L for forming fair finished drain or channel 30 cm Type B0 in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

Supply only liquid water proofing compound ISI mark.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M& L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting n.exc. 10 cm in girth complete all as specified and directed.

M&L 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like laid over and including screed bed 15 mm thick in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

S&F 40 mm thick factory made flush door shutter solid core construction ,with black board core and plywood face panels,commercial type, both fare covered with decorative face veneer with lipping/frame to match complete all as specied and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description not exceeding 1.0 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 10 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling of grid size 605 x 605 mm including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F non asbestos fibre cement building boards 4 mm thick (designer pattern) fixed or laid / inserted to GI framework with screws in seamless false ceiling (flat or sloping) of grid size 605 x 605 mm and including GI frame work comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with contacting clips across the intermediate channel at 457 mm centre to centre hanging from structural steel / scantling with 6 mm GI wire and including dismantling complete all as specified and directed.

S&F anodised aluminium snap grid frame work of grid and 12 mm thick medium density fibre board, exterior grade, fixed to aluminium frame work timber framework with screws in ceiling flat or sloping complete all as specified and as directed.

M&L for plaster of paris fancy moulding pattern in corners of ceiling in triangular shape of size 75 mm x 75mm including finished upto the required mark complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges with screws complete all as specified and directed.

S&F in repair 40 mm continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 150 mm Aluminium handles cast type, anodised and fixed complete all as specified and directed.

S&F in repairs mortice locks suitable for aluminium door of 100 mm size 4 lever aluminium body vertical type as per existing or sample complete all as specified and directed.

S&F in repairs 20 mm Harrison rails, mild steel chromium plated with and including suitable CP brackets complete all as specified and directed.

S&F in repair towel rail 20 mm dia type brass chromium plated 600 mm long between flanges complete all as specified and directed.

S & F in repair Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 140 mm complete all as specified and directed.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width of and of weight between 61 to 80 Kg (extruded section) complete all as specified and directed.

S & F Galvanized mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples including wooden beads complete all as specified and directed.

S & F in repair Rubberised door seal 50 mm width including fixing with nails or adhesive with door complete all as specified and as directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips complete all as specified and directed.

S&F Roof truss (framed) trussed, purlins,crane gantires of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1998 grade St-240 including one shop coat of zink chromate primer paint including preparation of surface including dismantling complete all as specified and directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

M&L in repair for welding exc 6 cm but n.exc 9 cm (thickness of metal to be welded) for hinges with door frame etc complete all as specified and directed.

M&L in repair for welding in Running welding for thickness of metal exc 9 mm but n.exc 20 mm complete all as specified and directed.

M&L Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed as per architectural drawings and the directions of Engineer-in-Chief.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) Taking out of existing water proofing treatment and including padding, cleaning the surface using wire brush, brooming down and washing down with water to remove dust etc, and brushing with neat cement slurry @ 3.00 kg of cement per Sqm. (ii) 15 mm thick screed bed in CM 1:4 on surface. (iii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm. (Contd...)

(iv) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (v) Applying one coat of water proofing paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction. (d) APP based polymeric membrane shall be manufactured by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (e) Water proofing paint shall be by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited

M&L 18/19 mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work in cup board shutters, partitions, shelves and similar work with teak wood beading at the edges complete all as specified and as directed.

M&L 12 mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work in cup board shutters, partitions, shelves and similar work with teak wood beading at the edges complete all as specified and as directed.

S&F Prelaminated particle board 9 mm, exterior grade, prelaminated both side with one side with decorative choice lamination & other side balancing white lamination fixed with screw to timber/aluminium frame work with suitable beading/snap grid complete all as specified and as directed.

M&L machine cut kota stone slab 20-25 mm thick as in skirting, dado, riser of steps, plinth, etc, laid over and including 15 mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the stone and including rubbing / grinding and polishing complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25 mm (minimum) thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab and including rubbing and polishing and laid over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection, sub base, floors, paths, hardstanding etc. finish even and smooth without using extra cement complete and laid fair in alternate bays and construction joint to be given at every 3m interval and corners of buildings and is including filled joints with bituminous mastic or equivalent filler complete all as specified and directed.

M&L 100 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base finished even and rough complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 type B0 (using 12.50 mm graded stone aggregate) in floorings including finishing the surface even and fair to receive floor finishes complete all as specified and directed.

Roughening surfaces of old concrete floor or concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc. and applying neat cement slurry with 3 kg of cement per sq. metre complete all as specified and as directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 cm thick backing with cm 1:3 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for double charged premium quality 10 mm thick vitrified ceramic tiles light shade (square / rectangular) polished, area of each tiles n.exc.0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for double charged premium quality coloured vitrified ceremic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exc 0.36 Sqm in vertical surface in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:3 complete all as specified and as directed.

M&L Pre-polished cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 15 mm thick on other than fair faces of brick work or concrete sur-faces in cement mortar 1:4 using water proofing compound @ 3% by wt of cement for finished even and smooth (without using extra cement) complete all as specified and directed. (WPC will be measured and paid separately)

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for prepration of new plastered surfaces of wall and applying two coat of oil emulsion distemper over a coat of primer over a thin layer of wall care putty on wall surfaces complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil emulsion distemper over a coat of primer over a thin layer of wall care putty to obtained smoothness of plastered surfaces complete all as specified and directed.

M&L for prepration of new plastered ceiling surfaces and applying two coat of oil emulsion distemper over a coat of primer over a thin layer of wall care putty complete all as specified and directed.

