NIT No GE/ND-60/2024-25

Amount

B&R PORTION: M & L for Providing and injecting chemical chlorpyrifos emulsifiable concentrate for Post Constructional Anti termite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M & L for Anti termite Treatment of soil under existing floors using chemical chlorpyrifos emulsifiable concentrate @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and directed.

Providing & injecting chemical emulsion at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 ltrs per hole by drilling holes at a down ward angles of 45 degree at 150mm center to center & sealing to same complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of reinforcement to facilitate demolition complete all as specified and directed.

M&L for reinforced cement concrete (Design mix) M-25 (20 mm graded stone aggregate) as in fins, slab ,facias, louvres, parapets, and railings, newels, balustrade, and the like complete all as specified and directed.

S&F TMT bars 10 mm dia & over as in reinforcement of columns, beams, RCC, slabs, chajjas, lintels etc cut to length bent to shape required including cranking, bending, spirally hoping for columns, hooking ends and welding the new reinforcement with old steel bars complete all as specified and directed.

S&F 8mm dia TMT bars, cut to length bent to shape required including cranking bending spirally for hoping for columns, chajjas to parapets etc hooking ends and binding with mild steel wire not less than 0.90mm dia complete all as specified and directed.

M&L for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pilasters, buttresses, etc.; vertical or to better, fair finishes complete all as specified and directed.

M&L Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for chipping out spilled and loose concrete cover and derusting steel reinforcement of concrete column, beam, slab, chajjas, parapets and the like as directed up to 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforcement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part of sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out up to 10 metre height) complete all as specified and directed at site. Note :- (a) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guniting is done with polycretes admixture @ 2% by weight of cement all as per manufacturers instructions (polycretes admixture shall be procured from chemical adhesive Pvt Ltd Co or their authorised dealer). (c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account.

M& L for fixing rebar of required length & diameter for structural connection in RCC slab, Beams and similar situations including power drilling holes of appropriate diameters in reinforced or plain concrete upto depth minimum 100 mm or as per manufacturers specification, fixing the reinforcement in position using epoxy Arcylate based anchoring adhesive at all heights and levels, 16 mm dia hole suitable for inserting 12 mm dia reinforcement bars complete all as specified and directed.

M& L for fixing rebar of required length & diameter for structural connection in RCC slab, Beams and similar situations including power drilling holes of appropriate diameters in reinforced or plain concrete upto depth minimum 100 mm or as per manufacturers specification, fixing the reinforcement in position using epoxy Arcylate based anchoring adhesive at all heights and levels, 14 mm dia hole suitable for inserting 10 mm dia reinforcement bars complete all as specified and directed.

M& L for fixing rebar of required length & diameter for structural connection in RCC slab, Beams and similar situations including power drilling holes of appropriate diameters in reinforced or plain concrete upto depth minimum 100 mm or as per manufacturers specification, fixing the reinforcement in position using epoxy Arcylate based anchoring adhesive at all heights and levels, 12 mm dia hole suitable for inserting 08 mm dia reinforcement bars complete all as specified and directed.

S&F TMT bars 5 mm dia upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with with mild steel wire (annealed) not less than 0.9mm dia or securing with clips including U-shaped stirrups with necessary welding required at site complete all as specified and directed.

Demolition of brick work built in Cement morter or cement lime mortar incl all quoins, arches , pillar etc complete all as specified and directed.

M&L for Brick work with sub class "B" bricks , straight or curved on plan exc 6 m mean radius built in cement mortar (1:6), complete all as specified and directed.

M&L Brick work with sub class "B" bricks , straight or curved on in half brick thick wall built in cement mortar (1:4), complete all as specified and directed.

M & L for Dismantling of brick tiles (laid flat or on edge) on roof surface laid bedded and pointed in any mortar complete all as specified and directed.

M & L for Demolition of mud fuska in roof, any thickness, including plastering and leaping upto two storey bldg incl necessary scaffolding arrangement complete all as specified and directed(whether full thickness removed or only a part there of) and removing from cantonment area or as directed complete all as directed by Engr in charge and specified.

