Refurbishment of Category - D and E Type Houses Phase - 33 in Kalpakkam Township

Amount

Excavating trenches of required width by mechanical means (Hydraulic excavator / manual means) for pipes, cables etc., for depth upto 1.5m in all kinds of soil including excavation for sockets, dressing of sides, ramming of bottoms, getting out the excavated soil and then refilling the soil as required in layers not exceeding 200mm in depth, consolidating each deposited layer by ramming, watering etc., and disposing of surplus excavated soil as directed within a lead of 50m, (Disposed soil to be leveled by breaking clods, if any and neatly dressed), etc., all complete as per specification.

Providing and laying in position of plain cement concrete using hard granite broken stone for all insitu leveling courses in foundations, floor, roof screeding, encasing pipes, etc., including mechanical mixing, ramming, compaction, leveling, curing, dewatering, if any including the cost of formwork etc., all complete as per specifications.

1 : 3 : 6 (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size)

Filling in depression with cement brick aggregate concrete 1:2:4 using 20mm size broken brick aggregate including compacting, curing etc., all complete upto Floor V level

Supplying, placing in position and removing Formwork for all insitu concrete works including sloped roof and arches etc., as per drawings and specifications, all centering, scaffolding complete (Note: Measurement for the formwork shall be the area of forms in contact with concrete surfaces).

Providing and fixing double scaffolding system (cup lock type) on the exterior side at all height made with 40mm diameter M.S. tube spaced @ 1.5m center to center at both horizontal and vertical tubes, joining with cup and lock system with M.S.tube, M.S.tube challies, M.S clamps and M.S staircase system in the scaffolding for working platform etc., and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners connection with the building, etc., Wherever required for the inspection of work at required location with essential safety features for the workmen, etc., complete as per directions and approval of Engineer-in-charge. (Note: The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding.)

Providing and casting insitu Reinforced Cement Concrete 1:1.5:3 using machine crushed hard broken granite stone of nominal size 20mm including mechanical mixing, transporting, placing at all lifts, vibrating, consolidation, curing, finishing smooth all exposed faces, for all insitu concrete items, etc. as per drawings and specifications. Note : The rate quoted shall be exclusive of reinforcement and formwork which will be paid for separately under relevant items.

Providing, cutting, bending, placing and binding Steel reinforcement using TMT bars of Fe-500 grade in all reinforced cement concrete works including cutting, bending, fixing, tieing in position with 1.6 mm dia soft drawn annealed binding wire, cost of cover blocks in C.M 1:2, etc., complete as per specifications and drawings. Important Note: The required quantity of steel reinforcement as mentioned in the schedule should be procured by the contractor only of SAIL, Rashtriya Ispat Nigam Limited (VIZAG), TATA Steel & JINDAL from authorized dealers which shall conform to IS: 1786 (Latest Edition).

Providing and constructing brick masonry at all lifts in cement mortar 1:5 using well cured flyash bricks of class 5 (non-modular) made up of using Flyash + Sand + Lime + additives (Gypsum/Cement) with waterproofing chemicals and accelerators confirming to IS-12894 or latest edition including suitable scaffolding, raking out joints, continuous curing for specified period and dismantling the existing brick work, disposing the dismantled debris within 2 kms lead etc., etc., all complete as per specifications and as directed by the Engineer-in-charge.

Providing and constructing 110mm thick brick work for partition/kerb walls in cement mortar 1:4 using well cured flyash bricks of class 5 (non-modular) made up of using Flyash + Sand + Lime + additives (Gypsum/Cement) with waterproofing chemicals and accelerators confirming to IS-12894 or latest edition including suitable scaffolding, raking out joints, continuous curing for specified period and dismantling the existing brickwork, disposing the dismantled debris within 2 Kms lead etc etc., all complete as per specifications and drawings.

Providing and laying Indian Patent Stone Flooring with cement concrete 1:2:4; 20mm thick using 10mm and below size hard broken stones including dismantling the damaged portion of existing floor/dadoo, preparation of surface, consolidating, curing, rubbing the surfaces smooth, providing dividing strips, disposing the dismantled debris at suitable places as shown at site within 2Km lead, etc., all complete as per specification and as directed by the Engineer-in-charge.

Providing and fixing Granite of Ruby red/Jet Black colour (16 - 18mm thick) gang saw cut mirror polished, (pre moulded and prepolished slab) machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1 : 4 (1 cement : 4 coarse sand) with joints treated with white cement mixed with matching pigment, epoxy touch ups, etc., including rubbing, curing, finishing, providing holes of required diameter, providing opening to fix counter basins, providing grooves wherever required, etc., all complete at all levels as per specifications. (Note: The Granite stones slab shall be got approved by the Engineer before making bulk order.)

Providing and fixing Granite of Ruby red/Jet Black colour (16 - 18mm thick) gang saw cut mirror polished, (pre moulded and prepolished slab) for kitchen shelves, etc., including cutting a chase of appropriate width with chase cutter, embedding (min 40mm) the stone into the chase with epoxy grout or with cement concrete 1:2:4 or white cement, finished smooth, etc., all complete as per specification and as directed by Engineer-in-charge. (Note: Exposed area will only be measured for payment.)

Repolishing the Mosaic flooring and skirting with medium and fine polishing using 120 to 150 and 320 to 400 grit corborundam stones with the use of floor polishing machine/Hand polishing including washing thoroughly with soap powder and wax polishing, etc., as per specification and as directed by the Engineer-in-charge.

Repairing and rectifying the minor repair works like wall cracks, floor cracks, spalling of mortar on sides of doors, windows, wall and door joints, including the cost of materials, T&P using CM 1:3 etc., all complete as directed by the Engineer-in-charge.

Providing water proofing treatment at sunken portion of toilet, utility, bathroom etc,. with two coat of two component highly flexible polymer modified cementitious water proofing coating of make FAB chemical (Mixguard AC) or Bostik (Boscolastic) or equivalent including preparation of surface free from dust/oil/grease, sealing the UPVC sleeve pipes using non shrink grout mortar over bonding coat using SBR chemicals and sealing the joints with polyester fleece along the periphery of UPVC pipes, appling two coat of water proofing etc,. all complete as detailed below as per manufacturer specification and as directed by Engineer-in-charge. Surface preparation: The surface to receive water proof treatment shall be cleaned to make sure that the surface free from dust, dirt, laitance, debris, loose mortars, oil particles etc., which may negatively affect the adhesion of water proof treatment with mother concrete surface. Sealing bore hole gap around the sleeve pipes: The gap around the pipe shall be filled with non shrink grout mortar of make FAB chemicals (Mixgrout NS) or equivalent and providing necessary slurry tight form work to enveloping the pipe with a bead of 6 to 8mm and 5mm above the surface level along with a sealer coat of make FAB chemical (Mixprime AC100) or equivalent and seal with saturated polyester fleece all along the periphery of pipes. Water proof treatment: Providing and applying two coats of two component Highly elastomeric flexible polymer modified cementitious cold applied water proof coating of make FAB chemical (Mixguard AC) or Bostik (Boscolastic) over the prepared surface to cover complete area, finishing etc. Extend the coating up to a minimum of 300mm height to the adjoining wall as per manufacturer specification.

(Note:- 1) All the sunken portion shall be tested for the water leaking before and after treatment by filling with water for 24hours and grouting shall be carried out if any leakage found. 2) The treatment should be done by an agency specialized in the job having sufficient knowledge of waterproofing treatment. 3) Five years guarantee from the date of completion of maintenance period shall be given by the contractor in the prescribed format of the department for the workmanship and the materials provided.)