M&L for prepration of old plastered ceiling surfaces and applying one coat of oil emulsion distemper complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of cement base paint complete all as specified and directed.

M&L preparation of old plastered wall surfaces and including applying one coat of cement base paint complete all as specified and directed.

Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

All as per Sl. item No. 80 above but on old surfaces.

S & F sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick frosted on one side sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 sq.M in each panes complete all as specified and directed .

S&F 4 mm (plus minus 0.50 mm) thick Sheet glass, ordinary quality and glazing with oil putty or in rubber beading with one way film in squares exceeding 0.5 Sq. M in each pane complete all as directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from steel/wooden frames or stones, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

M&L for preparation of new painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of Synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint complete all as specified and directed.

S&F in replacement 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F in replacement 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F in repair Unplasticised PVC pipe 40 mm bore of preassure rating 10 kgf/Cm2 with one end with socket complete all as specified and directed.

S&F in repair Unplasticised PVC waste pipe for urinal / WHB 32 mm bore of pressure rating 10 kgf/cm2 with one end with socket complete all as specfied and directed.

S&F in repair rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), including 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 250 ltr to 500 ltr capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 1000 to 2000 ltrs capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

S&F in repairs 15 mm bore bib tap chromium plated fancy type, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F pillar tap 15 mm bore, fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. Make - Jaquar Cat No - CON-011KN or equivlant.

S&F in repairs 15 mm bore brass CP wall mixture, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. Make - Jaquar Cat No - CON-219KN or equivlant.

S & F in repair 15 mm bore CP stop valve fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in repair angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, concealed type, chromium plated long thread with flange complete all as specified and directed.

S&F in repairs waste fitting 32 mm bore, brass, chromium plated for basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repairs Ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm - 210 gms ) complete all as specified and directed.

S&F in repairs Ball valves 25mm dia high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 25 mm - 455 gms) complete all as specified and directed.

S&F in repairs 32/40 mm bore waste coupling of PTMT (half or full threaded) (minimum weight 32mm-45gms / 40mm-60gms) complete all as specified and directed.

S&F in repair 100mm dia PVC gratings, doom type, fixed to floor trap complete all as specified and as directed.

S&F PVC connections 15 mm size with PTMT nuts, of length 450 mm & suitable for cold/hot water supply complete all as specified and directed.

S & F in repair of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including taking down complete all as specified and directed.

S & F in repair of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including taking down complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) branch piece single, (single Y) equal or unequal, complete all as specified and directed.

S & F in repair 110 mm bore PVC (SWR) branch piece single, (single Y) equal or unequal, complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) junction single, (single T) equal or unequal, complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) junction double, (double T) equal or unequal complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) vent cowl fixed in position including taking down complete all as specified and directed.

S & F in repairs of 125 / 110 mm size PVC (SWR) gully trap, setting and jointing with solvent cement including top cover grating complete all as specified and directed.

M & L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore pipe and including dimantling old pipes complete all as specified and directed.

M & L in repair 150 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed in CM 1:1 complete all as specified and directed.

Cutting into existing manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

S & F in repairs sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers, waste coupling and waste pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 495 mm x 420 bowl size 410mm x 330mm x 160mm fixed complete all as specified and directed.

S&F in repair swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets & flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed.

S&F in repairs plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges for european water closet pan complete all as specified and directed.

S&F in repairs vitreous china counter top wash hand basin, oval shape, self rimming type, white of size not less than 560mm (L) x 410mm (B) with and including PVC waste pipe 32 mm bore, CP waste fitting, cutting for and pinning in ends of brackets etc, complete all as specified and directed. Make - Hindware Cat No - 10017 or equivalent in Cera, Paryag

S & F for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. Make - Jaquar Cat No CAN-1171N or equivalent in MARC

S & F in repairs Vitreous China Squatting pan of Orissa pattern, size 580x440 mm size white with integral foot rest with Cast Iron `P' or `S' trap, front or back inlet and including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete bedding complete including making good to floor (excluding flushing cistern and flush pipe)all as specified and directed.

S&F in repair 15mm dia 2 way stop cock/angle stop cock fancy type chromium plated type complete all as specified and directed.

S&F in repairs health faucet 12 mm bore, ABS chromium plated with & including 1.0 mtr chromium plated flexible tube & wall hook and connection with angular stop cock complete all as specified and directed. Make - Jaquar Cat No ALD-565 or equivalent in MARC

S&F 15 mm bore jet spray chromium plated, with and including 1.5 mtr flexible steel tube complete all as specified and directed. Make - Jaquar Cat No ALE-547 or equivalent in MARC

S&F as in repairs brass CP basin mixture chromium plated 15mm bore with capstan head, screwed reed down high pressure with or without lettered "hot" or "cold with long scewed shanks and fly nuts screwed for iron pipe complete all as specified and directed. Make - Jaquar Cat No. CON-167KNB or equivalent.

S&F in repair plate rack of 750 x 600 x 210 mm of stainless steel minimum 0.63mm thick of existing design complete all as specified and as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Dismentling of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails or screws complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

R N SAH N CO (BID ID -3106432)

SHANTI UDYOG (BID ID -3112059)

SHIVALAYA ENTERPRISES (BID ID -3104167)

PS ENTERPRISE (BID ID -3105512)

M/s TRIMURTI ASSOCIATE (BID ID -3107350)

G C DUTTA N CO (BID ID -3109407)

SHRI N.DAS (BID ID -3104048)

VICKY ENTERPRISES (BID ID -3103293)

KARMIBRINDA (BID ID -3112979)