M&L for cement concrete 1:2:4 type B0 (using 12.50 mm graded stone aggregate) as in levelling coarse over RCC slab to bring the desired slope up to six storied Bldg, using water proofing compound as per manufacturer instruction complete all as specified & directed. Note:- Water proofing compound shall be measured and paid separately.

M&L for APP based polymeric membrane plain finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints complete all as specified and directed.

S & F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner complete all as specified and directed.

M & L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work complete all as specified and directed.

Demolition of stone slab and tiles of any description or thickness on steps, jambs, pillars, walls, cooking platform, floors, aprons, skirting etc laid bedded and pointed in any mortar complete all as specified and directed

M & L for Granite (of any type) work, 18-20 mm thk (table rubbed and polished) in cooking platforms, lift wall, skirtings where ever required and likes on cement mortar bedding of 20mm thick in CM 1:6 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges with shade of granite complete all as specified and directed.

M&L for drilling holes for pipes etc n exc 25mm dia in cooking platform hole in granite complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed wth pigments to match the shade of the slab including rubbing and polishing 15mm thick screed bed in Cement Mortar 1:6 and roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L for Non Skid ceramic tiles 8 to 10 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and directed.

M&L for Glazed ceramic tiles of approved colour and design in vertical surfaces 300x450x7mm thick including provision of high lighter tiles/boarder and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for Glazed ceramic tiles of approved colour and design in flooring 600x600mm jointed in neat cement slury and pointed in white or coloured cement to match incl 15mm thick screed beding cement mortar 1:6 and roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L for Glazed ceramic tiles of approved colour and design matching flloring, as in skirting laid on 10 mm thick cement plaster in CM (1:4), set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles complete all as specified and directed.

S & F in repairs Vitreous China squatting pan ‘Orissa’ pattern, size 580 x 440 mm, coloured, with integral foot rests, fixed in repairs including provision of lime concrete bedding complete. Squatting pan including connection to trap, and to flushing pipe, anti-siphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repairs low level flushing cistern of 10 ltrs capacity PVC valveless, dual tank , syphonic action type, white with inlet ball valve float and handle complete all as specified and directed.

S&F in repair , brass chromium plated Health Faucet including flexible pipe of 15 mm bore and 1.20M long with and including 15 mm bore complete all as specified and directed. Make: Jaguar Cat Part No ALD-573 or equivalent of make as specified in PS.

S & F in repair Vitreous China wash basin with pedestal white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed.

S&F as in repair chromium plated shower rose of size 100 x 100 mm square (ABS Chrome plated with rub it cleaning system) with or without swivel joints any type including chromium plated shower arm fixing to steel pipe and union complete all as specified and directed. Make: Jaguar Cat Part No BSH-1751 or equivalent of make as specified in PS.

S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repairs 6 mm thick glass corner shelf fancy type with railing and fitting complete of size 25cm x 25 cm of best quality (as per sample approved by Engr -in-charge) complete all as specified and directed.

S&F in repair fancy type glass corner 300mm radius of 10mm thick toughened glass with CP railing fixed with screws fancy type complete all as specified and directed.

S&F in repairs wash hand basin mixer 15mm dia CP brass fancy type including joints to steel pipe or unions complete all as specified and directed. Make: Jaquar cat part no ORP-10011 BPM or equivalent of make as specified in PS.

S&F in repair 15mm dia chromium plated quarter turn wall mixer hot & cold L bend 3 in 1 pattern fixing and connection to pipes, complete all as specified and directed. Make: Jaquar Cat No FLR5281N, CERA Cat No F2008401, Hindware Cat No F570022 or equivalent of make as specified in PS.

S&F in repairs Kitchen sink mixer 15mm dia CP brass fancy type including joints to steel pipe or unions complete all as specified and directed. Make: Jaquar Cat No ARI39309 or equivalent of make as specified in PS.

S&F in repairs bib tap with crutch or butterfly handle, quarter turn screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium plated long body with flange complete all as specified and directed. Make: CERA (Cat part no. F1001151), Prayag (Cat Part no. 9106), Somany (Cat part no. 272211150031) or equivalent of make as specified in PS.

S&F in repair bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed to 15mm bore complete all as specified and directed.