Providing and laying first quality Jointless Polished Vitrified tiles of 600 x 600mm size with water absorptions less than 0.08% conforming to IS: 15622 of JOHNSON (Marbonite-PVT-DC) or KAJARIA (PVT-DC) or other approved make for flooring and skirting in all colours, shades and design of approved pattern including setting over base layer of 20mm thick in cement mortar 1:4, jointing with grey cement slurry @ 3.3 kg per sqm or by using tile adhesive of approved make, grouting the joints with epoxy based joint filling material or other equivalent jointing materials, curing, cleaning the surface with acid wash etc., all complete as per specification and as directed by Engineer in charge. (Note:- The sample shall be got approved by the Engineer-in-charge before making bulk order)

Grouting the joints of Vitrified tile flooring laid using spacer block having joints (3 - 5mm width) by using approved colour epoxy based tile grout of make Kerakoll (Fugalite® Eco) or other approved make including mixing the hardener and mix as specified, filling/ grouting using required tools, finishing, cleaning the residual traces of grout over the tile surface, finishing complete as per manufacturer specification and as directed by Engineer-In-Charge. [Note: Finished tile area will be measured for payment purpose]

Providing and laying 1st quality Rectified (Jointless) Ceramic floor tiles (Glazed or Anti-skid) of size 300x300 mm or more confirming to IS : 15622 of KAJARIA (Approved concept of Digital Series) or SOMANY (Digital Series - Glasstra) or JOHNSON (Approved concept of Satin & Rustic / Glossy series) or approved equivalent make in all colours, shades in Floors laid over 20 mm thick cement mortar 1 : 4 (1 Cement : 4 sand), jointing with grey cement slurry @ 3.3 kg per sqm including dismantling the existing insitu mosaic or terrazzo tile flooring, preparation of surface, grouting the joints with white cement and matching pigments, curing, disposing the dismantled debris at suitable places shown at site within 2Kms lead, etc., all complete as per specification.

Providing and fixing 1st quality Rectified (Jointless) Glazed ceramic wall tiles of size 300x450 mm or more of approved concept series confirming to IS 15622 of 'KAJARIA (Digital Series) or JOHNSON (Satin &Rustic / Glossy series)] or SOMANY or other approved make in all colours and shades in Skirting, Risers of steps and Dados laid over 12 mm thick bed of cement mortar 1 : 3 (1 Cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm or by using Cement based high polymer modified quick set tile adhesive (water based) or other approved tile adhesive including providing Motiff tiles as per approved concept, pointing in white cement mixed with pigment of matching shade, chipping the existing insitu mosaic / plastering or cuddappah stone dadoo, preparation of surface, disposing the dismantled debris at suitable places shown at site within 2Km lead, etc., all complete as per specifications and as directed by Engineer-in-Charge.

Supplying and fixing of Rigid PVC nosing of approved quality and colour at the corners of Ceramic tiles dadooing including finishing all complete as directed and as per specifications.

Providing Half Round Edge Moulding to 16-18mm thick marble / Granite or 20-25mm thick Kota stone counters, vanities, sills, etc. including machine polishing the edges to give high gloss finish etc., all complete as per specifications and as directed by Engineer - in – charge.

Granite work

Providing and laying in position of Mortar Bund of size 50x40mm (upto 1.00 metre length) in Cement Mortar 1:3 (1 Cement: 3 sand) at sill level of doors including dismantling the existing bund, disposing the debris, making exposed surfaces smooth with cement slurry, curing, etc., all complete as per specifications and as directed by Engineer -in-charge.

Providing and laying in position of Mortar Bund of size 50x50mm in Cement Mortar 1:6 (1 Cement: 6 sand) at terrace level of checking for water seepage/leaks in the ceiling of houses including dismantling the mortar bund for after seven days of stagnating water and disposing the debris, making surfaces smooth etc., all complete as per specifications and as directed by Engineer -in-charge.

Supplying and fixing 20mm to 25mm thick both side polished cuddapah stone slabs for Shelves in Cupboard/Wardrobe/Shoe rack, tumbler slabs etc., including removing the existing wooden tiers, fixing by cutting a chase of appropriate width with cutter and embedding the stone into the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) finished smooth, front face polishing, rounding the edges, etc., all complete as per specifications and as directed by Engineer-in-charge. (Note: Cudappah stones shall be got approved by the Engineer before making bulk order)

Providing and fixing 14-16mm thick table rubbed White Agaria Marble Stone slab of following size and fixed in shelves, above wash basin, bath, etc., including cutting a chase of appropriate width with chase cutter, embedding (min 50mm) the stone into the chase with epoxy grout or with cement concrete 1:2:4 or white cement, finished smooth, rounding the exposed edges, polishing, etc., all complete as per specification and as directed by Engineer-in-charge. (Note: Size of the slabs indicated are the exposed area of shelves i.e., excluding embedded area.)

600x125mm size for wash basin

250x250mm Corner round for bathroom

Repairs to the wall and ceiling cracks by chipping and removing the damaged portion upto 20 to 30mm deep, 100 to 200mm wide and plastering with CM 1:3 including making grooves over cracks, grouting with cement slurry or approved crack filling compound, providing Glass fibre mesh, applying necessary approved quality bonding chemicals, finishing the surface, curing, white washing two coats, disposing the debris within 2Kms lead etc., all complete as per specification and as directed by the Engineer-in-charge.

Repairs over the spalling on concrete members by chipping and removing the damaged portion and plastering with CM 1:3 including cleaning the surfaces, applying rust converter of approved quality, filling the damaged portion with cement concrete wherever required, applying necessary approved quality bonding chemicals, finishing the surface in layers, curing, white washing two coats, disposing the debris within 2Kms lead etc., all complete as per specification and as directed by the Engineer-in-charge.

Providing and fixing best quality Stainless Steel sink with Drain board of overall size 1040 x 510mm (Bowl depth 200mm) of make 'NIRALI / PRAYAG' or other approved equivalent make of 1mm thick Stainless Steel grade AISI-304 (18/8) as per IS-14283, including fixing over opening in RCC slab of platform or supplying and fixing CI bracket pair and placing the sink over the platform/bracket to correct line and level, basket type choke stop stainer, waste coupling with check nuts, providing flexible hose from waste coupling to Nahani trap or Waste line, finishing the platform surface with white cement or other approved grouting materials etc., all complete as per IS-14283 specifications and as directed by Engineer-in-charge.

Plastering with Cement Mortar 1:5, 12mm thick for brickwork / Concrete on its internal faces at all lifts including scaffolding, curing and forming grooves wherever necessary all complete as per specifications and as directed by the Engineer-in­charge. [Note: 6mm premium glass fibre of make Dugar & Co or Recron shall be mixed with Cement @ 60 gms of glass fibre per 50kgs of cement]

Plastering with Cement Mortar 1:5; 20mm thick for brickwork / concrete, finished smooth including scaffolding, curing and forming grooves wherever necessary and including chipping the plastering, applying bonding agents, disposing the dismantled debris, etc all complete as per specifications and as directed by Engineer.

Providing and applying SBR based bond coat of make MC Bauchemie (Naufufill-SBR) or FOSROC (Nitobond SBR) or FAB Chemical (Mixbond SBR) or Bostik (Boscocem 475) or other approved make including preparation of surfaces by scrubbing / cleaning the fungus / stains, cleaning with water, filling the cracks with approved crack filler and including cost of all materials, labour, tools and plants, curing, scaffolding at all lifts, etc., all complete as per specifications and as directed by Engineer-In-Charge. (Note: Mixing ratio of chemicals, consumption and application shall be as per manufacturer specifications.)

Supplying and laying of one course of Vitrified Cool Roof tiles over roof slab / sloped surface of terrace and skirting using tiles of size 300x300mm and 10mm (±5%) thickness of make SOMANY (or) JOHNSON (or) PAVIT or approved equivalent make and conforming to IS: 15622 (Group B1a (or) Group B1b) approved colour with SRI (Solar Reflectance Index) > 78, Solar reflection > 0.70 & initial remittance >0.75 laid on 20mm thick bed on Cement mortar 1:4 mixed with integral water proofing admixture including removal of dead mortar from roof slab, cleaning the surface, exposing floor & wall function along parapet and column if any, sealing the floor & wall junction with water proofing mortar, laying screed concrete in CC 1:2:4 to form slope and haunch portion along parapet, if any required including laying tiles with required slope as per manufacturer specification, grouting the joints with approved tile grout, etc., all complete as per manufacturer Specification and as directed by Engineer-in-Charge. (Note:- Cost of screed concrete in CC 1:2:4 will be paid for separately under relevant item.)