S&F in repair fancy type chromium plated quarter turn brass angle valve type suitable for 15mm bore pipe complete all as specified and directed. Make: Jaquar Cat No FLR 15053PM, CERA Cat No F1001201, Hindware Cat No F570043 or equivalent of make as specified in PS.

S&F in repairs Good quality Connection pipe (PVC) 15 mm dia and 450/600mm long complete all as specified and directed.

Dismantling of floor of size not exceeding 1.50 Sqm mtr for IWC/EWC water closet and removing out the cinder/concrete from sunken portion, , grinding any sharp edges etc all as specified and directed with following: (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (d) M&L for providing 40 mm dia GI pipe spout projecting at least 150 mm beyond outer face of wall. (e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion is n.exc 1.50 Sqm each. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. (h) 72 hrs Ponding test shall be carried out for sunken treatment before payment.

Taking down chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

M & L for Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in back filling, hold fasts etc, complete all as specified and directed.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e. depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: stainless steel butt hinges shall be paid separately under relevant item)

Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /cum Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardware should be fixed with 19*6mm size steel screws etc complete all as specified and directed Engineer-in-charge, manufacturer's specification & drawings.” Note: Fixture/fittings shall be measured & paid under relevant item

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, as per specification & drawing and as per drawing on SI page 180 of SSR (part II) complete all as specified and directed.

S&F factory made solid PVC Moulded Door shutter ,28 to 30mm thick with 2 raised pannels design with 2mm thick Moulded PVC Sheet on front face and 2mm plain colour PVC sheet on back face in frame at site as per specification and drawing on SI page no 181 of SSR (part II) with particle board core complete all as specified and directed.

S&F powder coated aluminum frame/guiding rail for sliding or side hung window/ventilators and for sliding shutters with one or more rebates incl jointing cleats for fixing etc complete all as specified and directed.

S&F rubber gasket for fixing of glass into window/ventilator shutters complete all as specified and directed.

S&F alluminium locks for locking arrangement of sliding window shutters complete all as specified and directed.

S&F powder coated aluminum glazed/gauzed window and ventilators shutters powder coating side hung type without sash bar aluminum section weighting 0.55 kg per mtr. Including necessary joining cleats glazing clips rubber packing anodised aluminum bading screws including fittings such as peg stays 150mm long hinges 100mm long suitable handle complete all as specified and directed.

S&F 5.5mm thick sheet glass ordinary quality in square exc 0.50 sqm each including grinding of edges for crockery cupboard/aluminium window shutters complete all as specified and directed.

S&F powder coated aluminium ornamental grills for window fram complete all as specified and directed.

Dismantling wrought iron or mild steel/ iron work of any description (steel window & Grill) complete all as specified and directed.

M&L for Mild steel Framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe 290 Gde-E-165 complete all as specified and directed.

M&L for Applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation on new steel surfaces any description, not otherwise described over 10 cm width or girth complete all as specified and directed.

S&F stainless steel wire cloth of size 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed tinned tacks or galvanised wire staples complete all as specified and directed.

S&F 100mm long (size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin complete all as specified and directed.

S&F stainless steel AISI 304 grade barrel tower bolt 200mm long, extruded section, etc. complete all as specified and directed.

S & F Hasp and staple -100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws complete all as specified and directed.

S&F in repair 25 mm dia SS curtain rod stainless steel AISI 304 , with fixing of brackets, side knobs of good quality as approved complete all as specified and directed.

S&F 75 mm long L Bihari concealed type auto closing hinges incl stainless screw complete all as specified and directed.

S & F 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, complete all as specified and directed.

S&F 300mm long, stainless steel , sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, and fixing bolts and sliding bolts complete all as specified and directed.

S&F 150mm long stainless steel barrel tower bolt of extruded section, complete all as specified and directed.

S&F 200mm long stainless steel barrel tower bolt of extruded section, complete all as specified and directed.

S&F 150mm size stainless steel AISI 304 grade fancy type handle complete all as specified and directed.

S&F stainless steel AISI 304 grade floor door stopper with twin rubber shoes double door stopper 75 mm long complete all as specified and directed.

S&F 100mm long extruded fancy D' type type SS handle for kitchen cup boards shutters, cabinets, crockery shelf drawers fixed with nuts , screw and washer complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18 mm and fixed stainless steel wire staple, complete all as specified and directed.

S&F 4.00 mm thick figured glass, pin head type and glazing with wooden beads, glass putty, PVC beading, aluminium beads, complete all as specified and directed.

S&F mortice lock of size 100mm with Brass fancy type and vertical type 4 levers with key in duplicate (Make : Harrison/Godrej) complete all as specified and directed by Engineer-in-Charge.

S&F mortice night latch of size 100mm, 4 levers of mild steel complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (40mm graded stone aggregate) as in sub base , and mass concrete complete all as specified and directed.

M&L for Cement concrete 40mm thick type B-1, 1:2:4 (using 20mm graded stone aggregate) in floors pavings etc finished even & smooth with out using extra cement complete all as specified and directed.

M & L for Cement concrete 1:3:6 type C1 using 20mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement, complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore complete all as specified and directed.

Taking up or down steel tubing and connections of 20mm bore complete all as specified and directed.

Taking up or down steel tubing and connections of 25mm bore complete all as specified and directed.

Supplying and laying of CPVC 20mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl brass coupling fittings complete with fitting as required complete all as specified and directed.

Supplying and laying of CPVC 25 mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl brass coupling fittings complete with fitting as required complete all as specified and directed.

Supplying and laying of CPVC 32 mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl brass coupling fittings complete with fitting as required complete all as specified and directed.

Dismantling water tanks of capacity exceeding1000 litres but not exceeding 2000 litres complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) white colour hoisted and fixed in position complete all as specified and directed.

S & F in repairs PPR gate valve, for iron pipe 20 mm bore complete all as specified and directed.

S & F in repairs PPR gate valve, for iron pipe 25 mm bore complete all as specified and directed.

S & F in repairs Sinks with drainage board made of 1mm thick stainless steel for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, including PVC waste pipe 32 mm bore, 65 cm long complete all as specified and directed.

S&F in repair 75mm dia cast iron spun pipe soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed.

All as per item No 99.00 above but fixed on walls complete all as specified and directed.

S&F in repair 100mm dia cast iron spun pipe soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed.

All as per item No 101.00 above but fixed on walls complete all as specified and directed.

S & F in repair 75mm dia (bore of pipe) branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified and directed.

S & F in repair 100mm dia (bore of pipe) branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified and directed.

S&F, in repairs, cast iron floor trap with Cockroach Proofing CP grating with or without hole including jointing to waste pipes , fixed in cement concrete type B-1 (1:2:4), dia of outlet 75 mm, complete all as specified and directed.

S&F in repair Salt Glazed Stone Ware (SGSW) gully traps square or round mouthed type size 150x150mm including excavation/earth work, bed concrete, surrounding concrete and CI grating, complete all as specified and directed.

S & F in repair PVC (SWR) pipes single socketed, 50 mm bore in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F in repair PVC (SWR) bends/Tees of any radius of 50 mm bore complete all as specified and directed.

S & F in repair Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for any bore and any type of pipes complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc including removal of debris from the MOD land complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers i.e.. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) mixed with WPC finished even and fair etc complete all as specified and directed. Note:- WPC shall be measured and paid separately

M&L for rendering 10 mm thick in CM 1:6 on internal brick/concrete wall surfaces of any description, and finishing the surfaces even and fair without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and fair without using extra cement complete all as specified and directed.

Supply only integral water proofing admixture of approved quality complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of walls applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats Distempering with, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

M&L for preparation of old decorated surface (plastered or unplastered) of walls by complete removal of existing treatment by mechanical grinder and applying cement base wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats Distempering, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of ceiling applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

M&L for preparation of old decorated surface (plastered or unplastered) of ceiling by complete removal of existing treatment by mechanical grinder and applying cement base wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats Distempering of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and providing and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified as directed by Engr-in-charge.

M&L for preparation of old decorated plastered surfaces of walls, complete removal of existing treatment by rubbing , brooming down, washing with water etc and providing and applying plaster of Paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : old work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified as directed by Engr-in-charge.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/ Bathroom/ Toilet/ Kitchen & Cabinets complete all as specified and directed.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/ Bathroom/ Toilet/ Kitchen and Cabinets complete all as specified and directed.