Providing and laying machine made 20mm thick burnt clay flat terrace tiles of size 230x230mm conforming to IS 2690 ( Part - I) of make Nuvocotto or other equivalent make colour and pattern over roof at all elevations jointed with cement mortar 1:4 (1 Cement : 4 Coarse sand) mixed with 2% of integral water proofing laid over a bed of 20mm thick cement motar 1:4 (1 Cement : 4 Coarse sand) and finished neat complete.

Providing Flush pointing on roof tiles by removing the damaged pointing over existing roof tiles, cleaning, removing any growth of vegetation, washing thoroughly, pointing the joints with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement including filling the gap with polymer modified mortars or other approved water proofing chemicals etc., all completed as per specification and as directed by Engineer-in-charge.

White/Colour washing One Coat of lime solution using shell lime of approved quality admixed with glue, ultra marine etc., on existing surfaces of walls and ceiling at all lifts including cost of all materials, labour, scaffolding, removing nails, brooming down the surfaces for removing cobwebs, smoke dirt etc., filling the holes, cracks, crevices with Snowfilla or other suitable filler materials, covering the furniture by suitable covering materials, cleaning/removal of white washing splashing and dropping from floors, doors & windows, electrical fixtures, etc., all complete as per specifications and as directed by the Engineer-in-charge.

Painting all internal faces of walls / plastered surfaces with Two coat of Interior Emulsion paint of make Asian (Tractor) / Berger (Bison) or other approved equivalent make of approved shade over a coat of interior wall primer of make Asian (Professional) / Berger (BP Primer) or other approved equivalent make including preparation of surfaces by scrapping the existing white wash / colour wash using scrapping machine with dust free vacuum collection system, cleaning the existing white wash/colour wash area, roughening the surface, washing the area thoroughly with lime and soda mix or other approved chemical using high pressure washer, preparing the surface dust free for applying the primer coat, applying approved make wall care putty to make surface smooth without porous by using putty knife and sand papers, the dust accumulated during scrapping shall be collected in appropriate dust bin collector / equipment and disposed with in an initial lead, etc., all complete as per specification and as directed by Engineer-in-charge. (Note: The sample shall be got approved by the EIC before making bulk order.)

Providing Painting over all exposed surfaces at all heights over rough cast plaster/plain plaster with Two Coats of premium exterior emulsion paint of make Asian (APEX - Dust proof exterior emulsion) / Berger (Anti dustt weather coat) or other approved equivalent make of approved shade over a coat of exterior wall primer of make Asian / Berger or other approved equivalent make including preparation of surfaces, curing, scaffolding etc., all complete as per specifications.

Painting over Plain Plaster at all lifts.

Painting over Roughcast Plaster at all lifts.

Providing painting over all exposed surfaces at all heights over rough cast/plain plaster with One coat of premium exterior emulsion paint of make Asian (APEX - Dust proof) or other approved equivalent make of approved shade or match with existing shade over the coat of Highly flexible cementious two component coat water proofing treatment system over the coat of bond coat including making surface free from dirt/oil/other materials by scrapping the surface, removal of loose/ cracked mortar, filling the cracks using approved crack fillers, filling/injection/ grouting the cracks/joints where ever required with polymer modified cement mortar using admixtures, scaffolding, etc., all complete as detailed below as per manufacturer specifications and as directed by the Engineer-in-Charge. i) Surface preparation: Remove the existing coatings, paints, etc., Seal the surface cracks by cutting 'V' shaped grooves and filling with crack & using seal compound. Clean the surface thoroughly to remove the dirt's and contaminates and keep dry prior to the primer application, debonded or weak plaster must be replaced with polymer modified mortar. ii) Bond Coat (1st Coat) : Applying Base primer bond coat with of make FAB chemical (MIXBond AC) or Bostik (Boscocem 476) over the existing surface. Mixing ratio consumption and application procedure shall be as per manufacturer specifications. iii) Highly flexible cementious water proofing coat (2nd & 3rd Coat): Applying 2 component waterproofing coating of make FAB Chemical (Mixguard AC) or Bostik (Boscolastic). Duration between these two coats shall be minimum 4 hrs. Mixing ratio of chemicals, consumption and application procedure shall be as per manufacturer specifications.

For one coat of exterior emulsion over Plain Surface iv) One coat of external wall primer (3rd coat): Applying one coat of external wall primer of make Asian or other approved equivalent, consumption and application procedure shall be as per manufacturer specifications. v) One coat of premium exterior emulsion paint (4th coat): Applying one coat of premium exterior emulsion paint of make Asian (APEX - Dust proof) or other approved equivalent make of approved shade or match with existing shade. Mixing ratio of paint, consumption and application shall be as per manufacturer specifications. Note: Cost for plastering will be paid for separately under relevant item.

Providing Terracotta Painting over compound wall/Honey comb wall / Roof tiles / facia tiles at all heights with one coat of Acrylic Emulsion paint of make Asian (APEX - Dust proof exterior emulsion) / Berger (Anti dustt weather coat) or other approved equivalent make of approved shade and colour including cleaning, preparation of surfaces by scrubbing / cleaning the fungus / stains, cleaning with water, filling the cracks with approved crack filler, curing, scaffolding etc., all complete as per specifications. Note:- 1) The samples should be got approved by the EIC before placing.

Painting with flexible polymer modified cement based anti-dampness coating for interiors using Asian Paints Damp Block or other approved equivalent make including preparation of affected surface, removing old paint / putty using wire brush / chisel to expose cement plaster, apply self priming coat of damp block (1:1 ratio diluted in water) and apply 2 coats of damp block (diluted with water in 3 part powder : 1 part water ratio) using a putty knife or a trowel to achieve total coverage of 7.5 sqft/ kg, finishing the surface smooth, etc., all complete as per specifications and as directed by Engineer.

Painting for wood work with one coat of synthetic enamel paint of approved colour and make including preparing the surface for receiving the paint by scraping, rubbing, applying wood filler, wood putty, making surface smooth, etc., as per specifications.

Painting for window grills/ shutters/ gates with Two coats of anti-corrosive paint of approved colour and make over a coat of red oxide zinc chromate primer, including preparation of surfaces for receiving the paint by scraping, rubbing, labour, scaffolding, etc., all complete as per specifications.

Polishing the staircase handrails and other wooden areas at all lifts with two coats of French polish/Touch wood of approved make including preparation of surfaces by scrapping with suitable tools or with suitable grade of sand paper, cleaning the surface dust free for applying the polish, disposing the scrapped debris, applying sealer, suitable filler materials wherever required, cost of all materials, labour etc., all complete as per specification.

Applying anti-termite chemical for new wooden frames of windows / doors/ ventilators by spraying or brushing with two coats of Dursphan / Durmat or other approved equivalent make of anti-termite chemical at the ratio of 1:19 [one part of chemical and 19 parts of kerosene] over the wood and contact masonry surface, etc., all complete as directed by the Engineer-in-charge.

Dismantling Plain cement concrete/Brick bat coba at all lifts including clearing and depositing the same with a distance of 100 metres as directed by Engineer-in-charge.

Dismantling Reinforced cement concrete at all lifts including clearing and depositing the same with a distance of 100 metres as directed by Engineer-in-charge.

Dismantling Brick work in cement mortar at all lifts including clearing and depositing the debris within a distance of 100 metres all as directed by Engineer-in-charge.

Dismantling of Tile work in floors, walls and roofs laid in CM upto 25mm thick including removal of tiles, stacking as directed, disposal of debris within a initial lead of 100m, etc., all complete.

Dismantling of 15mm to 40mm dia G.I /PVC pipe upto floor V level including scaffolding, removing the pipes and fittings without causing any damage to existing stock pipes, stacking of retrieved pipes at Departmental stores, etc., all complete as per directed by Engineer-in-Charge.