S&F 75 mm long L Bihari concealed type hydraulic hinges incl stainless screw complete all as specified and directed.

S&F 15mm mild steel, chromium plated rod with fixing brackets, fixed in cupboards for hanging cloth of adequate strength complete all as specified and directed.

S&F stainless steel AISI 304 grade handle of size 75 mm long, etc. complete all as specified and directed.

S&F Magnetic catch for wooden cupboard with complete closer mechanism claps and clips fix with stainless steel screw complete all as specified and directed.

S&F in repair steel rolling shutters, thickness of lath 1 mm, with ball bearing including hood cover made out of MS sheet thickness not less than 1mm, anchoring rod and hasp & staple, including mild steel lock plate and handle made out of flat iron 35x5mm, including guide channel and bracket plate made out of MS sheet thickness not less than 3.15mm, roller, spring as suitable size and plate and locking arrangement and including two coat of synthetic enamel paint and one shop coat of primer erected in position where required (in patches or whole), complete push pull or manual type complete all as specified and directed as per SSR part -I 2009.

S & F Continuous (piano) hinges width of flap 30 mm, mild steel, bright finish or electrogalvanised fixed to steel chowkhat with welding or with screws complete all as specified and directed.

S&F stainless steel of AE - SI 316 grade tubular towel ring including a pair of CP brass bracket complete all as specified and directed.

S&F 4.00 mm thick figured glass, pin head type and glazing with wooden beads, glass putty, PVC beading, aluminium beads, complete all as specified and directed.

S&F stainless steel peg set of 6 peg, 45 centimeter long, complete all as specified and directed.

Cutting shrubs, wild growth, plants not exc 30 cm girth grown on permanent structures and removing same from roots and stopping the recurrence by injecting herbicide Glyphosate 4+ solution (04 % concentrate) into plant root to eliminate further growth. Application shall be as per manufacturer instructions. The disturbed area shall be repaired with PCC (1:2:4) Type B0 mix and surface finished even and smooth in cm 1:4 incl applying two coats of matching finish of adjacent area complete all as specified and directed.

Dismantling A.C/Fibre sheet corrugated or semi corrugated sheet in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for cleaning of RCC OHT of capacity upto 2,000 Ltrs cleaning walls & floors of tanks by wire brushing & gunny bags etc removing all scale, dirt & mud etc and removing out side the MOD land including washing with bleaching powder and painting the internal surface with black Japan bituminous paint complete all as specified and directed.

M&L for outdoor tile parking tiles size 300 x 300 mm conforming to IS 15622:2017 including 20mm screed bed in CM 1:6 as in flooring complete all as specified and directed.

M&L for PU Coated Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade complete all as specified and directed.

M&L for Sand filling under floors tiles including watering and consolidation complete all as specified and directed.

M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed

Forming Jambs etc to opening incl cutting toothing and properly bonding in to old work complete new work built in CM 1:4 complete all as specified and directed.

Cutting holes in bricks walls built in cement mortar or cement lime mortar or stone walls built in lime mortar for inserting hold fasts and making good the dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-I exc. half brick but not exc one brick complete all as specified and directed.

E&M PORTION: Taking down carefully old point wiring with aluminium/ copper conductor (Light / Fan/ Socket/ power Point ) complete including fixture and fittings such as switches, light fittings,ceiling rose, pendent holders, bell, regulators and socket,light fittings etc .removing materials to store for keeping in safe custody or for taking credit and making good the disturbed surface & wall/ floor complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit 20 mm dia medium grade ISI marked and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators for one light/ fan point controlled by one no, one way 5 Amp switch complete all as specified and directed. Note: (i) Cutting chases for concealed conduit and making good in cement mortar is deemed included in unit rate. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling point wiring. In this specified portion wire shall run through the existing conduit or surface new conduit shall be provided as required. (iii) In case the wiring is encountered with any beam/column, then the wiring will run on surface to avoid any damage to the RCC portion.

All as per item No 144.00 above but One bell/buzzer point controlled by one bell push button complete all as specified and directed.