Disposal of surplus excavated earth / Debris by collecting, loading, transporting by mechanical means and unloading them at places as shown by the Department within a lead specified below and levelling, etc., all complete as per specifications and as directed by the Engineer-in-Charge. Note: 1) The rates in respect of this item are applicable for the NET Quantities arrived at after making deductions for voids @ 20% in respect of soil and @ 50% in respect of rock from the corresponding stack / truck measurements. 2) The earth shall be dumped well inside the dumping yard and not over approach pathway road.

Upto 1 Km or part thereof

Exceeding 1 Km but not exceeding 2 Kms

Replacing the existing wood work by supplying, manufacturing and fixing of Teakwood frames and architraves for doors, windows, ventilators, etc., made out of best quality Class-II teakwood scantlings with necessary holdfast / anchor fasteners, wooden plugs and screws for fixing it to the various openings including removing the old door frame/shutter with all fittings, refixing the shutter to the new frame, finishing the sides with plastering white/colour washing to match with existing surface, painting the new wood with two coats of synthetic enamel paint over a coat of primer etc., and returning the retrieved old materials to GSO civil maintenance stores, etc., all complete as per the specifications and as directed by Engineer-in-charge.

Providing and fixing Wardrobe shutters of single/double leaves made out of 8mm thick Cement bonded particle board of `Bison Panel' or approved equivalent make panels with second class teak wood frame of size 40x40 mm alround with lock rail of size 40x32 mm at the centre for each leaf including removing the old damaged shutter and returning the damaged shutter to GSO stores etc., complete all as per specifications and as directed by the Engineer-in-charge.

Repairing the cupboard shutters by removing the shutters from the existing position with all furniture fittings, removing the damaged portion of plywood panels from the shutters and replacing with 4mm thick commercial plywood including cost of cutting, finishing the edges and refixing the shutters in position with all the existing fittings and painting with two coats over one coat of synthetic enamel paint of wood primer etc., complete all as per specifications and as directed by the Engineer-in-charge.

Supplying, manufacturing and fixing of Teakwood frames with fly proof mesh shutter for windows, ventilators etc., made out of best quality Class-II teakwood scantlings with necessary wooden plugs and screws for fixing it to the various openings including removing the existing architrave beading, making outer frame using 50x25mm teak wood with half lap/mortice joint, fixing the outer frame with suitable screws, making fly proof mesh shutter using 50x25mm teak wood fixed with 0.4mm dia wire and 1.4mm aperture Stainless Steel (Grade 304) grade fly proof wire gauze, providing and fixing 19/12x12mm size teakwood beading for fixing fly proof mesh, painting the new wood with two coats of synthetic enamel paint over a coat of primer to match the existing colour, fixing the shutter with following fittings, returning the retrieved old materials to GSO civil maintenance stores, etc., all complete as directed by Engineer-in-Charge i) Fittings:- Each shutter shall be fixed with the following hardware fittings. a) 3 Nos. of 75 mm long stainless steel butt hinges of approved make bearing ISI mark with suitable stainless steel screws. b) Two numbers of 75mm long anodised aluminium tower bolt for windows and ventilators of approved make bearing ISI mark with suitable CP screws. c) One number of 125 mm long anodised aluminium D handle of approved make as per IS - 208 bearing ISI mark with suitable CP screws. Note: 1) All fittings, fly proof mesh, teak wood shall be got approved by the Engineer before making bulk order. 2) The rate quoted shall be inclusive of supplying, manufacturing, fixing of frames and shutter with required hardware fittings as detailed above.

For windows and ventilators - Outer frame and Shutter

Supplying, manufacturing and fixing of Teakwood frames with fly proof mesh shutter for balcony door etc., made out of best quality Class-II teakwood scantlings with necessary wooden plugs and screws for fixing it to the various openings including removing the existing architrave beading, making outer frame using 50x25mm teak wood with half lap/mortice joint, fixing the outer frame with suitable screws, making fly proof mesh shutter using 50x25mm teak wood fixed with 0.4mm dia wire and 1.4mm aperture Stainless Steel (Grade 304) grade fly proof wire gauze, providing and fixing 19/12x12mm size teakwood beading for fixing fly proof mesh, painting the new wood with two coats of synthetic enamel paint over a coat of primer to match the existing colour, fixing the shutter with following fittings, returning the retrieved old materials to GSO civil maintenance stores, etc., all complete as directed by Engineer-in-Charge. i) Fittings:- Each shutter shall be fixed with the following hardware fittings. a) 4 Nos. of 75 mm long stainless steel butt hinges of approved make and bearing ISI mark with suitable stainless steel screws. b) One numbers of 75mm and one number of 250mm long anodised aluminium tower bolt for door of approved make and bearing ISI mark with suitable CP screws. c) One number of 150 mm long anodised aluminium D handle of approved make as per IS - 208 bearing ISI mark with suitable CP screws. Note: 1) All fittings, fly proof mesh, teak wood shall be got approved by the Engineer before making bulk order. 2) The rate quoted shall be inclusive of supplying, manufacturing, fixing of frames and shutter with required hardware fittings as detailed above. 3) Balcony shutter shall be of folding type with required hardware fittings.

Supplying and fixing of factory made Solid PVC foam door frame of approved make with suitable rebate for shutters (Profile FP-6030) including the joints shall be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm and made by SP 5 epoxy seal and fevikwik / solvent, fixing the frame to wall with suitable dia. & length anchor fastener including removing the existing damaged door frame stacking at GSO stores, finishing the door and wall joints using CM 1:5 plaster to match with existing surface and painting with two coats of acrylic emulsion paint, etc., all complete as per manufacturer specifications and as directed by the Engineer-in-Charge.

Supplying and fixing in position single leaf Factory made flush door shutter of 25mm thickness of PVC integral foam sheet of make M/s. Jain Irrigation Systems Ltd. (Ex-cel sheet) or other equivalent approved make of white colour for flush door shutter including providing recessions for hinges, fixing with following fittings over the door frame using required fasteners, finishing all edges with mixture of PVC powder & solvent for smooth finish, etc., all complete as per specification and as directed by the Engineer-In-Charge. The door shutter shall be fixed with the following hardware fittings: - a) 4 Nos. of 75 mm long stainless steel butt hinges of GARG brand bearing ISI mark with suitable stainless steel screws. b) Two numbers of 125mm long anodised aluminium D handle of make Classic/Crown or approved equivalent as per IS - 208 bearing ISI mark with suitable CP screws. c) Two numbers of 75mm long anodised aluminium baby latch type/cranked type tower bolt with suitable CP screws. d) One number of 50mm long solid PVC door buffer with 75mm long CP screws. Note: - 1) All furniture fittings shall be of approved quality and make. 2) The rate quoted shall be inclusive of fixing of door shutters with required hardware fittings as detailed above. 3) The PVC Integral Foam shall be factory manufactured solid section of light weight sheet with fine & homogeneous closed cell structure with smooth, glossy, hard surface finish on both sides. The sheet shall have density of 500 - 600 Kg/Cum, water absorption less than 1% and tensile strength greater than 11 MPa. 4) The entire door shall be jointless shutter. 5) The sizes shall be approximately 700 mm x 2100mm, however exact dimensions shall be measured at site before manufacturing.

Supplying and fixing in position single leaf/double leaves of following thick non decorative type factory made Wood Polymer Composite (WPC) solid door shutters of approved make having density of 600 - 800 Kg/Cum, water absorption less than 1% and tensile strength greater than 12 MPa including providing aluminium lipping / Teak wood all-round if required, fixing the lipping with suitable adhesive, fixing required hardware fittings, fixing door using required screws, etc., all complete as per specifications and as directed by Engineer-In-Charge. [Note: Cost of Door frame, hardware fittings and Aluminium / Teak wood lipping will be paid for separately under relevant item.]