All as per item No 144.00 above but One three pin socket outlet 5 amps point controlled by one no, one way switch on independent board complete all as specified and directed.

All as per item No 144.00 above but One three pin 5 Amp socket outlet point controlled by one no, one way switch on same board complete all as specified and directed.

All as per item No 144.00 above but with 2.5 sqmm (for phase, neutral) and 2.5 sqmm (for continuous earth wire) cable for one 15/16 amp socket out let point on independent board complete all as specified and directed.

S&F in repair modular switch 230/250 volts grade one way SP 6 Amp rating complete all as specified and directed.

S&F in repair modular bell push 230/250 volts grade one way SP 6 Amp rating complete all as specified and directed.

S&F in repair modular switch 230/250 volts grade one way SP 16 Amp rating complete all as specified and directed.

S&F in repair modular socket out let shuttered type flush mounting type, 230/250 volts grade 2/3 pin 6 Amp combined 2 module type complete all as specified and directed.

S&F in repair modular socket out let shuttered type flush mounting type, 230/250 volts grade 2/3 pin 16 Amp combined 2 module type complete all as specified and directed.

S&F in repair electric bell AC 230 Volt ding-dong type complete all as specified and directed.

S&F in repair factory made SPN DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 8 way SPN 220 Volts, with suitable busbar, neutral link & earth link suitable complete all as specified and directed.

S&F in replacment of MCBs, SP 6 to 32 Amps, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs complete all as specified and directed. Note: Make of the MCB should be the same as that of DB

S&F in replacment of MCBs, SPN 40 Amps, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs complete all as specified and directed. Note: Make of the MCB should be the same as that of DB

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing in repair LED lights fitting 1x 20W, 220V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in repair building security light of 60 watt LED type with swan type MS pipe to fix the light into wall completet all as specified and directed

S&F in repair submain wiring with PVC insulated unsheathed copper conductor cable, multi stranded, single core, FRLSH type, 1100 volts grade 2 x 1.5 sqmm complete drawn in existing conduit along with 1x 1.5 sqmm PVC insulated unsheathed copper conductor cable, multi stranded, single core, FRLS type for continuous earth wire and connected to common earth dolly complete all as specified and directed. Note :- New conduit of suitable size with connected fitting will be laid if there is a burnt/blokage/damage to the existing conduit including bends/elbows/tees/Junction boxes including making good to disturbed surface finished with the adjoining surface of disturbed area and the rates are inclusive of quoted rates.

S&F in repair VTPN 4 way to fix SP MCB as outgoing and TPN as incoming complete all as specified and directed. Note: Rate of 63 Amp TPN deemed to be included in the quoted rate

S&F in repair XLPE cable 4 core 16 sqmm through wall by using a suitable size clamps complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 460mm sweep with, blades, and frame and louvers complete all as specified and directed.

S&F in repair ceiling fan 5 star rating (Opal white)Energy saving BLDC Fan , economy range high speed having full copper motor & ribbed alluminium blades for higher air delivery,power coating provides longer life complete with accessories 230 volts 1200 mm sweep,300 RPM with air delivery 255/265 Cum/min including making arragement to hanging of fan to ceiling with proper hook nut bolts complete all as specified and directed. Note: Old unsv item shall be submitted to MES store yard

S&F in replacement stepped type modular electronic fan regulator on the 2-module modular sheet etc. as required complete all as specified and directed.

S&F in repair submain wiring with PVC insulated unsheathed copper conductor cable, multi stranded, single core, FRLSH type, 1100 volts grade 2 x 6 sqmm complete drawn in existing conduit along with 1x 6 sqmm PVC insulated unsheathed copper conductor cable, multi stranded, single core, FRLS type for continuous earth wire and connected to common earth dolly complete all as specified and directed. Note :- New conduit of suitable size with connected fitting will be laid if there is a burnt/blokage/damage to the existing conduit including bends/elbows/tees/Junction boxes including making good to disturbed surface finished with the adjoining surface of disturbed area and the rates are inclusive of quoted rates.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

sony engineering works (BID ID -3115024)

BEHAL TRADERS (BID ID -3099493)

M/S SONU ENTERPRISES (BID ID -3099373)