30mm thick WPC door

35mm thick WPC door

Attending minor repair works in doors, cupboard shutters, windows, ventilators, MS Grill mesh door etc., of various types of vaccant houses by servicing the fittings and replacing the wornout fittings if any, refixing the same, and also other carpentry related complaints if any etc., complete all as directed. Note: 1) The rate quoted shall be for each quarter category wise. 2) Retrived furniture fittings if required will be supplied by the department at free of cost (or) new furniture fittings will be paid for separately under relevant item.

Category D

Category E

Reinforcing the existing steel grills by providing extra legs of 10mm dia. MS bar including drilling holes in the window frames, inserting the legs of length upto 150mm welding the legs with existing grills using portable welding set at site, finishing the surface, etc., all complete as per specification and as directed by Engineer-in-charge.

Supplying and fixing glazed shutters having 65 x 32mm second class teakwood frames and 4mm thick clear/grounded glass for windows / ventilators including providing and fixing 19x12mm size teakwood beading for fixing glass, fixing shutter, removing the damaged window shutters, returning them to maintenance stores all as per specifications and as directed by the Engineer-in-charge.

Fabrication and fixing of doors, windows, ventilator frames, window shutters, ventilator shutters using the available old wood by cutting to required length, jointing, fabricating to required size and fixing with necessary hold fasts including removing the old painting, removing the damaged wood works, finishing the wall surfaces, white washing, applying two coats of synthetic enamel paint over a coat of wood primer, etc., complete all as directed by Engineer-in-charge. (Note:- Retrieved old wooden frame and shutters will be supplied from department store at free of cost)

Door frames

Window frames

Ventilator frames

Window shutters

Ventilator shutters

Replacing the existing damaged window / ventilator glass panes by supplying and fixing in position 4mm thick plain/grounded glass of make Saint Gobain or equivalent with necessary teakwood beading, pin nails, putty, etc., by using the existing removed beading to the possible extent and supplying and fixing balance beading if any, including cost of beading, nails, putty, etc., and transporting the removed broken glass pieces and disposing safely at places as shown etc., all complete as per specifications and as directed by the Engineer-in-charge.

Window / Ventilator glass of various sizes

Louver glass of size 600 to 750mm long, 125mm wide and 4mm thick grounded glass.

Making and fixing of Wooden PELMETS made out of Existing available wood / planks of 175 mm wide and 18 mm thick (final product) with 20 mm dia,heavy quality anodised aluminium curtain rod of 2.5 mm wall thickness and 18 mm thick teakwood brackets at interval including fixing the pelmets by rawl plugs in masonary / concrete fixing with screws, the rate shall include 3 coats of natural polishing for all surfaces all complete as per specifications and as directed by the Engineer.

Providing and fixing Aluminium curtain rod of 25mm aluminium hollow tube with 2mm wall thickness including providing end brackets, fixing over window/openings, etc., all complete as per specification and as directed by the Engineer-in-charge.

Providing and fixing Garage door shutter by using 100x35mm outer and middle frames (3 vertical and 3 horizontal) and 75x25mm intermediate horizontal 2 Nos. and pinned with 20 gauge plain GI sheet on outer face including painting entire surface with 2 coats of enamel paint over a coat of primer and removing the damaged door shutter, etc. complete.

Replacing the old night latch by supplying and fixing in position of New Ultra Verti bolt XL+ of "Godrej" (1CK Texture Brown) or approved equivalent make operable by key from outside and by knob from inside with four keys including removing the old night latch and returning the damaged night latch to GSO stores, fixing the new vertibolt using retrofit adopter over the existing night latch hole, etc., all complete as directed by Engineer-in-charge. (Note: The lock shall be got approved by the Engineer before making bulk order)

Supplying and fixing of following spares for Ultra verti bolt (Godrej - 1CK - Texture Brown (or) Ultra Verti bolt XL+ - Texture Brown) including servicing the lock, replacing the damaged part, etc., all complete as directed by Engineer - In - Charge.

PIN Cylinder assembly

Providing and fixing IS : 12817 marked stainless steel butt hinges (Heavy weight) of make GARG or approved equivalent make including fixing with suitable stainless steel screws and including removing the damaged fittings and returning the retrieved old materials to GSO Civil Maintenance stores, etc., all complete as per specification.

Providing and fixing Aluminium 75mm tower bolts / baby latch of make Classic or Crown or Hanoi or Ashoka including anodised transparent or dyed to required colour or shade, fixing with necessary CP screws, etc., all complete as per specification.

Providing and fixing IS:204 marked Aluminium tower bolts of make 'Classic or Crown' or approved equivalent make including anodised transparent or dyed to required colour or shade, fixing with necessary CP screws, etc., all complete as per specification.

Providing and fixing ISI marked Aluminium sliding door bolts (Aldrops) of size 250x16mm 'Classic or Crown or Global' or approved equivalent make as per IS 2681 including anodised transparent or dyed to required colour or shade, fixing with 5 Nos of clip and staple with necessary CP screws etc., all complete as per specification.

Providing and fixing anodised Aluminium hook and eye with suitable screws including removing the damaged fittings and returning the retrieved old materials to GSO Civil Maintenance stores, etc., all complete as per specification.

Hook and eye 250 x 6mm

Hook and eye 75mm long

Providing and fixing anodised aluminium 90mm hasp & staples of approved make conforming to IS 363 including fixing with suitable screws including removing the damaged fittings and returning the retrieved old materials to GSO Civil Maintenance stores, etc., all complete as per specification.

Providing and fixing 50mm long and 40mm dia. PVC solid door buffer with 75mm x 10mm SS screws and cup washers.

Providing and fixing Brass body with satin nickel finish Door Viewer of make Godrej or Prayag or other approved make suitable for 35-40mm thick door shutters including fixing in door as directed by Engineer-in-charge.

Providing and fixing Door Safety chain of approved shape with SS304 grade chain and satin nickel polished of make Godrej or Prayag or other approved make including fixing as directed by Engineer-in-charge.

Providing and fixing 12mm dia. heavy quality anodised Aluminium Hangers of length not exceeding 450mm for wardrobes including removing the damaged hanger, fixing the new hanger with rawl plugs and suitable cadmium plated MS screws along with bothside anodised aluminium end brackets, returning the existing damaged hanger to store, etc., all complete as directed by Engineer-in-Charge.

Repairing and refixing the existing looking mirror with fiber reinforced plastic frame including replacing the worn out rubber gasket with new gasket, replacing the damaged PVC/MDF backing with 6mm thick BWR plywood with wall fixing screw slots two nos each on vertical and horizontal side, painting with one coat of synthetic enamel paint to match with the existing surface fixing it to the wall with necessary screws, etc., all complete as per specification and as directed by the Engineer-in-charge. [Note: The required Looking mirror and frame will be issued by the Department at free of cost.]

Providing and fixing in position of 5mm thick looking mirror of make 'SAINT GOBAIN' or approved equivalent make of an overall size of 600 x 450mm with fibre reinforced plastic frame with gasket and 6mm thick BWR plywood backing with screw slots two number each on horizontal and vertical sides and fixing to the wall with necessary screws and including returning the old damaged mirrors to GSO Civil Maintenance stores, etc., all complete as per specification and as directed by the Engineer-in-charge.(Note : The looking mirror shall be got approved by the Engineer-In-Charge before making bulk order)

Replacing the wornout/damaged PVC connection by providing and fixing of 15mm x 450mm long PVC connection of approved make and confirming to IS specification both Cold and Hot water including PVC checknuts and nylon washers on both ends, fixing with GI Specials if required, returning the retrieved wornout fittings to GSO civil maintenance stores etc., all complete as per specification and as directed the Engineer-in-charge.

Providing and fixing of following heavy quality CP brass fittings of approved make conforming to IS 8931 - specification and bearing ISI mark including fixing with required SS extension nipple/GI special if required, fixing wall flange etc., all complete as per specification and as directed by the Engineer-in-charge.

15mm CP brass short body Bib cock with casing cup

15mm CP brass Two way Bib cock with casing cup

15mm CP brass pillar cock

15 mm CP brass angle cock with casing cup

20mm CP brass Concealed stop cock

Providing and fixing of heavy quality CP brass fittings of approved make conforming to IS-8931 specification including fixing with SS extension nipple if required, wall flange etc., all complete as per specification and as directed by Engineer-in-charge.

15mm Sink cock (J - Bend type)

Providing and fixing of heavy quality CP brass fittings of approved make with wall flange including fixing with suitable SS valve/cup etc., all complete as per specification and as directed by Engineer-in-charge.

32mm CP brass waste coupling ( Heavy )

100mm Square CP chrome finish shower with 300 shower arm - ABS body chrome plated.

32mm PTMT Bottle trap

Providing and fixing of following CP brass fittings to fix the sanitary fittings such as bib cock, angle cock, etc., of make Prayag or other approved make etc., all complete as directed by the Engineer-in-charge.

15mm dia. CP/SS round wall flange

Attending repairs to CP brass fittings such as bib cock, stop cock, pillar cock, push cock etc., including removing the fittings without interrupting the water supply, servicing the fittings by replacing the wornout washer if any, refixing the same, etc., all complete as directed by the Engineer-in-charge.

Labour charges for fixing the retrieved Bib tap / CP brass fittings including providing SS extension nipple, wall flange, fixing the fittings, etc., all complete as directed by the Engineer-in-charge.[Note: Required CP brass fittings will be issued by the Department at free of cost.]

Replacing the wornout/damaged Health faucet by supplying and fixing Health Faucet (hand shower-ABS Chrome plated) with 1m long flexible tube with wall hook of approved make including fixing the wall hooks, finishing the surface, providing PVC checknuts and nylon washers on both ends, returning the retrived wornout fittings to GSO Civil maintenance stores etc., all complete as per specification and as directed by Engineer-In-Charge.

Providing and fixing heavy quality 600mm CP Towel rail of approved make with wall flange including suitable CP screws all complete as per specifications and as directed by Engineer-in-charge.

Providing and fixing heavy quality 450mm CP Towel rail of approved make with wall flange including suitable CP screws all complete as per specifications and as directed by Engineer-in-charge.

Providing and fixing 300mm long plate fixed with three / four prong type anodised aluminium robe hooks approved make with suitable cadmium plated MS screws.

Supplying and fixing in position best vitreous China ware wash hand basin of size 560x440mm Inoya / 550x450mm Indus/ 550x400mm oxford of Parryware or approved equivalent make of white colour including fixing with pair of CP multipurpose rag bolt/pair (or) suitable cast iron supports painted with two coats of synthetic enamel paint over a coat of red oxide primer with necessary screws, cost of cement, etc., all complete all as per specification and as directed by the Engineer-in-charge.

Refixing the existing wash basin by removing the existing wash basin and refixing the washbasin including removing the CI brackets, old decayed teakwood plugs, fixing new teakwood plugs to wall at required height, re-fixing with new MS brackets with necessary new screws after painting with two coats of synthetic enamel paint and connecting to the inlet and outlet connection by using the existing accessories, providing GI / CPVC specials if required etc., all complete as directed by the Engineer-in-charge.

Labour charges for cleaning the existing stained ceramic sanitaryware like EWC / IWC pan, washbasin, sink etc., by using hydrochloric acid of 30% concentration, soap oil, washing powder etc. without damaging the ceramic ware including cost of hydrochloric acid, soap oil, washing powder, etc., complete all as directed by the Engineer-in-charge.

Providing and fixing high level/Low level polymer DUAL flushing cistern of 3/6 litres capacity of make "PARRYWARE/ HINDWARE model SLIMLINE" or approved equivalent conforming to IS: 7231 including fixing cistern at required height and level with necessary TW wall plugs, screws, connecting inlet and outlet, connecting the cistern and closet with suitable dia. PVC pipes and fittings conforming to IS:4985 etc., complete as per standard specifications. Note: During the above process proper care shall be taken to protect the existing IWC/EWC if any damage is taken place in IWC/EWC contractor shall replace with new IWC/EWC free of cost.

Refixing the existing high / Low level flushing cistern along with telescopic pipe by removing the existing cistern with telescopic pipe and refixing the flushing cistern with necessary PVC brackets and support at required height including connecting the cistern and closet with suitable 40mm dia. PVC pipe with necessary specials, modifying the water line if necessary, dismantling floor for removing the damaged telescopic pipe and restoring the same to its original condition etc., all complete as directed by the Engineer-in-charge. (Excluding cost of PVC pipe and GI pipe if required which will be paid for separately under relevant item) Note: During the above process proper care shall be taken to protect the existing IWC/EWC if any damage is taken place in IWC/EWC contractor shall replace with new IWC/EWC free of cost.

Repairing the flushing cistern of 'Parryware - Slimline' by supplying and fixing the following spares to flushing cistern including removing the existing flushing cistern, replacing the worn out spares with new spares, applying two coat enamel paint to exposed surface of flush tank and refixing the same in original position with working condition etc., all complete as directed by the Engineer-in-charge.

15mm dia. PVC ball cock with suitable PVC float (Inlet Assembly)

32mm dia. PVC syphon (Outlet Assembly)

15mm PVC handle knob without pulling rope.

50mm dia. rubber washer

Flush bend for EWC

Refixing in position of chinaware European type water closet with 'P' or 'S' trap with or without vent including removing the existing damaged EWC pan and refixing the same with necessary plugs, screws and packing the joints with cement mortar 1:1, and connecting the flush pipe, seat cover etc., completed all as directed by the Engineer-in-charge.

Providing and fixing PVC Nahani trap of approved make conforming to the relevant IS code, heavy quality of self cleaning design with 125mm dia. round (or) 125mm square PVC grating with perforated holes on top, including chipping the existing floor concrete, exposing the damaged Nahani trap, fixing new Nahani trap, embedding in cement concrete 1:2:4, forming circular holes by providing and fixing 110mm OD PVC pipes of required height upto floor level, jointing the outlet pipe, leveling and rendering smooth, making good the floor and wall etc., complete as per specifications. (Note: Rate shall be inclusive of cost of PVC pipe and embedding PCC.)

Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) of 20mm (Concealed on wall) Nominal Bore dia. pipes (Class-I) SDR-11 of approved make conforming to IS 15778 having thermal stability for hot and cold water supply including providing CPVC plain and brass threaded fittings, fixing the pipe with concealed clamps at 1 m spacing, jointing of pipes and fittings with 1 step CPVC solvent cement, cost of cutting chasses and making good the same, testing of joints complete, etc., all complete as per specification and as directed by Engineer In-Charge. (Note: Concealed work including cutting chases and making good the wall, etc.,)

Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (Class-I) of SDR-11 of approved make conforming to IS 15778 having thermal stability for hot and cold water supply including providing all CPVC plain and brass threaded fittings, fixing the clamps at 1m spacing, jointing of pipes and fittings with 1 step CPVC solvent cement, testing of joints, etc., all complete as per specification and as directed by Engineer In-Charge. (Internal work-Exposed on wall)

25mm dia Nominal size

40mm dia Nominal size

Supplying, fixing and testing of following dia CPVC Ball Valve Heavy duty of approved make including fixing over CPVC pipe using 1 step CPVC solvent cement, testing of joints, etc., all complete as per specification and as directed by Engineer In-Charge.

25mm dia. CPVC Ball valve

40mm dia. CPVC Ball valve

Replacing the following sizes of existing damaged PVC pipes with new PVC pipe of 10 Kg. per sq.cm pressure pipe confirming to IS 4985 of approved make bearing ISI marking including all types of specials, cutting and removing the damaged portion of the existing PVC line, replacing new PVC pipe for flush tank & kitchen waste line with suitable jointing compounds, necessary opening/ chasing of the wall, flooring, etc., without interupting the regular water supply, cost of necessary GI clamps, screws, teakwood plugs, packing pieces, restoring the same after completing the job to its original condition etc., all complete as per specification and as directed by the Engineer-in-charge.

40mm O/D PVC pipe

50mm O/D PVC pipe

Replacing the existing damaged IWC pan/Orissa pan by providing and fixing in position of following size ORISSAPAN of approved make white glazed vitreous china ware ORISSAPAN WATER CLOSET of PARRYWARE or equivalent make with "S" or "P" trap with all jointing materials including removing the damaged IWC/Orissapan, chipping out the floor, concrete, brick wall, brick bat etc., making holes in masonry, fixing the new Orissapan, jointing the pipe & Trap with Lip ring of "PRINCE" or approved make, reconstructing the same, encasing the pan and trap with brick jelly concrete 1:2:4 and back filling extra space with river sand/brick jelly concrete, including disposal of debris within 2kms lead, cost of cement required for the work etc., all as per specifications and as directed by the Engineer-in-charge. Note: 1) Cost of floor finishing will be paid for separately under relevant item. 2) Brick jelly concrete for back filling extra space with broken jelly concrete will be paid for separately under relevant item.

Orissapan of size 580x440mm

Orissapan of size 500x400mm

Providing and fixing in position of white glazed vitreous chinaware European type water closet with 'P' or 'S' trap with or without vent of make "Parryware" or any other approved equivalent make including removing the existing damaged EWC pan and fixing the new EWC pan with necessary plugs, screws and packing the joints with cement mortar 1:1, jointing the pipe & Trap with EWC pan connector of "ASHIRWAD / PRINCE" or approved make, etc., all complete as directed by the Engineer-in-charge.

Supplying and fixing of Anti-microbial solid Seat cover of `PARRYWARE' make or equivalent approved make with ISI mark of white/ colour suitable for European Water Closet of make "PARRYWARE" including fixing clamps etc., all complete as per standard specification and as directed by the Engineer-in-charge.

Replacing the damaged CI soil waste pipe by supplying, laying and fixing of PVC pipe lines laid, embedded under floor slab and fixed to walls wherever required using SWR uPVC pipes - Type B (suitable for soil and waste discharge system having wall thickness of minimum 3.2 to maximum 3.8mm) conforming to IS:13592 - latest edition with ISI mark of approved make and PVC pasting type or Ring type specials such as door bends, door tees and cowls etc. heavy quality for soil waste or vent or antisyphonage PVC pipe including removing the damaged CI pipe, chipping/removing the embedded pipe if any, fixing the new PVC pipe with suitable clamps over Teak Wood packing pieces, restoring the same to its original condition, disposal of debris within a initial lead, stacking of retrieved CI pipes at GSO stores etc., all complete as per specification and by the Engineer-in-charge.

90mm OD SWR-uPVC pipes and specials (Type B)

110mm OD SWR-uPVC pipes and specials (Type B)

Providing and fixing of Stainless Steel 304 grade 150mm Square/Circular grating of approved make including removing the damaged grating, fixing, finishing the surface to match with existing surface, etc., all complete as per specifications.

Raising the height of existing manholes of following sizes by using 230mm thick brick masonry in CM 1:6 and plastering with CM 1:5, 12mm thick including removing and refixing the manhole cover, disposal of debris, white washing two coats etc., all complete as per specification and as directed by the Engineer-in-charge.

600x450mm manhole upto 300mm

900x600mm manhole upto 300mm

Providing and constructing GULLY CHAMBER of internal finished size 300 x 300mm including providing, supplying and fixing 150 x 150mm (±10mm) PVC Gully trap with PVC grating at top of approved make including excavation in all types of soils, backfilling, embedding the trap in plain cement concrete 1:4.5:8 using 40mm size granite aggregates and constructing the chamber above the embedded PVC with 110mm thick (plus or minus 5mm) bricks in Cement Mortar 1:5 with well burnt stock bricks, plastering over both internal and external faces of brick work with Cement Mortar 1:3; 12mm thick finished smooth with a floating coat of neat cement on both faces, providing and fixing 400 x 400 x 25mm precast slab in reinforced cement concrete of 1:2:4 using 12mm and below hard broken granite stones including cost of gully trap, chamber etc., all complete as per specification.

Making connection of drain or sewer line with existing manhole including breaking in to and make good the walls, floors with cement concrete 1:2:4 mix (1cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size) cement plastered on both side with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain, etc., complete.

For pipes 100mm to 230mm diameter

Labour charges for cleaning the external area of vacant quarters by cleaning, removing cobwebs, sweeping, picking up the plastics, polythene papers, garden wastes, dry leaves and all other waste materials, conveying and disposing the waste, etc., all complete as directed by Engineer in charge.

Labour charges for cleaning the internal area of vacant quarters by brooming down cobwebs, removing the dust, waste materials including cleaning, sweeping & washing the entire floor area cleaning using cleaning powder & soap oil, the ceramic wares using acid, cleaning louver glass and window glass, cleaning waste water line from various dia of internal traps to gully chambers collecting the waste materials,conveying by suitable means, disposing/depositing at places shown by the Engineer-in-charge. (Note: Cleaning shall be carried out with out causing any damage to existing fittings / fixtures.)

Category - D

Category - E quarters including servant quarters

Electrical Estimate Supply and Embedment of following sizes of flush/surface mounting POWDER COATED SPN/TPN DB Enclosures with Double Door consisting of Phase, Neutral and Earth Bus and interconnecting wires without cable termination box, etc. at suitable depth in brick work as per the detailed specification and as directed by the Engineer-in-charge. Flush Mounting embedded in bricks work/ Wall or surface mounting as detailed Specification.

TPN, 6 Way Distribution Board with all accessories,

SPN 8 Way Distribution Board with all accessories

Surface mounting TPN 6 way Distribution Board on embedded MS Frame as per detailed Scope of work.

Removing and Re embedment of following size of flush mounting POWDER COATED DB Enclosures with Double Door consisting of Phase, Neutral and Earth Bus and interconnecting wires etc. at suitable depth in brick masonry work as per the detailed specification and as directed by the Engineer-in-charge.

SPN, 12/16 Way or TPN 4/6 Way Distribution Board

Assembling, installation, testing and commissioning of MCB DB enclosure already embedded in the wall including supply of Engraved Circuit Identification Plate and Danger Board as per the detailed specification for the following size of MCB DBs. (Refer Sec VI, Clause No.15.3).

SPN, 12/16 Way or TPN 4/6 Way Distribution Board

SPN 8 Way Distribution Board with all accessories

Supply fixing testing and commissioning of the following RCCBs and MCBs on Distribution Boards as per the detailed specification.

63 Amps, 415 V, Four Pole, Sensitivity 30 mA, "Type - AC" RCCB

40 Amps, 230 Volts, Double Pole, Sensitivity 30 mA, "Type - AC" RCCB

6 - 32 A, 240 Volts, 10 kA, Single Pole MCBs "C" Series

Supply and embedment of 50 mm Deep, Square / Rectangular Concealed type GI coated MS boxes of the following types and as specified in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification.

ONE/TWO Module

THREE Module

FOUR Module

SIX Module

EIGHT Module

TWELVE Module

Supply and fixing of following items on existing modular metal boxes as per detailed specification and as directed by Engineer in Charge

ONE /TWO Module Front Modular Plate. (Suitable for 1 / 2 Module Box )

THREE Module Front Modular Plate. (Suitable for 3 Module Box)

FOUR Module Front Modular Plate. (Suitable for 4 Module Box)

SIX Module Front Modular Plate.(Suitable for 6 Module Box)

ONE Module Blank Plate (White)

EIGHT Module Dummy Front Modular Plate (Suitable for 8 Module Box)

TWELVE Module Dummy Front Modular Plate (Suitable for 12 Module Box)

1 No. of 1 Module,10 A, 1 Way, Single Pole Switch

1 No. of 1 Module,10 A, 2 Way, Single Pole Switch

1 No. of 1 Module,10 A, 1 Way, Single Pole Buzzer / Calling Bell Switch

1 No. of 2 Module, 6 A, 5 Pin Shuttered Socket

1 No. of 2 Module, Step Type Fan Regulator

ONE Module Front Modular Plate along with 1 No. of 1 Module TV Co-axial Socket Outlet.

TWO Module Front Modular Plate along with 2 Nos of RJ11 Telephone Socket with Shutter.

1 No. of THREE Module Front Modular Plate along with 1 No. of 6 A Modular Switch and 1 No. of 6 A, 5 Pin, Shuttered Socket as per the detailed specification

1 No. of THREE Module Front Modular Plate along with 1 No. 16 A Modular Switch and 1 No. of 6/16 A, 3 Pin, Combined Socket as per the detailed specification

Two module front module plate with 1 No.16 Amps, 3 pin heavy duty shuttered type socket and 1 No. 16A, Heavy duty 3 pin indicator type plug top as per detailed specification.

Supply, installation, testing and commissioning of 1 No of 25A, SP mini MCB, C series, 3kA and One module front plate.

Supply and installation of 1 Module plate with 1No. 6 Amps, Indicator Lamp

Supply, embedment of 6 Watts LED Bulk Head fitting in RCC/Brick/ Concreate Block as per detailed Specification

Supply and installation of 25 Watt LED Light Fitting including supply of necessory fabricated brackets to mount the light fitting and 6A, 240 Volts 3 Plate, Ceiling rose as per detailed specification and as directed by Engineer in Charge

Supply and installation of 6 A, 230 V, Angle Lamp Holder along with PVC Junction Linker as per detailed Specification and as directed by Engineer in Charge

Supply and installation of Ding Dong bell along with PVC Junction Linker as per detailed specification.

Supply, installation, testing and commissioning of 6 A, 240 V, 3 Plate, Ceiling rose with PVC Junction Linker as directed by Engineer-in-charge and as per detailed Specification.

Supply, installation, testing and commissioning of 230 mm Dia, Medium duty, Wall Mounted Exhaust Fan with Double Ball bearing including required wall opening, Supply and fixing of suitable RCC color and finishing of the wall, embedment of Stainless Steel Bolts (4 Nos. of 6 mm x 60 mm) for mounting of Exhaust Fan on the wall and supply and fixing of Stainless Steel Mesh (350 mm x 350 mm) along with supply and connecting of 3 Core, 1.0 Sq.mm PVC insulated & sheathed copper flexible cables of required length and along with supply and fixing of 6 A, 3 Pin, Plug top as per the detailed specification and as directed by Engineer-in-charge.

Supply, installation, testing and commissioning of 230 mm Dia, Medium duty, Wall Mounted Exhaust Fan with Double Ball bearing on already embedded mounting bolts along with supply and connecting of 3 Core, 1.0 Sq.mm PVC insulated & sheathed copper flexible cables of required length and along with supply and fixing of 6 A, 3 Pin, Plug top as per the detailed specification and as directed by Engineer-in-charge.

Supply, installation, testing and commissioning of 1200 mm Sweep AC Ceiling Fan along with safety steel rope and 3 Core, 1.0 Sq.mm flexible copper cable including earth connection. Note: Supply and fixing of fan regulator is not included in the scope of this item and it will be measured separately through the respective item.

Carrying out healthiness check of earthing inside the house and up to EMDB level and healthiness checking of RCCB, MCB, SPN/TPN DB and all power points in Category-C/SA/FL/D&E type residential quarters as per detailed specification and as directed by Engineer in Charge.

Supply and installation of laminated Hylam sheet of 3mm thickness over the boxes as per the detailed specification.

Supply and installation of following sizes of heavy duty PVC Mini trunking on the Walls / Ceiling for routing of Power, Lighting and Telephone wires including supply of required accessories for completion of the trunking system as per the detailed specification and as directed by Engineer in Charge.

Supply and embedment of following sizes of PVC Circular Rigid Conduits for Electrical & Communication System with required Solid Long Bends, Couplings, Elbows, Tees, along with GI Pull Wire etc., in Floor, Walls, Brick, Block Masonry, etc., including chasing & replastering of brick work as per detailed specification and as directed by Engineer in Charge.

32 mm Dia, 2.0 mm wall thickness, PVC round rigid conduits with 50 mm deep Junction boxes.

25 mm Dia, 2.0 mm wall thickness, PVC round rigid conduits with 50 mm deep Junction boxes.

20 mm Dia, 2.0 mm wall thickness, PVC round rigid conduits with 50 mm deep Junction boxes.

Run of Mains wiring with 1100 Volts grade FRLS PVC insulated Copper conductor wires in existing concealed PVC Rigid Conduits, Casing & Capping including Supply and termination of copper wires at both end by crimping including supply of PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires at Energy Meter Distribution Board in the Electrical Cabin at Ground Floor and MCBDB in each Quarter/MCB DB to Power points/Switch Box to Light/Fan/power points, etc. as Follows. as per detailed specification and as directed by Engineer in Charge.

Wiring with 2 Runs of 6.0 Sq.mm for Phase & Neutral and 2 Runs of 2.5 Sq.mm for Earth

Wiring for Power Points with 2 Run of 4.0 Sq. mm Copper Wire for Phase, Neutral and 1 Run of 2.5 Sq.mm Copper Wire for Earthing.

3 Runs of 2.5 Sq.mm for Phase, Neutral and Copper Wire for Earthing.

Wiring with 2 Runs of 1.5 Sq.mm for Phase, Neutral and 1 Run of 2.5 Sq.mm copper wires for Earth

Wiring for Light/Power Points with 1 Run of 1.5 Sq.mm Copper Wire.

Wiring for Light/Power Points with 1 Run of 2.5 Sq.mm Copper Wire.

4 Runs of 6 Sq.mm (84/0.3) for Phase & Neutral and 2 Runs of 2.5 Sq.mm (36/0.3) for Earthing.(Quantity indicated is total running length of 6 Runs of Wires)

Wiring for Telephone point including supply of 1 Run of 1/0.61mm, 250 V grade PVC insulated, twin twisted, Two pair, tinned copper wire from Telephone Junction Box near staircase in each floor to Telephone point in Living hall in each quarter in concealed PVC Conduit pipe/Casing Capping including connection (Quantity indicated is Running length of 1 Run of wire)

Wiring for Television point including supply of RG-6 (21-F) Co-axial cable from terminal junction box to the TV point provided in the living hall in each Quarter in existing concealed PVC Rigid conduits/Casing & Capping including connecting the same to the socket. as per the detailed Specification. (Quantity indicated is running length of 1 Run of Wire)

Removal and reinstallation of following Electrical Items as per the site condition and as per the detailed specification and as directed by the Engineer-in-Charge.

Various sizes of switch boxes including termination of wires in the switch boxes.

Rerouting of existing wiring in the already laid PVC trunking including retermination.

Removal of Old Wiring, Light Fittings, Fuse DB, Switch Boards, Embedded Pipes, Junction Boxes, Pull Boxes, Telephone DB etc., partially or full in Category - C/SA/FL/D&E type Residential Quarters and returning them to Departmental Stores GSO/IGCAR at plant site as per site condition and as per the detailed specification and as directed by the Engineer-in-Charge.

Type D & III-B type Quarters.

Type VE type Quarters.

Cleaning of Ceiling / Exhaust/Pedestal / Wall mounting/Air circulator Fans/ fitted at different levels in various labs/Buildings as per the scope of work.

Supply, Installation, Testing and Commissioning of Static Energy Meters in place of Faulty / Defective / Old Energy Meters along with necessary fixtures and fixing arrangements including removal of Existing Meters as per the detailed specification and as directed by Engineer-in-charge.

1 Phase 10-60A Static Energy Meter

3 Phase 10-60A Static Zigbee Energy Meter

EC Enterprises (BID ID -3199458)

M/s. Ashok constructions (BID ID -3199733)

Bidder Name

M/s. Ashok constructions

EC Enterprises

K.GANESH